Fix up booting with sparse mem enabled. Otherwise it would just
cause an early PANIC at boot.
Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is needed for large multinode IBM systems which have a sparse
APIC space in clustered mode, fully covering the available 8 bits.
The previous kernels would limit the local APIC number to 127,
which caused it to reject some of the CPUs at boot.
I increased the maximum and shrunk the apic_version array a bit
to make up for that (the version is only 8 bit, so don't need
an full int to store)
Cc: Chris McDermott <lcm@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CONFIG_CHECKING covered some debugging code used in the early times
of the port. But it wasn't even SMP safe for quite some time
and the bugs it checked for seem to be gone.
This patch removes all the code to verify GS at kernel entry. There
haven't been any new bugs in this area for a long time.
Previously it also covered the sysctl for the page fault tracing.
That didn't make much sense because that code was unconditionally
compiled in. I made that a boot option now because it is typically
only useful at boot.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The current x86_64 NUMA memory code is inconsequent when it comes to node
memory ranges. The exact behaviour varies depending on which config option
that is used.
setup_node_bootmem() has start and end as arguments and these are used to
calculate the size of the node like this: (end - start). This is all fine
if end is pointing to the first non-available byte. The problem is that the
current x86_64 code sometimes treats it as the last present byte and sometimes
as the first non-available byte. The result is that some configurations might
lose a page at the end of the range.
This patch tries to fix CONFIG_ACPI_NUMA, CONFIG_K8_NUMA and CONFIG_NUMA_EMU
so they all treat the end variable as the first non-available byte. This is
the same way as the single node code.
The patch is boot tested on dual x86_64 hardware with the above configurations,
but maybe the removed code is needed as some workaround?
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The logging for boot errors was turned off because it was broken
on some AMD systems. But give Intel EM64T systems a chance because they are
supposed to be correct there.
The advantage is that there is a chance to actually log uncorrected
machine checks after the reset.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On x86_64 arches, there is no way to choose ACPI_NUMA without having to choose
K8_NUMA. CONFIG_K8_NUMA is not needed for Intel EM64T NUMA boxes. It also
looks odd if you have to select ACPI_NUMA from the power management menu.
This patch fixes those oddities. Patch does the following:
1. Makes NUMA a config option like other arches
2. Makes topology detection options like K8_NUMA dependent on NUMA
3. Choosing ACPI NUMA detection can be done from the standard
"Processor type and features" menu
AK: I fixed up the dependencies and changed the help texts a bit
on top of Kiran's patch.
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Keeping this function does not makes sense because it's a copied (and
buggy) copy of sys_time. The only difference is that now.tv_sec (which is
a time_t, i.e. a 64-bit long) is copied (and truncated) into a int
(32-bit).
The prototype is the same (they both take a long __user *), so let's drop
this and redirect it to sys_time (and make sure it exists by defining
__ARCH_WANT_SYS_TIME).
Only disadvantage is that the sys_stime definition is also compiled (may be
fixed if needed by adding a separate __ARCH_WANT_SYS_STIME macro, and
defining it for all arch's defining __ARCH_WANT_SYS_TIME except x86_64).
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
B stepping were the first shipping Opterons. memcpy/memset/copy_page/
clear_page had special optimized version for them. These are really
old and in the minority now and the difference to the generic versions
(using rep microcode) is not that big anyways. So just remove them.
TODO: figure out optimized versions for Intel Netburst based EM64T
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Old code could retry for 10 seconds worst time. Only try it
for one second now.
Suggested by Yinghai Lu
Cc: Yinghai.Lu@amd.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fields obtained through cpuid vector 0x1(ebx[16:23]) and
vector 0x4(eax[14:25], eax[26:31]) indicate the maximum values and might not
always be the same as what is available and what OS sees. So make sure
"siblings" and "cpu cores" values in /proc/cpuinfo reflect the values as seen
by OS instead of what cpuid instruction says. This will also fix the buggy BIOS
cases (for example where cpuid on a single core cpu says there are "2" siblings,
even when HT is disabled in the BIOS.
http://bugzilla.kernel.org/show_bug.cgi?id=4359)
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When they were disabled before (e.g. after a panic) it's better
to keep them off, otherwise followon panics can happen from timer
interrupt handlers etc.
Drawback is that pageup in the console won't work anymore though.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
They report 40bit, but only have 36bits of physical address space.
This caused problems with setting up the correct masks for MTRR.
CPUID workaround for steppings 0F33h(supporting x86) and 0F34h(supporting x86
and EM64T). Detail info can be found at:
http://download.intel.com/design/Xeon/specupdt/30240216.pdfhttp://download.intel.com/design/Pentium4/specupdt/30235221.pdf
Signed-off-by: Shaohua Li<shaohua.li@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Compute the highest possible value for memnode_shift, in order to reduce
footprint of memnodemap[] to the minimum, thus making all users
(phys_to_nid(), kfree()), more cache friendly.
Before the patch :
Node 0 MemBase 0000000000000000 Limit 00000001ffffffff
Node 1 MemBase 0000000200000000 Limit 00000003ffffffff
Using 23 for the hash shift. Max adder is 3ffffffff
After the patch :
Node 0 MemBase 0000000000000000 Limit 00000001ffffffff
Node 1 MemBase 0000000200000000 Limit 00000003ffffffff
Using 33 for the hash shift.
In this case, only 2 bytes of memnodemap[] are used, instead of 2048
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This allows to run 64bit signal handlers in 64bit processes that run small
code snippets in compat mode.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With a NR_CPUS==128 kernel with CPU hotplug enabled we would waste 4MB
on per CPU data of all possible CPUs. The reason was that HOTPLUG
always set up possible map to NR_CPUS cpus and then we need to allocate
that much (each per CPU data is roughly ~32k now)
The underlying problem is that ACPI didn't tell us how many hotplug CPUs
the platform supports. So the old code just assumed all, which would
lead to this memory wastage.
This implements some new heuristics:
- If the BIOS specified disabled CPUs in the ACPI/mptables assume they
can be enabled later (this is bending the ACPI specification a bit,
but seems like a obvious extension)
- The user can overwrite it with a new additionals_cpus=NUM option
- Otherwise use half of the available CPUs or 2, whatever is more.
Cc: ashok.raj@intel.com
Cc: len.brown@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Minor victory on the continuous quest against all stray extern.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adding __initdata_* to asm-generic/sections.h
Replaces a lot of open coded externs in arch/x86_64/*
I had to change __bss_end to __bss_stop to match the other architectures.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We should zap the low mappings, as soon as possible, so that we can catch
kernel bugs more effectively. Previously early boot had NULL mapped
and didn't trap on NULL references.
This patch introduces boot_level4_pgt, which will always have low identity
addresses mapped. Druing boot, all the processors will use this as their
level4 pgt. On BP, we will switch to init_level4_pgt as soon as we enter C
code and zap the low mappings as soon as we are done with the usage of
identity low mapped addresses. On AP's we will zap the low mappings as
soon as we jump to C code.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Not go from the CPU number to an mapping array.
Mode number is often used now in fast paths.
This also adds a generic numa_node_id to all the topology includes
Suggested by Eric Dumazet
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix
arch/x86_64/kernel/aperture.c: In function #iommu_hole_init#:
arch/x86_64/kernel/aperture.c:199: warning: #aper_order# may be used uninitialized in this function
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
According to cpuid instruction in IA32 SDM-Vol2, when computing cpu model,
we need to consider extended model ID for family 0x6 also.
AK: Also added fixes/simplifcation from Petr Vandrovec
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove duplicate __cpuinit in smp.c. Already defined in init.h which is
already included.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Here's a patch that builds on Natalie Protasevich's IRQ compression
patch and tries to work for MPS boots as well as ACPI. It is meant for
a 4-node IBM x460 NUMA box, which was dying because it had interrupt
pins with GSI numbers > NR_IRQS and thus overflowed irq_desc.
The problem is that this system has 270 GSIs (which are 1:1 mapped with
I/O APIC RTEs) and an 8-node box would have 540. This is much bigger
than NR_IRQS (224 for both i386 and x86_64). Also, there aren't enough
vectors to go around. There are about 190 usable vectors, not counting
the reserved ones and the unused vectors at 0x20 to 0x2F. So, my patch
attempts to compress the GSI range and share vectors by sharing IRQs.
Cc: "Protasevich, Natalie" <Natalie.Protasevich@unisys.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
MC4_MISC - DRAM Errors Threshold Register realized under AMD K8 Rev F.
This register is used to count correctable and uncorrectable ECC errors that occur during DRAM read operations.
The user may interface through sysfs files in order to change the threshold configuration.
bank%d/error_count - reads current error count, write to clear.
bank%d/interrupt_enable - set/clear interrupt enable.
bank%d/threshold_limit - read/write the threshold limit.
APIC vector 0xF9 in hw_irq.h.
5 software defined bank ids in mce.h.
new apic.c function to setup threshold apic lvt.
defaults to interrupt off, count enabled, and threshold limit max.
sysfs interface created on /sys/devices/system/threshold.
AK: added some ifdefs to make it compile on UP
Signed-off-by: Jacob Shin <jacob.shin@amd.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The VM needs to know about lost memory in zones to accurately
balance dirty pages. This patch accounts mem_map in there too,
which fixes a constant errror of a few percent. Also some
other misc mappings and the kernel text itself are accounted
too.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a new 4GB GFP_DMA32 zone between the GFP_DMA and GFP_NORMAL zones.
As a bit of historical background: when the x86-64 port
was originally designed we had some discussion if we should
use a 16MB DMA zone like i386 or a 4GB DMA zone like IA64 or
both. Both was ruled out at this point because it was in early
2.4 when VM is still quite shakey and had bad troubles even
dealing with one DMA zone. We settled on the 16MB DMA zone mainly
because we worried about older soundcards and the floppy.
But this has always caused problems since then because
device drivers had trouble getting enough DMA able memory. These days
the VM works much better and the wide use of NUMA has proven
it can deal with many zones successfully.
So this patch adds both zones.
This helps drivers who need a lot of memory below 4GB because
their hardware is not accessing more (graphic drivers - proprietary
and free ones, video frame buffer drivers, sound drivers etc.).
Previously they could only use IOMMU+16MB GFP_DMA, which
was not enough memory.
Another common problem is that hardware who has full memory
addressing for >4GB misses it for some control structures in memory
(like transmit rings or other metadata). They tended to allocate memory
in the 16MB GFP_DMA or the IOMMU/swiotlb then using pci_alloc_consistent,
but that can tie up a lot of precious 16MB GFPDMA/IOMMU/swiotlb memory
(even on AMD systems the IOMMU tends to be quite small) especially if you have
many devices. With the new zone pci_alloc_consistent can just put
this stuff into memory below 4GB which works better.
One argument was still if the zone should be 4GB or 2GB. The main
motivation for 2GB would be an unnamed not so unpopular hardware
raid controller (mostly found in older machines from a particular four letter
company) who has a strange 2GB restriction in firmware. But
that one works ok with swiotlb/IOMMU anyways, so it doesn't really
need GFP_DMA32. I chose 4GB to be compatible with IA64 and because
it seems to be the most common restriction.
The new zone is so far added only for x86-64.
For other architectures who don't set up this
new zone nothing changes. Architectures can set a compatibility
define in Kconfig CONFIG_DMA_IS_DMA32 that will define GFP_DMA32
as GFP_DMA. Otherwise it's a nop because on 32bit architectures
it's normally not needed because GFP_NORMAL (=0) is DMA able
enough.
One problem is still that GFP_DMA means different things on different
architectures. e.g. some drivers used to have #ifdef ia64 use GFP_DMA
(trusting it to be 4GB) #elif __x86_64__ (use other hacks like
the swiotlb because 16MB is not enough) ... . This was quite
ugly and is now obsolete.
These should be now converted to use GFP_DMA32 unconditionally. I haven't done
this yet. Or best only use pci_alloc_consistent/dma_alloc_coherent
which will use GFP_DMA32 transparently.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
attached patch renames one instance of
/sys/devices/system/timer
to
/sys/devices/system/timer_pit
to avoid a name clash with another instance created in time.c.
Acked-by: Andi Kleen <ak@muc.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make some changes to the NEED_RESCHED and POLLING_NRFLAG to reduce
confusion, and make their semantics rigid. Improves efficiency of
resched_task and some cpu_idle routines.
* In resched_task:
- TIF_NEED_RESCHED is only cleared with the task's runqueue lock held,
and as we hold it during resched_task, then there is no need for an
atomic test and set there. The only other time this should be set is
when the task's quantum expires, in the timer interrupt - this is
protected against because the rq lock is irq-safe.
- If TIF_NEED_RESCHED is set, then we don't need to do anything. It
won't get unset until the task get's schedule()d off.
- If we are running on the same CPU as the task we resched, then set
TIF_NEED_RESCHED and no further action is required.
- If we are running on another CPU, and TIF_POLLING_NRFLAG is *not* set
after TIF_NEED_RESCHED has been set, then we need to send an IPI.
Using these rules, we are able to remove the test and set operation in
resched_task, and make clear the previously vague semantics of
POLLING_NRFLAG.
* In idle routines:
- Enter cpu_idle with preempt disabled. When the need_resched() condition
becomes true, explicitly call schedule(). This makes things a bit clearer
(IMO), but haven't updated all architectures yet.
- Many do a test and clear of TIF_NEED_RESCHED for some reason. According
to the resched_task rules, this isn't needed (and actually breaks the
assumption that TIF_NEED_RESCHED is only cleared with the runqueue lock
held). So remove that. Generally one less locked memory op when switching
to the idle thread.
- Many idle routines clear TIF_POLLING_NRFLAG, and only set it in the inner
most polling idle loops. The above resched_task semantics allow it to be
set until before the last time need_resched() is checked before going into
a halt requiring interrupt wakeup.
Many idle routines simply never enter such a halt, and so POLLING_NRFLAG
can be always left set, completely eliminating resched IPIs when rescheduling
the idle task.
POLLING_NRFLAG width can be increased, to reduce the chance of resched IPIs.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Con Kolivas <kernel@kolivas.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Run idle threads with preempt disabled.
Also corrected a bugs in arm26's cpu_idle (make it actually call schedule()).
How did it ever work before?
Might fix the CPU hotplugging hang which Nigel Cunningham noted.
We think the bug hits if the idle thread is preempted after checking
need_resched() and before going to sleep, then the CPU offlined.
After calling stop_machine_run, the CPU eventually returns from preemption and
into the idle thread and goes to sleep. The CPU will continue executing
previous idle and have no chance to call play_dead.
By disabling preemption until we are ready to explicitly schedule, this bug is
fixed and the idle threads generally become more robust.
From: alexs <ashepard@u.washington.edu>
PPC build fix
From: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
MIPS build fix
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
EXPORT_SYMBOL's for phys_proc_id and cpu_core_id were added this year but
never used.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reorganize the preempt_disable/enable calls to eliminate the extra preempt
depth. Changes based on Paul McKenney's review suggestions for the kprobes
RCU changeset.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Changes to the arch kprobes infrastructure to take advantage of the locking
changes introduced by usage of RCU for synchronization. All handlers are now
run without any locks held, so they have to be re-entrant or provide their own
synchronization.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
x86_64 changes to track kprobe execution on a per-cpu basis. We now track the
kprobe state machine independently on each cpu using a arch specific kprobe
control block.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following set of patches are aimed at improving kprobes scalability. We
currently serialize kprobe registration, unregistration and handler execution
using a single spinlock - kprobe_lock.
With these changes, kprobe handlers can run without any locks held. It also
allows for simultaneous kprobe handler executions on different processors as
we now track kprobe execution on a per processor basis. It is now necessary
that the handlers be re-entrant since handlers can run concurrently on
multiple processors.
All changes have been tested on i386, ia64, ppc64 and x86_64, while sparc64
has been compile tested only.
The patches can be viewed as 3 logical chunks:
patch 1: Reorder preempt_(dis/en)able calls
patches 2-7: Introduce per_cpu data areas to track kprobe execution
patches 8-9: Use RCU to synchronize kprobe (un)registration and handler
execution.
Thanks to Maneesh Soni, James Keniston and Anil Keshavamurthy for their
review and suggestions. Thanks again to Anil, Hien Nguyen and Kevin Stafford
for testing the patches.
This patch:
Reorder preempt_disable/enable() calls in arch kprobes files in preparation to
introduce locking changes. No functional changes introduced by this patch.
Signed-off-by: Ananth N Mavinakayahanalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The sys_ptrace boilerplate code (everything outside the big switch
statement for the arch-specific requests) is shared by most architectures.
This patch moves it to kernel/ptrace.c and leaves the arch-specific code as
arch_ptrace.
Some architectures have a too different ptrace so we have to exclude them.
They continue to keep their implementations. For sh64 I had to add a
sh64_ptrace wrapper because it does some initialization on the first call.
For um I removed an ifdefed SUBARCH_PTRACE_SPECIAL block, but
SUBARCH_PTRACE_SPECIAL isn't defined anywhere in the tree.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Paul Mackerras <paulus@samba.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-By: David Howells <dhowells@redhat.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andrew Morton suggested to move kprobes from kernel hacking menu, since
kernel hacking menu is in-appropriate for the Kprobes. This patch moves
Kprobes and Oprofile under instrumentation menu.
(akpm: it's not a natural fit, but things like djprobes and the s390 guys'
statistics library need a home)
Signed-of-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Cc: Philippe Elie <phil.el@wanadoo.fr>
Cc: John Levon <levon@movementarian.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes the x86-64 find_[first|next]_zero_bit() function for the
end-of-range case. It didn't test for a zero size, and the "rep scas"
would do entirely the wrong thing.
Signed-off-by: Alexandre Oliva <oliva@lsd.ic.unicamp.br>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reads from an HPET register require a round trip to the south bridge and are
almost as slow as PCI reads. By caching the last value we've written to the
comparator register, we can eliminate all HPET reads from the fast path in the
emulated RTC interrupt handler.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make sure that the RTC timer is in non-periodic mode; some stupid BIOS might
have initialized it to periodic mode.
Furthermore, don't set the SETVAL bit in the config register. This wouldn't
have any effect unless the timer was in period mode (which it isn't), and then
the actual timer frequency would be half that of the desired one because
incrementing the comparator in the interrupt handler would be done after the
hardware has already incremented it itself.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When the emulated RTC interrupt is no longer needed, we better disable it;
otherwise, we get a spurious interrupt whenever the timer has rolled over and
reaches the same comparator value.
Having a superfluous interrupt every five minutes doesn't hurt much, but it's
bad style anyway. ;-)
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Acked-by: "Pallipadi, Venkatesh" <venkatesh.pallipadi@intel.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Define jiffies_64 in kernel/timer.c rather than having 24 duplicated
defines in each architecture.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This ioctl doesn't exist for native i386.
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
