Detect if firmware is running run-time and download / start it only
when needed. Detection is done by reading IF frequency value.
Garbage value is returned by firmware when it is not running,
otherwise correct value is returned.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The chips supported by the si2157 driver have two IF outputs (either
pins 12+13 or pins 9+11). Instead of hardcoding the output to be used
add an option to choose which output shall be used.
As this patch changes the default behaviour, the IF interface is
specified in each driver currently using si2157 driver. This is to
keep bisectability.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
For supporting ATSC and QAM modes the driver should use a smaller IF frequency than 5 MHz.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Carry struct i2c_client pointer in tuner_priv. This driver is I2C driver,
which is represented as a struct i2c_client, so better to carry this top
level structure for each routine in order to unify things.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
'dev' is likely most common name in kernel for structure containing
device state instance, so rename it in order to keep things
consistent.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Silicon Labs Si2146 tuner seems to work with the same driver as the Si2157,
but there a few exceptions. The powerup command seems to be quite a bit
different. In addition there's a property 0207 that requires a different value.
Thus another entry is created in the si2157_id table to support also si2146 in
this driver.
The datasheet is available on manufacturer's website:
http://www.silabs.com/support%20documents/technicaldocs/Si2146-short.pdf
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds support for Si2147-A30 tuner. Fairly trivial, no firmware needed for this tuner. However, command 14 00 02 07 01 00 seems to be mandatory. On Si2157 and Si2158 the value 0x0100 is the default value, so this patch does not impact the existing tuners/devices. On Si2147 the default is 0x0000 and I can't get a lock with that value.
While here, fix the return length of the previous set command to 4 bytes.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add a variable into state to keep track if firmware has been loaded or not.
Skip firmware loading in case it is already loaded (resume from sleep).
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is needed for PCTV 522e support.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for Si2158 A20 chip.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
We want also read data from firmware. Add support for it. Copied from
si2168 driver.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Silicon Labs Si2157 silicon tuner driver.
Currently it supports only DVB-T.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
