Move the IRQ tracking setup and teardown into the same routines that
do the IRQ setup and teardown. This keeps like activities together and
allows us to track exactly the number of vectors reserved from the OS,
which may be fewer than are available from the HW.
Change-ID: I6b2b1a955c5f0ac6b94c3084304ed0b2ea6777cf
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For future device support we do not want to map the whole CSR space since some
of it is mapped by other drivers with different mapping methods.
Note: As a side effect, the flash region (if exposed through the memory map)
gets unmapped too since it follows the future use region.
Change-ID: Ic729a2eacd692984220b1a415ff4fa0f98ea419a
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix some double blank lines and un-split a function declaration that all
fits on one line. Also make i40e_get_priv_flags static.
Change-ID: I11b5d25d1153a06b286d0d2f5d916d7727c58e4a
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the 10G and 40G AOC PHY types to the case statement in get_media_type
and ethtool get_settings so that the correct information gets reported
back to the user.
Change-ID: I1b4849d22199a9acf7c8807166d0317c1faad375
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the system administrator is requesting an offline diagnostic test using
'ethtool -t' then we should, you know, actually take the device offline
before doing the testing.
Change-ID: I6afa1cbfcc821c9ab6e6f47ed4d8dc2d8dd20e82
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some FW versions are incorrectly reporting a breakout cable as PHY type
0x3 when it should be 0x16 (I40E_PHY_TYPE_10GBASE_SFPP_CU).
If we get this value back from FW and the version is < 4.40, reassign it
to I40E_PHY_TYPE_10GBASE_SFPP_CU.
Change-ID: Ibb41a0e3cd2c0753744e8553959240df6ed13ae8
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During resets (possibly caused by a Tx hang) the driver would
accidentally clear the XPS mask for all queues back to 0.
This caused higher CPU utilization and had some other performance impacts
for transmit tests.
Change-ID: I95f112432c9e643a153eaa31cd28cdcbfdd01831
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use automatic sign extension by replacing 0xffff... constants
with ~(u64)0 or ~(u32)0.
Change-ID: I73cab4cd2611795bb12e00f0f24fafaaee07457c
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
0x2A is the NVM version so it has useful data but it is per image
version every image can have a different one. 0x18 is the dev starter
version which all the images for release will have the same version.
Of the two 0x18 is more useful and is what should be displayed.
Change-ID: Idf493da13a42ab211e2de0bef287f5de51033cca
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In CEE mode the firmware does not set the operational status bit of
the application TLV status as returned from the "Get CEE DCBX Oper Cfg"
AQ command. This occurs whenever a DCBX configuration is changed.
This is a workaround to remove the check for the operational and sync bits
of the application TLV status till a firmware fix is provided.
Change-ID: I1a31ff2fcadcb06feb5b55776a33593afc6ea176
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Modify our get and set LED functions so they ignore activity LEDs,
as we are required to blink the link LEDs only.
Change-ID: I647ea67a6fc95cbbab6e3cd01d81ec9ae096a9ad
Signed-off-by: Matt Jared <matthew.a.jared@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Recent changes to the driver initialization have caused the BW
configurations to not take effect. We use a BW configuration read and
write back to "kick" the Tx scheduler into action.
Change-ID: I94ab377c58d3a3986e3de62b6c199be3fd2ee5e6
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1. Use c_index and ring->c_index to determine how many TxCBs/TxBDs are
ready for cleanup
- c_index = the current value of TDMA_CONS_INDEX
- TDMA_CONS_INDEX is HW-incremented and auto-wraparound (0x0-0xFFFF)
- ring->c_index = __bcmgenet_tx_reclaim() cleaned up to this point on
the previous invocation
2. Add bcmgenet_tx_ring->clean_ptr
- index of the next TxCB to be cleaned
- incremented as TxCBs/TxBDs are processed
- value always in range [ring->cb_ptr, ring->end_ptr]
3. Fix incrementing of dev->stats.tx_packets
- should be incremented only when tx_cb_ptr->skb != NULL
These changes simplify __bcmgenet_tx_reclaim(). Furthermore, Tx ring size
can now be any value.
With the old code, Tx ring size had to be a power-of-2:
num_tx_bds = ring->size;
c_index &= (num_tx_bds - 1);
last_c_index &= (num_tx_bds - 1);
Signed-off-by: Petri Gynther <pgynther@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck says:
====================
ipv4/fib_trie: Cleanups to prepare for introduction of key vector
This patch series is meant to mostly just clean up the fib_trie to prepare
it for the introduction of the key_vector. As such there are a number of
minor clean-ups such as reformatting the tnode to match the format once the
key vector is introduced, some optimizations to drop the need for a leaf
parent pointer, and some changes to remove duplication of effort such as
the 2 look-ups that were essentially being done per node insertion.
v2: Added code to cleanup idx >> n->bits and explain unsigned long logic
Added code to prevent allocation when tnode size is larger than size_t
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to prevent us from attempting to allocate a tnode with
a size larger than what can be represented by size_t.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change updates the fib_table_lookup function so that it is in sync
with the fib_find_node function in terms of the explanation for the index
check based on the bits value.
I have also updated it from doing a mask to just doing a compare as I have
found that seems to provide more options to the compiler as I have seen it
turn this into a shift of the value and test under some circumstances.
In addition I addressed one minor issue in which we kept computing the key
^ n->key when checking the fib aliases. I pulled the xor out of the loop
in order to reduce the number of memory reads in the lookup. As a result
we should save a couple cycles since the xor is only done once much earlier
in the lookup.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fib_table was wrapped in several places with an
rcu_read_lock/rcu_read_unlock however after looking over the code I found
several spots where the tables were being accessed as just standard
pointers without any protections. This change fixes that so that all of
the proper protections are in place when accessing the table to take RCU
replacement or removal of the table into account.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we are going to compact the leaf and tnode we first need to make sure
the fields are all in the same place. In that regard I am moving the leaf
pointer which represents the fib_alias hash list to occupy what is
currently the first key_vector pointer.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that the insert and delete functions make use of
the tnode pointer returned in the fib_find_node call. By doing this we
will not have to rely on the parent pointer in the leaf which will be going
away soon.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that the parent pointer is returned by reference in
fib_find_node. By doing this I can use it to find the parent node when I
am performing an insertion and I don't have to look for it again in
fib_insert_node.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that leaf_walk_rcu takes a tnode and a key instead
of the trie and a leaf.
The main idea behind this is to avoid using the leaf parent pointer as that
can have additional overhead in the future as I am trying to reduce the
size of a leaf down to 16 bytes on 64b systems and 12b on 32b systems.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that we only call resize on the tnodes, instead of
from each of the leaves. By doing this we can significantly reduce the
amount of time spent resizing as we can update all of the leaves in the
tnode first before we make any determinations about resizing. As a result
we can simply free the tnode in the case that all of the leaves from a
given tnode are flushed instead of resizing with each leaf removed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=pJAi
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-4.1-20150304' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2015-03-04
this is a pull request of 3 patches for net-next/master.
Aaron Wu contributes three patches for the blackfin can driver, which
cleans up the driver and makes use of more platform independent code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sathya Perla says:
====================
be2net: patch set
Hi Dave, the following patch set includes three feature additions relating
to SR-IOV to be2net.
Patch 1 avoid creating a non-RSS default RXQ when FW allows it.
This prevents wasting one RXQ for each VF.
Patch 2 adds support for evenly distributing all queue & filter resources
across VFs. The FW informs the driver as to which resources are distributable.
Patch 3 implements the sriov_configure PCI method to allow runtime
enablement of VFs via sysfs.
Pls consider applying this patch-set to the net-next tree. Thanks!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the .sriov_configure() PCI method to allow for
runtime enabling/disabling of VFs. The module param "num_vfs" is now
deprecated.
At the time of driver load the PF-pool resources are allocated to the PF.
When the user enables VFs, the resources are then re-distributed across
PFs and VFs based on the number of VFs enabled.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When SR-IOV is enabled in the adapter, the FW distributes resources
evenly across the PF and it's VFs. This is currently done only for some
resources.
This patch adds support for a new cmd that queries the FW for the list
of resources for which the distribution is allowed and distributes them
accordingly.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On BE2, BE3 and Skhawk-R chips one non-RSS (called "default") RXQ was
needed to receive non-IP traffic. Some FW versions now export a
capability called IFACE_FLAGS_DEFQ_RSS where this requirement doesn't hold.
On such FWs the driver now does not create the non-RSS default queue.
This prevents wasting one RXQ per VF.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove Kconfig dependency and enable driver for
all ARCHs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings says:
====================
sh_eth changes for net-next
Some minor new features and fixes.
These depend in part on the series I sent earlier for net, specifically
"sh_eth: WARN on access to a register not implemented in a particular
chip" depends on "sh_eth: Fix RX recovery on R-Car in case of RX ring
underrun".
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The statistics registers have write-clear behaviour, which means we
will lose any increment between the read and write. Mitigate this by
only clearing when we read a non-zero value, so we will never falsely
report a total of zero. This also saves time as we only handle
error statistics here and they won't often be incremented.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are many different sets of registers implemented by the
different versions of this controller, and we can only expect this to
get more complicated in future. Limit how much ethtool needs to know
by including an explicit bitmap of which registers are included in the
dump, allowing room for future growth in the number of possible
registers.
As I don't have datasheets for all of these, I've only included
registers that are:
- defined in all 5 register type arrays, or
- used by the driver, or
- documented in the datasheet I have
Add one new capability flag so we can tell whether the RTRATE
register is implemented.
Delete the TSU_ADRL0 and TSU_ADR{H,L}31 definitions, as they weren't
used and the address table is already assumed to be contiguous.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we may silently read/write a register at offset 0. Change
this to WARN and then ignore the write or read-back all-ones.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least on the R8A7790, RFS8 reflects the RINT8 (multicast) MAC
status flag.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Header file was in arch dependent location arch/blackfin/include/asm/bfin_can.h,
Now move and merge the useful contents of header file into driver code, note
the original header file is reserved for full registers set access test by other
code so it survives.
Signed-off-by: Aaron Wu <Aaron.wu@analog.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Blackfin was built without MMU, old driver code access the IO space by
physical address, introduce the ioremap approach to be compitable with
the common style supporting MMU enabled arch.
Signed-off-by: Aaron Wu <Aaron.wu@analog.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Replace the blackfin arch dependent style of bfin_read/bfin_write with
common readw/writew
Signed-off-by: Aaron Wu <Aaron.wu@analog.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Eric W. Biederman says:
====================
Basic MPLS support take 2
On top of my two pending neighbour table prep patches here is the mpls
support refactored to use them, and edited to not drop routes when
an interface goes down. Additionally the addition of RTA_LLGATEWAY
has been replaced with the addtion of RTA_VIA. RTA_VIA being an
attribute that includes the address family as well as the address
of the next hop.
MPLS is at it's heart simple and I have endeavoured to maintain that
simplicity in my implemenation.
This is an implementation of a RFC3032 forwarding engine, and basic MPLS
egress logic. Which should make linux sufficient to be a mpls
forwarding node or to be a LSA (Label Switched Router) as it says in all
of the MPLS documents. The ingress support will follow but it deserves
it's own discussion so I am pushing it separately.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike IPv4 this code notifies on all cases where mpls routes
are added or removed and it never automatically removes routes.
Avoiding both the userspace confusion that is caused by omitting
route updates and the possibility of a flood of netlink traffic
when an interface goes doew.
For now reserved labels are handled automatically and userspace
is not notified.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change adds two new netlink routing attributes:
RTA_VIA and RTA_NEWDST.
RTA_VIA specifies the specifies the next machine to send a packet to
like RTA_GATEWAY. RTA_VIA differs from RTA_GATEWAY in that it
includes the address family of the address of the next machine to send
a packet to. Currently the MPLS code supports addresses in AF_INET,
AF_INET6 and AF_PACKET. For AF_INET and AF_INET6 the destination mac
address is acquired from the neighbour table. For AF_PACKET the
destination mac_address is specified in the netlink configuration.
I think raw destination mac address support with the family AF_PACKET
will prove useful. There is MPLS-TP which is defined to operate
on machines that do not support internet packets of any flavor. Further
seem to be corner cases where it can be useful. At this point
I don't care much either way.
RTA_NEWDST specifies the destination address to forward the packet
with. MPLS typically changes it's destination address at every hop.
For a swap operation RTA_NEWDST is specified with a length of one label.
For a push operation RTA_NEWDST is specified with two or more labels.
For a pop operation RTA_NEWDST is not specified or equivalently an emtpy
RTAN_NEWDST is specified.
Those new netlink attributes are used to implement handling of rt-netlink
RTM_NEWROUTE, RTM_DELROUTE, and RTM_GETROUTE messages, to maintain the
MPLS label table.
rtm_to_route_config parses a netlink RTM_NEWROUTE or RTM_DELROUTE message,
verify no unhandled attributes or unhandled values are present and sets
up the data structures for mpls_route_add and mpls_route_del.
I did my best to match up with the existing conventions with the caveats
that MPLS addresses are all destination-specific-addresses, and so
don't properly have a scope.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reading and writing addresses in network byte order in netlink is
traditional and I see no reason to change that. MPLS is interesting
as effectively it has variabely length addresses (the MPLS label
stack). To represent these variable length addresses in netlink
I use a valid MPLS label stack (complete with stop bit).
This achieves two things: a well defined existing format is used,
and the data can be interpreted without looking at it's length.
Not needed to look at the length to decode the variable length
network representation allows existing userspace functions
such as inet_ntop to be used without needed to change their
prototype.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mpls_route_add and mpls_route_del implement the basic logic for adding
and removing Next Hop Label Forwarding Entries from the MPLS input
label map. The addition and subtraction is done in a way that is
consistent with how the existing routing table in Linux are
maintained. Thus all of the work to deal with NLM_F_APPEND,
NLM_F_EXCL, NLM_F_REPLACE, and NLM_F_CREATE.
Cases that are not clearly defined such as changing the interpretation
of the mpls reserved labels is not allowed.
Because it seems like the right thing to do adding an MPLS route without
specifying an input label and allowing the kernel to pick a free label
table entry is supported. The implementation is currently less than optimal
but that can be changed.
As I don't have anything else to test with only ethernet and the loopback
device are the only two device types currently supported for forwarding
MPLS over.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This sysctl gives two benefits. By defaulting the table size to 0
mpls even when compiled in and enabled defaults to not forwarding
any packets. This prevents unpleasant surprises for users.
The other benefit is that as mpls labels are allocated locally a dense
table a small dense label table may be used which saves memory and
is extremely simple and efficient to implement.
This sysctl allows userspace to choose the restrictions on the label
table size userspace applications need to cope with.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change adds a new Kconfig option MPLS_ROUTING.
The core of this change is the code to look at an mpls packet received
from another machine. Look that packet up in a routing table and
forward the packet on.
Support of MPLS over ATM is not considered or attempted here. This
implemntation follows RFC3032 and implements the MPLS shim header that
can pass over essentially any network.
What RFC3021 refers to as the as the Incoming Label Map (ILM) I call
net->mpls.platform_label[]. What RFC3031 refers to as the Next Label
Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the
label fordwarding information base (lfib) might also be valid.
Further the implemntation forwards packets as described in RFC3032.
There is no need and given the original motivation for MPLS a strong
discincentive to have a flexible label forwarding path. In essence
the logic is the topmost label is read, looked up, removed, and
replaced by 0 or more new lables and the sent out the specified
interface to it's next hop.
Quite a few optional features are not implemented here. Among them
are generation of ICMP errors when the TTL is exceeded or the packet
is larger than the next hop MTU (those conditions are detected and the
packets are dropped instead of generating an icmp error). The traffic
class field is always set to 0. The implementation focuses on IP over
MPLS and does not handle egress of other kinds of protocols.
Instead of implementing coordination with the neighbour table and
sorting out how to input next hops in a different address family (for
which there is value). I was lazy and implemented a next hop mac
address instead. The code is simpler and there are flavor of MPLS
such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is
appropriate so a next hop by mac address would need to be implemented
at some point.
Two new definitions AF_MPLS and PF_MPLS are exposed to userspace.
Decoding the mpls header must be done by first byeswapping a 32bit bit
endian word into the local cpu endian and then bit shifting to extract
the pieces. There is no C bit-field that can represent a wire format
mpls header on a little endian machine as the low bits of the 20bit
label wind up in the wrong half of third byte. Therefore internally
everything is deal with in cpu native byte order except when writing
to and reading from a packet.
For management simplicity if a label is configured to forward out
an interface that is down the packet is dropped early. Similarly
if an network interface is removed rt_dev is updated to NULL
(so no reference is preserved) and any packets for that label
are dropped. Keeping the label entries in the kernel allows
the kernel label table to function as the definitive source
of which labels are allocated and which are not.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This refactoring is needed to allow more than just mpls gso
support to be built into the mpls moddule.
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric W. Biederman says:
====================
Neighbour table prep for MPLS
In preparation for using the IPv4 and IPv6 neighbour tables in my mpls
code this patchset factors out ___neigh_lookup_noref from
__ipv4_neigh_lookup_noref, __ipv6_lookup_noref and neigh_lookup.
Allowing the lookup logic to be shared between the different
implementations. At what appears to be no cost. (Aka the same assembly
is generated for ip6_finish_output2 and ip_finish_output2).
After that I add a simple function that takes an address family and an
address consults the neighbour table and sends the packet to the
appropriate location. The address family argument decoupls callers
of neigh_xmit from the addresses families the packets are sent over.
(Aka The ipv6 module can be loaded after mpls and a previously
configured ipv6 next hop will start working).
The refactoring in ___neigh_lookup_noref may be a bit overkill but it
feels like the right thing to do. Especially since the same code is
generated.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For MPLS I am building the code so that either the neighbour mac
address can be specified or we can have a next hop in ipv4 or ipv6.
The kind of next hop we have is indicated by the neighbour table
pointer. A neighbour table pointer of NULL is a link layer address.
A non-NULL neighbour table pointer indicates which neighbour table and
thus which address family the next hop address is in that we need to
look up.
The code either sends a packet directly or looks up the appropriate
neighbour table entry and sends the packet.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While looking at the mpls code I found myself writing yet another
version of neigh_lookup_noref. We currently have __ipv4_lookup_noref
and __ipv6_lookup_noref.
So to make my work a little easier and to make it a smidge easier to
verify/maintain the mpls code in the future I stopped and wrote
___neigh_lookup_noref. Then I rewote __ipv4_lookup_noref and
__ipv6_lookup_noref in terms of this new function. I tested my new
version by verifying that the same code is generated in
ip_finish_output2 and ip6_finish_output2 where these functions are
inlined.
To get to ___neigh_lookup_noref I added a new neighbour cache table
function key_eq. So that the static size of the key would be
available.
I also added __neigh_lookup_noref for people who want to to lookup
a neighbour table entry quickly but don't know which neibhgour table
they are going to look up.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the STP timer fires, it can call br_ifinfo_notify(),
which in turn ends up in the new br_get_link_af_size().
This function is annotated to be using RTNL locking, which
clearly isn't the case here, and thus lockdep warns:
===============================
[ INFO: suspicious RCU usage. ]
3.19.0+ #569 Not tainted
-------------------------------
net/bridge/br_private.h:204 suspicious rcu_dereference_protected() usage!
Fix this by doing RCU locking here.
Fixes: b7853d73e3 ("bridge: add vlan info to bridge setlink and dellink notification messages")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
