arm will pad even between u8's, so mark the structs/unions
packed. Fixes a build bug on arm due to BUILD_BUG_ON tests
in the code.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the value read from HERMES_RID_TXQUEUEEMPTY becomes 0 after exactly
100 readings, we wrongly consider it a timeout. Rewrite the clever
while loop as a for loop that does the right thing and looks simpler.
Reported by Juha Leppanen <juha_motorsportcom@luukku.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I forgot that iwl3945 registration is separate from iwlagn.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The assertion of the lock-bit in the hardware register is unreliable,
because there are devices with quirks that will randomly set the bit.
Do the assertion in software, only.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a new device to ar9170usb.
Reported-by: Mike Kershaw/Dragorn <dragorn@kismetwireless.net>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Code was clearly wrong, plus callers expect the mode change to happen as
soon as possible, not dropped on the floor until the next time some
other config value changes and a commit happens.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add USB device ID for OQO 01+'s internal wireless LAN
An OQO employee mentions the chip's true identity here:-
ftp://ftp.oqo.com/unsupported/linux/OQOLinux.html
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Acked-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't lead memory when receive errors
Signed-off-by: Philip Rakity <prakity@yahoo.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the bug that the driver tries to continue to
connect(associate) to AP even if gelic_wl_do_{wpa,wep}_setup() fails,
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the following waring:
> ------------[ cut here ]------------
>WARNING: at kernel/softirq.c:138 local_bh_enable+0x54/0xbc()
>Modules linked in: p54spi
>[<c0034ff8>] (dump_stack+0x0/0x14)
>[<c005b1a4>] (warn_on_slowpath+0x0/0x68)
>[<c00604c8>] (local_bh_enable+0x0/0xbc)
>[<bf000000>] (p54spi_op_tx+0x0/0x4c [p54spi])
>[<c01a4d34>] (p54_sta_unlock+0x0/0x78)
p54spi_op_tx needs to be called from different locking contexts.
Therefore we have to protect the linked list with irqsave spinlocks.
Reported-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I'm very sorry, as this change belongs to the other patch:
"[PATCH] p54: fix SoftLED compile dependencies".
however I must have somehow lost "git add" for that file.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The RX buffer poison needs to be refreshed, if we recycle an RX buffer,
because it might be (partially) overwritten by some DMA operations.
Cc: stable@kernel.org
Cc: Francesco Gringoli <francesco.gringoli@ing.unibs.it>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds poisoning and sanity checking to the RX DMA buffers.
This is used for protection against buggy hardware/firmware that raises
RX interrupts without doing an actual DMA transfer.
This mechanism protects against rare "bad packets" (due to uninitialized skb data)
and rare kernel crashes due to uninitialized RX headers.
The poison is selected to not match on valid frames and to be cheap for checking.
The poison check mechanism _might_ trigger incorrectly, if we are voluntarily
receiving frames with bad PLCP headers. However, this is nonfatal, because the
chance of such a match is basically zero and in case it happens it just results
in dropping the packet.
Bad-PLCP RX defaults to off, and you should leave it off unless you want to listen
to the latest news broadcasted by your microwave oven.
This patch also moves the initialization of the RX-header "length" field in front of
the mapping of the DMA buffer. The CPU should not touch the buffer after we mapped it.
Cc: stable@kernel.org
Reported-by: Francesco Gringoli <francesco.gringoli@ing.unibs.it>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit a390d1f3 ("phylib: convert state_queue work to
delayed_work") missed converting 'expires' value to 'delay' value.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent ixgbe from putting the adapter into D3 during shutdown except when
we're going to power off the system, since doing that may generally cause
problems with kexec to happen (such problems were observed for igb and
forcedeth). For this purpose seperate ixgbe_shutdown() from ixgbe_suspend()
and use the appropriate PCI PM callbacks in both of them.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent e1000e from putting the adapter into D3 during shutdown except when
we're going to power off the system, since doing that may generally cause
problems with kexec to happen (such problems were observed for igb and
forcedeth). For this purpose seperate e1000e_shutdown() from e1000e_suspend()
and use the appropriate PCI PM callbacks in both of them.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent e1000 from putting the adapter into D3 during shutdown except when
we're going to power off the system, since doing that may generally cause
problems with kexec to happen (such problems were observed for igb and
forcedeth). For this purpose seperate e1000_shutdown() from e1000_suspend()
and use the appropriate PCI PM callbacks in both of them.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds clock framework support to the rtc-sh driver. With this in
place, platforms can default to leaving the clock disabled rather than
placing it in the always enabled state.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The use of disable_irq inside the handler for the interrupt being
disabled has always been dangerous. disable_irq should wait for that
handler to complete before returning -> deadlock.
For some reason this wasn't actually the case until 3aa551c9b was merged
but since this time, the ads7846 driver has deadlocked the system on
first interrupt.
Convert the driver to use the handler-safe _nosync variant.
Signed-off-by: Ben Nizette <bn@niasdigital.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] boot cputime accounting
[S390] add read_persistent_clock
[S390] cpu hotplug and accounting values
[S390] fix idle time accounting
[S390] smp: fix cpu_possible_map initialization
[S390] dasd: fix idaw boundary checking for track based ccw
[S390] dasd: Use the new async framework for autoonlining.
[S390] qdio: remove dead timeout handler
[S390] appldata: Use new mod_virt_timer_periodic() function.
[S390] extend virtual timer interface by mod_virt_timer_periodic
[S390] stp synchronization retry timer
[S390] call nmi_enter/nmi_exit on machine checks
[S390] wire up preadv/pwritev system calls
[S390] s390: move machine flags to lowcore
The loop body was never executed, because the condition is
always false. Convert to for with more obvious condition.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
dev is leftover from b0ee0d3eb3
(Input: pc110pad - use no_pci_devices()).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch removes depreciated IRQF_SAMPLE_RANDOM flags from
ad7877 and ad7879 touchscreen drivers.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
PEN_{UP/DOWN} events are expected to be available soon after stopping
TSI auto measurement, but this is found not always be true. Work around
this by adding delay and simulating such an event (according to pen down
status bit).
Signed-off-by: Bin Yang <bin.yang@marvell.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Bin did a lot of work on this driver, without his help, this driver
will not be possible.
Signed-off-by: Bin Yang <bin.yang@marvell.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The commit 6902c0bead that moved
driver registration out of kgameportd thread was incomplete and
did not add the code necessary to actually attach driver to
already registered devices, rectify that.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fix this build error when CONFIG_SERIO is not set
hp_sdc_rtc.c:691: undefined reference to `hp_sdc_request_timer_irq'
and so on..
"select should be used with care. select will force
a symbol to a value without visiting the dependencies."
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
brd is missing a flush_dcache_page. On 2nd thoughts, perhaps it is the
pagecache's responsibility to flush user virtual aliases (the driver of
course should flush kernel virtual mappings)... but anyway, there
already exists cache flushing for one direction of transfer, so we
should add the other.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
brd is always ordered (not that it matters, as it is defined not to
survive when the system goes down). So tell the block layer it is
ordered, which might be of help with testing filesystems.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Add LRO alignment initially committed in
621544eb8c ("[LRO]: fix lro_gen_skb()
alignment") and removed in 0dcffac1a3
("myri10ge: add multislices support") during conversion to
multi-slice.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With 2.6.30-rc1 on SMDK6410 I experience a soft lockup on bootup when
the Samsung serial driver attempts to disable the transmit interrupt
from within the transmit interrupt handler: it calls disable_irq()
which locks up due to attempting to synchronise with the running handler.
Fix this by using disable_irq_nosync().
Also make the same change in the recieve path.
Backtrace:
[<c002a914>] (__irq_svc+0x34/0x80) from [<c00696c0>] (synchr)
[<c00696c0>] (synchronize_irq+0xc/0xcc) from [<c018d434>] (s)
[<c018d434>] (s3c24xx_serial_stop_tx+0x1c/0x3c) from [<c018d)
[<c018d54c>] (s3c24xx_serial_tx_chars+0xf8/0x104) from [<c00)
[<c0068bcc>] (handle_IRQ_event+0x74/0x118) from [<c006ab04>])
[<c006ab04>] (handle_level_irq+0x100/0x118) from [<c00349c4>)
[<c00349c4>] (s3c_irq_demux_uart+0x94/0xc4) from [<c002a050>)
[<c002a050>] (_text+0x50/0x6c) from [<c002a914>] (__irq_svc+)
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It's used by DM and MD and generally useful, so move the bio list
helpers into bio.h.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Move the update of real_num_tx_queues from
ixgbe_acquire_msix_vectors() to ixgbe_set_num_queues(), to ensure it
be always in sync with num_tx_queues.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't do the num_tx_queues based masking on calculating tx queue
index.
1) num_tx_queues is not always power-of-2, because it also depends on
the online cpu numbers. So the masking could be a performance bug
on a 6 cpu system.
2) queue_mapping will be limited by real_num_tx_queues=num_tx_queues
in the generic netdev function set_cur_queue_map(). So the bound
limiting here is not necessary.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
falcon_sim_phy_event() used EFX_OWORD_FIELD, which operates on
bitfields in 128-bit values, on an event, which is a 64-bit value.
This should be harmless - these macros always use little-endian
ordering, so it would read and write back the following 8 bytes
unchanged - but it is obviously wrong.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sfc could call netif_napi_add() multiple times for the same
napi_struct, corrupting the list of napi_structs for the associated
device and leading to a busy-loop on device removal. Move the call to
netif_napi_add() and add a call to netif_napi_del() in the obvious
places.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove debug printk I accidently left in as part of commit:
commit 6146b1a4da
Author: Jay Vosburgh <fubar@us.ibm.com>
Date: Tue Nov 4 17:51:15 2008 -0800
bonding: Fix ALB mode to balance traffic on VLANs
Reported by Duncan Gibb <duncan.gibb@siriusit.co.uk>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e1000/e1000e compile report a possible unused variable, fix
that for now. Shortly after this a small refactor and bug
fix will follow in the same code.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: Subrata Modak <subrata@linux.vnet.ibm.com>
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BUG_ON(skge->tx_ring.to_use != skge->tx_ring.to_clean) in skge_up()
was sometimes observed when setting MTU.
skge_down() disables the TX queue, but then reenables it by mistake via
skge_tx_clean().
Fix it by moving the waking of the queue from skge_tx_clean() to the
other caller. And to make sure start_xmit is not in progress on another
CPU, skge_down() should call netif_tx_disable().
The bug was reported to me by Jiri Jilek whose Debian system sometimes
failed to boot. He tested the patch and the bug did not happen anymore.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'drm-intel-next' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: fix scheduling while holding the new active list spinlock
drm/i915: Allow tiling of objects with bit 17 swizzling by the CPU.
drm/i915: Correctly set the write flag for get_user_pages in pread.
drm/i915: Fix use of uninitialized var in 40a5f0de
drm/i915: indicate framebuffer restore key in SysRq help message
drm/i915: sync hdmi detection by hdmi identifier with 2D
drm/i915: Fix a mismerge of the IGD patch (new .find_pll hooks missed)
drm/i915: Implement batch and ring buffer dumping
regression caused by commit 5e118f4139:
i915_gem_object_move_to_inactive() should be called in task context,
as it calls fput();
Signed-off-by: Shaohua Li<shaohua.li@intel.com>
[anholt: Add more detail to the comment about the lock break that's added]
Signed-off-by: Eric Anholt <eric@anholt.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Add in PCI bus for DMA API debugging.
sh: Pre-allocate a reasonable number of DMA debug entries.
sh: sh7786: modify usb setup timeout judgment bug.
MAINTAINERS: Update sh architecture file patterns.
sh: ap325: use edge control for ov772x camera
sh: Plug in support for ARCH=sh64 using sh SRCARCH.
sh: urquell: Fix up address mapping in board comments.
sh: Add support for DMA API debugging.
sh: Provide cpumask_of_pcibus() to fix NUMA build.
sh: urquell: Add board comment
sh: wire up sys_preadv/sys_pwritev() syscalls.
sh: sh7785lcr: fix PCI address map for 32-bit mode
sh: intc: Added resume from hibernation support to the intc
Fix lpfc_parse_bg_err()'s use of do_div(). It should be passing a 64-bit
variable as the first parameter. However, since it's only using a 32-bit
variable, it doesn't need to use do_div() at all, but can instead use the
division operator.
This deals with the following warnings:
CC drivers/scsi/lpfc/lpfc_scsi.o
drivers/scsi/lpfc/lpfc_scsi.c: In function 'lpfc_parse_bg_err':
drivers/scsi/lpfc/lpfc_scsi.c:1397: warning: comparison of distinct pointer types lacks a cast
drivers/scsi/lpfc/lpfc_scsi.c:1397: warning: right shift count >= width of type
drivers/scsi/lpfc/lpfc_scsi.c:1397: warning: passing argument 1 of '__div64_32' from incompatible pointer type
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the ti-usb adapter returns an zero data length frame (which happens)
then we leak a kref. Found by Christoph Mair <christoph.mair@gmail.com>
who proposed a patch. The patch here is different as Christoph's patch
didn't work for the case where tty = NULL and data arrived but Christoph
did all the hard work chasing it down.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ACM sets the low latency flag but calls the flip buffer routines from
IRQ context which isn't permitted (and as of 2.6.29 causes a warning
hence this one was caught)
Fortunatelt ACM doesn't need to set this flag in the first place as it
only set it to work around problems in ancient (pre tty flip rewrite)
kernels.
Reported-by: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A ccw command that reads or writes several records at once will
usually transfer more data then fits into one page and needs to
address memory areas using a list of indirect data address words
(idaw). All but the first of these areas must start on a 4KB or 2KB
block boundary (depending on the idaw format).
A check for this restriction was missing and has been added with
this patch.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The dasd driver can automatically online detected dasds, which
especially important for finding the root device. Currently,
it will wait for each online operation to finish individually,
which may take long if many dasds need to be onlined. When using
the new async framework, these onlining operations can run in
parallel and presence of the root device is ensured by the fact
that prepare_namespace() waits for all async threads to finish.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The QDIO ccw devices are started by ccw_device_start so no timeout
can occur for the interrupt handler. Remove the dead code.
In case of an I/O error set the device state to error and wake up
a possibly running qdio_shutdown waiter.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When I made the tun driver use non-linear packets as the preferred
option, it broke non-GSO users because they would end up allocating
a completely non-linear packet, which triggers a crash when we call
eth_type_trans.
This patch reverts non-GSO users to using linear packets and adds
a check to ensure that GSO users can't cause crashes in the same
way.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sync_completed file reports how much of a resync (or recovery or
reshape) has been completed.
However due to the possibility of out-of-order completion of writes,
it is not certain to be accurate.
We have an internal value - mddev->curr_resync_completed - which is an
accurate value (though it might not always be quite so uptodate).
So:
- make curr_resync_completed be uptodate a little more often,
particularly when raid5 reshape updates status in the metadata
- report curr_resync_completed in the sysfs file
- allow poll/select to report all updates to md/sync_completed.
This makes sync_completed completed usable by any external metadata
handler that wants to record this status information in its metadata.
Signed-off-by: NeilBrown <neilb@suse.de>
When adding devices to an active array via sysfs, there is currently
no way to mark a device as 'in-sync' which is useful when
incrementally assembling an array.
So add that option.
Signed-off-by: NeilBrown <neilb@suse.de>
- update inclusion guard and make sure it covers the whole file
- remove superflous #ifdef CONFIG_BLOCK
- make sure all required headers are included so that new users aren't
required to include others before
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: NeilBrown <neilb@suse.de>
This patch fixes the default value of pause auto-negotiation supported
by PCS.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-rc1/xen/core' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
xen: add FIX_TEXT_POKE to fixmap
xen: honour VCPU availability on boot
xen: clean up gate trap/interrupt constants
xen: set _PAGE_NX in __supported_pte_mask before pagetable construction
xen: resume interrupts before system devices.
xen/mmu: weaken flush_tlb_other test
xen/mmu: some early pagetable cleanups
Xen: Add virt_to_pfn helper function
x86-64: remove PGE from must-have feature list
xen: mask XSAVE from cpuid
NULL noise: arch/x86/xen/smp.c
xen: remove xen_load_gdt debug
xen: make xen_load_gdt simpler
xen: clean up xen_load_gdt
xen: split construction of p2m mfn tables from registration
xen: separate p2m allocation from setting
xen: disable preempt for leave_lazy_mmu
The edac-core driver includes code which assumes that the work_struct
which is included in every delayed_work is the first member of that
structure. This is currently the case but might change in the future, so
use to_delayed_work() instead, which doesn't make such an assumption.
linux-2.6.30-rc1 has the to_delayed_work() function that will allow this
patch to work
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the edac local pci_write_bits32 to properly note the 'escape' mask if
all ones in a 32-bit word.
Currently no consumer of this function uses that mask, so there is no
danger to existing code.
Signed-off-by: Jeff Haran <jharan@Brocade.COM>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce xpc_arch_ops and eliminate numerous individual global definitions.
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Dean Nelson <dcn@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sgi-xpc has a window of failure where an open message can be sent and a
subsequent data message can get lost. We have added a new message
(opencomplete) which closes that window.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The heartbeat timeout functionality in sgi-xpc is currently not trained to
the connection time. If a connection is made and the code is in the last
polling window prior to doing a timeout, the next polling window will see
the heartbeat as unchanged and initiate a no-heartbeat disconnect.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the second go through of the old DMA_nBIT_MASK macro,and there're not
so many of them left,so I put them into one patch.I hope this is the last round.
After this the definition of the old DMA_nBIT_MASK macro could be removed.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Greg KH <greg@kroah.com>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Support the Intel 854 Chipset in fbdev.
We test and use the patch on a Thomson IP1101 IPTV-Box. On the VGA-Port
we get a normal signal.
Here is the link to the Mambux-Project: http://www.mambux.de
Cc: Keith Packard <keithp@keithp.com>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Stefan Husemann <shusemann@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The "simplify spi_write_then_read()" patch included two regressions from
the 2.6.27 behaviors:
- The data it wrote out during the (full duplex) read side
of the transfer was not zeroed.
- It fails completely on half duplex hardware, such as
Microwire and most "3-wire" SPI variants.
So, revert that patch. A revised version should be submitted at some
point, which can get the speedup on standard hardware (full duplex)
without breaking on less-capable half-duplex stuff.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: <stable@kernel.org> [2.6.28.x, 2.6.29.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Do not allow modes with unsupported pixel depth. Otherwise, one can hang
a computer by setting incorrect value with fbset command.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sisfb incorrectly sets the length of the color fields to 6 bits
for PSEUDOCOLOR modes, even though 8 bits are always used per pixel.
Fix this by setting the length to 8.
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sa1100fb incorrectly sets the length of the color fields to 8 bits for
PSEUDOCOLOR modes for which only 4 bits are used per pixel. Fix this by
setting the length to 4 bits for these modes.
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
s3fb incorrectly sets the length of the color fields to 6 bits for
PSEUDOCOLOR modes, even though 8 or 4 bits are used per pixel. Fix this
by setting the length to 8 or 4, respectively.
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Acked-by: Ondrej Zajicek <santiago@crfreenet.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Data sheet at:
http://www.sensirion.ch/en/pdf/product_information/Datasheet-humidity-sensor-SHT1x.pdf
These sensors communicate over a 2 wire bus running a device specific
protocol. The complexity of the driver is mainly due to handling the
substantial delays between requesting a reading and the device pulling the
data line low to indicate that the data is available. This is handled by
an interrupt that is disabled under all other conditions.
I wasn't terribly clear on the best way to handle this, so comments on
that aspect would be particularly welcome!
Interpretation of the temperature depends on knowing the supply voltage.
If configured in a board config as a regulator consumer this is obtained
from the regulator subsystem. If not it should be provided in the
platform data.
I've placed this driver in the hwmon subsystem as it is definitely a
device that may be used for hardware monitoring and with it's relatively
slow response times (up to 120 millisecs to get a reading) a caching
strategy certainly seems to make sense!
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
efifb will attempt to ioremap a framebuffer even if its starting address
is 0, failing and causing an ugly backtrace in the process. Exit before
probing if this is the case.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Peter Jones <pjones@redhat.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
uvesafb incorrectly sets the length of the color fields to 6 bits for
PSEUDOCOLOR modes, even though 8 bits are always used per pixel. Fix this
by setting the length to 8.
The switch of the DAC width from the default 6 bits to 8 bits is retained
and tracked internally in the driver, but never exposed to userspace.
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Acked-by: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: <syrjala@sci.fi>
Cc: Geert Uytterhoeven <geert.uytterhoeven@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The documentation about the meaning of the color component bitfield
lengths in pseudocolor modes is inconsistent. Fix it, so that it
indicates the correct interpretation everywhere, i.e. that 1 << length is
the number of palette entries.
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Acked-by: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: <syrjala@sci.fi>
Acked-by: Geert Uytterhoeven <geert.uytterhoeven@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fb_notifier_call_chain() is called with info->lock held, i.e. in
do_fb_ioctl() => FBIOPUT_VSCREENINFO => fb_set_var() and the some
notifier callbacks, like fbcon_event_notify(), try to re-acquire
info->lock again.
Remove the lock/unlock_fb_info() in all the framebuffer notifier
callbacks' and be sure to always call fb_notifier_call_chain() with
info->lock held.
Reported-by: Pavel Roskin <proski@gnu.org>
Reported-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Andrea Righi <righi.andrea@gmail.com>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add did_interrupt() function to check if a PHY port
really caused an interrupt. This is needed in the case
of shared PHY interrupt pin configuration to stop
interrupt event processing for PHY ports which didn't
cause an interrupt.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell 88E1121R Dual PHY device can be hardware-configured
to use shared interrupt pin for both PHY ports. For such
PHY configurations using shared PHY interrupt phy_interrupt()
handler will also schedule a work for PHY port which didn't
cause an interrupt.
This patch adds a possibility for PHY drivers to provide
did_interrupt() function which reports if the PHY (or a PHY
port in a multi-PHY device) generated an interrupt. This
function is called in phy_change() as phy_change() shouldn't
proceed if it is invoked for a PHY which didn't cause an
interrupt. So check for interrupt originator in phy_change()
to allow early-out.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the Marvell M88E1121R Dual GigE PHY
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We noticed on parisc that our broadcoms all swapped MAC addresses going
from 2.6.29 to 2.6.30-rc1:
Apr 11 07:48:24 ion kernel: eth0: Tigon3 [partno(BCM95700A6) rev 0105] (PCI:66MHz:64-bit) MAC address 00:30:6e:4b:15:59
Apr 13 07:34:34 ion kernel: eth0: Tigon3 [partno(BCM95700A6) rev 0105] (PCI:66MHz:64-bit) MAC address 00:00:59:15:4b:6e
The problem patch is:
commit 6d348f2c1e
Author: Matt Carlson <mcarlson@broadcom.com>
Date: Wed Feb 25 14:25:52 2009 +0000
tg3: Eliminate tg3_nvram_read_swab()
With the root cause being the use of memcpy to set the mac address:
memcpy(&dev->dev_addr[0], ((char *)&hi) + 2, 2);
memcpy(&dev->dev_addr[2], (char *)&lo, sizeof(lo));
This might work on little endian machines, but it can't on big endian
ones. You have to use the original setting mechanism to be correct on
all architectures.
The attached patch fixes parisc.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race between resume from hibernation and the asynchronous
scanning of SCSI devices and to prevent it from happening we need to
call scsi_complete_async_scans() during resume from hibernation.
In addition, if the resume from hibernation is userland-driven, it's
better to wait for all device probes in the kernel to complete before
attempting to open the resume device.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c: Let new-style drivers implement attach_adapter
i2c: Fix sparse warnings for I2C_BOARD_INFO()
i2c-voodoo3: Deprecate in favor of tdfxfb
i2c-algo-pca: Fix use of uninitialized variable in debug message
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] omap_wdt.c: move probe function to .devinit.text
[WATCHDOG] ks8695_wdt.c: move probe function to .devinit.text
[WATCHDOG] at91rm9200_wdt.c: move probe function to .devinit.text
[WATCHDOG] remove ARM26 sections
[WATCHDOG] orion5x_wdt: Add shutdown callback, use watchdog ping function
[WATCHDOG] i6300esb.c: Restructure initialization of the device
[WATCHDOG] i6300esb.c: Fix the GETSTATUS and GETBOOTSTATUS ioctls.
[WATCHDOG] i6300esb.c: Cleanup
While it isn't the way the standard device binding model works, it is
OK for new-style drivers to implement attach_adapter. It may help
convert the renaming legacy drivers to new style drivers faster.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Support for I2C/DDC was recently added to the tdfxfb driver, which
means that the i2c-voodoo3 driver can be deprecated.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
A recent change broke debugging of pca_xfer(), fix it.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Also remove the now-useless debug printouts which are supposed to
tell us when the scan starts and ends.
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Along with MCP65, MCP67 and 73 also don't set CAP_NCQ. Force it.
Reported by zaceni@yandex.ru on bko#13014 and confirmed by Peer Chen.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: NightFox <zaceni2@yandex.ru>
Cc: Peer Chen <pchen@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix a zero address hole bug in the bonding arp_ip_target list
that was causing the bond to ignore ARP replies (bugz 13006).
Instead of just setting the array entry to zero, we now
copy any additional entries down one slot, putting the
zero entry at the end. With this change we can now have
all the loops that walk the array stop when they hit a zero
since there will be no addresses after it.
Changes are based in part on code fragment provided in kernel:
bugzilla 13006:
http://bugzilla.kernel.org/show_bug.cgi?id=13006
by Steve Howard <steve@astutenetworks.com>
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The input core will add entropy to the pool so this flag is not
needed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Noises can be introduced when LCD signals are being driven, some platforms
provide a signal to assist the synchronization of this sampling procedure.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There is no need to issue serialize_rcu() after adding a new handle
to the list of handles associated with the device because new events
will "see" the new handle in the list immediately. Remove it so we
can boot a little bit faster.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There are several DMI tables in the i8042 (keyboard) driver already, but
not one for the i8042.reset option. This patch adds such an option.
Two users for this table are added as well, the MSI Wind U-100 and the LG
X110. The MSI Wind also needs to be in the "don't trust the pnp data" for
the touchpad to work on my machine.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Some touchpads don't reset right the first time (MSI Wind U-100 for
example). This patch will retry the reset up to 5 times.
In addition, on x86, we don't fail entire i8042 initialization if
controller reset fails in hope that keyboard port will still be
functional and user will still get a working keyboard. This is
especially important on netbooks.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This reverts commit 5d38258ec0, since the
underlying problem got fixed properly in the previous commit ("async:
Fix module loading async-work regression").
Cc: Arkadiusz Miskiewicz <a.miskiewicz@gmail.com>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Len Brown <len.brown@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The driver is currently dumping a message in the log about failing to
allocate vf data when max_vfs is equal to 0. This change makes it so the
error message is only displayed if we set max_vfs to a non zero value.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The igbvbf driver exposed several unused extrnal references due to the fact
that code was copied from igb and then some functionality was removed.
This changes that so that unused functions are either removed or made
static.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were several unused external references added with the sr-iov
enablement changes. This patch changes all those references to static
local references.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: Subrata Modak <subrata@linux.vnet.ibm.com>
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: Subrata Modak <subrata@linux.vnet.ibm.com>
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix this warning:
drivers/net/via-velocity.c:1924: warning: passing argument 2 of 'request_irq' from incompatible pointer type
Signed-off-by: Seguier Regis <rseguier@e-teleport.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
platform_device_register_simple() returns ERR_PTR() and not NULL.
Found by smatch (http://repo.or.cz/w/smatch.git). Compile tested.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All NICs were reporting WOL support when only the KX4 NIC is capable of
supporting WOL. This patch adds a function to check for and exclude all
non-WOL capable nics from enabling WOL in ethtool.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LED blink code is common for 82599 as well. It should be moved to
ixgbe_common.c so both devices can use it, and not have it duplicated.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the BIOS does something obviously stupid, like claiming that the
registers for the IOMMU are at physical address zero, then print a nasty
message and abort, rather than trying to set up the IOMMU and then later
panicking.
It's becoming more and more obvious that trusting this stuff to the BIOS
was a mistake.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In the current code, for a box with an indexed _BQC method, we
1. get the current brightness level by evaluating _BQC
2. set the value gotten in step 1 to _BCM
3. get the current brightness level again
4. set the _BQC_use_index flag if the results gotten
in step 1 and in step 3 don't equal.
But this logic doesn't work actually, because the _BQC_use_index
is not set when acpi_video_device_lcd_set_level is invoked.
This results in a failure in step 2.
http://bugzilla.kernel.org/show_bug.cgi?id=12249#c83
Now, we set the _BQC_use_index flag after invoking _BQC for the first
time. And reevaluate the _BQC to get the correct brightness level.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch removes the driver distinction between control method (CM)
and fixed hardware (FF) buttons. We previously needed that so we
could install either a fixed event handler or a notify handler, but
the Linux/ACPI code now handles that for us, so we don't need to
worry about it.
Note that this removes the FF/CM annotation from the "info" files
in /proc. For example,
/proc/acpi/button/PWRF/info:
-type: Power Button (FF)
+type: Power Button
I don't think there's anything meaningful user-space can do by
knowing whether a button is a control method or a fixed hardware
button, so nobody should be looking at the FF/CM.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We no longer need a pointer from struct acpi_button back to the
struct acpi_device. Everywhere we used that pointer, we either
already have, or can easily get, the acpi_device pointer without
using the copy from acpi_button. So this patch removes the
structure element.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch adds temporaries to cache the acpi_device_hid(),
acpi_device_name(), and acpi_device_class() pointers so we
don't have to clutter the code with so many uses of those
interfaces.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
It's typical and slightly more compact to look up the driver_data
structure by initializing the automatic variable at its definition.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Better to oops and learn about a bug than to silently cover it up.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch changes a bit of whitespace to follow Linux conventions.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-2.6-mn10300:
Separate out the proc- and unit-specific header directories from the general
Move arch headers from include/asm-mn10300/ to arch/mn10300/include/asm/.
MN10300 arch headers and place them instead in the same directories as contain
the .c files for the processor and unit implementations.
This permits the symlinks include/asm/proc and include/asm/unit to be
dispensed with. This does, however, require that #include <asm/proc/xxx.h> be
converted to #include <proc/xxx.h> and similarly for asm/unit -> unit.
Signed-off-by: David Howells <dhowells@redhat.com>
/dev/mem mmap code was doing memtype reserve/free for a while now.
Recently we added memtype tracking in remap_pfn_range, and /dev/mem mmap
uses it indirectly. So, we don't need seperate tracking in /dev/mem code
any more. That means another ~100 lines of code removed :-).
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
LKML-Reference: <20090409212709.085210000@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (27 commits)
xsysace: Fix dereferencing of cf_id after hd_driveid removal
at91_ide: turn on PIO 6 support
at91_ide: remove unused ide_mm_{outb,inb}
ide-cd: reverse NOT_READY sense key logic
ide: refactor tf_read() method
ide: refactor tf_load() method
ide: call write_devctl() method from tf_read() method
ide: move common code out of tf_load() method
ide: simplify 'struct ide_taskfile'
ide: replace IDE_TFLAG_* flags by IDE_VALID_*
ide-cd: fix intendation in cdrom_decode_status()
ide-cd: unify handling of fs and pc requests in cdrom_decode_status()
ide-cd: convert cdrom_decode_status() to use switch statements
ide-cd: update debugging support
ide-cd: respect REQ_QUIET for fs requests in cdrom_decode_status()
ide: remove unused #include <linux/version.h>
tx4939ide: Fix tx4939ide_{in,out}put_data_swap argument
tx493[89]ide: Remove big endian version of tx493[89]ide_tf_{load,read}
ide-cd: carve out an ide_cd_breathe()-helper for fs write requests
ide-cd: move status checking into the IRQ handler
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/nes: Add support for new SFP+ PHY
RDMA/nes: Add wide_ppm_offset parm for switch compatibility
RDMA/nes: Fix SFP+ PHY initialization
RDMA/nes: Fix nes_nic_cm_xmit() error handling
RDMA/nes: Fix error handling issues
RDMA/nes: Fix incorrect casts on 32-bit architectures
IPoIB: Document newish features
RDMA/cma: Create cm id even when IB port is down
RDMA/cma: Use rate from IPoIB broadcast when joining IPoIB multicast groups
IPoIB: Avoid free_netdev() BUG when destroying a child interface
mlx4_core: Don't leak mailbox for SET_PORT on Ethernet ports
RDMA/cxgb3: Release dependent resources only when endpoint memory is freed.
RDMA/cxgb3: Handle EEH events
IB/mlx4: Use pgprot_writecombine() for BlueFlame pages
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
igb: remove sysfs entry that was used to set the number of vfs
igbvf: add new driver to support 82576 virtual functions
drivers/net/eql.c: Fix a dev leakage.
niu: Fix unused variable warning.
r6040: set MODULE_VERSION
bnx2: Don't use reserved names
FEC driver: add missing #endif
niu: Fix error handling
mv643xx_eth: don't reset the rx coal timer on interface up
smsc911x: correct debugging message on mii read timeout
ethoc: fix library build errors
netfilter: ctnetlink: fix regression in expectation handling
netfilter: fix selection of "LED" target in netfilter
netfilter: ip6tables regression fix
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc: Hook up sys_preadv and sys_pwritev
sparc64: add_node_ranges() must be __init
serial: sunsu: sunsu_kbd_ms_init needs to be __devinit
sparc: Fix section mismatch warnings in cs4231 sound driver.
sparc64: Fix section mismatch warnings in PCI controller drivers.
sparc64: Fix section mismatch warnings in power driver.
sparc64: get_cells() can't be marked __init
If the thread calling dm_kcopyd_copy is delayed due to scheduling inside
split_job/segment_complete and the subjobs complete before the loop in
split_job completes, the kcopyd callback could be invoked from the
thread that called dm_kcopyd_copy instead of the kcopyd workqueue.
dm_kcopyd_copy -> split_job -> segment_complete -> job->fn()
Snapshots depend on the fact that callbacks are called from the singlethreaded
kcopyd workqueue and expect that there is no racing between individual
callbacks. The racing between callbacks can lead to corruption of exception
store and it can also mean that exception store callbacks are called twice
for the same exception - a likely reason for crashes reported inside
pending_complete() / remove_exception().
This patch fixes two problems:
1. job->fn being called from the thread that submitted the job (see above).
- Fix: hand over the completion callback to the kcopyd thread.
2. job->fn(read_err, write_err, job->context); in segment_complete
reports the error of the last subjob, not the union of all errors.
- Fix: pass job->write_err to the callback to report all error bits
(it is done already in run_complete_job)
Cc: stable@kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Use a variable in segment_complete() to point to the dm_kcopyd_client
struct and only release job->pages in run_complete_job() if any are
defined. These changes are needed by the next patch.
Cc: stable@kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Barriers are submitted to a worker thread that issues them in-order.
The thread is modified so that when it sees a barrier request it waits
for all pending IO before the request then submits the barrier and
waits for it. (We must wait, otherwise it could be intermixed with
following requests.)
Errors from the barrier request are recorded in a per-device barrier_error
variable. There may be only one barrier request in progress at once.
For now, the barrier request is converted to a non-barrier request when
sending it to the underlying device.
This patch guarantees correct barrier behavior if the underlying device
doesn't perform write-back caching. The same requirement existed before
barriers were supported in dm.
Bottom layer barrier support (sending barriers by target drivers) and
handling devices with write-back caches will be done in further patches.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Remove queue_io return value and a loop in dm_request.
IO may be submitted to a worker thread with queue_io(). queue_io() sets
DMF_QUEUE_IO_TO_THREAD so that all further IO is queued for the thread. When
the thread finishes its work, it clears DMF_QUEUE_IO_TO_THREAD and from this
point on, requests are submitted from dm_request again. This will be used
for processing barriers.
Remove the loop in dm_request. queue_io() can submit I/Os to the worker thread
even if DMF_QUEUE_IO_TO_THREAD was not set.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Rework shutting down on suspend and document the associated rules.
Drop write lock in __split_and_process_bio to allow more processing
concurrency.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Refactor the code in dm_request().
Require the new DMF_BLOCK_FOR_SUSPEND flag on readahead bios we will
discard so we don't drop such bios while processing a barrier.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Split the DMF_BLOCK_IO flag into two.
DMF_BLOCK_IO_FOR_SUSPEND is set when I/O must be blocked while suspending a
device. DMF_QUEUE_IO_TO_THREAD is set when I/O must be queued to a
worker thread for later processing.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Prepare for full barrier implementation: first remove the restricted support.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch provides support for data integrity passthrough in the device
mapper.
- If one or more component devices support integrity an integrity
profile is preallocated for the DM device.
- If all component devices have compatible profiles the DM device is
flagged as capable.
- Handle integrity metadata when splitting and cloning bios.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch removes the sysfs entry num_vfs which was added to support
enabling pci virtual functions for 82576.
To prevent VFs from loading automatically a module parameter "max_vfs" was
added so that the number of VFs per PF can be limited. This is especially
useful when 4 or more 82576 ports are on the system because otherwise to
load all VFs would result in 8 interface per physical port.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds an igbvf driver to handle virtual functions provided by the
igb driver when SR-IOV has been enabled. A virtual function is a
lightweight pci-e function that supports a single queue and shares
resources with the 82576 physical function contained within the igb
driver.
To spawn virtual functions from the igb driver all that is needed is to
enable CONFIG_PCI_IOV and have an 82576 Ethernet adapter on a system that
supports SR-IOV in the BIOS. The virtual functions will appear after the
interface is loaded.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After dev_get_by_name(), we should follow a dev_put().
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch sets MODULE_VERSION in order to help users track
changes to this module.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mips identifier is reserved by gcc on mips plattforms. Don't use it
in the code.
Signed-off-by: Bastian Blank <waldi@debian.org>
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
platform_device_register_simple() returns ERR_PTR(), not NULL, if an error
occurs.
Found by smatch (http://repo.or.cz/w/smatch.git). Compile tested.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move SDMA configuration from interface up to port probe, to prevent
overwriting the receive coalescing timer value on interface up.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the warning printed when a mii READ times out currently says "Timed out
waiting for MII write to finish". This patch corrects this.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethoc indirectly uses crc32_le() and bitrev32(), so select
those library functions to be built.
drivers/built-in.o: In function `ethoc_set_multicast_list':
ethoc.c:(.text+0x6226f): undefined reference to `crc32_le'
ethoc.c:(.text+0x62276): undefined reference to `bitrev32'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
x86 ACPI: Add support for Always Running APIC timer
ACPI x86: Make aperf/mperf MSR access in acpi_cpufreq read_only
ACPI x86: Cleanup acpi_cpufreq structures related to aperf/mperf
ACPICA: delete check for AML access to port 0x81-83
ACPI: WMI: use .notify method instead of installing handler directly
sony-laptop: use .notify method instead of installing handler directly
panasonic-laptop: use .notify method instead of installing handler directly
fujitsu-laptop: use .notify method instead of installing hotkey handler directly
fujitsu-laptop: use .notify method instead of installing handler directly
ACPI: video: use .notify method instead of installing handler directly
ACPI: thermal: use .notify method instead of installing handler directly
ACPI battery: fix async boot oops
ACPI: delete acpi_device.g_list
NULL noise: drivers/platform/x86/panasonic-laptop.c
ACPI: cpufreq: remove dupilcated #include
ACPI: Adjust Kelvin offset to match local implementation
ACPI: convert acpi_device_lock spinlock to mutex
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 5446/1: ohci-at91: Limit vbus_pin assignment to the size of the array
[ARM] 5445/1: AT91: Remove flexible array from USBH platform data
[ARM] 5447/1: Add SZ_32K
[ARM] omap: fix omap1 clock usecount decrement bug
[ARM] pxa: register AC97 controller devices
[ARM] pxa/csb701: do not register devices on non-csb726 boads
[ARM] pxa/colibri: get rid of set_irq_type()
[ARM] pxa/colibri: provide MAC address from ATAG_SERIAL
[ARM] pxa/cm-x2xx: fix ucb1400 not being registered
[ARM] pxa: Add support for suspend on PalmTX, T5 and LD
[ARM] pxa: PalmTE2 support for battery, UDC, IrDA and backlight
[ARM] pxa: Palm Tungsten E2 basic support
[ARM] pxa/em-x270: add libertas device registration
[ARM] pxa/magician: Enable bq24022 regulator for gpio_vbus and pda_power
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
mmc_spi: support for non-byte-aligned cards
omap_hsmmc: Do not expect cmd/data to be non-null when CC/TC occurs
mmc: Fix compile for omap_hsmmc.c
mmc_spi: convert timeout handling to jiffies and avoid busy waiting
mmc_spi: do not check CID and CSD blocks with CRC16
omap_hsmmc: Flush posted write to IRQ
New mail address for Pierre Ossman
imxmmc: move RSSR BLR
imxmmc: init-exit rework
mmc: Accept EXT_CSD rev 1.3 since it is backwards compatible with 1.2
Thou shalt remember to use 'git add' or errors shall be visited on your
downloads and there shall be wrath from on list and much gnashing of teeth.
Thou shalt remember to use git status or there shall be catcalls and much
embarrasment shall come to pass.
Signed-off-by: Alan "I'm hiding" Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add new register settings for new SFP+ PHY/firmware.
Add new PHY to to nes_netdev_get/set_settings.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We have observed unstable link with a new BNT switch.
Add wide_ppm_offset parameter to allow the user to control the clock
ppm offset on the CX4 interface for better compatibility. Default is
100ppm, setting it to 1 will increase it to 300ppm. Change default
SerDes1 reference clock to external source.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
SFP+ PHY initialization has very long delays, incorrect settings for
direct attach copper cables, and inconsistent link detection.
Adjust delays to the minimum required by the PHY. Worst case is now
less than 4 seconds. Add new register settings for direct attach
cables. Change link detection logic to use two new registers for more
consistent link state detection. Reorganize code to shorten line
length.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If a VM is booted with offline VCPUs then unplug them during boot. Determining
the availability of a VCPU requires access to XenStore which is not available
at the point smp_prepare_cpus() is called, therefore we bring up all VCPUS
initially and unplug the offline ones as soon as XenStore becomes available.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Impact: bugfix Xen domain restore
Otherwise the first timer interrupt after resume is missed and we never
get another.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
We are getting crash or hung situation when we are running network
cable pull tests during RDMA traffic.
In schedule_nes_timer(), we return an error if nes_nic_cm_xmit()
returns failure. This is changed to success as skb is being put on
the timer routines to be processed later. In send_syn() case, we are
indicating connect failure once from nes_connect() and the other when
the rexmit retries expires.
The other issue is skb->users which we are incrementing before calling
nes_nic_cm_xmit() which calls dev_queue_xmit() but in case of failure
we are decrementing the skb->users at the same time putting the skb on
the rexmit path. Even if dev_queue_xmit() fails, the skb->users is
decremented already. We are removing the decrement of skb->users in
case of failure from both schedule_nes_timer() as well as from
nes_cm_timer_tick().
There is also extra check in nes_cm_timer_tick() for rexmit failure
which does a break from the loop is removed. This causes problem as
the other nodes have their cm_node->ref_count incremented and are not
processed.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix issues found by static code analysis:
(1) Check if cm_node was successfully created for loopback connection.
(2) schedule_nes_timer() does not free up allocated memory after
encountering an error. There is a WARN_ON() for this condition.
(3) there is a cm_node->freed flag which is set but not used.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The were some incorrect casts to unsigned long that caused 64-bit values
to be truncated on 32-bit architectures and made the driver pass invalid
adresses and lengths to the hardware. The problems were primarily seen
with kernels with highmem configured but some could show up in
non-highmem kernels, too.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When doing rdma_resolve_addr(), if the relevant IB port is down, the
function fails and the cm_id is not bound to the correct device.
Therefore, application does not have a device handle and cannot wait
for the port to become active. The function fails because the
underlying IPoIB interface is not joined to the broadcast group and
therefore the SA does not have a multicast record to take a Q_Key
from.
The fix is to use lazy Q_Key resolution - cma_set_qkey() will set
id_priv->qkey if it was not set, and will be called just before the
Q_Key is really required.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Currently, the vbus_pin assignment loop is limited by the value of the "ports"
variable in the platform data. Now that the vbus_pin array is no longer
flexible, we can use its actual size.
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A very large subset of SD cards in the market send their
responses and data non-byte-aligned. So add logic to the
mmc spi driver to handle this mess.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
With spurious interrupt cmd can be null even when we have CC
set in irq status.
Fixes: NB#106295 - prevent potential kernel crash in the MMC driver
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
This fixes the issue noted by Russell King:
drivers/mmc/host/omap_hsmmc.c: In function 'mmc_omap_xfer_done':
drivers/mmc/host/omap_hsmmc.c:301: error: implicit declaration of function 'mmc_omap_fclk_lazy_disable'
This got broken by 4a694dc915.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
SD/MMC card timeouts can be very high. So avoid busy-waiting,
using the scheduler. Calculate all timeouts in jiffies units,
because this will give us the correct sign when to involve
the scheduler.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Some cards are not able to calculate a valid CRC16 value
for CID and CSD reads (CRC for 512 byte data blocks is OK).
By moving the CRC enable after the read of CID and CSD, these
cards can be used. This patch was tested with a faulty 8 GByte
takeMS Class 6 SDHC card. This patch was suggested by
Pierre Ossman.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Spurious IRQs seen on MMC after 2.6.29. Flush posted write in IRQ
handler.
The interrupt line is released by clearing the error status bits
in the MMCHS_STAT register, which must occur before the interrupt
handler returns to avoid unwanted irqs. Hence the need to flush
the posted write.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Tony Lindgen <tony@atomide.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
DMA request source (RSSR) needs to be set only once (in probe).
DMA burst length (BLR) need to be set only in set_ios()
This cleans up imxmci_setup_data() and should make it a little
bit faster :)
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Add __init __exit for appropriate probe and remove functions.
Conver to platform_driver_probe()
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Save the bit 17 state of the pages when freeing the page list, and
reswizzle them if necessary when rebinding the pages (in case they were
swapped out). Since we have userland with expectations that the swizzle
enums let it pread and pwrite contents accurately, we can't expose a new
swizzle enum for bit 17 (which it would have to GTT map to handle), so we
handle it down in pread and pwrite by swizzling the copy when bit 17 of the
page address is set.
Signed-off-by: Eric Anholt <eric@anholt.net>
Otherwise, the results of our read didn't show up when we were faulting in
the page being read into (as happened with a testcase reading into a big
stack area). Likely accounts for some conformance test failures.
Signed-off-by: Eric Anholt <eric@anholt.net>
i915_gem_put_relocs_to_user returned an uninitialized value which
got returned to userspace. This caused libdrm in my setup to never
get out of a do{}while() loop retrying i915_gem_execbuffer.
result was hanging X, overheating of cpu and 2-3gb of logfile-spam.
This patch adresses the issue by
1. initializing vars in this file where necessary
2. correcting wrongly interpreted return values of copy_[from/to]_user
Signed-off-by: Florian Mickler <florian@mickler.org>
[anholt: cleanups of unnecessary changes, consistency in APIs]
Signed-off-by: Eric Anholt <eric@anholt.net>
At the same time, bring the action message closer to the usual format.
Signed-off-by: Ferenc Wagner <wferi@niif.hu>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Currently we detect HDMI monitor by hardware detection, but if an HDMI-DVI
adapter is used to connect a DVI monitor, hardware detection will incorrectly
take monitor as HDMI. HDMI spec says any device containing IEEE registration
identifier will be treated as HDMI device. The patch intends to detect HDMI
monitor by drm_detect_hdmi_monitor function which follows that rule.
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
We create a debugfs node (i915_ringbuffer_data) to expose a hex dump
of the ring buffer itself. We also expose another debugfs node
(i915_ringbuffer_info) with information on the state (i.e. head, tail
addresses) of the ringbuffer.
For batchbuffer dumping, we look at the device's active_list, dumping
each object which has I915_GEM_DOMAIN_COMMAND in its read
domains. This is all exposed through the dri/i915_batchbuffers debugfs
file with a header for each object (giving the objects gtt_offset so
that it can be matched against the offset given in the
BATCH_BUFFER_START command.
Signed-off-by: Ben Gamari <bgamari@gmail.com>
Signed-off-by: Carl Worth <cworth@cworth.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Fix build problems with leds-gpio:
CC drivers/leds/leds-gpio.o
drivers/leds/leds-gpio.c: In function 'create_gpio_led':
drivers/leds/leds-gpio.c:85: warning: 'return' with no value, in function returning non-void
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Commit 4aaf2fec71 (xsysace: make it
'struct hd_driveid'-free) converted the cf_id member of 'struct
ace_device' from a 'struct hd_driveid' to a u16 array. However,
references to the base of the structure were still using the '&'
operator. When the address was used with the ata_id_u32() macro, the
compiler used the size of the entire array instead of sizeof(u16) to
calculate the offset from the base address.
This patch removes the use of the '&' operator from all references of
cf_id to fix the bug and remove future confusion.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
As we have already PIO 6 transfer mode supported in IDE layer, we can turn
it on in the driver.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: "Steve Wootton" <swootton@esi-estech.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make the case of flushing the drive's cache explicit.
There should be no functional change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Simplify tf_read() method, making it deal only with 'struct ide_taskfile' and
the validity flags that the upper layer passes, and factoring out the code that
deals with the high order bytes into ide_tf_readback() to be called from the
only two functions interested, ide_complete_cmd() and ide_dump_sector().
This should stop the needless code duplication in this method and so make
it about twice smaller than it was; along with simplifying the setup for
the method call, this should save both time and space...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Simplify tf_load() method, making it deal only with 'struct ide_taskfile' and
the validity flags that the upper layer passes, and moving the code that deals
with the high order bytes into the only function interested, do_rw_taskfile().
This should stop the needless code duplication in this method and so make
it about twice smaller than it was; along with simplifying the setup for the
method call, this should save both time and space...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use write_devctl() method to clear/set the HOB bit in tf_read() method.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move device register masking (and setting drive->select) out of tf_load() method
and into the only function that needs to use this code, do_rw_taskfile()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
[bart: fix whitespace error]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make 'struct ide_taskfile' cover only 8 register values and thus put two such
fields ('tf' and 'hob') into 'struct ide_cmd', dropping unnecessary 'tf_array'
field from it.
This required changing the prototype of ide_get_lba_addr() and ide_tf_dump().
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
[bart: fix setting of ATA_LBA bit for LBA48 commands in __ide_do_rw_disk()]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Replace IDE_TFLAG_{IN|OUT}_* flags meaning to the taskfile register validity on
input/output by the IDE_VALID_* flags and introduce 4 symmetric 8-bit register
validity indicator subfields, 'valid.{input/output}.{tf|hob}', into the 'struct
ide_cmd' instead of using the 'tf_flags' field for that purpose (this field can
then be turned from 32-bit into 8-bit one).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Based on earlier work by Borislav Petkov.
Fix intendation in cdrom_decode_status(), no real code changes.
While at it:
- beautify comments
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Based on earlier work by Borislav Petkov.
Unify handling of fs and pc requests in cdrom_decode_status().
While at it:
- remove unreachable code
The only change in functionality is that for pc requests more
detailed error message will be printed for following sense keys:
* ILLEGAL_REQUEST
* DATA_PROTECT
* MEDIUM_ERROR
* BLANK_CHECK
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Based on earlier work by Borislav Petkov.
Convert cdrom_decode_status() to use switch statements in
preparation to unify handling of fs and pc requests.
While at it:
- remove superfluous comments and do minor CodingStyle fixups
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional change resulting from this patch.
Suggested-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Now tx493[89]ide_tf_{load,read} do not contain word I/O operations.
They are endian-free now.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>,
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since tf_{read|load}() methods of this driver have now become identical to their
standard counterparts using I/O port accesses, there's no need to override those
anymore...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since tf_{read|load}() methods of this driver have now become identical to their
standard counterparts using MMIO accesses, there's no need to override those
anymore...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove two no longer used functions that I've overlooked...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* define CHECK_DMA_MASK
* remove use of wmb()
Reported-by: Grant Grundler <grundler@google.com>
Reviewed-by: Grant Grundler <grundler@google.com>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
This patch:
o replaces "mask" variable in ide_dma_end() with #define.
o removes use of wmb() in ide-dma-sff.c and scc_pata.c.
o is not tested - I don't have (or want) the HW.
Signed-off-by: Grant Grundler <grundler@google.com>
Cc: KOBAYASHI Yoshitake <yoshitake.kobayashi@toshiba.co.jp>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Both of commits f94116aeec ("ide: cleanup
<asm-m68k/ide.h>") and 15a453a955 ("ide: include
<asm/ide.h> only when needed") break falconide:
| Uniform Multi-Platform E-IDE driver
| ide: Falcon IDE controller
| Probing IDE interface ide0...
| hda: Sarge m68k, ATA DISK drive
| ide0 at 0xfff00000 on irq 15 (serialized)
| ide-gd driver 1.18
| hda: max request size: 128KiB
| hda: 2118816 sectors (1084 MB) w/256KiB Cache, CHS=2102/16/63
| hda:<4>hda: lost interrupt
This happens because falconide relies on {in,out}sw() being redefined in
<asm/ide.h>, as included by <linux/ide.h>, which is no longer the case.
Use __ide_mm_{in,out}sw() from <asm/ide.h> instead, just like
ide_{in,out}put_data() do.
The same problem seems to exist in q40ide.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
commit 255115fb35 ("ide: allow host drivers to
specify IRQ flags") added irq_flags fields to struct ide_port_info and struct
ide_host. Drivers can now set ide_port_info.irq_flags = IRQF_SHARED, while
init_irq() passes ide_host.irq_flags to request_irq().
Unfortunately ide_host.irq_flags is never set, causing (on ARAnyM):
| Uniform Multi-Platform E-IDE driver
| ide: Falcon IDE controller
| Probing IDE interface ide0...
| hda: Sarge m68k, ATA DISK drive
| init_irq: sa = 0
| ide0: disabled, unable to get IRQ 15
| ide0: failed to initialize IDE interface
| ide0: disabling port
Solve this by copying ide_port_info.irq_flags to ide_host.irq_flags in
ide_host_alloc().
This bug probably affects the following IDE host drivers:
- buddha
- delkin_cb
- falconide
- gayle
- ide-cs
- macide
- q40ide
- scc_pata
- sgiioc4
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
We were calculating the wrong address for the start of the data.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Tested-by: Jeremy Higdon <jeremy@sgi.com>
A pointer to omap_wdt_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alan Cox <alan@redhat.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: George G. Davis <gdavis@mvista.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
A pointer to ks8695wdt_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Alan Cox <alan@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
A pointer to at91wdt_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Ilpo Jarvinen <ilpo.jarvinen@helsinki.fi>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Removes ARM26 sections from Kconfig and Makefile, because
ARM26 is long gone.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
* Added a callback to disable the watchdog on shutdown.
* Use a separate ping function to reduce the number of register accesses
if the watchdog is already enabled and just needs to be reloaded.
* Minor cleanup of function names.
Signed-off-by: Thomas Reitmayr <treitmayr@devbase.at>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The i6300ESB watchdog should be stopped before userspace has access to the
watchdog. So fix this and restructure the initialization sequence into:
* See if we have a i6300 device
* make sure that we have valid module parameters
* Initialize the device
* register the /dev/watchdog device so that userspace has access
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add support for Always Running APIC timer, CPUID_0x6_EAX_Bit2.
This bit means the APIC timer continues to run even when CPU is
in deep C-states.
The advantage is that we can use LAPIC timer on these CPUs
always, and there is no need for "slow to read and program"
external timers (HPET/PIT) and the timer broadcast logic
and related code in C-state entry and exit.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Sony laptops apparently write 4-bytes (rather than 1 byte)
to debug port 0x80, which spews error messages:
Denied AML access to port 0x00000080/4 (DMA1 0x0081-0x0083) [20090320]
http://bugzilla.kernel.org/show_bug.cgi?id=13036
Signed-off-by: Len Brown <len.brown@intel.com>
This patch adds a .notify() method. The presence of .notify() causes
Linux/ACPI to manage event handlers and notify handlers on our behalf,
so we don't have to install and remove them ourselves.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
CC: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch adds a .notify() method. The presence of .notify() causes
Linux/ACPI to manage event handlers and notify handlers on our behalf,
so we don't have to install and remove them ourselves.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
CC: Mattia Dongili <malattia@linux.it>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch adds a .notify() method. The presence of .notify() causes
Linux/ACPI to manage event handlers and notify handlers on our behalf,
so we don't have to install and remove them ourselves.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
CC: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch adds a .notify() method. The presence of .notify() causes
Linux/ACPI to manage event handlers and notify handlers on our behalf,
so we don't have to install and remove them ourselves.
Tested by Tony on Fujitsu-Siemens Lifebook S6420 [FJNB1E6] with
BIOS 1.18 (01/09/2009). Tested by Jonathan on Fujitsu S7020.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Tony Vroon <tony@linx.net>
Tested-By: Tony Vroon <tony@linx.net>
Acked-by: Jonathan Woithe <jwoithe@physics.adelaide.edu.au>
Tested-by: Jonathan Woithe <jwoithe@physics.adelaide.edu.au>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch adds a .notify() method. The presence of .notify() causes
Linux/ACPI to manage event handlers and notify handlers on our behalf,
so we don't have to install and remove them ourselves.
Tested by Tony on Fujitsu-Siemens Lifebook S6420 [FJNB1E6] with
BIOS 1.18 (01/09/2009). Tested by Jonathan on Fujitsu S7020.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Tony Vroon <tony@linx.net>
Tested-By: Tony Vroon <tony@linx.net>
Acked-by: Jonathan Woithe <jwoithe@physics.adelaide.edu.au>
Tested-by: Jonathan Woithe <jwoithe@physics.adelaide.edu.au>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch adds a .notify() method. The presence of .notify() causes
Linux/ACPI to manage event handlers and notify handlers on our behalf,
so we don't have to install and remove them ourselves.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
CC: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch adds a .notify() method. The presence of .notify() causes
Linux/ACPI to manage event handlers and notify handlers on our behalf,
so we don't have to install and remove them ourselves.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
CC: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
> BUG: unable to handle kernel NULL pointer dereference at (null)
What happens is that the battery module's init sections are being freed
before the async callback (which was marked __init) has run. This theory
is supported by the fact that the bad RIP value is a vmalloc address.
The immediate fix is to make this a non-init call.
(A better long-term fix is of course to wait with init-section unloading
until a module's async initcalls have been run, which would allow us to
discard this function which is still only run once, after all. Perhaps a
new async_initcall() function for the async/module API, if this is needed
for other modules in the future?)
Reported-by: Arkadiusz Miskiewicz <a.miskiewicz@gmail.com>
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Tested-by: Alessandro Suardi <alessandro.suardi@gmail.com>
Tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: pci_slot: grab refcount on slot's bus
PCI Hotplug: acpiphp: grab refcount on p2p subordinate bus
PCI: allow PCI core hotplug to remove PCI root bus
PCI: Fix oops in pci_vpd_truncate
PCI: don't corrupt enable_cnt when doing manual resource alignment
PCI: annotate pci_rescan_bus as __ref, not __devinit
PCI-IOV: fix missing kernel-doc
PCI: Setup disabled bridges even if buses are added
PCI: SR-IOV quirk for Intel 82576 NIC
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
loop: mutex already unlocked in loop_clr_fd()
cfq-iosched: don't let idling interfere with plugging
block: remove unused REQ_UNPLUG
cfq-iosched: kill two unused cfqq flags
cfq-iosched: change dispatch logic to deal with single requests at the time
mflash: initial support
cciss: change to discover first memory BAR
cciss: kernel scan thread for MSA2012
cciss: fix residual count for block pc requests
block: fix inconsistency in I/O stat accounting code
block: elevator quiescing helpers
* 'i2c-for-2630-v2' of git://aeryn.fluff.org.uk/bjdooks/linux:
i2c: imx: Make disable_delay a per-device variable
i2c: xtensa s6000 i2c driver
powerpc/85xx: i2c-mpc: use new I2C bindings for the Socates board
i2c: i2c-mpc: make I2C bus speed configurable
i2c: i2c-mpc: use dev based printout function
i2c: i2c-mpc: various coding style fixes
i2c: imx: Add missing request_mem_region in probe()
i2c: i2c-s3c2410: Initialise Samsung I2C controller early
i2c-s3c2410: Simplify bus frequency calculation
i2c-s3c2410: sda_delay should be in ns, not clock ticks
i2c: iMX/MXC support
PCI parallel port devices can IRQ share so we should stop them hogging
the line and making a mess on modern PC systems. We know the sharing
side works as the PCMCIA driver has shared the parallel port IRQ for
some time.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here are some cleanups, mainly removing unused variables and silly
declarations.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Depend on KGDB_SERIAL_CONSOLE being set to N rather than !Y, since it can
be built as a module.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Both software emulated and hardware based CTS and RTS are enabled in
serial driver.
The CTS RTS PIN connection on BF548 UART port is defined as a modem
device not as a host device. In order to test it under Linux, please
nake a cross UART cable to exchange CTS and RTS signal.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Only the CTS bit is affected.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
(akpm: queued pending confirmation of the new major number)
[randy.dunlap@oracle.com: select SERIAL_CORE]
Signed-off-by: Christian Pellegrin <chripell@fsfe.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Avoid using port->tty where possible (makes refcount fixing easier
later).
Remove unused code (the ioctl path is not used if the device has
mget/mset functions)
Remove various un-needed typecasts and long names so it could read it to
do the changes.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the new general RS485 Linux data structure (introduced by Alan with
commit number c26c56c0f4) in the Cris
architecture too (currently, Cris still uses the old private data
structure instead of the new one).
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com>
Tested-by: Hinko Kocevar <hinko.kocevar@cetrtapot.si>
Tested-by: Janez Cufer <janez.cufer@cetrtapot.si>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_24BIT_MASK macro with DMA_BIT_MASK(24)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_28BIT_MASK macro with DMA_BIT_MASK(28)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_30BIT_MASK macro with DMA_BIT_MASK(30)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_31BIT_MASK macro with DMA_BIT_MASK(31)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_39BIT_MASK macro with DMA_BIT_MASK(39)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_40BIT_MASK macro with DMA_BIT_MASK(40)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_48BIT_MASK macro with DMA_BIT_MASK(48)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1. check for errors returned from clk_get()
2. fix "Unbalanced enable for IRQ 160"
3. fix transmit descriptor handling in panning
4. clean frame buffer on blank - useful for OLED displays
5. formatting clean up
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Read DDC information from a connected monitor and use it to select initial
mode (if the mode is not specified).
Also, use the information to protect against modes outside the monitor
specs.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Tested-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The I2C functionality provided by the i2c-voodoo3 driver is moved into the
tdfxfb (frame buffer driver for Voodoo3 cards). This way there is no
conflict between the i2c driver and the fb driver.
The tdfxfb does not make use from the DDC functionality yet but provides
all the functionality of the i2c-voodoo3 driver.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most SPI peripherals use GPIOs as their chip selects, introduce .gpio_cs
for this.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With a postfix decrement limit will reach -1 rather than 0, so the warning
will not be issued.
Also, add a cpu_relax() into the busy-wait loop.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Mariusz Ceier <mceier@gmail.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1. Rewrite of the non-dma data transfer functions to use only ONE mode
of TIMOD (TIMOD=0x1). With TIMOD=0, it was not possible to set the TX
bit pattern. So the TDBR = 0xFFFF inside the read calls won't work.
2. Clear SPI_RDBR before reading and before duplex transfer.
Otherwise the garbage data in RDBR will get read. Since mmc_spi uses a
lot of duplex transfers, this is the main cause of mmc_spi failure.
3. Poll RXS for transfer completion. Polling SPIF or TXS cannot
guarantee transfer completion. This may interrupt a transfer before it
is finished. Also this may leave garbage data in buffer and affect
next transfer.
[Yi Li <yi.li@analog.com>: add a field "u16 idle_tx_val" in "struct
bfin5xx_spi_chip" to specify the value to transmit if no TX value
is supplied.]
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for GPIO controlled SPI Chip Selects. To make use of this
feature, set chip_select = 0 and add a proper cs_gpio to your
controller_data.
struct spi_board_info
.chip_select = 0
struct bfin5xx_spi_chip
.cs_gpio = GPIO_P###
There are various SPI devices that require SPI MODE_0, and need to have
the Chip Selects asserted during the entire transfer. Consider using
SPI_MODE_3 (SPI_CPHA | SPI_CPOL) if your device allows it.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Do this because when things crash, we get simple names like "setup" and
"start_queue" which is pretty difficult to trace back to the real thing:
the spi driver
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to comments in linux/spi/spi.h:
* All SPI transfers start with the relevant chipselect active. Normally
* it stays selected until after the last transfer in a message. Drivers
* can affect the chipselect signal using cs_change.
*
* (i) If the transfer isn't the last one in the message, this flag is
* used to make the chipselect briefly go inactive in the middle of the
* message. Toggling chipselect in this way may be needed to terminate
* a chip command, letting a single spi_message perform all of group of
* chip transactions together.
*
* (ii) When the transfer is the last one in the message, the chip may
* stay selected until the next transfer. On multi-device SPI busses
* with nothing blocking messages going to other devices, this is just
* a performance hint; starting a message to another device deselects
* this one. But in other cases, this can be used to ensure correctness.
* Some devices need protocol transactions to be built from a series of
* spi_message submissions, where the content of one message is determined
* by the results of previous messages and where the whole transaction
* ends when the chipselect goes intactive.
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This bug can be observed when two SPI devices are sharing the spi bus: One
device is set as SPI CS 7, another one is using SPI CS 4.
In spi_bfin5xx.c: cs_active(), cs_deactive() are used to control SPI_FLG
register. From the debug bellow:
cs_active: flag: 0x7f91, chip->flag: 0x7f80, cs: 7
cs_active: flag: 0xef91, chip->flag: 0xef10, cs: 4
When device A (cs_7) activate CS 7, SPI_FLG is set as 0x7f91 (however,
SPI_FLG should be set as 0x7f80, or 0x6f91 if in broadcast mode).
Due to some HW bug (very possibly), if SPI_FLG is set as 0x7f91, SPISSEL7
is asserted, however SPISSEL4 will be asserted too (I can see this using
the scope). This is unreasonable according to HRM.
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Without this change, SPI DMA is not reliably under stress tests.
Obiviously it's a hardware issue which is not addressed by any document.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The "while" endless loop will cause the system hang if hardware error, so
we add timeout control to make the system alive.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When using a BF533-STAMP here with a W25X10 SPI flash. It works fine when
enable_dma is disabled, but doesn't work at all when turning DMA on. We
get just 0xff bytes back when trying to read the device.
Change the code around so that it programs the SPI first and then enables
DMA, it seems to work a lot better ...
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
use the properl BIT_CTL_... defines rather than the internal driv er
CFG_SPI_... defines
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We only need to check SPI error when DMA failes, cause that is the DMA IRQ
handling routine.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Because of DMA hardware issue, we were trying to use software workaround.
This patch add some useful debug messages to help us debugging the DMA
code.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Blackfin's related DMA callback API doesn't need void * cast, so drop it.
And this driver is for all Blackfin processors not only for BF53x, we
update the DMA request label for more meaningful information.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For DMA TX/RX operation in pump_transfers, DMA contriguration code in TX
and RX paths are almost the same. This patch unify the duplicated DMA
code to make it more readable.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the SPI bus registers a receive overflow error, pass the result back up
to the higher levels.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use len_in_bytes when we care about the number of bytes transferred rather
than the number of spi transactions. (this value will be the same for
8bit transfers, but not any other sizes)
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We already moved bfin_addr_dcachable() and friends into the cacheflush
header where it belongs, so don't need to include <asm/cplbinit.h> here.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix erroneous SPI Clock divisor calculation. Make sure SPI_BAUD is always
>= 2. Writing a value of 0 or 1 to the SPI_BAUD register disables the
serial clock.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Flush or invalidate caches before doing DMA transfer, if needed.
[Mike Frysinger <vapier.adi@gmail.com>: add comment to address the
issue "Full duplex only works for non-DMA transfers".]
Signed-off-by: Vitja Makarov <vitja.makarov@gmail.com>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This controller can be found on the D-Link DNS-323 for instance, where
it is to be configured via static i2c_board_info in the board-specific
mach-orion/dns323-setup.c; this driver supports only the new-style
driver model.
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Matthew Palmer <mpalmer@debian.org>
Signed-off-by: Laurie Bradshaw <bradshaw.laurie@googlemail.com>
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Not critical.
WARNING: drivers/char/esp.o(.text+0x278): Section mismatch in reference from the function show_serial_version() to the variable .init.data:serial_version
The function show_serial_version() references
the variable __initdata serial_version.
This is often because show_serial_version lacks a __initdata
annotation or the annotation of serial_version is wrong.
WARNING: drivers/char/esp.o(.text+0x27d): Section mismatch in reference from the function show_serial_version() to the variable .init.data:serial_name
The function show_serial_version() references
the variable __initdata serial_name.
This is often because show_serial_version lacks a __initdata
annotation or the annotation of serial_name is wrong.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Andrew J. Robinson <arobinso@nyx.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (28 commits)
powerpc: Fix oops when loading modules
powerpc: Wire up preadv and pwritev
powerpc/ftrace: Fix printf format warning
powerpc/ftrace: Fix #if that should be #ifdef
powerpc: Fix ptrace compat wrapper for FPU register access
powerpc: Print information about mapping hw irqs to virtual irqs
powerpc: Correct dependency of KEXEC
powerpc: Disable VSX or current process in giveup_fpu/altivec
powerpc/pseries: Enable relay in pseries_defconfig
powerpc/pseries: Fix ibm,client-architecture comment
powerpc/pseries: Scan for all events in rtasd
powerpc/pseries: Add dispatch dispersion statistics
powerpc: Clean up some prom printouts
powerpc: Print progress of ibm,client-architecture method
powerpc: Remove duplicated #include's
powerpc/pmac: Fix internal modem IRQ on Wallstreet PowerBook
powerpc/wdrtas: Update wdrtas_get_interval to use rtas_data_buf
fsl-diu-fb: Pass the proper device for dma mapping routines
powerpc/pq2fads: Update device tree for use with device-tree-aware u-boot.
cpm_uart: Disable CPM udbg when re-initing CPM uart, even if not the console.
...
Asus boards have an ACPI interface for interacting with the hwmon (fan,
temperatures, voltages) subsystem; this driver exposes the relevant
information via the standard sysfs interface.
There are two different ACPI interfaces:
- an old one (based on RVLT/RFAN/RTMP)
- a new one (GGRP/GITM)
Both may be present but there a few cases (my board, sigh) where the
new interface is just an empty stub; the driver defaults to the old one
when both are present.
The old interface has received a considerable testing, but I'm still
awaiting confirmation from my tester that the new one is working as
expected (hence the debug code is still enabled).
Currently all the attributes are read-only, though a (partial) control
should be possible with a bit more work.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The legacy i2c binding model is going away really soon now, so convert
the lm95241 driver to the new binding model or it will break.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Davide Rizzo <elpa.rizzo@gmail.com>
mount/1865 is trying to release lock (&lo->lo_ctl_mutex) at:
but there are no more locks to release!
mutex is already unlocked in loop_clr_fd(), we should not
try to unlock it in lo_release() again.
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
'disable_delay' was static which is wrong as it is calculated using the per-device
bus speed. This patch turns 'disable_delay' into a per-device variable.
Reported-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Support for the s6000 on-chip i2c controller.
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch makes the I2C bus speed configurable by using the I2C node
property "clock-frequency". If the property is not defined, the old
fixed clock settings will be used for backward comptibility.
The generic I2C clock properties, especially the CPU-specific source
clock pre-scaler are defined via the OF match table:
static const struct of_device_id mpc_i2c_of_match[] = {
...
{.compatible = "fsl,mpc8543-i2c",
.data = &(struct fsl_i2c_match_data) {
.setclock = mpc_i2c_setclock_8xxx,
.prescaler = 2,
},
},
The "data" field defines the relevant I2C setclock function and the
relevant pre-scaler for the I2C source clock frequency.
It uses arch-specific tables and functions to determine resonable
Freqency Divider Register (fdr) values for MPC83xx, MPC85xx, MPC86xx,
MPC5200 and MPC5200B.
The i2c->flags field and the corresponding FSL_I2C_DEV_* definitions
have been removed as they are obsolete.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch used the dev_dbg, dev_err, etc. functions for debug
and error output instead of printk and pr_debug.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix errors reported by checkpatch (indention, long lines, trailing
white space, etc.).
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
[ben-linux@fluff.org: fix minor patch fault in remove]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This is required in order to ensure that core system devices such as
voltage regulators attached via I2C are avaiable early in boot.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The platform data for the i2c-s3c2410 driver used to allow a min,
max and desired frequency for the I2C bus. This patch reduces it
to simply a desired frequency ceiling and corrects all the uses
of the platform data appropriately.
This means, for example, that on a system with a 66MHz fclk, a
request for 100KHz will achieve 65KHz which is safe and
acceptable, rather than 378KHz which it would have achieved
without this change.
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Daniel Silverstone <dsilvers@simtec.co.uk>
[ben-linux@fluff.org: tidy subject and description]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The sda_delay field should be specified in ns, not in clock ticks
as when using cpufreq we could be changing the bus rate.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Implementation of I2C Adapter/Algorithm Driver for I2C Bus integrated
in Freescale's i.MX/MXC processors.
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This driver supports mflash IO mode for linux.
Mflash is embedded flash drive and mainly targeted mobile and consumer
electronic devices.
Internally, mflash has nand flash and other hardware logics and supports 2
different operation (ATA, IO) modes. ATA mode doesn't need any new driver
and currently works well under standard IDE subsystem. Actually it's one
chip SSD. IO mode is ATA-like custom mode for the host that doesn't have
IDE interface.
Followings are brief descriptions about IO mode.
A. IO mode based on ATA protocol and uses some custom command. (read confirm,
write confirm)
B. IO mode uses SRAM bus interface.
C. IO mode supports 4kB boot area, so host can boot from mflash.
This driver is quitely similar to a standard ATA driver, but because of
following reasons it is currently seperated with ATA layer.
1. ATA layer deals standard ATA protocol. ATA layer have many low-
level device specific interface, but data transfer keeps ATA rule.
But, mflash IO mode doesn't.
2. Even though currently not used in mflash driver code, mflash has
some custom command and modes. (nand fusing, firmware patch, etc) If
this feature supported in linux kernel, ATA layer more altered.
3. Currently PATA platform device driver doesn't support interrupt.
(I'm not sure) But, mflash uses interrupt (polling mode is just for
debug).
4. mflash is somewhat under-develop product. Even though some company
already using mflash their own product, I think more time is needed for
standardization of custom command and mode. That time (maybe October)
I will talk to with ATA people. If they accept integration, I will
integrate.
Signed-off-by: unsik Kim <donari75@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Add a method for discovering the first memory BAR. All Smart Array
controllers to date have always had the the memory BAR as the first BAR.
A new controller to be released later this year breaks that model.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The MSA2012 cannot inform the driver of configuration changes since all
management is out of band. This is a departure from any storage we have
supported in the past. We need some way to detect changes on the topology
so we implement this kernel thread. In some instances there's nothing we
can do from the driver (like LUN failure) so just print out a message. In
the case where logical volumes are added or deleted we call
rebuild_lun_table to refresh the driver's view of the world.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
We must complete the full request, so store the request count and then set
the ->data_len to the residual count from the hardware.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Fix this sparse warning:
drivers/platform/x86/panasonic-laptop.c:273:70: warning: Using plain integer as NULL pointer
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: Len Brown <len.brown@intel.com>
The exact offset between Kelvin and degree Celsius is 273.15. However
ACPI handles temperature values with a single decimal place. As a
consequence, some implementations use an offset of 273.1 and others
use an offset of 273.2. Try to find out which one is being used, to
present the most accurate and visually appealing number.
Tested on a Sony Vaio PGC-GR214EP (which uses 273.1) and a Lenovo
Thinkpad T60p (which uses 273.2).
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The (relatively) new pmac_zilog driver doesn't use the pre-munged
IRQ numbers from the macio_dev unlike other macio things, it
directly maps it off the OF device-tree.
It does that because it can be initialized much earlier than the
registration of the macio devices, in order to get a serial
console early.
Unfortunately, that means that it "misses" some fixups done
by the macio layer to work around missing interrupt descriptions
in the device-tree of the Wallstreet machines.
This patch brings the necessary workaround into the pmac_zilog
driver itself to bring it back to working condition.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The buffer passed to the ibm,get-system-parameter RTAS call must be
in the RMA. To ensure we pass an address in the RMA use rtas_data_buf
for the actual RTAS call and then copy the result to value. We can't
just make it static because this can be compiled in as a module.
Also add the WDRTAS_SP_SPI_LEN so we don't litter '4' throughout the
function.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Tested-by: Adrian Reber <adrian@lisas.de>
Acked-by: Utz Bacher <utz.bacher@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
