- Made changes to support IO profiling.
- Added support to configure and query IO profiling info.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Extended BSG to support stats, port log and trace reset and to support
adapter, port SET operations.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Added logic to check the loopback test input speed based on port mode.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Made changes to always acknowledge RME interrupt and update
consumer index (CI) when RME interrupt is generated.
- Made changes to have ASIC specific hw_rspq_ack() handler.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Added support to post vendor unique events on fc_host.
- Supports adapter, port, ioc, flash and remote port based AEN events.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
rdac hardware handler uses "Subsystem Identifier" from C4 inquiry page
to uniquely identify a storage. The problem with that is that if any
any of the bytes are non-ascii, subsys_id will all be spaces (hex
0x20). This creates lot of problems especially when there are multiple
rdac storages are connected to the server.
Use "Storage Array Unique Identifier" from C8 inquiry page, which is the
world wide unique identifier for the storage array, to uniquely identify
the storage.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When READ_6 command is issued, the setting of SILI Bit in CDB is confirmed and
if SILI bit is off, the processing of relavent Errata is executed.
Earlier we did not have check for SILI bit in READ_6 CDB.
As described in "ssc-r22", Now Driver is checking SILI bit for READ_6.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The code is changed to support the new dynamic logging infrastructure.
Following are the levels added.
Default is 0 - no logging. 0x40000000 - Module Init & Probe.
0x20000000 - Mailbox Cmnds. 0x10000000 - Device Discovery.
0x08000000 - IO tracing. 0x04000000 - DPC Thread.
0x02000000 - Async events. 0x01000000 - Timer routines.
0x00800000 - User space. 0x00400000 - Task Management.
0x00200000 - AER/EEH. 0x00100000 - Multi Q.
0x00080000 - P3P Specific. 0x00040000 - Virtual Port.
0x00020000 - Buffer Dump. 0x00010000 - Misc.
0x7fffffff - For enabling all logs, can be too many logs.
Setting ql2xextended_error_logging module parameter to any of the above
value, will enable the debug for that particular level.
Do LOGICAL OR of the value to enable more than one level.
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds the dynamic logging framework to the qla2xxx driver.
The user will be able to change the logging levels on the fly i.e.
without load/unload of the driver. This also enables logging to be
enabled for a particular section of the driver such as initialization,
device discovery etc.
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
During cable pull tests on our 16G FC adapter, we are seeing errors,
typically reads to close targets, which fail due to CRC or framing
errors caused by the cable being pull (return status DID_ERROR).
The adapter detects the error on one of the first frames received,
marks the FC exchange as dead (further frames go to bit bucket) and
signals the host of the error. This action is so quick, and coupled
with fast host CPUs, creates a scenario in which the midlayer sees
the failure and retries the io almost immediately. We've seen link
traces with the retry on the link while the original i/o is still
being processed by the target. We're also seeing the time window
for the "link to pull-apart" and the physical interface to report
disconnected to be in the few millisecond range. Which means, we're
encountering scenarios where the full retry count is exhausted
(all with error) by the midlayer before the link disconnect state
is detected.
We looked at 8G FC behavior and occasionally see the same behavior,
but as the link was slower, it rarely could exhaust all retries
before the link reported disconnect.
What is needed is a slight delay between io retries due to DID_ERROR
to cover this error. It is inappropriate to put this delay in the
driver, as the error is indistinguishable from other link-related errors,
nor does the driver track whether the io is a retry or not. This is also
easier than tracking between-io-error bursts that are seen in this
scenario.
The patch below updates the retry path so that it inserts a delay as
if the target was busy. The busy delay is on the order of 6ms. This
delay is sufficient to ensure the link down condition is reported
before the retry count is exhausted (at most 1 retry is seen).
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
This issue is seen on LSI H/W WarpDrive SSS6200 When filed direct I/O
is tried as volume I/O the scmd field in internal lookup table get
cleared and because of that the retried volume I/O never gets reported
as completed to SML.
Result:
I/O timeout and Error handling thread will kicking off
Fix:
Setting back the scmd in the lookup table before retrying the failed
direct i/o
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Currently it's impossible to find out if the host supports
wide SCSI unless you're committed to trawl through syslog.
And it's near impossible to find the actual HBA id, which
is settable for some SCSI HBAs (like aic7xxx).
So export them via sysfs.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Ankit Jain <jankit@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add support for interrupt tasklet, which will improve performance.
Correct spelling of "20011"
[jejb: simplified ifdefs and fixed unused variable problem]
Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Remove obsolete comments and add new comments
Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Change code to match HBA datasheet.
Change code to make it readable.
Add support big endian for mvs_prd_imt.
Add cpu_to_le32 and cpu_to_le64 to use on addr.
Add scan_finished for structure mvs_prv_info.
Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add new macros: MVS_SOFT_RESET, MVS_HARD_RESET, MVS_PHY_TUNE,
MVS_COMMAND_ACTIVE, EXP_BRCT_CHG, MVS_MAX_SG
Add new member sg_width in struct mvs_chip_info
Use macros rather than magic number
Add new functions: mvs_fill_ssp_resp_iu, mvs_set_sense,
mvs_94xx_clear_srs_irq, mvs_94xx_phy_set_link_rate
Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* Merge akpm patch series: (122 commits)
drivers/connector/cn_proc.c: remove unused local
Documentation/SubmitChecklist: add RCU debug config options
reiserfs: use hweight_long()
reiserfs: use proper little-endian bitops
pnpacpi: register disabled resources
drivers/rtc/rtc-tegra.c: properly initialize spinlock
drivers/rtc/rtc-twl.c: check return value of twl_rtc_write_u8() in twl_rtc_set_time()
drivers/rtc: add support for Qualcomm PMIC8xxx RTC
drivers/rtc/rtc-s3c.c: support clock gating
drivers/rtc/rtc-mpc5121.c: add support for RTC on MPC5200
init: skip calibration delay if previously done
misc/eeprom: add eeprom access driver for digsy_mtc board
misc/eeprom: add driver for microwire 93xx46 EEPROMs
checkpatch.pl: update $logFunctions
checkpatch: make utf-8 test --strict
checkpatch.pl: add ability to ignore various messages
checkpatch: add a "prefer __aligned" check
checkpatch: validate signature styles and To: and Cc: lines
checkpatch: add __rcu as a sparse modifier
checkpatch: suggest using min_t or max_t
...
Did this as a merge because of (trivial) conflicts in
- Documentation/feature-removal-schedule.txt
- arch/xtensa/include/asm/uaccess.h
that were just easier to fix up in the merge than in the patch series.
Fix the warning
drivers/connector/cn_proc.c: In function 'proc_ptrace_connector':
drivers/connector/cn_proc.c:176: warning: unused variable 'tracer'
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There have been persistent lockdep RCU splats, indicating that submitters
are not testing with CONFIG_PROVE_RCU. Add this config option to the list
in Documentation/SubmitChecklist. Also add CONFIG_DEBUG_OBJECTS_RCU_HEAD
for good measure.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use hweight_long() to count free bits in the bitmap.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Using __test_and_{set,clear}_bit_le() with ignoring its return value can
be replaced with __{set,clear}_bit_le().
This introduces reiserfs_{set,clear}_le_bit for __{set,clear}_bit_le and
does the above change with them.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When parsing PnP ACPI resource structures, it may happen that some of
the resources are disabled (in which case "the size" of the resource
equals zero).
The current solution is to skip these resources completely - with the
unfortunate side effect that they are not registered despite the fact
that they exist, after all. (The downside of this approach is that
these resources cannot be used as templates for setting the actual
device's resources because they are missing from the template.) The
kernel's APM implementation does not suffer from this problem and
registers all resources regardless of "their size".
This patch fixes a problem with (at least) the vintage IBM ThinkPad 600E
(and most likely also with the 600, 600X, and 770X which have a very
similar layout) where some of its PnP devices support options where
either an IRQ, a DMA, or an IO port is disabled. Without this patch,
the devices can not be configured using the
"/sys/bus/pnp/devices/*/resources" interface.
The manipulation of these resources is important because the 600E has
very demanding requirements. For instance, the number of IRQs is not
sufficient to support all devices of the 600E. Fortunately, some of the
devices, like the sound card's MPU-401 UART, can be configured to not
use any IRQ, hence freeing an IRQ for a device that requires one.
(Still, the device's "ResourceTemplate" requires an IRQ resource
descriptor which cannot be created if the resource has not been
registered in the first place.)
As an example, the dependent sets of the 600E's CSC0103 device (the
MPU-401 UART) are listed, with the patch applied, as:
Dependent: 00 - Priority preferred
port 0x300-0x330, align 0xf, size 0x4, 16-bit address decoding
irq <none> High-Edge
Dependent: 01 - Priority acceptable
port 0x300-0x330, align 0xf, size 0x4, 16-bit address decoding
irq 5,7,2/9,10,11,15 High-Edge
(The same result is obtained when PNPBIOS is used instead of PnP ACPI.)
Without the patch, the IRQ resource in the preferred option is not
listed at all:
Dependent: 00 - Priority preferred
port 0x300-0x330, align 0xf, size 0x4, 16-bit address decoding
Dependent: 01 - Priority acceptable
port 0x300-0x330, align 0xf, size 0x4, 16-bit address decoding
irq 5,7,2/9,10,11,15 High-Edge
And in fact, the 600E's DSDT lists the disabled IRQ as an option, as can
be seen from the following excerpt from the DSDT:
Name (_PRS, ResourceTemplate ()
{
StartDependentFn (0x00, 0x00)
{
IO (Decode16, 0x0300, 0x0330, 0x10, 0x04)
IRQNoFlags () {}
}
StartDependentFn (0x01, 0x00)
{
IO (Decode16, 0x0300, 0x0330, 0x10, 0x04)
IRQNoFlags () {5,7,9,10,11,15}
}
EndDependentFn ()
})
With this patch applied, a user space program - or maybe even the kernel
- can allocate all devices' resources optimally. For the 600E, this
means to find optimal resources for (at least) the serial port, the
parallel port, the infrared port, the MWAVE modem, the sound card, and
the MPU-401 UART.
The patch applies the idea to register disabled resources to all types
of resources, not just to IRQs, DMAs, and IO ports. At the same time,
it mimics the behavior of the "pnp_assign_xxx" functions from
"drivers/pnp/manager.c" where resources with "no size" are considered
disabled.
No regressions were observed on hardware that does not require this
patch.
The patch is applied against 2.6.39.
NB: The kernel's current PnP interface does not allow for disabling individual
resources using the "/sys/bus/pnp/devices/$device/resources" file. Assuming
this could be done, a device could be configured to use a disabled resource
using a simple series of calls:
echo disable > /sys/bus/pnp/devices/$device/resources
echo clear > /sys/bus/pnp/devices/$device/resources
echo set irq disabled > /sys/bus/pnp/devices/$device/resources
echo fill > /sys/bus/pnp/devices/$device/resources
echo activate > /sys/bus/pnp/devices/$device/resources
This patch addresses only the parsing of PnP ACPI devices.
ChangeLog (v1 -> v2):
- extend patch description
- fix typo in patch itself
Signed-off-by: Witold Szczeponik <Witold.Szczeponik@gmx.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Adam Belay <abelay@mit.edu>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Using __SPIN_LOCK_UNLOCKED for a dynamically allocated lock is wrong and
breaks the build with PREEMPT_RT_FULL.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Andrew Chew <achew@nvidia.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We forget to save the return value of the call to
twl_rtc_write_u8(save_control, REG_RTC_CTRL_REG); in 'ret', making the
test of 'ret < 0' dead code since 'ret' then couldn't possibly have
changed since the last test just a few lines above. It also makes us not
detect failures from that specific twl_rtc_write_u8() call.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Rusev <source@mvista.com>
Cc: "George G. Davis" <gdavis@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for PMIC8xxx based RTC. PMIC8xxx is Qualcomm's power
management IC that internally houses an RTC module. This driver
communicates with the PMIC module over SSBI bus.
[akpm@linux-foundation.org: cosmetic tweaks]
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Anirudh Ghayal <aghayal@codeaurora.org>
Signed-off-by: Ashay Jaiswal <ashayj@codeaurora.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for clock gating. Power consumption can be reduced by setting
rtc_clk disabled state except for when RTC related registers are accessed.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: KyungMin Park <kyungmin.park@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Ben Dooks <ben@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
MPC5200B contains a limited version of RTC from MPC5121. Add support for
the RTC on that CPU.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For each CPU, do the calibration delay only once. For subsequent calls,
use the cached per-CPU value of loops_per_jiffy.
This saves about 200ms of resume time on dual core Intel Atom N5xx based
systems. This helps bring down the kernel resume time on such systems
from about 500ms to about 300ms.
[akpm@linux-foundation.org: make cpu_loops_per_jiffy static]
[akpm@linux-foundation.org: clean up message text]
[akpm@linux-foundation.org: fix things up after upstream rmk changes]
Signed-off-by: Sameer Nanda <snanda@chromium.org>
Cc: Phil Carmody <ext-phil.2.carmody@nokia.com>
Cc: Andrew Worsley <amworsley@gmail.com>
Cc: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Both displays on digsy_mtc board obtain their configuration from microwire
EEPROMs which are connected to the SoC over GPIO lines. We need an easy
way to access the EEPROMs to write the needed display configuration or to
read out the currently programmed configuration. The generic
eeprom_93xx46 SPI driver added by previous patch allows EEPROM access over
sysfs. Using the simple driver added by this patch we provide used GPIO
interface and access control description on the board for generic
eeprom_93xx46 driver and spi_gpio driver.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add EEPROM driver for 93xx46 chips. It can also be used with spi_gpio
driver to access 93xx46 EEPROMs connected over GPIO lines. This driver
supports read/write/erase access to the EEPROM chips over sysfs files.
[rdunlap@xenotime.net: fix printk format]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Previous behavior allowed only alphabetic prefixes like pr_info to exceed
the 80 column line length limit.
ath6kl wants to add a digit into the prefix, so allow numbers as well as
digits in the <prefix>_<level> printks.
<prefix>_<level>_ratelimited and <prefix>_<level>_once and WARN_RATELIMIT
and WARN_ONCE may now exceed 80 cols.
Add missing <prefix>_printk type for completeness.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Andy Whitcroft <apw@canonical.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some patches are sent in using ISO-8859 or even Windows codepage 1252.
Make checkpatch accept these by default and only emit the "Invalid UTF-8"
message when using --strict.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some users would like the ability to not emit some of the messages that
checkpatch produces. This can make it easier to use checkpatch in other
projects and integrate into scm hook scripts.
Add command line option to "--ignore" various message types. Add option
--show-types to emit the "type" of each message. Categorize all ERROR,
WARN and CHK messages with types.
Add optional .checkpatch.conf file to store default options.
3 paths are searched for .checkpatch.conf
. customized per-tree configurations
$HOME user global configuration when per-tree configs don't exist
./scripts lk defaults to override script
The .conf file can contain any valid command-line argument and
the contents are prepended to any additional command line arguments.
Multiple lines may be used, blank lines are ignored, # is a comment.
Update "false positive" output for readability.
Update version to 0.32
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Cc: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prefer the use of __aligned(size) over __attribute__((__aligned___(size)))
Link: http://lkml.kernel.org/r/20110609094526.1571774c.akpm@linux-foundation.org
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signatures have many forms and can sometimes cause problems if not in the
correct format when using git send-email or quilt.
Try to verify the signature tags and email addresses to use the generally
accepted "Signed-off-by: Full Name <email@domain.tld>" form.
Original idea by Anish Kumar <anish198519851985@gmail.com>
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Anish Kumar <anish198519851985@gmail.com>
Cc: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix "need consistent spacing around '*'" error after a __rcu sparse
annotation which was caused by the missing __rcu entry in the
checkpatch.pl internal list of sparse keywords.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Cc: Andy Whitcroft <apw@canonical.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A common issue with min() or max() is using a cast on one or both of the
arguments when using min_t/max_t could be better.
Add cast detection to uses of min/max and suggest an appropriate use of
min_t or max_t instead.
Caveat: This only works for min() or max() on a single line.
It does not find min() or max() split across multiple lines.
This does find:
min((u32)foo, bar);
But it does not find:
max((unsigned long)foo,
bar);
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This function is required by *printf and kstrto* functions that are
located in the different modules. This patch makes _tolower() public.
However, it's good idea to not use the helper outside of mentioned
functions.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The symbol 'lcm' is exported to the kernel (EXPORT_SYMBOL_GPL).
Pick up it's definition in <linux/lcm.h> to quiet the sparse noise:
warning: symbol 'lcm' was not declared. Should it be static?
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
From: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
platform data for simple backlight driver for LM3530
in the u5500 platform
Signed-off-by: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Provide the support for auto calibration of ALS Zone boundaries based on
min/max ALS input voltage.
Signed-off-by: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
