drivers/char/pc8736x_gpio.c:192: warning: #pc8736x_gpio_set_high# defined but not used
drivers/char/pc8736x_gpio.c:197: warning: #pc8736x_gpio_set_low# defined but not used
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch makes a needlessly global variable static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The uninitialised pmu_backlight_lock causes the current Fedora test kernel
(which has spinlock debugging enabled) to panic on suspend.
This is suboptimal, so I fixed it.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Michael Hanselmann <linux-kernel@hansmi.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
FIFOCTL_RXERR and FIFOCTL_TXERR are undocumented bits, according to the
Sigmatel datasheet. We should thus not take any assumption on their values
and semantics.
Problem spotted by andrzej zaborowski <balrogg@gmail.com>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch detects the smsc-ircc chipset on the nx1000
(including nx7000 and nx7010) and the nx5000 HP/Compaq laptop series.
Patch from "Linus Walleij (LD/EAB)" <linus.walleij@ericsson.com>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to NatSemi datasheet, the configuration base address for the PC8738x
family is 0x2e or 0x164. 0x0 doesn't appear in any datasheet.
Patch from Lamarque Vieira Souza <lamarque@gmail.com>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The loopback device status structure is a singleton and doesn't
need to be allocated. Add ethtool_ops hooks to show checksum always on,
and make ethtool_ops const.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the inclusion of the stir421x code, we now need to select FW_LOADER
whenever we try to build the irda-usb code.
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
PPPoE must advertise the underlying device's MTU via the ppp channel
descriptor structure, as multilink functionality depends on it.
Signed-off-by: Michal Ostrowski <mostrows@earthlink.net>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the new 5709 device. This is a new 10/100 Mbps chip.
The mailbox access and firmware interface are quite different from
all other tg3 chips.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put the firmware polling logic into a separate function. This makes
the code cleaner.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHY related fixes:
1. Fix Serdes WoL.
2. Fix loopback test on 10/100 only devices.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change to a different ASF heartbeat message code to improve
reliability.
There were some reports of unintended resets on real time kernels
where the timer may be slow and cause the heartbeat to be late.
Netpoll will also have the same problem because the timer irq will
be unavailable.
Using the new heartbeat code, the ASF firmware will also check the
ring condition before resetting the chip when the heartbeat is
expiring.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve 5704S autoneg logic by using a serdes_counter field to keep
track of the transient states. This eliminates a 200 msec busy
loop in the code. Autoneg will take its course without the driver
busy waiting for it to finish.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans up the Bluetooth HCI UART driver a bit.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the vendor and product id of the Canycon CN-BTU1
dongle and sets a flag to send HCI_Reset as the first command.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch assigns the next free HCI device identifier to Bluetooth
devices based on the SDIO interface.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch is an attempt to cleanup the drivers source code to make all
Bluetooth drivers look more unique.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
argument and inferred net-endian variables in callers annotated.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
inet_confirm_addr(), inet_ifa_byprefix(), ip_dev_find(), inet_make_mask() and
inet_ifa_match() annotated, along with inferred net-endian variables
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
ifa_local, ifa_address, ifa_mask, ifa_broadcast and ifa_anycast are
net-endian. Annotated them and variables that are inferred to be
net-endian.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Net devices should depend on NETDEVICES, so revert part of
Paolo's previous patch.
See http://marc.theaimsgroup.com/?l=linux-kernel&m=115566326218740&w=2
for history.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thanks to Andrew for the original patch for this.
I need to upgrade my version of gcc to catch these things...
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Strictly speaking, the Valid bit in SCSI sense data is supposed to
be set only when the Information field contains a valid number. This
patch (as793) turns off the Valid bit when the Information field
hasn't been set.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as791b) fixes things up to avoid compiler warnings or
errors when CONFIG_USB_SUSPEND or CONFIG_PM isn't set.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as790b) adds "autostop" support to ohci-hcd: the driver
will automatically stop the host controller when no devices have been
connected for at least one second. This feature is useful when the
USB autosuspend facility isn't available, such as when
CONFIG_USB_SUSPEND hasn't been set.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The autosuspend technique used by ohci-hcd doesn't mesh well with the
newer USB core autosuspend code. This patch (as789) removes ohci-hcd's
autosuspend support. Now the driver will be usable, but it won't
automatically go into a low-power state when no devices are connected.
That's for a later patch.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Originally I didn't think any host controller driver would ever use
interrupts and polling at the same time, but it turns out ohci-hcd wants
to do exactly that. This patch (as788) makes it possible.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as758) fixes the "warn-unused-result" messages in dummy-hcd.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as787) creates a new workqueue thread to handle delayed
USB autosuspend requests. Previously the code used keventd. However
it turns out that the hub driver's suspend routine calls
flush_scheduled_work(), making it a poor candidate for running in
keventd (the call immediately deadlocks). The solution is to use a
new thread instead of keventd.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB Storage: this patch adds support for Sony Ericsson P990i
Signed-off-by: Jan Mate <mate@fiit.stuba.sk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes kerneldoc errors on usb/core/driver.c, which occured in 2.6.18-rc6-mm2
gregkh-usb-usbcore-add-autosuspend-autoresume-infrastructure.patch
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
During Installation the host tries to enumerate the keyboard/mouse
dongle for the Raritan KVM.At this time timeouts have been observed
Adding the Raritan KVM USB dongle to the blacklist fixes this issue.
Signed-off-by: Raghavendra Biligiri <Raghavendra_Biligiri@Dell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We want to avoid legacy APIs like pci_find_slot().
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Implementations assume the buffer is at least 4 byte aligned.
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We have a couple of these USB-Serial converters around; they're slightly
different from the 2104 models in that they can handle 500Kb/sec over RS422.
The existing ftdi driver seems to work just fine if we add in the
appropriate IDs.
Patch is against 2.6.17.6, but should apply cleanly to pretty much
anything recent.
From: Justin Carlson <justinca@qatar.cmu.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
New phidget interface kits (type 8/8/8) reset their outputs if they
haven't received a set report for 2 seconds.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for three OpenPort ECU data cables from Tactrix
Inc. to the ftdi_sio driver's device ID table. One of the PIDs was
supplied by Donour Sizemore on the ftdi-usb-sio-devel mailing list. The
other two were added by myself after examining the Windows driver software.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Address http://bugzilla.kernel.org/show_bug.cgi?id=7126
Attempting to read the ethernet ID directly from the eeprom somehow
confuses ADM8515. Subsequent read requests to either the eeprom or the MII
fail as well. Didn't dig much deeper, though. For example ADM8513 does
not experience this problem.
I used the fact that at power up the device is reading its ID automatically
(not true for older Pegasus based devices) and put it in the Ethernet ID
registers. So now the driver uses get_registers() instead of
read_eprom_word() if the device is Pegasus_II based one. Tested it with
all (Pegasus and Pegasus_II) gadgets i have and everything seems ok.
Cc: <jogeedaklown@yahoo.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as794) adds an unusual_devs entry for the Nokia E60.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this adds a new id to the kaweth driver.
Please apply.
Signed-Off-By: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
hwmon: Remove Yuan Mu's address
Yuan Mu no longer works at Winbond.
I wish to publicly thank Yuan for his help with Winbond hardware
monitoring chips support during the past 10 months.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
hwmon: Fix unchecked return status, SMSC chips
Fix up 2 more hwmon drivers so that they no longer ignore return
status from device_create_file().
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
hwmon: Fix unchecked return status, batch 6
Fix up 5 more hwmon drivers so that they no longer ignore return status
from device_create_file().
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
w83792d: Fix unchecked return status
Fix the w83792d driver. Add error checking to device_create_file
and also care to destroy the files upon exit.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
w83l785ts: Fix unchecked return status
Fix the w83l785ts driver. Add error checking to device_create_file
and also care to destroy the files upon exit.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
w83781d: Fix unchecked return status
Add 2 attr-file groups (for base and model-specific attrs respectively),
create the base group with single call to sysfs_create_group,
check the return code on individual calls to device_create_file for each
of the model-specific attr-files.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
vt8231: Fix unchecked return status
Check the return status from device_create_file() and also use
the newer and cleaner sysfs creation functions.
Signed-off-by: Roger Lucas <roger@planbit.co.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
hwmon: Fix unchecked return status, batch 5
Fix up some hwmon drivers so that they no longer ignore return status
from device_create_file().
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
hwmon: Fix unchecked return status, batch 4
Fix up some hwmon drivers so that they no longer ignore return status
from device_create_file().
Note: f71805f actually checked the status from device_create_file
already. However it did not remove the files on device destruction.
It was also an opportunity to use sysfs_create/remove_group instead
of hand-made loops. This makes the changes much more important but
I think the result is worth it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
hwmon: Fix unchecked return status, batch 3
Fix up some hwmon drivers so that they no longer ignore return status
from device_create_file().
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
hwmon: Fix unchecked return status, batch 2
Fix up some hwmon drivers so that they no longer ignore return status
from device_create_file().
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
w83627ehf: Fix unchecked return status
Fix: check return value from device_create_file()
Fix: call device_remove_file() on error and module unload
Fix: call hwmon_device_register() after device_create_file() to eliminate race
Signed-off-by: David Hubbard <david.c.hubbard@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pc87360: Check for error on sysfs files creation
Use sysfs_create_group() for 2 sensor-types which are chip-model
invariant, i.e. all-or-nothing attribute groups.
Other 2 groups vary too much due to configuration, etc, so we keep the
loops of device_create_file(), but now check their returns.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pc87360: Delete sysfs files on device deletion
Add 4 explicit attribute groups for the 5 sensor types:
voltage (in), therm, temp, and fan & pwm (together in one group).
Use sysfs_remove_group() to drop them, but keeps the existing
startup code, which calls device_create_file in loops.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pc87360: Move some code around
Moves code for get-set-decl tuples for 3 items: cpu0_vid, vrm, alarms_in
up, to just after the get-set-decl tuple for voltages.
These items are already 'activated' together with the rest of the
voltage attributes, so the move tightens the grouping that's made
explicit in next patch.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
hwmon: Fix unchecked return status, batch 1
Fix up some hwmon drivers so that they no longer ignore return status
from device_create_file().
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
hwmon: New driver for the VIA VT1211
This is a new driver for the VIA VT1211 Super-IO chip. It is a rewrite
of the existing vt1211 driver (by Mark D. Studebaker and Lars Ekman)
which has been around for a while but never made it into the main
kernel tree.
It is implemented as a platform driver and therefore requires
lm_sensors 2.10.1 to function properly.
Signed-off-by: Juerg Haefliger <juergh@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
w83791d: Documentation update
The alarm bits and the beep enable bits are in different positions in
the hardware. Document the problem and leave it to the user-space code
to handle the situation. When this driver is updated to the standardized
sysfs alarm/beep methodology, this won't be a problem.
This is a documentation only change.
Signed-off by: Charles Spirakis <bezaur@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
hwmon: Add individual alarm files to 4 drivers
Add individual sysfs files for all f71805f, lm63, lm83 and lm90 alarm
and fault conditions. This is a requirement for the planned
chip-independent libsensors. Almost all other hwmon drivers will need
the same improvement.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
hwmon: Make a dozen drivers no more experimental
Remove the EXPERIMENTAL tag from a dozen hardware monitoring drivers.
They are in the tree for quite a long time, so we would know by now if
they were causing trouble.
Also make it clearer that the VT8231 is a VIA chip.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch contains rudimentary suspend / resume support for the uguru,
this protects the uguru and the driver against suspend / resume cycles,
so there is no reason to unload the driver in your suspend / resume
scripts.
Only include suspend / resume functions when CONFIG_PM is set.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Let the k8temp driver load automatically.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the temperature sensor(s) found in AMD K8 CPUs.
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
it87: Copyright update
I think my contributions to the it87 driver over the past two
years qualify me as a co-author of this driver.
Also drop old comments of dubious usefulness.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
it87: Overwrite broken default limits
Some IT8716F chips where seen with unreasonable defaults for low
voltage and high temperature limits. Overwrite them with sane defaults
so as to not generate meaningless alarms.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
it87: Add support for the IT8718F
The IT8718F is a Super-I/O chip with integrated hardware monitoring
functions. It is very similar to the IT8716F, so adding support to the
it87 driver was pretty straightforward. The most significant difference
is that the IT8718F has up to 8 VID pins, instead of 6 for the older
chips.
For the IT8718F, the VID value can only be read from Super-I/O space.
Userspace support is already in lm_sensors SVN (to be soon released
as 2.10.1.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
it87: Cleanup set_fan_div
We only change one fan clock divider at a time, so there is only one
fan min which needs to be saved and restored.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
it87: Prevent overflow on fan clock divider write
The highest possible clock divider for fan1 and fan2 is 128.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
it87: No sysfs files for disabled fans
Only create the fan attributes for enabled fan tachometers. Some
motherboards have a nice BIOS which only enables the fan inputs which
are wired to a fan header on the board. This makes the configuration
easier for the user.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
it87: Add support for the IT8716F
The IT8716F is a Super-I/O chip with integrated hardware monitoring
functions. It is very similar to the IT8712F, so adding support to the
it87 driver was pretty straightforward. The most significant change here
is that the IT8716F has 16-bit fan speed counters, so the user no more
needs to tweak the fan clock dividers to get the best readings.
Userspace support is already in lm_sensors SVN (to be soon released
as 2.10.1.)
Thanks to Stian Oksavik, Olivier Nicolas, Prakash Punnoor and
Juergen Kilb for testing the early versions of this patch.
Thanks also to ITE for providing datasheets and answering my questions.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
smsc47m1: dev_warn fix
We can't use dev_warn on an i2c client before it is attached.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
vid_to_reg() can return -1 and char can be unsigned.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds long-awaited support for automatic fan modes. Based on
the work of Yuan Mu from Winbond, I finished the support with the great
help of David Hubbard.
Signed-off-by: Yuan Mu <Ymu@Winbond.com.tw>
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: David Hubbard <david.c.hubbard@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-mmc:
[MMC] Don't check READY_FOR_DATA when reading
[MMC] MMC_CAP_BYTEBLOCK flag for non-log2 block sizes capable hosts
[MMC] Add multi block-write capability
[MMC] Remove data->blksz_bits member
[MMC] Convert mmci to use data->blksz rather than data->blksz_bits
The resize CQ function changes the memory used to store the queue.
Other routines need to honor the lock before accessing the pointer
to the queue and verify that the head and tail are in range.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This change moves around port assignment so that it happens before any
memory is allocated. This allows memory to be allocated on an appropriate
CPU, which improves performance for users of /dev/ipath.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The EEPROM is read via programmable I/O pins. When the driver
is compiled -Os, the CPU can speculatively read the I/O
value before it is valid. This patch fixes the problem.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We can sometimes trigger parity errors due to processor speculative
reads to our write-combined memory (mostly seen on Woodcrest). Add a
stats counter for these.
Factored out the sendbuffererror buffer cancellation code so it can be
used in the new handling; suppress likely subsequent error messages if
within two jiffies of the cancellation.
Also restore 2 dropped TXE lines on hwe_bitsextant noticed while
debugging.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The system must be powercycled to clear a HT CRC error; reloading the
driver is not enough.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We were passing 0 for base and length, which worked on older kernels,
but it doesn't seem to any longer.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If the receiver goes into the error state, we need to flush the
posted receive WQEs.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Prior to this change, the driver was not able to support a HT and PCIE
card simultaneously present in the same machine.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fixed mismatch in linkstate/trainingstate shifts and masks in the
IPATH_IBSTATE_MASK macro. It kept some linktrainingstates
from being printed correctly in debug; no functionality issue unless
I misread the code.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This is required for IB conformance (spec ch. 9.6.1.5).
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Don't allow a write to the eeprom from ipathfs unless the write is exactly
128 bytes and starts at offset 0.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Respond with an error to the SM if our GUID is 0, and don't allow the
user to set our GUID to 0.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This gives upper-level protocols a chance to unregister while the device
is still usable.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This also entailed a little GPIO-interrupt general cleanup.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This allows multiple userspace processes to share a single hardware
context in a master/slave arrangement. It is backwards binary compatible
with existing userspace.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If the second allocation failed, the first structure allocated in this
routine was not freed.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The sender requests an ACK every 1/2 MB to avoid retransmit timeouts that
were causing MVAPICH mod_bw to fail after a predictable number of sends.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix the description of iSER in Kconfig. It is not accurate.
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
iSER uses the DMA mapping api to map the page holding the
SCSI command data to the HCA DMA address space. When the
command data is not aligned for RDMA, the data is copied
to/from an allocated buffer which in turn is used for
executing this command. The pages associated with the
command must be unmapped before being touched.
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
iSER uses a data transaction object (struct iser_dto) as part
of its IB data descriptors (struct iser_desc) management.
It also uses a hierarchy of connection structures pointing to
each other. A DTO may exist even after the iscsi_iser connection
pointed by it is destroyed (eg one that is bound to a post
receive buffer which was flushed by the IB HW). Hence DTOs need
point to the lowest connection, which is struct iser_conn.
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If the allocation of mr fails, then c2_reg_phys_mr() leaks the
page_list array it allocated earlier.
This was Coverity CID #1413.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Another NULL dereference spotted by the Coverity checker (cid #1395):
In case we can't alloc the vq_req, we goto bail1, where we call
vq_req_free(c2dev, vq_req); which then dereferences vq_req.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Acked-by: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Major cleanup of all s390 inline assemblies. They now have a common
coding style. Quite a few have been shortened, mainly by using register
asm variables. Use of the EX_TABLE macro helps as well. The atomic ops,
bit ops and locking inlines new use the Q-constraint if a newer gcc
is used. That results in slightly better code.
Thanks to Christian Borntraeger for proof reading the changes.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Call init_timer only once fpr tp->timer in tty3270.
Signed-off-by: Jan Glauber <jan.glauber@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This is more preparation for adding support for the new Atmel AT91SAM9
processors.
Changes include:
- Replace AT91_BASE_* with AT91RM9200_BASE_*
- Replace AT91_ID_* with AT91RM9200_ID_*
- ROM, SRAM and UHP address definitions moved to at91rm9200.h.
- The raw AT91_P[ABCD]_* definitions are now depreciated in favour of
the GPIO API.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A driver shouldn't compare to DMA_ERROR_CODE directly, use
pci_dma_mapping_error() instead.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use hardware support for chained receive to break up large frames
into multiple pages. This avoids having to do a mult-page allocation
that can fail on a busy system due to fragmented memory.
For normal size MTU, this code behaves the same.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use the netdevice transmit lock via netif_tx_lock rather than putting
lock in device specific code and using lockless transmit. The code is
cleaner using netif_tx_lock, and the performance is same.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Since a transmit can take several control blocks, the old code waited
until the last control block was marked as done. This code processes
the return values incrementally. This makes slots in the tx ring available
and less chance of getting stuck.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use the ethernet device name when requesting the irq because the
irqbalance daemon looks for the name when deciding policy.
Better to play along with this dubious heuristic.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Workarounds for 88e806x chips from the vendor driver.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use the standard pci capability mechanism to access PCI express error
registers, rather than hard coding the offset. Mask off the PCI express
error from ever occuring on non-PCI express systems.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Look at the registers correctly, when doing gigabit full duplex.
Need to look for link partner result.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make sure all 64-bit quantities are cast to unsigned long long
when printed with "%ll" printk formats.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (48 commits)
[PATCH] bonding: update version number
[PATCH] git-netdev-all: pc300_tty build fix
[PATCH] Make PC300 WAN driver compile again
[PATCH] Modularize generic HDLC
[PATCH] more s2io __iomem annotations
[PATCH] restore __iomem annotations in e1000
[PATCH] 64bit bugs in s2io
[PATCH] bonding: Fix primary selection error at enslavement time
[PATCH] bonding: Don't mangle LACPDUs
[PATCH] bonding: Validate probe replies in ARP monitor
[PATCH] bonding: Don't release slaves when master is admin down
[PATCH] bonding: Add priv_flag to avoid event mishandling
[PATCH] bonding: Handle large hard_header_len
[PATCH] bonding: Remove unneeded NULL test
[PATCH] bonding: Format fix in seq_printf call
[PATCH] bonding: Convert delay value from s16 to int
[PATCH] bonding: Allow bonding to enslave a 10 Gig adapter
Delete unused drivers/net/gt64240eth.h
[PATCH] skge: fiber support
[PATCH] fix possible NULL ptr deref in forcedeth
...
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] Don't use old-EH ->eng_timeout() hook when not needed
[libata] sata_mv: fix oops by filling in missing hook
[libata] One more s/15/ATA_SECONDARY_IRQ/ substitution
[libata] pata_serverworks: fill in ->irq_clear hook
[PATCH] pata_serverworks: correct PCI ID in cable detection table
[PATCH] libata-sff: use our IRQ defines
[PATCH] libata-eh: Remove layering violation and duplication when handling absent ports
[PATCH] libata: tighten rules for legacy dependancies
[PATCH] libata: refuse to register IRQless ports
I neglected to properly update the version number in the recent
patch series; this sets it to something reasonable.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In file included from drivers/net/wan/pc300_tty.c:59:
drivers/net/wan/pc300.h:335: error: field 'pppdev' has incomplete type
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert LOMOMO to use struct device * for GPIOs instead of struct
locomo_dev. This enables access to the GPIOs from code which is not
a locomo device itself (such as audio). Access for gpio 31 is removed
for error handling (no such hardware exists).
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We experimented with more descriptor buffer writebacks and found that
values larger than 8 give HW problems, but 8 is safe and gives us some
improved performance.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Memory allocated for new tx_ring and rx_ring leaks if
e1000_setup_XX_resources() fails.c Also this patch reduces stack usage
(removed tx_new and rx_new) and uses kzalloc instead kmalloc+memset(0)
Signed-off-by: Vasily Averin <vvs@sw.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Several minor issues exist in the low-level device handling code of
e1000. The NVM and EEPROM writing/reading code was updated which fixes
unneeded delays, adds proper eeprom aqcuiring steps and handle shadow
ram and flash access. Minor cosmetic adjustments to the polarity code
adding symbols. PHY reset code mistakenly distinguished between MAC
types instead of PHY types, and was fixes.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
We were plagued by our interrupt handler posting a watchdog event which
could occur when our adapter was going down in case a late packet arrived
just before e1000_down() finished. This caused the watchdog timer to start
after the NIC was down and keep rescheduling it every N seconds. Once
the driver unloaded it would panic.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Manageability is using one more RAR entry than we anticipated earlier
for ICH8.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Add code to display the detected PCI-E bus width.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
When powering down the PHY (if WoL is disabled) we should only check
copper PHY's and handle PCI-E adapters differently.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Several hardware bits were set all over the driver and have been
consolidated into a single function.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Disable jumbo frames for 82573L alltogether and when ASPM is enabled
since the hardware has problems with it. For the NICs that do support
this in the 82573 series we set ERT_2048 to attempt to receive as much
traffic as early as we can.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Several manageability capability detection parts hinted towards
our code being incomplete for PCI-E. According to spec, we do not
want to poke any MANC bits at all.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
With a patch, ethtool can now signify the driver to advertise more
than just a single speed/duplex setting. This allows you to tell the
card to advertise in 10/100 in any speed if you don't have a gigabit
switch for instance.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Add 4 multicast and broadcast hardware counters (rx/tx), and eliminate
as many non-hardware counters as possible.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Unify our shutdown/suspend/resume code and make it similar to e1000:
e1000_shutdown now calls suspend which does the exact same thing on
shutdown except saving PCI config state on suspend. WoL setup code
is now also more simple and works even when CONFIG_PM is not set, which
was previously broken.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
We keep getting requests from people that think that this might be
an exploitable hole where we would overwrite 4 bytes in the netdev
struct if the pci name would exceed 15 characters. In reality this
will never happen but we fix it anyway.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
This update to the copyright header adds the mailinglist, and aligns it
with the kernel licensing as well as remove the offending 'all rights
reserved'.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
In file included from drivers/usb/storage/usb.c:180:
drivers/usb/storage/unusual_devs.h:221: error: 'US_PR_KARMA' undeclared here (not in a function)
drivers/usb/storage/unusual_devs.h:221: error: 'rio_karma_init' undeclared here (not in a function)
Cc: Keith Bennett <keith@mcs.st-and.ac.uk>
Acked-by: Bob Copeland <me@bobcopeland.com>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adapted from an earlier patch by Greg KH <gregkh@suse.de>.
That patch added multiple read urbs and larger transfer buffers to allow
data transfers at full EvDO speed.
This version includes additional device IDs and fixes a memory leak in
the transfer buffer allocation.
Some (maybe all?) of the supported devices present multiple bulk endpoints,
the additional EPs can be used for control and status functions,
This version allocates 3 EPs by default, that can be changed using
the 'endpoints' module parameter.
Tested with Sierra Wireless EM5625 and MC5720 embedded modules.
Device ID (0x0c88, 0x17da) for the Kyocera Wireless KPC650/Passport
was added but is not yet tested.
From: Andy Gay <andy@andynet.net>
Cc: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Somewhere along the line, a variable in a USB-OTG codepath
stopped being used; this removes the relevant compiler warning.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This revamps handling of the hardware "async advance" IRQ, and its watchdog
timer. Basically it dis-entangles that important timeout from the others,
simplifying the associated state and code to make it more robust.
This reportedly improves behavior of EHCI on some systems with VIA chips,
and AFAIK won't affect non-VIA hardware. VIA systems need this code to
recover from silcon bugs whereby the "async advance" IRQ isn't issued.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch(as785) forces the PM core to resume a root hub after a
power loss during system sleep. If the root hub had been suspended
before the system sleep then normally the PM core would not resume it
afterward. Without this resume, various sorts of wakeup events (like
port change events) can get lost.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When ohci-hcd is shutting down (for rmmod or PC-card removal), there is
a window when the device is shut down, HC communication area (->hcca)
is freed, but the core has not called "free_irq" yet. If another device
triggers a shared interrupt in this window, we oops when trying to
access the freed ->hcca.
This patch removes the window by calling free_irq before ->hcca is freed.
The patch is tested at the PC hotplug test rig at Stratus, and with
rmmod by Rafael Wysocki.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The purpose of this patch is to split off the case when a device does
not reply on the lower level (which is reported by HC hardware), and
a case when the device accepted the request, but does not reply at
upper level. This redefinition allows to diagnose issues easier,
without asking the user if the -110 happened "immediately".
The usbmon splits such cases already thanks to its timestamp, but
it's not always available.
I adjusted all drivers which I found affected (by searching for "urb").
Out of tree drivers may suffer a little bit, but I do not expect much
breakage. At worst they may print a few messages.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch removes unneeded casts for the following (void *) pointers:
- struct file: private
- struct urb: context
- struct usb_bus: hcpriv
- return value of kmalloc()
The patch also contains some whitespace cleanup in the relevant areas.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This "u132-hcd" module is one half of the "driver" for
ELAN's U132 which is a USB to CardBus OHCI controller
adapter. This module needs the "ftdi-elan" module in
order to communicate to CardBus OHCI controller inserted
into the U132 adapter.
When the "ftdi-elan" module detects a supported CardBus
OHCI controller in the U132 adapter it loads this "u132-hcd"
module.
Upon a successful device probe() the single workqueue
is started up which does all the processing of commands
from the USB core that implement the host controller.
The workqueue maintains the urb queues and issues commands
via the functions exported by the "ftdi-elan" module. Each
such command will result in a callback.
Note that the "ftdi-elan" module is a USB client driver.
Note that this "u132-hcd" module is a (cut-down OHCI)
host controller.
Thus we have a topology with the parent of a host controller
being a USB client! This really stresses the USB subsystem
semaphore/mutex handling in the module removal.
Signed-off-by: Tony Olech <tony.olech@elandigitalsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This "ftdi-elan" module is one half of the "driver" for
ELAN's Uxxx series adapters which are USB to PCMCIA CardBus
adapters. Currently only the U132 adapter is available and
it's module is called "u132-hcd".
When the USB hot plug subsystem detects a Uxxx series adapter
it should load this module.
Upon a successful device probe() the jtag device file interface
is created and the status workqueue started up.
The jtag device file interface exists for the purpose of
updating the firmware in the Uxxx series adapter, but as
yet it had never been used.
The status workqueue initializes the Uxxx and then sits there
polling the Uxxx until a supported PCMCIA CardBus device is
detected it will start the command and respond workqueues
and then load the module that handles the device. This will
initially be only the u132-hcd module. The status workqueue
then just polls the Uxxx looking for card ejects.
The command and respond workqueues implement a command
sequencer for communicating with the firmware on the other
side of the FTDI chip in the Uxxx. This "ftdi-elan" module
exports some functions to interface with the sequencer.
Note that this module is a USB client driver.
Note that the "u132-hcd" module is a (cut-down OHCI)
host controller.
Thus we have a topology with the parent of a host controller
being a USB client! This really stresses the USB subsystem
semaphore/mutex handling in the module removal.
Signed-off-by: Tony Olech <tony.olech@elandigitalsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch to add support for Alcor Micro Corp. USB 2.0 TO RS-232 converter.
This patch adds VID and PID to pl2303.[ch], adds it to the "HORRIBLE
HACK FOR PL2303" in usb-serial.c and also prevents cdc-acm to claim
driving this device by blacklisting it in hid-core.
Signed-off-by: Johannes Steingraeber <Jo_Stein@web.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is a driver for the PlayStation 2 specific Trance Vibrator
device. The only thing that device can do is vibrate at various speeds.
Signed-off-by: Sam Hocevar <sam@zoy.org>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Luiz Fernando N. Capitulino" <lcapitulino@mandriva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for Ontrak ADU USB devices.
Fixed for printk issues by Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Steven Haigh <netwiz@crc.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix printk format warnings:
drivers/usb/serial/aircable.c:221: warning: format ‘%Zd’ expects type ‘signed size_t’, but argument 4 has type ‘int’
drivers/usb/serial/aircable.c:283: warning: format ‘%Zd’ expects type ‘signed size_t’, but argument 4 has type ‘int’
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add driver for AIRcable USB Bluetooth dongle.
Signed-off-by: Naranjo, Manuel Francisco <naranjo.manuel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When receiving a fatal error from the USB core, e.g. EILSEQ (which can
happen if the polling interval is too short), fail gracefully.
Previously the driver would fill the log with useless error messages
or (more alarmingly) silently spin forever trying to write updated
control information to the device. This change implements a new flag
which if cleared indicates that the driver has failed. The flag will
be set on initialization, cleared on fatal errors, and anything else
that touches the USB port in the driver will abort if the flag is
clear. When the flag is cleared, a message will be logged indicating
that the driver has failed.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix usb core function error return checks to look for negative errno
values, not positive errno values. This bug had rendered those checks
useless. Also remove attempted error recovery on control endpoints
for EPIPE - with control endpoints EPIPE does not indicate a halted
endpoint so trying to recover with usb_clear_halt() is not the correct
action.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rather than directly filling in URB fields, it's safer to use
usb_fill_int_urb(). This improves robustness of the driver; URB
changes in the future will not go uninitialized here. That point not
withstanding, this driver should at least be self-consistent. Either
use usb_fill_int_urb() everywhere or don't bother with it all.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The polling interval for the device can't always be 1msec. If it is
too quick, the device can fail causing a fatal (to the driver) EILSEQ
error from the USB core. The actual correct value is reported by the
device as part of its configuration data, so use that value as the
default. On a DeLorme Earthmate for example, the device reports that
it wants a 6msec interval. As part of this fix, the "interval" module
option has been fixed as well; the device's default can be overridden
by specifying interval=<value> as a module option.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
