This patch optimizes the timer load and start sequence. By combining the
load and start a needless posted wait can be removed from the system timer
execution path.
* Before patch register writes are taking up .078% @ 500MHz during idle.
Address |total |min |max |avr |count|ratio%
old\process\default_idle|7.369s |0.0us|999.902ms|14.477ms|509. |62.661%
ld\Global\cpu_v7_do_idle|4.265s |0.0us|375.786ms|24.374ms|175. |36.270%
(UNKNOWN)|17.503ms|0.us|531.080us|5.119us|3419. |0.148%
r\omap_dm_timer_set_load|8.135ms|0.0us|79.887us|15.065us|540. |0.069% <--
\vmlinux-old\Global\_end|2.023ms|0.0us|4.000us|0.560us|3613. |0.017%
-old\Global\__raw_readsw|1.962ms|0.0us|108.610us|9.167us|214. |0.016%
old\smc91x\smc_interrupt|1.353ms|0.0us|10.212us|2.348us|576. |0.011%
s/namei\__link_path_walk|1.161ms|0.0us|4.310us|0.762us| 1524. |0.009%
\omap_dm_timer_write_reg|1.085ms|0.0us|126.150us|2.153us|504. |0.009% <--
* After patch timer functions do not show up in top listings for long captures.
Signed-off-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds the use of write posting for the timer. Previously, every
write could lock the requestor for almost 3x32KHz cycles. This patch only
synchronizes before writes and reads instead of after them and it does
it on per register basis. Doing it this way there is some chance to hide
some of the sync latency. It also removes some needless reads when
non-posted mode is there. With out this fix the read/writes take almost
2% CPU load @500MHz just waiting on tick timer registers.
Also define new 34xx only registers.
Signed-off-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Channel should be marked active only when DMA is really started. Otherwise
just omap_request_dma, omap_dma_link_lch and omap_dma_unlink_lch will cause
incorrect dump_stack().
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
arch/arm/plat-omap/clock.c:397: warning: "struct cpufreq_frequency_table" declared inside parameter list
arch/arm/plat-omap/clock.c:397: warning: its scope is only this definition or declaration, which is probably not what you want
arch/arm/plat-omap/clock.c: In function `clk_init_cpufreq_table':
arch/arm/plat-omap/clock.c:402: error: structure has no member named `clk_init_cpufreq_table'
arch/arm/plat-omap/clock.c:403: error: structure has no member named `clk_init_cpufreq_table'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Function enable_lnk does incorrect channel link on non-omap1 builds if chain
is created manually with omap_request_dma and omap_dma_link_lch functions.
Fix this by making sure that next_linked_ch field is initialized to -1 just
in omap_request_dma.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
None of these files use any of the functionality promised by
asm/semaphore.h. It's possible that they rely on it dragging in some
unrelated header file, but I can't build all these files, so we'll have
fix any build failures as they come up.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
This patch changes 24xx to use shared clock code and new register
access.
Note that patch adds some temporary OLD_CK defines to keep patch
more readable. These temporary defines will be removed in the next
patch. Also not all clocks are changed in this patch to limit the
size.
Also, the patch fixes few incorrect clock defines in clock24xx.h.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch changes 24xx to use new register access, except for clock
framework. Clock framework register access will get updates in the
next patch.
Note that board-*.c files change GPMC (General Purpose Memory Controller)
access to use gpmc_cs_write_reg() instead of accessing the registers
directly. The code also uses gpmc_fck instead of it's parent clock
core_l3_ck for GPMC clock.
The H4 board file also adds h4_init_flash() function, which specify the
flash start and end addresses.
Also note that sleep.S removes some unused registers addresses.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds common register access for 24xx and 34xx power
and clock management in order to share code between 24xx and 34xx.
Only change USB platform init code to use new register access, other
access will be changed in later patches.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Misc clean-up for the mux code and remove some unnecessary
ifdefs. Patch changes debug function so it can be used on
both 24xx and 34xx.
Changes are mostly for omap2, but patch also cleans up some
omap1 and common mux code.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move now OMAP1-specific timer32k code to mach-omap1 since OMAP2/3 32k
timers are done in gptimer code.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since 32k timer code is moving to OMAP1 specific dir, move the
32k-based sched_clock() into common code where it is based on the 32k
sync counter and can be used even when using MPU timer.
While moving, change the ticks-to-nsecs conversion to use the helper
functions provided by clocksource.h.
Also removed the unused ticks_to_usec, leaving only ticks_to_nsec.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On OMAP2/3, the gp-timer code can be used for a 32kHz timer simply by
setting the source to be the 32k clock instead of sys_clk.
This patch uses the mach-omap2/timer-gp.c code for 32kHz timer on
OMAP2, moving the logic into mach-omap2/timer-gp.c, and not using
plat-omap/timer32k.c which, for OMAP2, is redundant with the timer-gp
code.
Also, if CONFIG_OMAP_32K_TIMER is enabled, the gptimer-based
clocksource is not used. Instead the default 32k sync counter is used
as the clocksource (see the clocksource in plat-omap/common.c.) This
is important for sleep/suspend so there is a valid counter during
sleep. Note that the suspend/sleep code needs fixing to check for
overflows of this counter.
In addition, the OMAP2/3 details are removed from timer32k.c leaving
that with only OMAP1 specifics. A follow-up patch will move it from
plat-omap common code to mach-omap1.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use omap processor specific function depending on system type.
Based on an earlier patch by Klaus Pedersen <klaus.k.pedersen@nokia.com>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch changes pin multiplexing init to allow registering
custom function. The omap_cfg_reg() func will be split into
omap processor specific functions in later patch.
This is done to make adding omap3 pin multiplexing easier.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently, the GPIO interrupt handling is duplicating some of the work
done by the generic IRQ handlers (handle_edge_irq, handle_level_irq)
such as detecting nesting, handling re-triggers etc. Remove this
duplication and use generic hooks based on IRQ type.
Using generic IRQ handlers ensures correct behavior when using
threaded interrupts introduced by the -rt patch.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clearing was moved to the unmask hook because it is known to run
after the interrupt handler has actually run. Before this patch, if
interrupts are threaded, the clearing/unmasking of level triggered
interrupts would be done before the threaded handler actually ran.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Update OMAP to use the new GPIO implementation framework. This is just a
quick'n'dirty update ... more code could now be removed, ideally as part
of cleaning up the entire OMAP GPIO infrastructure ...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch changes the return value of omap_dma_chain_a_transfer
to 0 on success instead of the flag 'start_dma', which wasn't really useful
for anything.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Although audio and dsp drivers are not integrated yet,
allow compiling in mailbox and mcbsp to see any build
warnings.
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO IRQ unmask doesn't actually do anything useful. The problem is
hidden by a separate explicit mass unmask at the end of the chained
bank handler.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
One-shot mode was broken in MPU-timer support for OMAP1 due to a typo.
Also, ensure timer is stopped before changing the auto-reload flag.
The TRM says changing the AR flag when timer is running is undefined.
Also set GENERIC_CLOCKEVENTS for all omaps.
Signed-off-by: Tim Bird <tim.bird@am.sony.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix some spinlock issues reported by lockdep: since the gpio bank
locks can be aquired in both irq and non-irq contexts, they need
to be consistent about always using the irq-safe variants.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In mainline, the "old style" I2C registration was only removed for
OMAP2, leading to init-time bugs (regressions) like:
sysfs: duplicate filename 'i2c_omap.1' can not be created
------------[ cut here ]------------
WARNING: at fs/sysfs/dir.c:424 sysfs_add_one+0x40/0xd4()
Modules linked in:
... deletia ...
[<c0036a38>] (omap_init_i2c+0x0/0x50) from [<c000cea8>] (omap_init_devices+0x10/0x24)
r4:c001e000
[<c000ce98>] (omap_init_devices+0x0/0x24) from [<c0008684>] (do_initcalls+0x78/0x200)
... deletia ...
---[ end trace ca143223eefdc828 ]---
kobject_add_internal failed for i2c_omap.1 with -EEXIST, don't try to register things with the same name in the same directory.
The fix is obvious: remove the old init code, it's no longer needed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove false lockdep warnings about lock recursion when declaring
IRQs as being wake-capable, by marking putting GPIO irq_desc locks
into their own class.
(Thanks to Peter Zijlstra for helping track down such a small
fix to this problem.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This makes parameter passing to DMA handlers uniform between non-chained
and chained transfers and makes debugging easier. Additional data like
chain_id can be always passed to handlers via callback data if needed.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This helper module simplifies I2C bus registration for different OMAP
platforms by doing registration in one place only and to allow board
specific bus configuration like clock rate and number of busses configured.
Helper should cover OMAP processors from first to third generation.
This patch just adds the feature and current implementation cleanup and
board file modifications will be done in following patches.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add DM timer support for OMAP3.
Fixed source clocks for 3430 by Paul Walmsley <paul@pwsan.com>.
Signed-off-by: Syed Mohammed Khasim <x0khasim@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cleanup DM timer list for OMAP2 and OMAP1 to allow
adding support for 3430.
Signed-off-by: Syed Mohammed Khasim <x0khasim@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add DMA support for chaining and 3430.
Also remove old DEBUG_PRINTS as noted by Russell King.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add 24xx GPIO debounce support. Also minor formatting
clean-up.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds 3430 gpio support.
It also contains a fix by Paul Walmsley <paul@pwsan.com> to use the
correct clock names for OMAP3430.
Signed-off-by: Syed Mohammed Khasim <x0khasim@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On OMAP1 some McBSP features depend on DSP. Also export
polling functions as suggested by Luis Cargnini.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patchset adds a flags variable to reserve_bootmem() and uses the
BOOTMEM_EXCLUSIVE flag in crashkernel reservation code to detect collisions
between crashkernel area and already used memory.
This patch:
Change the reserve_bootmem() function to accept a new flag BOOTMEM_EXCLUSIVE.
If that flag is set, the function returns with -EBUSY if the memory already
has been reserved in the past. This is to avoid conflicts.
Because that code runs before SMP initialisation, there's no race condition
inside reserve_bootmem_core().
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix powerpc build]
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: <linux-arch@vger.kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
smc91x is shared between many different platforms. Each platform needs
to specify the interrupt type, and in some cases the irq type depends
on more than just the build configuration - it depends on runtime
checks.
Rather than throwing this code into the SMC_IRQ_FLAGS definition, provide
a way for these flags to be passed via the IRQ resource itself.
Note that IRQF_TRIGGER_* constants are intentionally defined to correspond
with the IORESOURCE_IRQ_* interrupt type flags, in much the same way that
the low bits of PCI iomem resources correspond with the BAR flag bits.
Also provide a way to configure smc91x to read the IRQ flags from the
resource. Once all platforms have been converted over (signified
by all definitions of SMC_IRQ_FLAGS being -1) SMC_IRQ_FLAGS should
be removed.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Nicolas Pitre <nico@cam.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
This patch converts arm's OMAP mailbox driver to use
blk_end_request interfaces.
If the original code was converted literally, blk_end_request would
be called with '-EIO' because end_that_request_last() were called
with '0' (i.e. failure).
But I think these '0's are bugs in the original code because it's
unlikely that all requests are treated as failure.
(The bugs should have no effect unless these requests have an end_io
callback.)
So I changed them to pass '0' (i.e. success) to blk_end_request.
Cc: Toshihiro Kobayashi <toshihiro.kobayashi@nokia.com>
Cc: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
mach-integrator/pci_v3.c: no need to reference 'irq' arg, its constant
mach-omap1/pm.c: remove extra whitespace
arch/arm/mach-sa1100/ssp.c: remove braces around single C stmt
arch/arm/plat-omap/mcbsp.c:
- remove pointless casts from void*
- make longer lines more readable
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
All kobjects require a dynamically allocated name now. We no longer
need to keep track if the name is statically assigned, we can just
unconditionally free() all kobject names on cleanup.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a section error on OMAP when the framebuffer is enabled.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
