Pass it as an argument to all functions. This is requires as newer SPROM
revisions have different lengths.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Packet drop may be caused by various flows, like disconnect
while Tx packets was queued; this should not lead to stopping
of the Tx queue, or all Tx get stalled.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- Introduce common code for Tx/Rx descriptor physical address set/parse
- Fix endianness for address fields
- consistent descriptor naming: '_d' for non-cached memory, 'd' for cached copy
- wil_tx_desc_map now modify cached copy, no need for 'volatile'
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce NAPI for Rx and Tx completion.
This fixes packet reordering that happens when Rx handled right in
the IRQ: netif_rx puts packet in 'percpu' queue, then network stack
fetches packets from 'percpu' queues for processing, with different
pattern of queue switching. As result, network stack see packets
in different order. This causes hard to understand TCP throughput
degradation in about 30min
Complete polling if only one packet was processed - this eliminates
empty polls that would be otherwise done at the end of each burst
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move packet dump to the earliest location where it is known to have
valid data.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If Rx descriptor contains garbage, it is possible to access memory beyond
allocated buffer.
Check this condition and drop Rx if reported length is
unreasonable large
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hardware uses little endian for the Tx/Rx descriptors field 'length',
do appropriate conversions
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Chun-Yeow and Javier Lopez contributed these changes to
make mesh mode use the more similar AP beaconing mode and
queue parameters. Should improve PS performance, interface
concurrency (AP modes can coexist), and beacon interval
stability.
AR9271 (ath9k_htc) mesh interfaces also need to be in AP
operating mode.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Advertise support for management frame protection in hardware.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
More specifically, enable AP-style beaconing on mesh
ifaces and change the hw capabilities to reflect mesh
support.
Coexistence with a virtual STA interface was tested as
working fine.
Signed-off-by: Javier Cardona <javier@cozybit.com>
[rebase, add iface combinations]
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was added during the early conversion of ampdu_action
to a sleeping callback. There is no need to do this - instead,
use the normal mutex that is acquired for all callbacks.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This option has not been enabled by default in any
distribution, has never been enabled in OpenWrt and no developer
has asked for this information in a bug report.
Dumping pages of random values doesn't help debugging,
remove this option (along with the vmalloc() abuse).
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All PCIe devices must support MSIs, make use of them.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only do it after the queues are allocated. This
will allow to use the 'rt2x00dev->bcn->limit'
instead of 'rt2x00dev->ops->bcn->entry_num'.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The beacon data queue is initialized already when
the rt2800_clear_beacon_register() function is called.
Fetch the size of the TXWI descriptor from that
instead of using the winfo_size field of the data
queue descriptor.
The two values are the same, and the use of the
rt2x00dev->bcn->winfo_size value allows us to
get rid of a superfluous pointer dereference.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The RX data queue is initialized already when
the rt2800_usb_enable_radio() function is called.
Fetch the number of the queue entries from that
instead of using the entry_num field of the data
queue descriptor.
The two values are the same, and the use of the
rt2x00dev->rx->limit value allows us to get rid
of a superfluous pointer dereference.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TX data queue is initialized already when
the rt2800pci_txstatus_interrupt() function is
called.
Fetch the number of the queue entries from that
instead of using the entry_num field of the data
queue descriptor.
The two values are the same, and the use of the
rt2x00dev->tx->limit value allows us to get rid
of a superfluous pointer dereference.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TX data queue is initialized already when
the rt61pci_txdone() function is called.
Fetch the number of the queue entries from that
instead of using the entry_num field of the data
queue descriptor.
The two values are the same, and the use of the
rt2x00dev->tx->limit value allows us to get rid
of a superfluous pointer dereference.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TX data queue is initialized already when
the rt2x00lib_probe_hw() function is called.
Fetch the number of the queue entries from that
instead of using the entry_num field of the data
queue descriptor.
The two values are the same, and the use of the
rt2x00dev->tx->limit value allows us to get rid
of a superfluous pointer dereference.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We send direct probe to broadcast address, as some APs do not respond to
unicast PROBE frames when unassociated. Broadcast frames are not acked,
so we can not use that for trigger MLME state machine, but we need to
use old timeout mechanism.
This fixes authentication timed out like below:
[ 1024.671974] wlan6: authenticate with 54:e6:fc:98:63:fe
[ 1024.694125] wlan6: direct probe to 54:e6:fc:98:63:fe (try 1/3)
[ 1024.695450] wlan6: direct probe to 54:e6:fc:98:63:fe (try 2/3)
[ 1024.700586] wlan6: send auth to 54:e6:fc:98:63:fe (try 3/3)
[ 1024.701441] wlan6: authentication with 54:e6:fc:98:63:fe timed out
With fix, we have:
[ 4524.198978] wlan6: authenticate with 54:e6:fc:98:63:fe
[ 4524.220692] wlan6: direct probe to 54:e6:fc:98:63:fe (try 1/3)
[ 4524.421784] wlan6: send auth to 54:e6:fc:98:63:fe (try 2/3)
[ 4524.423272] wlan6: authenticated
[ 4524.423811] wlan6: associate with 54:e6:fc:98:63:fe (try 1/3)
[ 4524.427492] wlan6: RX AssocResp from 54:e6:fc:98:63:fe (capab=0x431 status=0 aid=1)
Cc: stable@vger.kernel.org # 3.9
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The D3 firmware API changed to include a new field, adjust
the driver to it to avoid getting an NMI when configuring.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When different images can (soon) be accessed through this
file, storing the section offset/length on first access to
the file breaks (or needs manual reset). Avoid this by not
storing the offset/length values but using them locally in
the function only. That way, the correct values are always
used.
While at it, correct the check that firmware is loaded.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If RF-kill is asserted while a device is initialized, the
firmware INIT image can now be run to retrieve the NVM
data and register to mac80211 properly. Previously, the
initialisation would fail in this scenario and the driver
wouldn't register with mac80211 at all, making the device
unusable.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some newer devices will be integrated into the platform more
deeply and will not have embedded NVM (EEPROM/OTP). To support
such devices the NVM data must be provided by the platform,
allow loading the data via request_firmware() and then send it
to the device as needed.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These messages aren't really useful, suppress them unless
EEPROM debugging is turned on.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As the new MVM firmware files package the DATA section
first, and debugfs files want to access the DATA and
not INST section, reverse the order here. This is only
relevant for debugfs code that accesses the SRAM DATA
section and uses this constant to access the section.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If NVM parsing fails and returns NULL, we continue in
the code flow and eventually crash accessing the NULL
pointer. Return an error from iwl_nvm_init() if the
parsing failed.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Configure power management in the D3 firmware by sending
the power table command to it when suspending; this uses
some values that are more suitable to a low power state.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
New host-device API provides the ability to set the number
of DTIMs to skip. Add this parameter to the command and set
it (to a sane default value.)
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Generally, the DTIM period is available after a beacon has
been received, and if no beacon has been received enabling
powersave is problematic anyway for synchronisation. Since
some drivers may require the DTIM period for powersave,
don't enable powersave until it becomes available in case
the scan/association managed to not receive a beacon.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously the mesh_auth_id was disabled. Instead set the
correct mesh authentication bit based on the mesh setup.
Signed-off-by: Colleen Twitty <colleen@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Authentication takes place in userspace, but the beacon is
generated in the kernel. Allow userspace to inform the
kernel of the authentication method so the appropriate
mesh config IE can be set prior to beacon generation when
joining the MBSS.
Signed-off-by: Colleen Twitty <colleen@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no real difference between *array and array, but
the former confuses smatch so write it differently. The
generated code is exactly the same.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211 and the Intel drivers all define crypto
constants, move them to ieee80211.h instead.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When an HT AP is advertising channel switch in a beacon, it
doesn't (and shouldn't, according to 802.11-2012 Table 8-20)
include a secondary channel offset element. The only possible
interpretation is that the previous secondary channel offset
remains valid, so use that when switching channel based only
on beacon information.
VHT requires the Wide Bandwidth Channel Switch subelement to
be present in the Channel Switch Wrapper element, so the code
for that is probably ok (see 802.11ac Draft 4, 8.4.2.165.)
Reported-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make kerneldoc content match header file content, no functional
change.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To support auto-loading of wireless modules from netlink users, add module
alias for nl80211 family.
This also adds NL80211_GENL_NAME constant to define the "nl80211" netlink
family name as part of uapi.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add regulatory class for 60GHz band, according
to the last specification.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the counter for non-AMPDU frames to mvm. It is needed
for the drain flow which happens once the ieee80211_sta has
been freed, so keeping it in iwl_mvm_sta which is embed into
ieee80211_sta is not a good idea.
Also, since its purpose it to remove the STA in the fw only
after all the frames for this station have exited the shared
Tx queues, we need to decrement it in the reclaim flow. This
flow can happen after ieee80211_sta has been removed, which
means that we have no iwl_mvm_sta there. So we can't know
what is the vif type. Hence, we know audit these frames for
all the vif types.
In order to avoid spawning sta_drained_wk all the time, we
now check that we are in a flow in which draining might
happen - only when mvmsta is NULL. This is better than
previous code that would spawn sta_drained_wk all the time
in AP mode.
Cc: stable@vger.kernel.org [3.9]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the normal flow first MAC_CONTEXT_CMD for particular interface is
never sent while associated. The exception is fw restart flow when
resuming from suspend when WoWLAN is enabled. In this case successive
"add" and "modify" MAC_CONTEXT_CMD commands may be sent with assoc flag
set what cause FW mal functioning. To prevent this never set assoc flag
in MAC_CONTEXT_CMD with action "add".
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Without this command, the firmware will filter out all the
multicast frames. Let them all in as for now. Later we will
want to optimize this to save power.
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The FW AUX framework does not handle well cases where time events
fail to be scheduled (and as a result issues assert 0x3330). Until
a proper fix is in place, WA this by always setting the scan type to
SCAN_TYPE_FORCED.
Cc: stable@vger.kernel.org
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code sending the current WoWLAN TCP wakeup settings in
nl80211_send_wowlan_tcp() is not closing the nested attribute,
thus causing the parser to get confused on the receiver side
in userspace (iw). Fix this.
Cc: stable@vger.kernel.org [3.9]
Reported-by: Deepak Arora <deepakx.arora@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
