This enables support of 'input-enable' pinconf generic property in
the pinctrl driver.
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the pinctrl driver to use the generic pinconf
interface. Mainly it gives us a way to use debugfs to dump
group configurations.
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no code ender the 'err' label. Just return the error code directly.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tegra210's pinmux supports a different set of pins/options than earlier
SoCs, so requires its own driver (well, table of pin-specific data).
Cc: devicetree@vger.kernel.org
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Both nvidia,io-hv and nvidia,rcv-sel represent the fact that a particular
pin's IO buffers are configured to accept "high voltage" input signals.
The TRM for different chips names the register field rcv-sel on older
SoCs and io_hv on newer SoCs. Add the new naming option into the pinctrl
driver so that DT files can use naming consistent with the TRM.
This new property name will be documented in the patch that adds support
for the new SoC.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some of the pinmux configuration bits that exist in "drive group"
registers in Tegra30..Tegra124 move to the "pinmux" registers on future
chips. Add a flag to support this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Various non-semantic tweaks and layout/consistency fixes for existing
Tegra pinctrl drivers.
Move the definition of DRV_PINGROUP_REG() before the definition of
PINGROUP() so that a future SoC driver can invoke the former from the
latter.
PINGROUP_BIT_Y(n) is just n, so replace it with n.
Re-wrap the parameters to *PINGROUP().
Keep various enums sorted in the Tegra124 driver.
Various white-space consistency fixes.
These changes aim to update existing drivers to be consistent with future
SoC drivers. While we could ignore these tweaks to the existing drivers,
I'd like to keep everything as consistent as possible for easy comparison.
Besides, I auto-generate the drivers, and maintaining special-cases to
keep the differences in place is annoying.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After the last user of the in_pd/in_pu bias parameters of the _PCRH()
macro was removed in commit 80da8e02d2 ("sh-pfc: r8a7740: Add bias
(pull-up/down) pinconf support"), bias parameters are supposed to be
configured using the generic pinctl mechanism, which calls the
.set_bias() method.
However, the PORTCR() macro still represents the control register as
consisting of two 4-bit fields. Hence the bias configuration in the
uppermost 2 bits is always overwritten with zeroes when a pin is
configured for GPIO, disabling any previously configured bias.
Use the variable config register macro instead, to represent the
register as having 4 fields, and to make sure only the input/output
control and function fields are touched.
This affects R-Mobile APE6 (r8a73a4), R-Mobile A1 (r8a7740), SH-Mobile
AP4 (sh7372), and SH-Mobile AG5 (sh73a0).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The r8a7791 platform is now DT-only, the driver doesn't need to match
platform devices by name anymore. Remove the corresponding
platform_device_id entry.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds driver data for Exynos5433 SoC. Exynos5433 includes 228 multi-
functional input/output port pins and 135 memory port pins. There are 41 general
port groups and 2 memory port groups.
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit adds a new pinctrl driver for the Marvell Armada 39x
family of processors, which hooks into the existing infrastructure to
support pin-muxing on Marvell EBU processors. Two variants of the
Armada 39x are supported: 88F6920 (Armada 390) and 88F6928 (Armada
398), which have a few differences in the available functions for
certain pins.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Framework changes and enhancements:
- Passing -DDEBUG recursively to subdir drivers so we get
debug messages properly turned on.
- Infer map type from DT property in the groups parsing code
in the generic pinconfig code.
- Support for custom parameter passing in generic pin config.
This is used when you are using the generic pin config, but
want to add a few custom properties that no other driver
will use.
- New drivers:
- Driver for the Xilinx Zynq
- Driver for the AmLogic Meson SoCs
- New features in drivers:
- Sleep support (suspend/resume) for the Cherryview driver
- mvebeu a38x can now mux a UART on pins MPP19 and MPP20
- Migrated the qualcomm driver to generic pin config handling
of extended config options in the core code.
- Support BUS1 and AUDIO in the Exynos pin controller.
- Add some missing functions in the sun6i driver.
- Add support for the A31S variant in the sun6i driver.
- EMEv2 support in the Renesas PFC driver.
- Ass support for Qualcomm MSM8916 in the qcom driver.
- Deleted features
- Drop support for the SiRF Marco that was never released to
the market.
- Drop SH7372 support as the support for this platform is
removed from the kernel.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Nbzh
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v3.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pincontrol updates from Linus Walleij:
:This is the bulk of pin control changes for the v3.20 cycle:
Framework changes and enhancements:
- Passing -DDEBUG recursively to subdir drivers so we get debug
messages properly turned on.
- Infer map type from DT property in the groups parsing code in the
generic pinconfig code.
- Support for custom parameter passing in generic pin config. This
is used when you are using the generic pin config, but want to add
a few custom properties that no other driver will use.
New drivers:
- Driver for the Xilinx Zynq
- Driver for the AmLogic Meson SoCs
New features in drivers:
- Sleep support (suspend/resume) for the Cherryview driver
- mvebeu a38x can now mux a UART on pins MPP19 and MPP20
- Migrated the qualcomm driver to generic pin config handling of
extended config options in the core code.
- Support BUS1 and AUDIO in the Exynos pin controller.
- Add some missing functions in the sun6i driver.
- Add support for the A31S variant in the sun6i driver.
- EMEv2 support in the Renesas PFC driver.
- Add support for Qualcomm MSM8916 in the qcom driver.
Deleted features
- Drop support for the SiRF Marco that was never released to the
market.
- Drop SH7372 support as the support for this platform is removed
from the kernel"
* tag 'pinctrl-v3.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (40 commits)
sh-pfc: emev2 - Fix mangled author name
pinctrl: cherryview: Configure HiZ pins to be input when requested as GPIOs
pinctrl: imx25: fix numbering for pins
pinctrl: pinctrl-imx: don't use invalid value of conf_reg
pinctrl: qcom: delete pin_config_get/set pinconf operations
pinctrl: qcom: Add msm8916 pinctrl driver
DT: pinctrl: Document Qualcomm MSM8916 pinctrl binding
pinctrl: qcom: increase variable size for register offsets
pinctrl: hide PCONFDUMP in #ifdef
pinctrl: rockchip: Only mask interrupts; never disable
pinctrl: zynq: Fix usb0 pins
pinctrl: sh-pfc: sh7372: Remove DT binding documentation
pinctrl: sh-pfc: sh7372: Remove PFC support
sh-pfc: Add emev2 pinmux support
sh-pfc: add macro to define pinmux without function
pinctrl: add driver for Amlogic Meson SoCs
staging: drivers: pinctrl: Fixed checkpatch.pl warnings
pinctrl: exynos: Add AUDIO pin controller for exynos7
sh-pfc: r8a7790: add MLB+ pin group
sh-pfc: r8a7791: add MLB+ pin group
...
If the pin is in HiZ mode when it is requested as GPIO its value cannot be
read (it always returns 0). In order to cope with the Linux GPIO subsystem
where we do not have such state at all, turn the pin to be input instead.
Reported-by: Jerome Blin <jerome.blin@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pin id for a given tuple listed in a fsl,pins property is calculated
by dividing the first entry (which is also a register offset) by 4.
As the first available register is at offset 0x8 and configures the pad
MX25_PAD_A10 the right id for this pin is 2. All other pins are off by
one, too.
This patch drops the definition MX25_PAD_RESERVE1 (together with its
only use) and decrements all following values by 1.
Fixes: b4a87c9b96 ("pinctrl: pinctrl-imx: add imx25 pinctrl driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The right check for conf_reg to be invalid it testing against -1 not 0
as is done in the rest of the driver.
This fixes an oops that can be triggered by:
cat /sys/kernel/debug/pinctrl/43fac000.iomuxc/*
Fixes: ae75ff8145 ("pinctrl: pinctrl-imx: add imx pinctrl core driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The .pin_config_get/set operation are not supported in qcom pinctrl
driver. As the pinconf core is smart enough it doesn't complain
about that.
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On newer TLMM hardware blocks the registers are spread and
we need an offsets upper than 16 bits to address them. Increase
the register offset variables to 32 bits size.
Signed-off-by: Joonwoo Park <joonwoop@codeaurora.org>
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The zynq and qcom-spmi pinctrl drivers both use pin_config_item arrays
to provide extra interfaces in debugfs. This structure and the
PCONFDUMP macro are not defined if CONFIG_DEBUG_FS is turned off,
so we get build errors like:
pinctrl/qcom/pinctrl-spmi-gpio.c:139:37: error: array type has incomplete element type
static const struct pin_config_item pmic_conf_items[ARRAY_SIZE(pmic_gpio_bindings)] = {
^
pinctrl/qcom/pinctrl-spmi-gpio.c:140:2: error: implicit declaration of function 'PCONFDUMP' [-Werror=implicit-function-declaration]
PCONFDUMP(PMIC_GPIO_CONF_PULL_UP, "pull up strength", NULL, true),
^
pinctrl/qcom/pinctrl-spmi-gpio.c:139:37: warning: 'pmic_conf_items' defined but not used [-Wunused-variable]
static const struct pin_config_item pmic_conf_items[ARRAY_SIZE(pmic_gpio_bindings)] = {
Lacking any better idea to solve this nicely, this patch uses #ifdef
to hide the structures, just like the pinctrl core does.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Rockchip GPIO interrupt controller totally throws away all status
about an interrupt when you "disable" the interrupt. That has
unfortunate consequences in the following situation:
1. An edge-triggered interrupt is enabled and should wake the system.
2. System suspend happens: interrupt is disabled and marked for wake.
3. rockchip_irq_suspend() reenables the interrupt so we can wake.
4. Interrupt happens when asleep.
5. rockchip_irq_resume() redisables the interrupt.
6. Disabling the interrupt throws away all status about it.
7. Normal system resume happens and we enable the interrupt again,
since we threw away status about the interrupt we don't know it
fired while suspended. Even worse: if we need both edges of the
interrupt the logic to swap edges never runs.
Note: even if we somehow can post the status about wakeup interrupts
in rockchip_irq_resume() we would still have a window of losing any
edges that came in while interrupts were disabled.
If we use mask only then we don't need to worry. The GPIO Interrupt
controller keeps track of pending interrupts that are enabled and just
masked.
There was no real strong reason to support the enable/disable
functionality (other than that it seemed right), so let's go back to
just supporting mask/unmask but actually map it to the real
mask/unmask. This ends up with slightly different (and more correct)
behavior than before (f2dd028 pinctrl: rockchip: Fix
enable/disable/mask/unmask).
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix usb0 pin 19 -> 29 (matching ethernet1 pins and manual).
Pin 19 is used for ethernet0 on the Parallella board.
Fixes: add958cee9 ("pinctrl: Add driver for Zynq")
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove sh7372 PFC support as part of the sh7372 and Mackerel
legacy code removal.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add PFC support for the EMMA Mobile EV2 SoC including pin groups for
on-chip devices.
Signed-off-by: Niklas Söderlund <niso@kth.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Used to define pinmux configurations where the pinmux function have no
representation in the configuration registers but instead solely depends
on a group selection.
Signed-off-by: Niklas Söderlund <niso@kth.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Today we expect that all the bank are enabled, and count the number of banks
used by the pinctrl based on it instead of using the last bank id enabled.
So switch to it, set the chained IRQ at runtime based on enabled banks
and wait only the number of enabled gpio controllers at probe time.
Cc: <stable@vger.kernel.org> # 3.18
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a driver for the pinmux and GPIO controller available in
Amlogic Meson SoCs. It currently supports only Meson8, however the
common code should be generic enough to work also for other SoCs after
having defined the proper set of functions and groups.
GPIO interrupts are not supported at the moment due to lack of
documentation.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fixes two checkpatch.pl warnings
WARNING: Error trailing white space
WARNING: MIssing blank line after declaration
Signed-off-by: Anjana Sasindran <anjanasasindran123@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Timur reports that this code crashes if nfunctions is 0. Fix the
loop iteration to only consider valid elements of the functions
array.
Reported-by: Timur Tabi <timur@codeaurora.org>
Cc: Pramod Gurav <pramod.gurav@smartplayin.com>
Cc: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Cc: Ivan T. Ivanov <iivanov@mm-sol.com>
Cc: Andy Gross <agross@codeaurora.org>
Fixes: 327455817a "pinctrl: qcom: Add support for reset for apq8064"
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Audio IPs on Exynos7 require gpios available in AUDIO
pin controller block. So adding the AUDIO pinctrl support.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add MLB+ 3-pin mode pin group to R8A7790 PFC driver.
Based on original patch by Andrey Gusakov <andrey.gusakov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add MLB+ 3-pin mode pin group to R8A7791 PFC driver.
Based on original patch by Andrey Gusakov <andrey.gusakov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The R8A7791 manual sometimes calls the signal MLB_CLK and sometimes MLB_CK; the
latter can only be encountered in the PFC section and is probably just a typo
(this signal is always called MLB_CLK in the R8A7790 manual). Fix occurences
of MLB_CK throughout the R8A7791 PFC driver.
Based on original patch by Andrey Gusakov <andrey.gusakov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
marco chip has been dropped, clear its support.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const. Make also
of_device_id array const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const. Make also
of_device_id array const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The A31s is a stripped down version of the A31, as such it is missing some
pins and some functions on some pins.
The new pinctrl-sun6i-a31s.c this commit adds is a copy of pinctrl-sun6i-a31s.c
with the missing pins and functions removed.
Note there is no a31s specific version of pinctrl-sun6i-a31-r.c, as the
prcm pins are identical between the A31 and the A31s.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
While working on pinctrl for the A31s, I noticed that function 4 of
PA15 - PA18 was missing, add these.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
USB and Power regulator on Exynos7 require gpios available
in BUS1 pin controller block.
So adding the BUS1 pinctrl support.
Signed-off-by: Naveen Krishna Ch <naveenkrishna.ch@gmail.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
New pin controllers such as ACPI-based may also have custom properties
to parse, and should be able to use generic pin config. Let's make the
code compile on !OF systems and rename members a bit to underscore it
is custom parameters and not necessarily DT parameters.
This fixes a build regression for x86_64 on the zeroday kernel builds.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reviewed-and-tested-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove bogus call to of_gpiochip_add (and of_gpio_chip remove in error
path) which is also called when adding the gpio chip.
This prevents adding the same pinctrl range twice.
Fixes: 3f8c50c9b1 ("OF: pinctrl: MIPS: lantiq: implement lantiq/xway
pinctrl support")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch is to fix two deadlock cases.
Deadlock 1:
CPU #1
pinctrl_register-> pinctrl_get ->
create_pinctrl
(Holding lock pinctrl_maps_mutex)
-> get_pinctrl_dev_from_devname
(Trying to acquire lock pinctrldev_list_mutex)
CPU #0
pinctrl_unregister
(Holding lock pinctrldev_list_mutex)
-> pinctrl_put ->> pinctrl_free ->
pinctrl_dt_free_maps -> pinctrl_unregister_map
(Trying to acquire lock pinctrl_maps_mutex)
Simply to say
CPU#1 is holding lock A and trying to acquire lock B,
CPU#0 is holding lock B and trying to acquire lock A.
Deadlock 2:
CPU #3
pinctrl_register-> pinctrl_get ->
create_pinctrl
(Holding lock pinctrl_maps_mutex)
-> get_pinctrl_dev_from_devname
(Trying to acquire lock pinctrldev_list_mutex)
CPU #2
pinctrl_unregister
(Holding lock pctldev->mutex)
-> pinctrl_put ->> pinctrl_free ->
pinctrl_dt_free_maps -> pinctrl_unregister_map
(Trying to acquire lock pinctrl_maps_mutex)
CPU #0
tegra_gpio_request
(Holding lock pinctrldev_list_mutex)
-> pinctrl_get_device_gpio_range
(Trying to acquire lock pctldev->mutex)
Simply to say
CPU#3 is holding lock A and trying to acquire lock D,
CPU#2 is holding lock B and trying to acquire lock A,
CPU#0 is holding lock D and trying to acquire lock B.
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
I was seeing cases where I was losing interrupts when inserting and
removing SD cards. Sometimes the card would get "stuck" in the
inserted state.
I believe that the problem was related to the code to handle the case
where we needed both rising and falling edges. This code would
disable the interrupt as the polarity was switched. If an interrupt
came at the wrong time it could be lost.
We'll match what the gpio-dwapb.c driver does upstream and change the
interrupt polarity without disabling things.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of the driver caring about implementation details like device
tree, just provide information about driver specific pinconf parameters
to pinconf-generic which takes care of parsing the DT.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a pin-control driver for Zynq.
Changes since v2:
- driver-specific DT properties are passed to the core in two arrays,
one for the actual DT parsing one for the debugfs representation.
Issue a compiler warning when the number of entries is not the same
for both arrays.
Changes since v1:
- fix EMIO_SD1_CD pin name
- add USB to pinmux options
changes since RFCv2:
- let Zynq select PINCTRL_ZYNQ. Boot hangs when pinctrl information is
present in DT but no driver available.
- add #defines to get rid of magical constants
- add commas at end of initializers
- separate changes in mach-zynq in separate patch
- add driver specific io-standard DT property
- refactored pinconf set function to not require arguments for
argument-less properties
- squash other patches in
- support for IO-standard property
- support for low-power mode property
- migration to pinconf_generic_dt_node_to_map_all()
- use newly created infrastructure to add pass driver-specific DT
params to pinconf-generic
changes since RFC:
- use syscon/regmap to access registers in SLCR space
- rebase to 3.18: rename enable -> set_mux
- add kernel-doc
- support pinconf
- supported attributes
- pin-bias: pull up, tristate, disable
- slew-rate: 0 == slow, 1 == fast; generic pinconf does not display
argument
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Additionally to the generic DT parameters, allow drivers to provide
driver-specific DT parameters to be used with the generic parser
infrastructure.
To achieve this 'struct pinctrl_desc' is extended to pass custom pinconf
option to the core. In order to pass this kind of information, the
related data structures - 'struct pinconf_generic_dt_params',
'pin_config_item' - are moved from pinconf internals to the
pinconf-generic header.
Additionally pinconfg-generic is refactored to not only iterate over the
generic pinconf parameters but also take the parameters into account
that are provided through the driver's 'struct pinctrl_desc'.
In particular 'pinconf_generic_parse_dt_config()' and
'pinconf_generic_dump' helpers are split into two parts each. In order
to have a more generic helper that can be used to process the generic
parameters as well as the driver-specific ones.
v2:
- fix typo
- add missing documentation for @conf_items member in struct
- rebase to pinctrl/devel: conflict in abx500
- rename _pinconf_generic_dump() to pinconf_generic_dump_one()
- removed '_' from _parse_dt_cfg()
- removed BUG_ONs, error condition is handled in if statements
- removed pinconf_generic_dump_group() & pinconf_generic_dump_pin
helpers
- fixed up corresponding call sites
- renamed pinconf_generic_dump() to pinconf_generic_dump_pins()
- added kernel-doc to pinconf_generic_dump_pins()
- add kernel-doc
- more verbose commit message
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
