acpi_integer is now obsolete and removed from the ACPICA code base,
replaced by u64.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
libata currently doesn't retry if a command fails with AC_ERR_INVALID
assuming that retrying won't get it any further even if retried.
However, a failure may be classified as invalid through hardware
glitch (incorrect reading of the error register or firmware bug) and
there isn't whole lot to gain by not retrying as actually invalid
commands will be failed immediately. Also, commands serving FS IOs
are extremely unlikely to be invalid. Retry FS IOs even if it's
marked invalid.
Transient and incorrect invalid failure was seen while debugging
firmware related issue on Samsung n130 on bko#14314.
http://bugzilla.kernel.org/show_bug.cgi?id=14314
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Interestingly, when SIDPR is used in ata_piix, writes to DET in
SControl sometimes get ignored leading to detection failure. Update
sata_link_resume() such that it reads back SControl after clearing DET
and retry if it's not clear.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: fengxiangjun <fengxiangjun@neusoft.com>
Reported-by: Jim Faulkner <jfaulkne@ccs.neu.edu>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 871af1210f enabled 32bit PIO for
PATA piix but didn't for SATA. There's no reason not to use 32bit PIO
on SATA piix. Enable it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When sata_promise encounters an overrun or underrun error it
translates that to a libata AC_ERR_HSM, causing a hard reset.
Since over/under-runs were thought to be rare and transient,
this action seemed reasonable.
Unfortunately it turns out that the controller throws overrun
errors when e.g. hal polls a CD or DVD writer containing blank
media, causing long sequences of hard resets and retries before
EH finally gives up.
This patch updates sata_promise to classify over/under-runs as
AC_ERR_OTHER instead. This allows libata EH and upper layers to
retry or fail the operation as they see fit without the disruption
caused by repeated hard resets.
This fixes a problem using a DVD-RAM drive with sata_promise,
reported by Thomas Schorpp. I also tested it on a DVD-RW drive.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: thomas schorpp <thomas.schorpp@googlemail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
In March 2008 commit 0ac4a3c2fb ("ACPI: fix
ATA_ACPI build") made CONFIG_ACPI_DOCK be selected by CONFIG_ATA_ACPI because
of a build error when CONFIG_ATA_ACPI=y and CONFIG_ACPI_DOCK=m.
However, in September 2008 commit 898b054f3e
("dock: make dock driver not a module") removed the possibility of having
CONFIG_ACPI_DOCK=m and therefore there is no need for selecting it when
CONFIG_ATA_ACPI=y.
This makes the kernel ~5 Kb smaller for people who don't have a dock by
allowing them to not have ACPI_DOCK compiled-in because of ATA_ACPI=y.
Signed-off-by: Carlos R. Mafra <crmafra@aei.mpg.de>
Cc: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
By default, the PATA pins are routed to the async address lines in which
case, no peripheral muxing needs to be done. However, if the pins get
routed through the GPIO PORTs pins, we need to make sure to request them
so that the muxing is properly set up.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
adev->dma_mode stores the transfer mode value not UDMA mode number
so the condition in cmd64x_set_dmamode() is always true and the higher
UDMA clock is always selected. This can potentially result in data
corruption when UDMA33 device is used, when 40-wire cable is used or
when the error recovery code decides to lower the device speed down.
The issue was introduced in the commit 6a40da0 ("libata cmd64x: whack
into a shape that looks like the documentation") which goes back to
kernel 2.6.20.
Cc: stable@kernel.org
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This reverts commit d43744390e, because
it breaks the boot on several machines (mostly sparc64, at present).
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
sata_mv: remove pointless NULL test
pata_hpt3x2n: fix clock turnaround
libata: fix reporting of drained bytes when clearing DRQ
sata_mv: add power management support for the PCI controllers.
sata_mv: store the board_idx into the host private data
pata_octeon_cf: use resource_size(), to fix resource sizing bug
libata: use the WRITE_SAME_16 define
sata_mv: move the PCI bar description initialization code
sata_mv: add power management support for the platform driver
sata_mv: support clkdev framework
sata_mv: increase PIO IORDY timeout
Fixed crazy mode-change in merge.
Remove !ap test, where ap is guaranteed not-NULL. Found by way of automated
bug report from Alexander Strakh via "Linux Device Drivers Verification
Project (Svace Detector)"
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The clock turnaround code still doesn't work for several reasons:
- 'USE_DPLL' flag in 'ap->host->private_data' is never initialized
or updated, so the driver can only set the chip to the DPLL clock
mode, not the PCI mode;
- the driver doesn't serialize access to the channels depending on
the current clock mode like the vendor drivers, so the clock
turnaround is only executed "optionally", not always as it should be;
- the wrong ports are written to when hpt3x2n_set_clock() is called
for the secondary channel;
- hpt3x2n_set_clock() can inadvertently enable the disabled channels
when resetting the channel state machines.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When we drain data from a device to clear DRQ during error recovery,
the number of bytes reported as drained is too low by a factor of 2
because the count is actually reporting the number of words drained,
not bytes. Fix this.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
It appears the size for cs1 is calculated using the wrong resource.
Use the function resource_size to get the correct value.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now that the scsi tree has hit mainline we can use the newly added WRITE_SAME_16
define.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The mv_init_host will be used to initialize the host hw on resume.
The PCI bar description need to be initialized only once when the
device probed.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The old value (0xbc) in cycles of the IORDY timeout is suitable for
devices with core clock of 166 MHz, but some SoC controllers have
faster core clocks. The new value will make the IORDY timeout large
enough also for all SoC devices.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (151 commits)
powerpc: Fix usage of 64-bit instruction in 32-bit altivec code
MAINTAINERS: Add PowerPC patterns
powerpc/pseries: Track previous CPPR values to correctly EOI interrupts
powerpc/pseries: Correct pseries/dlpar.c build break without CONFIG_SMP
powerpc: Make "intspec" pointers in irq_host->xlate() const
powerpc/8xx: DTLB Miss cleanup
powerpc/8xx: Remove DIRTY pte handling in DTLB Error.
powerpc/8xx: Start using dcbX instructions in various copy routines
powerpc/8xx: Restore _PAGE_WRITETHRU
powerpc/8xx: Add missing Guarded setting in DTLB Error.
powerpc/8xx: Fixup DAR from buggy dcbX instructions.
powerpc/8xx: Tag DAR with 0x00f0 to catch buggy instructions.
powerpc/8xx: Update TLB asm so it behaves as linux mm expects.
powerpc/8xx: Invalidate non present TLBs
powerpc/pseries: Serialize cpu hotplug operations during deactivate Vs deallocate
pseries/pseries: Add code to online/offline CPUs of a DLPAR node
powerpc: stop_this_cpu: remove the cpu from the online map.
powerpc/pseries: Add kernel based CPU DLPAR handling
sysfs/cpu: Add probe/release files
powerpc/pseries: Kernel DLPAR Infrastructure
...
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (222 commits)
[SCSI] zfcp: Remove flag ZFCP_STATUS_FSFREQ_TMFUNCNOTSUPP
[SCSI] zfcp: Activate fc4s attributes for zfcp in FC transport class
[SCSI] zfcp: Block scsi_eh thread for rport state BLOCKED
[SCSI] zfcp: Update FSF error reporting
[SCSI] zfcp: Improve ELS ADISC handling
[SCSI] zfcp: Simplify handling of ct and els requests
[SCSI] zfcp: Remove ZFCP_DID_MASK
[SCSI] zfcp: Move WKA port to zfcp FC code
[SCSI] zfcp: Use common code definitions for FC CT structs
[SCSI] zfcp: Use common code definitions for FC ELS structs
[SCSI] zfcp: Update FCP protocol related code
[SCSI] zfcp: Dont fail SCSI commands when transitioning to blocked fc_rport
[SCSI] zfcp: Assign scheduled work to driver queue
[SCSI] zfcp: Remove STATUS_COMMON_REMOVE flag as it is not required anymore
[SCSI] zfcp: Implement module unloading
[SCSI] zfcp: Merge trace code for fsf requests in one function
[SCSI] zfcp: Access ports and units with container_of in sysfs code
[SCSI] zfcp: Remove suspend callback
[SCSI] zfcp: Remove global config_mutex
[SCSI] zfcp: Replace local reference counting with common kref
...
This is a libata driver for the "macio" IDE controller used on most Apple
PowerMac and PowerBooks. It's a libata equivalent of drivers/ide/ppc/pmac.c
It supports all the features of its predecessor, including mediabay hotplug
and suspend/resume. It should also support module load/unload.
The timing calculations have been simplified to use pre-calculated tables
compared to drivers/ide/pmac.c and it uses the new mediabay interface
provided by a previous patch.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Tejun Heo <tj@kernel.org>
In libata-sff, ata_sff_post_internal_cmd() directly calls ata_bmdma_stop()
instead of ap->ops->bmdma_stop(). This can be a problem for controllers
that use their own bmdma_stop for which the generic sff one isn't suitable
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (54 commits)
Revert "pata_sis: Implement MWDMA for the UDMA 133 capable chips"
libata: Clarify ata_set_lba_range_entries function
libata: Report zeroed read after TRIM and max discard size
pata_hpt3x2n: fix overclocked MWDMA0 timing
pata_it8213: MWDMA0 is unsupported
[libata] MWDMA0 is unsupported on PIIX-like PATA controllers
pata_via: clear UDMA transfer mode bit for PIO and MWDMA
pata_sis: Power Management fix
pata_rz1000: Power Management fix
pata_radisys: fix UDMA handling
pata_ns87415: Power Management fix
pata_marvell: fix marvell_pre_reset() documentation
pata_legacy: add pointers to QDI65x0 documentation
pata_legacy: fix access to control register for QDI6580
pata_legacy: fix QDI6580DP support
pata_it8213: fix it8213_pre_reset() documentation
pata_it8213: fix wrong MWDMA timings being programmed
pata_it8213: fix PIO2 underclocking
pata_it8213: fix wrong PIO timings being programmed
pata_it8213: fix UDMA handling
...
This reverts commit f20941f334.
Sergei Shtylyov notes "You call min() on uncomparables [in
mwdma_clip_to_pio()], i.e. mwdma_to_pio[] contains XFER_PIO_* and
adev->pio_mode - XFER_PIO_0 yields you a mode number. Thus the second
argument will always "win" as a minimal one"
Bartlomiej Zolnierkiewicz adds "There are more issues with the patch related
to mwdma_clip_to_pio(). The function can return values between 0 and
4 which obviously won't work well for the new code below for values
>2 (i.e. resulting in out-of-bounds array access for the common-case
of dev->pio_mode == XFER_PIO_4)."
Bartlomiej Zolnierkiewicz also notes the patch is incomplete, failing to
update MWDMA mode masks.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch modifies scsi_host_template->change_queue_depth so that
it takes an argument indicating why it is being called. This will be
used so that if a LLD needs to do some extra processing when
handling queue fulls or later ramp ups, it can do so.
This is a simple port of the drivers setting a change_queue_depth
callback. In the patch I just have these LLDs adjust the queue depth
if the user was requesting it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
[Vasu.Dev: v2
Also converted pmcraid_change_queue_depth and then verified
all modules compile using "make allmodconfig" for any new build
warnings on X86_64.
Updated original description after combing two original
patches from Mike to make this patch git bisectable.]
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
[jejb: fixed up 53c700]
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
ata_set_lba_range_entries used the variable max for two different things
which was confusing. Make the function take a buffer size in bytes as
argument and return the used buffer size upon completion.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Our current TRIM payload is a single sector that can accommodate 64 *
65535 blocks being unmapped. Report this value in the Block Limits
Maximum Unmap LBA count field.
If a storage device supports TRIM and the DRAT and RZAT bits are set,
report TPRZ=1 in Read Capacity(16).
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove superfluous timings table entry while at it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
MWDMA0 timings cannot be met with the PIIX based controller
programming interface.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Set correct bits to switch between UDMA2 and UDMA4.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix ->resume method to do chipset specific setup.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We need to mask out the port offset from the port number
cached in ld_qdi->timing.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Dual port QDI6580 has shared PIO timings for master/slave
devices so it needs to use custom ->qc_issue method.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>