These structure members were removed in 2012 by the commit ffbbdd2132
("spi: create a message queueing infrastructure").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Handle EPROBE_DEFER explicitly so that we ensure that we get the DMA
channel specified in the device tree, instead of depending on the DMA
controller getting probed before us.
Signed-off-by: Rabin Vincent <rabin.vincent@axis.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit fd316941c ("spi/pl022: disable port when unused") introduced a race,
which leads to possible driver lock up (easily reproducible on SMP).
The problem happens in giveback() function where the completion of the transfer
is signalled to SPI subsystem and then the HW SPI controller is disabled. Another
transfer might be setup in between, which brings driver in locked-up state.
Exact event sequence on SMP:
core0 core1
=> pump_transfers()
/* message->state == STATE_DONE */
=> giveback()
=> spi_finalize_current_message()
=> pl022_unprepare_transfer_hardware()
=> pl022_transfer_one_message
=> flush()
=> do_interrupt_dma_transfer()
=> set_up_next_transfer()
/* Enable SSP, turn on interrupts */
writew((readw(SSP_CR1(pl022->virtbase)) |
SSP_CR1_MASK_SSE), SSP_CR1(pl022->virtbase));
...
=> pl022_interrupt_handler()
=> readwriter()
/* disable the SPI/SSP operation */
=> writew((readw(SSP_CR1(pl022->virtbase)) &
(~SSP_CR1_MASK_SSE)), SSP_CR1(pl022->virtbase));
Lockup! SPI controller is disabled and the data will never be received. Whole
SPI subsystem is waiting for transfer ACK and blocked.
So, only signal transfer completion after disabling the controller.
Fixes: fd316941c (spi/pl022: disable port when unused)
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
"flag" variable does nothing, remove it.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
PL022 Programmers model explicitely states "do not modify undefined register
bits". Correct the "all enable" interrupt mask so that it only enables defined
ones.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to PL022 specification, TNF bit states for "Transmit FIFO Not full".
So the logic here is inverted. But "Receive Overrun Interrupt", which is handled
here, is only triggered on Rx errors. So instead of fixing the if statement,
remove the whole message.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SET_PM_RUNTIME_PM_OPS() and SET_RUNTIME_PM_OPS() macros are
identical except that one of them is not empty for CONFIG_PM set,
while the other one is not empty for CONFIG_PM_RUNTIME set,
respectively.
However, after commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if
PM_SLEEP is selected) PM_RUNTIME is always set if PM is set, so one
of these macros is now redundant.
For this reason, replace SET_PM_RUNTIME_PM_OPS() with
SET_RUNTIME_PM_OPS() everywhere and redefine the SET_PM_RUNTIME_PM_OPS
symbol as SET_RUNTIME_PM_OPS in case new code is starting to use the
macro being removed here.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When mapped RX DMA entries are unmapped in an error condition when DMA
is firstly configured in the driver, the number of TX DMA entries was
passed in, which is incorrect
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Add support for a extended PL022 which has an extra register for controlling up
to five chip select signals. This controller is found on the AXM5516 SoC.
Unfortunately the PrimeCell identification registers are identical to a
standard ARM PL022. To work around this, the peripheral ID must be overridden
in the device tree using the "arm,primecell-periphid" property with the value
0x000b6022.
Signed-off-by: Anders Berg <anders.berg@avagotech.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently this driver is missing a check on the return value of devm_kzalloc,
which would cause a NULL pointer dereference in a OOM situation.
This patch adds a missing check.
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When building on 64 bit architectures the use of bitwise negation generates
constants larger than 32 bits which won't fit in u32s used to represent
32 bit register values on the device. Explicitly cast to let the compiler
know that the higher bits are not significant and can be discarded.
Signed-off-by: Mark Brown <broonie@linaro.org>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Previously only the resources controlled by the driver were put into
low power state at system suspend. Both the amba bus and a potential
power domain were ignored.
Moreover, while putting the device into low power state we first
brought it back to full power, but for no particular reason.
To handle both issues above, use pm_runtime_force_suspend|resume() from
the system suspend|resume callbacks.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Convert to the SET_PM_RUNTIME_PM macro while defining the runtime PM
callbacks. This means the callbacks becomes available for both
CONFIG_PM_SLEEP and CONFIG_PM_RUNTIME, which is needed to handle the
combinations of these scenarios.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The driver core is now taking care of putting our pins into default
state at probe. Thus we can remove the redundant call for it in probe.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make use of clk_prepare_enable and clk_disable_unprepare to simplify
code. No functional change.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
When the driver was converted to clk_prepare() the suspend path didn't
have any changes made so the clock remains prepared throughout the runtime
of the driver. Unprepare it when suspended so that any savings that can be
made as a result are made.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Change raw printk() call to dev_info() to provide a better message
to userspace so it can properly identify the device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use devm_spi_register_master() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
'break' immediately after return has no effect.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
When CONFIG_ARM_LPAE=y the following build warning is generated:
drivers/spi/spi-pl022.c:2178:9: warning: format '%x' expects argument of type 'unsigned int', but argument 2 has type 'resource_size_t' [-Wformat]
According to Documentation/printk-formats.txt '%pa' can be used to properly
print 'resource_size_t'.
Reported-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
- A large slew of improvements of the Genric pin configuration
support, and deployment in four different platforms:
Rockchip, Super-H PFC, ABx500 and TZ1090. Support BIAS_BUS_HOLD,
get device tree parsing and debugfs support into shape.
- We also have device tree support with generic naming conventions
for the generic pin configuration.
- Delete the unused and confusing direct pinconf API. Now state
transitions is *the* way to control pins and multiplexing.
- New drivers for Rockchip, TZ1090, and TZ1090 PDC.
- Two pin control states related to power management are now
handled in the device core: "sleep" and "idle", removing a lot
of boilerplate code in drivers. We do not yet know if this is
the final word for pin PM, but it already make things a lot
easier to handle.
- Handle sparse GPIO ranges passing a list of disparate pins, and
utilize these in the new BayTrail (x86 Atom SoC) driver.
- Make the sunxi (AllWinner) driver handle external interrupts.
- Make it possible for pinctrl-single to handle the case where
several pins are managed by a single register, and augment it to
handle sleep modes.
- Cleanups and improvements for the abx500 drivers.
- Move Sirf pin control drivers to their own directory, support
save/restore of context and add support for the SiRFatlas6 SoC.
- PMU muxing for the Dove pinctrl driver.
- Finalization and support for VF610 in the i.MX6 pinctrl driver.
- Smoothen out various Exynos rough edges.
- Generic cleanups of various kinds.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=EbAf
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control changes from Linus Walleij:
- A large slew of improvements of the Genric pin configuration support,
and deployment in four different platforms: Rockchip, Super-H PFC,
ABx500 and TZ1090. Support BIAS_BUS_HOLD, get device tree parsing
and debugfs support into shape.
- We also have device tree support with generic naming conventions for
the generic pin configuration.
- Delete the unused and confusing direct pinconf API. Now state
transitions is *the* way to control pins and multiplexing.
- New drivers for Rockchip, TZ1090, and TZ1090 PDC.
- Two pin control states related to power management are now handled in
the device core: "sleep" and "idle", removing a lot of boilerplate
code in drivers. We do not yet know if this is the final word for
pin PM, but it already make things a lot easier to handle.
- Handle sparse GPIO ranges passing a list of disparate pins, and
utilize these in the new BayTrail (x86 Atom SoC) driver.
- Make the sunxi (AllWinner) driver handle external interrupts.
- Make it possible for pinctrl-single to handle the case where several
pins are managed by a single register, and augment it to handle sleep
modes.
- Cleanups and improvements for the abx500 drivers.
- Move Sirf pin control drivers to their own directory, support
save/restore of context and add support for the SiRFatlas6 SoC.
- PMU muxing for the Dove pinctrl driver.
- Finalization and support for VF610 in the i.MX6 pinctrl driver.
- Smoothen out various Exynos rough edges.
- Generic cleanups of various kinds.
* tag 'pinctrl-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (82 commits)
pinctrl: vt8500: wmt: remove redundant dev_err call in wmt_pinctrl_probe()
pinctrl: remove bindings for pinconf options needing more thought
pinctrl: remove slew-rate parameter from tz1090
pinctrl: set unit for debounce time pinconfig to usec
pinctrl: more clarifications for generic pull configs
pinctrl: rip out the direct pinconf API
pinctrl-tz1090-pdc: add TZ1090 PDC pinctrl driver
pinctrl-tz1090: add TZ1090 pinctrl driver
pinctrl: samsung: Staticize drvdata_list
pinctrl: rockchip: Add missing irq_gc_unlock() call before return error
pinctrl: abx500: rework error path
pinctrl: abx500: suppress hardcoded value
pinctrl: abx500: factorize code
pinctrl: abx500: fix abx500_gpio_get()
pinctrl: abx500: fix abx500_pin_config_set()
pinctrl: abx500: Add device tree support
sh-pfc: Guard DT parsing with #ifdef CONFIG_OF
pinctrl: add Intel BayTrail GPIO/pinctrl support
pinctrl: fix pinconf_ops::pin_config_dbg_parse_modify kerneldoc
pinctrl: Staticize local symbols
...
Conflicts:
drivers/net/ethernet/ti/davinci_mdio.c
drivers/pinctrl/Makefile
In the past we controlled the selection of DMA for a certain
host by a boolean switch in the platform data. Currently
there is no way to enable DMA on a PL022 probed from the
device tree. Let's default to trying to obtain DMA channels
in the DT case, and then we can always fail (and thus fall
back to PIO mode).
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This utilize the new pinctrl core PM helpers to transition
the driver to "sleep" and "idle" states, cutting away some
boilerplate code.
Cc: Hebbar Gururaja <gururaja.hebbar@ti.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With the new OF DMA binding, it is possible to completely avoid the
need for platform_data for configuring a DMA channel. In cases where the
platform has already been converted, calling dma_request_slave_channel
should get all the necessary information from the device tree.
Like the patch that converts the dw_dma controller, this is completely
untested and is looking for someone to try it out.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: spi-devel-general@lists.sourceforge.net
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Vinod Koul <vinod.koul@linux.intel.com>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-arm-kernel@lists.infradead.org
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Bill Pemberton has done most of the legwork on this series. I've used
his script to purge the attributes from the drivers/gpio tree.
Reported-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
A bunch of fixes here, mostly minor except for the pl022 which has just
been a bit of a shambles all round, the recent runtime PM changes have
as far as I can tell never worked so they're just getting thrown out.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=9XvI
-----END PGP SIGNATURE-----
Merge tag 'spi-linus' into spi-next
spi: Fixes for v3.7
A bunch of fixes here, mostly minor except for the pl022 which has just
been a bit of a shambles all round, the recent runtime PM changes have
as far as I can tell never worked so they're just getting thrown out.
Conflicts:
drivers/spi/spi-pl022.c
[Originally sent by Ulf as two changes, squashed down into one with a
redone changelog, thanks to Russell King for analysis. -- broonie]
This reverts commit 688723 (spi/pl022: enable runtime PM) and commit
2fb30d (spi/pl022: fix spi-pl022 pm enable at probe).
Commit "spi/pl022: enable runtime PM" introduced runtime PM issues as it
interacted badly with the work Russell King had done to move core
runtime PM handling into the bus. Due to that commit, "spi/pl022: fix
spi-pl022 pm enable at probe" was merged to fix part of those issues.
Instead of adding another fix, let's clean up and revert everything
back to when it was already fine.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Revert "spi/pl022: enable runtime PM"
Conflicts:
drivers/spi/spi-pl022.c
This commit allow to put pins in IDLE state in
runtime_suspend and in SLEEP state in suspend, corresponding
to defined semantics in <linux/pinctrl/pinctrl-state.h>.
To do this, just add a boolean parameter runtime
to pl022_resume_resources/pl022_suspend_resources which
indicates if it's called from PM_RUNTIME callbacks or not.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To be able to deactivate resourses in suspend, the resourses must
first be surely active. This is done with a pm_runtime_get_sync.
Once the resourses are restored to active state again in resume,
the runtime pm usage count can be decreased with a pm_runtime_put.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In probe pm_runtime_put_autosuspend has the same effect as doing
pm_runtime_put. This due to upper layer in driver core is preventing
the device from being runtime suspended by a pm_runtime_get*.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This reverts commit 6887237cd7.
Commit "spi/pl022: enable runtime PM" introduced runtime PM issues.
Due to that commit, "spi/pl022: fix spi-pl022 pm enable at probe"
was merged to fix part of those issues.
Instead of adding another fix, let's clean up and revert everything
back to when it was already fine.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This factors out the resource handling in runtime
suspend/resume and also calls it from the ordinary suspend
and resume hooks.
The semantics require that ordinary PM op suspend is called
with runtime PM in resumed mode, so that ordinary suspend
can assume that it will e.g. decrease the clock reference
counter to 0, runtime resume having previously increased it
to 1.
Cc: Vipul Kumar Samar <vipulkumar.samar@st.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This switches the PL022 SPI driver to use devm_* managed resources
for IRQ, clocks, ioremap and GPIO. Prior to this, the GPIOs would
even leak.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Even with devicetree support, we needed platform data to provide some data,
leading to mixed device tree and platform data. This patch makes it possible to
provide all that information via device tree. Now, the data must be provided
via platform data _or_ device tree completely.
Only in case of DMA where a callback specification is necessary (dma_filter()),
platform data is the only option.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Amend the PL022 pin controller to optionally take a pin control
handle and set the state of the pins to "default" on boot and
runtime resume, and to "sleep" at runtime suspend. This way we
will dynamically save power on the SPI busses, for example some
electronic designs may be able to ground the pins when unused
instead of pull-up. Some pin controllers may want to set the
pins as wake-up sources when sleeping.
Effect on platforms using the PL022 driver:
- If the platform does not use pin control - no semantic effect,
the pinctrl stubs will kick in and resolve the situation.
- Platforms using this driver and have pin control but no
function defined for the PL022 need to either supply a
"default" function in their map or enable pinctrl dummies
so the driver is satisfied.
- Platforms using this driver with hogs for setting up the PL022
pin control - stop using hogs to take the pl022 pin control
handle, let the driver handle this.
I'be looked at some platforms that may be affected:
- SPEAr: appears to define the proper functions in their device
trees and not hogging them, so things should be smooth, the
driver will simply start to take its pins.
- Ux500: the proper function is defined and will be taken properly
by the driver. New sleep states introduced by a separate patch to
ux500 but no regression, since the default state is sufficient.
- U300: old hog deleted as part of this patch.
- LPC32xx: does not appear to be using pinctrl.
- ARM Integrator IMPD1, RealView & Versatile: does not use pinctrl.
Tested-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
