If either uartclk or baud are 0, avoid calculating and setting a divisor
based on them since the output will almost certainly be garbage.
This also allows platforms such as the MIPS generic kernel, which has no
way to know a valid BASE_BASE for the board it is actually booted on at
compile time, to set BASE_BAUD to 0 and avoid early_8250 setting a bad
divisor.
This fixes a regression caused by commit 31cb9a8575 ("earlycon:
initialise baud field of earlycon device structure"), which changed the
behavior of of_setup_earlycon such that it sets a baud rate in the
earlycon structure where previously it was left as 0. All boards
supported by the MIPS generic kernel started outputting garbage from the
boot console due to an incorrect divisor being set.
Fixes: 31cb9a8575 ("earlycon: initialise baud field of earlycon device structure")
Cc: stable <stable@vger.kernel.org> # 4.14
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device will be used in future Amazon EC2 instances as the primary
serial port (i.e., data sent to this port will be available via the
GetConsoleOuput [1] EC2 API).
[1] http://docs.aws.amazon.com/AWSEC2/latest/APIReference/API_GetConsoleOutput.html
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Matt Wilson <msw@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since imx_disable_rx_int is only called by imx_startup,
let's integrate it into that function. Notice UCR2_ATEN is
never set by the driver. The bit is still cleaned to make
this patch a noop.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 075167ed71 ("drivers: PL011: replace UART_MIS reading with
_RIS & _IMSC") amended this driver's interrupt handler to read the
Raw Interrupt Status (RIS) and Interrupt Mask Set/Clear (IMSC) registers
instead of the Masked Interrupt Status (MIS) register. The change was
made to attain compatibility with SBSA UARTs which lack the MIS register.
However the IMSC register is cached by the driver. Using the cached
copy saves one register read per interrupt.
I've tested this change successfully on a BCM2837 (Raspberry Pi CM3).
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Cc: Phil Elwell <phil@raspberrypi.org>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Mark Langsdorf <mlangsdo@redhat.com>
Cc: Naresh Bhat <nbhat@cavium.com>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pl011_fifo_to_tty() has two counters (max_count and fifotaken) for the
same loop. One counter should suffice. This saves one subtraction per
character read from the RX FIFO.
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Cc: Phil Elwell <phil@raspberrypi.org>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This simply fixes a typo in the preprocessor macros. No functional
changes intended.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the code there are two separate sections which each describe some of
the bits in the AML_UART_CONTROL register.
Merge these into one section to make the code easier to read.
No functional changes intended.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "clear error" bit in the AML_UART_CONTROL register is defined twice.
Remove the AML_UART_CLR_ERR definition and replace it with
AML_UART_CLEAR_ERR.
AML_UART_CLEAR_ERR was chosen to be kept since the datasheet's
description for this bit is "Clear Error" (so developer's don't have to
translate this to "CLR_ERR").
No functional changes intended.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With all callbacks converted, and the timer callback prototype
switched over, the TIMER_FUNC_TYPE cast is no longer needed,
so remove it. Conversion was done with the following scripts:
perl -pi -e 's|\(TIMER_FUNC_TYPE\)||g' \
$(git grep TIMER_FUNC_TYPE | cut -d: -f1 | sort -u)
perl -pi -e 's|\(TIMER_DATA_TYPE\)||g' \
$(git grep TIMER_DATA_TYPE | cut -d: -f1 | sort -u)
The now unused macros are also dropped from include/linux/timer.h.
Signed-off-by: Kees Cook <keescook@chromium.org>
Summary of modules changes for the 4.15 merge window:
- Treewide module_param_call() cleanup, fix up set/get function
prototype mismatches, from Kees Cook
- Minor code cleanups
Signed-off-by: Jessica Yu <jeyu@kernel.org>
-----BEGIN PGP SIGNATURE-----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=c8vb
-----END PGP SIGNATURE-----
Merge tag 'modules-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux
Pull module updates from Jessica Yu:
"Summary of modules changes for the 4.15 merge window:
- treewide module_param_call() cleanup, fix up set/get function
prototype mismatches, from Kees Cook
- minor code cleanups"
* tag 'modules-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
module: Do not paper over type mismatches in module_param_call()
treewide: Fix function prototypes for module_param_call()
module: Prepare to convert all module_param_call() prototypes
kernel/module: Delete an error message for a failed memory allocation in add_module_usage()
These are the main MIPS changes for 4.15.
Fixes:
- ralink: Fix MT7620 PCI build issues (4.5)
- Disable cmpxchg64() and HAVE_VIRT_CPU_ACCOUNTING_GEN for 32-bit SMP
(4.1)
- Fix MIPS64 FP save/restore on 32-bit kernels (4.0)
- ptrace: Pick up ptrace/seccomp changed syscall numbers (3.19)
- ralink: Fix MT7628 pinmux (3.19)
- BCM47XX: Fix LED inversion on WRT54GSv1 (3.17)
- Fix n32 core dumping as o32 since regset support (3.13)
- ralink: Drop obsolete USB_ARCH_HAS_HCD select
Build system:
- Default to "generic" (multiplatform) system type instead of IP22
- Use generic little endian MIPS32 r2 configuration as default defconfig
instead of ip22_defconfig
FPU emulation:
- Fix exception generation for certain R6 FPU instructions
SMP:
- Allow __cpu_number_map to be larger than NR_CPUS for sparse CPU id
spaces
Miscellaneous:
- Add iomem resource for kernel bss section for kexec/kdump
- Atomics: Nudge writes on bit unlock
- DT files: Standardise "ok" -> "okay"
Platform support:
BMIPS:
- Enable HARDIRQS_SW_RESEND
Broadcom BCM63XX:
- Add clkdev lookup support
- Update clk driver, UART driver, DTs to handle named refclk from DTs
- Split apart various clocks to more closely match hardware
- Add ethernet clocks
Cavium Octeon:
- Remove usage of cvmx_wait() in favour of __delay()
ImgTec Pistachio:
- DT: Drop deprecated dwmmc num-slots property
Ingenic JZ4780:
- Add NFS root to Ci20 defconfig
- Add watchdog to Ci20 DT & defconfig, and allow building of watchdog
driver with this SoC
Generic (multiplatform):
- Migrate xilfpga (MIPSfpga) platform to the generic platform
Lantiq xway:
- Fix ASC0/ASC1 clocks
Minor cleanups:
- Define virt_to_pfn()
- Make thread_saved_pc static
- Simplify 32-bit sign extension in __read_64bit_c0_split()
- DMA: Use vma_pages() helper
- FPU emulation: Replace unsigned with unsigned int
- MM: Removed unused lastpfn
- Alchemy: Make clk_ops const
- Lasat: Use setup_timer() helper
- ralink: Use BIT() in MT7620 PCI driver
-----BEGIN PGP SIGNATURE-----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=xbL0
-----END PGP SIGNATURE-----
Merge tag 'mips_4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips
Pull MIPS updates from James Hogan:
"These are the main MIPS changes for 4.15.
Fixes:
- ralink: Fix MT7620 PCI build issues (4.5)
- Disable cmpxchg64() and HAVE_VIRT_CPU_ACCOUNTING_GEN for 32-bit SMP
(4.1)
- Fix MIPS64 FP save/restore on 32-bit kernels (4.0)
- ptrace: Pick up ptrace/seccomp changed syscall numbers (3.19)
- ralink: Fix MT7628 pinmux (3.19)
- BCM47XX: Fix LED inversion on WRT54GSv1 (3.17)
- Fix n32 core dumping as o32 since regset support (3.13)
- ralink: Drop obsolete USB_ARCH_HAS_HCD select
Build system:
- Default to "generic" (multiplatform) system type instead of IP22
- Use generic little endian MIPS32 r2 configuration as default
defconfig instead of ip22_defconfig
FPU emulation:
- Fix exception generation for certain R6 FPU instructions
SMP:
- Allow __cpu_number_map to be larger than NR_CPUS for sparse CPU id
spaces
Miscellaneous:
- Add iomem resource for kernel bss section for kexec/kdump
- Atomics: Nudge writes on bit unlock
- DT files: Standardise "ok" -> "okay"
Minor cleanups:
- Define virt_to_pfn()
- Make thread_saved_pc static
- Simplify 32-bit sign extension in __read_64bit_c0_split()
- DMA: Use vma_pages() helper
- FPU emulation: Replace unsigned with unsigned int
- MM: Removed unused lastpfn
- Alchemy: Make clk_ops const
- Lasat: Use setup_timer() helper
- ralink: Use BIT() in MT7620 PCI driver
Platform support:
BMIPS:
- Enable HARDIRQS_SW_RESEND
Broadcom BCM63XX:
- Add clkdev lookup support
- Update clk driver, UART driver, DTs to handle named refclk from DTs
- Split apart various clocks to more closely match hardware
- Add ethernet clocks
Cavium Octeon:
- Remove usage of cvmx_wait() in favour of __delay()
ImgTec Pistachio:
- DT: Drop deprecated dwmmc num-slots property
Ingenic JZ4780:
- Add NFS root to Ci20 defconfig
- Add watchdog to Ci20 DT & defconfig, and allow building of watchdog
driver with this SoC
Generic (multiplatform):
- Migrate xilfpga (MIPSfpga) platform to the generic platform
Lantiq xway:
- Fix ASC0/ASC1 clocks"
* tag 'mips_4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips: (46 commits)
MIPS: Add iomem resource for kernel bss section.
MIPS: cmpxchg64() and HAVE_VIRT_CPU_ACCOUNTING_GEN don't work for 32-bit SMP
MIPS: BMIPS: Enable HARDIRQS_SW_RESEND
MIPS: pci: Make use of the BIT() macro inside the mt7620 driver
MIPS: pci: Remove KERN_WARN instance inside the mt7620 driver
MIPS: pci: Remove duplicate define in mt7620 driver
MIPS: ralink: Fix typo in mt7628 pinmux function
MIPS: ralink: Fix MT7628 pinmux
MIPS: Fix odd fp register warnings with MIPS64r2
watchdog: jz4780: Allow selection of jz4740-wdt driver
MIPS/ptrace: Update syscall nr on register changes
MIPS/ptrace: Pick up ptrace/seccomp changed syscalls
MIPS: Fix an n32 core file generation regset support regression
MIPS: Fix MIPS64 FP save/restore on 32-bit kernels
MIPS: page.h: Define virt_to_pfn()
MIPS: Xilfpga: Switch to using generic defconfigs
MIPS: generic: Add support for MIPSfpga
MIPS: Set defconfig target to a generic system for 32r2el
MIPS: Kconfig: Set default MIPS system type as generic
MIPS: DTS: Remove num-slots from Pistachio SoC
...
Here is the big tty/serial driver pull request for 4.15-rc1.
Lots of serial driver updates in here, some small vt cleanups, and a
raft of SPDX and license boilerplate cleanups, messing up the diffstat a
bit.
Nothing major, with no realy functional changes except better hardware
support for some platforms.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgnD+w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynAmgCfSSr/9qiCE0vfP5eVYjddzxfWyZ4AoMbKORZC
5x2KVW0Btrbs3WmnD7ZU
=PSea
-----END PGP SIGNATURE-----
Merge tag 'tty-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the big tty/serial driver pull request for 4.15-rc1.
Lots of serial driver updates in here, some small vt cleanups, and a
raft of SPDX and license boilerplate cleanups, messing up the diffstat
a bit.
Nothing major, with no realy functional changes except better hardware
support for some platforms.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (110 commits)
tty: ehv_bytechan: fix spelling mistake
tty: serial: meson: allow baud-rates lower than 9600
serial: 8250_fintek: Fix crash with baud rate B0
serial: 8250_fintek: Disable delays for ports != 0
serial: 8250_fintek: Return -EINVAL on invalid configuration
tty: Remove redundant license text
tty: serdev: Remove redundant license text
tty: hvc: Remove redundant license text
tty: serial: Remove redundant license text
tty: add SPDX identifiers to all remaining files in drivers/tty/
tty: serial: jsm: remove redundant pointer ts
tty: serial: jsm: add space before the open parenthesis '('
tty: serial: jsm: fix coding style
tty: serial: jsm: delete space between function name and '('
tty: serial: jsm: add blank line after declarations
tty: serial: jsm: change the type of local variable
tty: serial: imx: remove dead code imx_dma_rxint
tty: serial: imx: disable ageing timer interrupt if dma in use
serial: 8250: fix potential deadlock in rs485-mode
serial: m32r_sio: Drop redundant .data assignment
...
Devices like DCF77 receivers need the baud-rate to be as low as 50.
I have tested this on a Meson GXL device with uart_A.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: linux-amlogic@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Thomas Rohloff <v10lator@myway.de>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250_fintek.c is support the Fintek F81866/F81216 with dynamic clock.
But It'll generate "division by zero" exception and crash in
fintek_8250_set_termios() with baud rate 0 on baudrate_table[i] % baud.
It can be tested with following C code:
...
struct termios options;
tcgetattr(fd, &options);
...
options.c_cflag = CS8 | CREAD; /* baud rate 0 */
tcsetattr(fd, TCSANOW, &options);
tcflush(fd, TCIOFLUSH);
Fixes: 195638b6d4 ("serial: 8250_fintek: UART dynamic clocksource on Fintek F81866")
Reported-by: Lukas Redlinger <rel+kernel@agilox.net>
Cc: Lukas Redlinger <rel+kernel@agilox.net>
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the datasheet, only the first port supports delay before
send and delay after send.
Reported-by: "Ji-Ze Hong (Peter Hong)" <hpeter@gmail.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hardware does not support having the same RTS level during RX and TX
when RS485 mode is on (URA in Fintek terminology).
The manufacturer has also confirmed that the delays are not enabled if
the RS485 mode is not enabled.
Therefore we should return -EINVAL if the user wants to have the same
value for RTS_ON_SEND and RTS_AFTER_SEND.
Cc: "Ji-Ze Hong (Peter Hong)" <hpeter@gmail.com>
Cc: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all tty files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Joachim Eastwood <manabian@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Pat Gefre <pfg@sgi.com>
Cc: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Timur Tabi <timur@tabi.org>
Cc: Tony Prisk <linux@prisktech.co.nz>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/tty files files with the correct SPDX license
identifier based on the license text in the file itself. The SPDX
identifier is a legally binding shorthand, which can be used instead of
the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Joachim Eastwood <manabian@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Cc: "Uwe Kleine-König" <kernel@pengutronix.de>
Cc: Pat Gefre <pfg@sgi.com>
Cc: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Timur Tabi <timur@tabi.org>
Cc: Tony Prisk <linux@prisktech.co.nz>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pointer ts is assigned a value that is never read, ts is therefore
redundant and can be removed. Cleans up clang warning:
drivers/tty/serial/jsm/jsm_tty.c:285:2: warning: Value stored to 'ts'
is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the checkpatch.pl complains:
space required before the open parenthesis '('.
Signed-off-by: Gimcuan Hui <gimcuan@gmail.com>
Acked-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes checkpatch.pl warning:
space prohibited between function name and open parenthesis '('.
Signed-off-by: Gimcuan Hui <gimcuan@gmail.com>
Acked-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes checkpatch.pl warning:
Missing a blank line after declarations.
Signed-off-by: Gimcuan Hui <gimcuan@gmail.com>
Acked-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The return type of jsm_get_mstat was int, and the local var result
was for the return should be int, make the change.
This patch fixes the checkpatch.pl warning:
Prefer 'unsigned int' to bare use of 'unsigned'.
Signed-off-by: Gimcuan Hui <gimcuan@gmail.com>
Acked-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Codify using a named clock for the refclk of the uart. This makes it
easier if we might need to add a gating clock (like present on the
BCM6345).
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: linux-mips@linux-mips.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-serial@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: bcm-kernel-feedback-list@broadcom.com
Patchwork: https://patchwork.linux-mips.org/patch/17328/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: James Hogan <jhogan@kernel.org>
Since commit 4dec2f119e ("imx-serial: RX DMA startup latency")
the interrupt routine no longer will start rx dma.
imx_dma_rxint no longer needs to be called to try and start dma.
It won't start dma because dma_is_rxing is
already true meaning dma is already started.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 4dec2f119e ("imx-serial: RX DMA startup latency")
the interrupt routine no longer will start rx dma.
So, we no longer need to enable this interrupt to start dma.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Canceling hrtimer when holding uart spinlock can deadlock.
CPU0: syscall write
-> get uart port spinlock
-> write uart
-> start_tx_rs485
-> hrtimer_cancel
-> wait for hrtimer callback to finish
CPU1: hrtimer IRQ
-> run hrtimer
-> em485_handle_stop_tx
-> get uart port spinlock
CPU0 is waiting for the hrtimer callback to finish, but the hrtimer
callback running on CPU1 is waiting to get the uart port spinlock.
This deadlock can be avoided by not canceling the hrtimers in these paths.
Setting active_timer=NULL can be done without accessing hrtimer,
and that will effectively cancel operations that would otherwise have been
performed by the hrtimer callback.
Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the timer converted to using the new timer_setup()/from_timer() API,
setting the .data field is redundant (and the field will be removed soon),
so drop it.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During hibernation, freeze/thaw/restore dev_pm_ops are called instead of
suspend/resume. Hook up the hibernation ops. The _noirq parts are
identical, but suspend/resume are replaced with variants that do not
enable wakeup from i.MX UART. There is no need to restore register
contents in thaw_noirq.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Back in 2010, commit 3b43816f68 ("ARM: 5933/1: amba-pl011: support
hardware flow control") added an autorts flag to this driver to store
whether automatic hardware flow control is requested.
In 2015, commit 391f93f2ec ("serial: core: Rework hw-assisted flow
control support") added a flag with identical functionality to generic
code.
Switch over to that flag and drop the driver-specific one.
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver's ->rs485_config callback checks if SER_RS485_RTS_ON_SEND
and SER_RS485_RTS_AFTER_SEND have the same value. If they do, it means
the user has passed in invalid data with the TIOCSRS485 ioctl()
since RTS must have a different polarity when sending and when not
sending. In this case, rs485 mode is not enabled (the RS485_URA bit
is not set in the RS485 Enable Register) and this is supposed to be
signaled back to the user by clearing the SER_RS485_ENABLED bit in
struct serial_rs485 ... except a missing tilde character is preventing
that from happening.
Fixes: 28e3fb6c4d ("serial: Add support for Fintek F81216A LPC to 4 UART")
Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Cc: "Ji-Ze Hong (Peter Hong)" <hpeter@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The final assignment to port is never read, hence it is redundant
and can be removed. Also move the declaration of port to a more
local scope. Cleans up clang warning:
drivers/tty/serial/serial_core.c:1498:2: warning: Value stored
to 'port' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SCSCR register access in sci_break_ctl() is not locked.
sci_start_tx() and sci_set_termios() changes the SCSCR register,
but does not lock sci_port.
Therefore, this patch adds lock during register access.
Also, remove the log output that leads to a double lock.
Some analysis of where locks are not taken is as follows.
It appears that the lock is not taken in:
- sci_start_tx(), sci_stop_tx() as this is installed as a callback.
And all callers of the callback take the lock.
- start_rx as callers take the lock.
- stop_rx. this is both installed as a callback and called directly.
In both cases the caller takes the lock.
Signed-off-by: Takatoshi Akiyama <takatoshi.akiyama.kj@ps.hitachi-solutions.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gcc points out that the length passed into memset here is wrong:
drivers/tty/serial/mvebu-uart.c: In function 'mvebu_uart_probe':
arch/x86/include/asm/string_32.h:324:29: error: 'memset' used with length equal to number of elements without multiplication by element size [-Werror=memset-elt-size]
Moreover, the structure was allocated with kzalloc a few lines earlier,
so that memset is also unnecessary. Let's drop it to shut up the
compiler warning.
Fixes: 95f787685a ("serial: mvebu-uart: dissociate RX and TX interrupts")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable rts is being assigned but it is never read, hence it can be
removed. The assignment to param_new to zero is redundant as it is
being updates a few statements later, so remove this redundant
assignment. Cleans up two clang warnings:
drivers/tty/serial/max3100.c:277:3: warning: Value stored to 'rts'
is never read
drivers/tty/serial/max3100.c:439:2: warning: Value stored to 'param_new'
is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Cc: nios2-dev@lists.rocketboards.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: adi-buildroot-devel@lists.sourceforge.net
Cc: linux-serial@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Ed Blake <ed.blake@imgtec.com>
Cc: Matthias Brugger <mbrugger@suse.com>
Cc: Sean Young <sean@mess.org>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several function prototypes for the set/get functions defined by
module_param_call() have a slightly wrong argument types. This fixes
those in an effort to clean up the calls when running under type-enforced
compiler instrumentation for CFI. This is the result of running the
following semantic patch:
@match_module_param_call_function@
declarer name module_param_call;
identifier _name, _set_func, _get_func;
expression _arg, _mode;
@@
module_param_call(_name, _set_func, _get_func, _arg, _mode);
@fix_set_prototype
depends on match_module_param_call_function@
identifier match_module_param_call_function._set_func;
identifier _val, _param;
type _val_type, _param_type;
@@
int _set_func(
-_val_type _val
+const char * _val
,
-_param_type _param
+const struct kernel_param * _param
) { ... }
@fix_get_prototype
depends on match_module_param_call_function@
identifier match_module_param_call_function._get_func;
identifier _val, _param;
type _val_type, _param_type;
@@
int _get_func(
-_val_type _val
+char * _val
,
-_param_type _param
+const struct kernel_param * _param
) { ... }
Two additional by-hand changes are included for places where the above
Coccinelle script didn't notice them:
drivers/platform/x86/thinkpad_acpi.c
fs/lockd/svc.c
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Commit 348f9bb31c ("serial: omap: Fix RTS handling") sought to enable
auto RTS upon manual RTS assertion and disable it on deassertion.
However it seems the latter was done incorrectly, it clears all bits in
the Extended Features Register *except* auto RTS.
Fixes: 348f9bb31c ("serial: omap: Fix RTS handling")
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The do .. while loop checks for interrupt pending at the
start of the loop and exits if there is none, it then
checks again for this condition at the end of the loop.
Signed-off-by: Martin Townsend <mtownsend1973@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Define the missing register offsets and bit fields for the extended
UART port. Add a second driver data structure filled with its port data,
selected with the right compatible (marvell,armada-3700-uart-ext).
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A3700 boards may have up to two UART ports. Set the new limit to two
maximum UART ports.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While the standard UART port can use a single IRQ that 'sums' both RX
and TX interrupts, the extended port cannot and has to use two different
ISR, one for each direction. The standard port also has the hability
to use two separate interrupts (one for each direction).
The logic is then: either there is only one unnamed interrupt on the
standard port and this interrupt must be used for both directions
(this is legacy bindings); or all the interrupts must be described and
named 'uart-sum' (if available), 'uart-rx', 'uart-tx' and two separate
handlers for each direction will be used.
Suggested-by: Allen Yan <yanwei@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pulse interrupts (extended UART only) needs a change of state to trigger
the TX interrupt. In addition to enabling the TX_READY_INT_EN flag,
produce a FIFO state change from 'empty' to 'not full'. For this, write
only one data byte in TX start, making the TX FIFO not empty, and wait
for the TX interrupt to continue the transfer.
Signed-off-by: Allen Yan <yanwei@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When receiving data on RX pin before ->uart_startup() is called, some
error bits in the state register could be set up (like BRK_DET).
This is harmless when using only the standard UART (error bits are
read-only), but may procude an endless loop once in the extended UART
RX interrupt handler (error bits must be cleared).
Clear the status register in ->uart_startup() to avoid this situation.
Signed-off-by: Allen Yan <yanwei@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Until now, the first UART port baudrate was set by the bootloader.
Add a function allowing to change the baudrate. Changes may be done
from userspace but also at probe time by the kernel. Use the simplest
method: baudrate divisor.
Works for all UART ports until 230400 baud. To achieve higher baudrates,
software should implement the fractional divisor feature that allows
more accuracy for higher rates.
Signed-off-by: Allen Yan <yanwei@marvell.com>
[<miquel.raynal@free-electrons.com>: changed termios handling]
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The existing UART driver relies on the bootloader to initialize the
port(s). However, the secondary uart port may not be initialized
properly in early boot stage. This patch adds the UART soft reset when
probing, for all ports.
Signed-off-by: Allen Yan <yanwei@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two UART ports on Armada3700. The second UART is based on the
first one, plus additional features, but it has a different register
layout (some bit fields are also moved inside the registers).
Clearly separate register offsets and bit fields that differ between the
standard and the extended IP. Access them in a generic way. Rename the
defines with the "STD" prefix for future distinction with "EXT" defines.
Point to these defines in the main driver data structure.
The early console only uses the standard port (not extended).
Suggested-by: Wilson Ding <dingwei@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Until now, the mvebu-uart driver only supported probing a single UART
port. However, some platforms have multiple instances of this UART
controller, and therefore the driver should support multiple ports.
In order to achieve this, we make sure to assign port->line properly,
instead of hardcoding it to zero.
Signed-off-by: Allen Yan <yanwei@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the driver name when requesting an interrupt for consistency.
Avoids possible confusion with DW8250 driver interrupt names in
/proc/interrupts.
Signed-off-by: Yehuda Yitschak <yehuday@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pr_err() messages should end with a new-line to avoid other messages
being concatenated.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Russell King <linux@armlinux.org.uk>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SuperIO will be configured at boot time by BIOS, but some BIOS
will not deactivate the SuperIO when the end of configuration. It'll
lead to mismatch for pdata->base_port in probe_setup_port(). So we'll
deactivate all SuperIO before activate special base_port in
fintek_8250_enter_key().
Tested on iBASE MI802.
Cc: stable@vger.kernel.org
Tested-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Reviewd-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The upper four bits of the XR17V35x fractional divisor register (DLD)
control general chip function (RS-485 direction pin polarity, multidrop
mode, XON/XOFF parity check, and fast IR mode). Don't allow these bits
to be clobbered when setting the baudrate.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The __init attribute is meant to mark functions, use __initdata instead
for the data structure.
This fixes the following error when building with clang:
drivers/tty/serial/sh-sci.c:3247:15: error: '__section__' attribute only
applies to functions, methods, properties, and global variables
static struct __init plat_sci_port port_cfg;
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the of_device_get_match_data() helper instead of open coding.
Note that when used with DT, there's always a valid match.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The comment in imx_flush_buffer() states that the state of 4 registers
are to be saved/restored, then only saves and restores 3 registers. The
missing register (UBRC) is read only and thus can't be restored.
Update the comment to reflect reality.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently dw8250_set_termios sets the input clock to the nearest
achievable rate to baudx16. If necessary, the input clock is then
divided down to baudx16 using an integer divider within the UART
device, with the divisor calculated in the 8250 core driver.
However, the clock rate set by dw8250_set_termios and subsequently
divided down could be considerably different to the target baudx16
rate, resulting in incorrect operation. This patch fixes this by
iteratively searching for an input clock rate that is within +/-1.6%
of an integer multiple of the target baudx16 rate.
Signed-off-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a define for the maximum baud rate divisor, to improve code
readability.
Signed-off-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a port has no dma channel defined in the device tree, then
don't attempt to allocate a dma channel for the port.
Also suppress the warning message concerning the failure to allocate
a dma channel. Continue to emit the warning message if a dma
channel is defined but cannot be allocated.
Signed-off-by: Andy Lowe <andy_lowe@mentor.com>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Cedar Fork PCH has similar HSU as has been used on Intel Denverton.
Add PCI ID to get it enumerated.
While here, remove DNV part form INTEL_MID_UART_DNV_FISR to show that is
used not only on Intel Denverton from now on.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
move to arch_initcall to get the console up really early, it is
quite helpful for spotting early boot problems.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The atmel serial port driver reported the following warning on suspend:
atmel_usart f8020000.serial: ttyS1: Unable to drain transmitter
As the ATMEL_US_TXEMPTY status bit in ATMEL_US_CSR is always cleared
when the transmitter is disabled, we need to know the transmitter's
state to return the real fifo state. And as ATMEL_US_CR is write-only,
it is necessary to save the state of the transmitter in a local
variable, and update the variable when TXEN and TXDIS is written in
ATMEL_US_CR.
After those changes, atmel_tx_empty can return "empty" on suspend, the
warning in uart_suspend_port disappears, and suspending is 20ms shorter
for each enabled Atmel serial port.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Tested-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HSCIF has facilities that allow changing the timeout after which an RX
interrupt is triggered even if the FIFO is not filled. This patch allows
changing the default (15 bits of silence) using the existing sysfs
attribute "rx_fifo_timeout".
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the checkpatch.pl error complain:
ERROR: space required before the open brace '{'
Signed-off-by: Gimcuan Hui <gimcuan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is fix the warning reported by smatch as following:
drivers/tty/serial/8250/8250_fintek.c:294 fintek_8250_goto_highspeed()
warn: inconsistent indenting
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The F81216H had 4 clocksource 1.8432/18.432/14.769/24MHzand baud rates can
be up to 1.5Mbits with 24MHz. The register value and mask is the same with
F81866. But F81866 register address is F2h, F81216H is F0h.
We'll implements the dynamic clocksource in fintek_8250_set_termios().
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The F81866 had 4 clocksource 1.8432/18.432/14.769/24MHz and baud rates can
be up to 1.5Mbits with 24MHz. We'll implements the dynamic clocksource in
fintek_8250_set_termios().
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable "dma_is_txing" is an unsigned int, set as either "0" or "1"
in all but one location, where it is instead set to "false". For
consistency, set dma_is_txing to "0" in this location too.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The imx serial driver uses PAGE_SIZE when allocating rx_buf, but then
uses RX_BUF_SIZE (which is currently defined as PAGE_SIZE) to describe
the length of the buffer when initialising the scatter gather list.
In order to ensure that this stays consistent, use RX_BUF_SIZE in both
locations.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Acked-by: Uwe Kleine-König <u.kleine-könig@pengtronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable dma_is_rxing is currently set to 1 in imx_disable_rx_int().
This is problematic as:
- whilst imx_disable_rx_int() is currently always called before
start_rx_dma() this dependency isn't obvious.
- start_rx_dma() does error checking and might exit without
enabling DMA. Currently this will result in dma_is_rxing suggesting
that DMA is being used for recieving.
To avoid these issues, move the setting of dma_is_rxing to
start_rx_dma() when appropriate.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UART core function uart_update_mctrl relies on a cached value of
modem control lines. This was used but not updated by local RTS
control functions within imx.c. These are used for RS485 line
driver enable signalling. Having an out-of-date value in the cached
mctrl can result in the transmitter being enabled when it shouldn't
be.
Fix this by updating the mctrl value before applying it.
Signed-off-by: Ian Jamison <ian.dev@arkver.com>
Origin: id:8195c96e674517b82a6ff7fe914c7ba0f86e702b.1505375165.git.ian.dev@arkver.com
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds support for the rs485 specific properties defined in
Documentation/devicetree/bindings/serial/rs485.txt.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Forwarded: id:20170913081833.2740-7-u.kleine-koenig@pengutronix.de (v5)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The i.MX driver defaulted to full duplex rs485 which is rather
unusual and doesn't match the default implemented in other drivers.
So change the default to half duplex.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We just got a common helper for parsing the rs485 specific
device tree properties. Use it and drop the open coded parser.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We just got a common helper for parsing the rs485 specific
device tree properties. Use it and drop the open coded parser.
As a side effect this adds support for parsing rs485-rts-delay and
rs485-rx-during-tx. As the driver doesn't support this though, probing
fails if these are defined.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We just got a common helper for parsing the rs485 specific
device tree properties. Use it and drop the open coded parser.
Note that there is a small difference between the removed and the now
used implementation: The former cleared flags to 0 if rs485-rts-delay
was given, the common helper clears SER_RS485_RX_DURING_TX and
SER_RS485_ENABLED only but always which makes more sense.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
[ukleinek: point out semantic change in commit log]
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several drivers have the same device tree parsing code. Create
a common helper function for it.
This patch bases on work done by Sascha Hauer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit a6d7514b14 ("tty: serial: lpuart: add a more accurate baud
rate calculation method") the baud rate is now calculated inside the
lpuart32_serial_setbrg() function, so we no longer need to read the
UARTBAUD register inside lpuart32_set_termios().
The 'bd' variable can be simply removed.
This fixes the following build warning with W=1:
drivers/tty/serial/fsl_lpuart.c: In function 'lpuart32_set_termios':
drivers/tty/serial/fsl_lpuart.c:1652:32: warning: variable 'bd' set but not used [-Wunused-but-set-variable]
Fixes: a6d7514b14 ("tty: serial: lpuart: add a more accurate baud rate calculation method")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make this const as it is only stored in the const field 'ops' of an
uart_port structure. It is not referenced in any other file and therefore
make it static too.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This dirver try to implement the Magic SysRq support[1] for
Amlogic Inc's meson platfo
>From the hardware perspective, the UART IP can't detect the 'BREAK' command
clearly via the status register. Instead, we rely on the combination of
'FRAME_ERR bit && ch == 0', and it works fine.
[1] Documentation/admin-guide/sysrq.rst
Signed-off-by: Yixun Lan <dlan@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sccnxp_probe() returns result of regulator_disable() that may lead
to returning zero, while device is not properly initialized.
Also the driver enables clocks, but it does not disable it.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current driver register irq in .startup() and free the irq in
.shutdown(), then user will see the NULL interrupt output from
'cat /proc/interrupts' after the uart port test completed:
...
41: 515 0 0 0 GICv3 257 Level fsl-lpuart
42: 2 0 0 0 GICv3 258 Level
...
It is better to register all the irqs during probe function via devm_request_irq()
to avoid to call free_irq().
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Issue where unprintable characters can occur or output is cut off over
the serial uart / linux console depending on timing.
Problem occurs when changing the serial baud rate when setting up the
new console.The bcm63xx driver does a disable and flush of the uart tx
fifo while there is data still in the tx fifo.
If the tx fifo still has data it is trying to send out, we need to wait
until it is empty before disabling and flushing the uart.
When we now go to change the uart parameters including speed we check
if there is data currently in the tx fifo.If there is was mdelay(10)
and check again.If it tries 3 times and still has data in it we just
continue and sacrifice the tx fifo buffer.
A cleaner and more preferred approach would be to remove :
- spin_lock_irqsave()
- bcm_uart_disable()
- bcm_uart_flush()
However it is not clear if the author put those in to fix another
underlying issue.As a result this solution is a safer approach.
Output before the fix:
[0.306000] 14e00520.serial: ttyS0 at MMIO 0x14e00520 (irq = 9, base_baud = 1687500) is a° 0.315000] console[ttyS0] enabled
Output verified after the fix:
[0.315000] 14e00520.serial: ttyS0 at MMIO 0x14e00520 (irq = 9, base_baud = 1687500) is a bcm63xx_uart [0.334000] console[ttyS0] enabled
Signed-off-by: Russell Enderby <rte@gdn.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
... and __initconst if applicable.
Based on similar work for an older kernel in the Grsecurity patch.
[JD: fix toshiba-wmi build]
[JD: add htcpen]
[JD: move __initconst where checkscript wants it]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Here is the big tty/serial driver update for 4.14-rc1.
Well, not all that big, just a number of small serial driver fixes, and
a new serial driver. Also in here are some much needed goldfish tty
driver (emulator) fixes to try to get that codebase under control.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWa2A+A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylNKACfWOuWb4PEGzPg2hF57V1g0cq8VXEAn0BtZT+n
uuCBV53ylesoHhEhKf/D
=g+za
-----END PGP SIGNATURE-----
Merge tag 'tty-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the big tty/serial driver update for 4.14-rc1.
Well, not all that big, just a number of small serial driver fixes,
and a new serial driver. Also in here are some much needed goldfish
tty driver (emulator) fixes to try to get that codebase under control.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (94 commits)
tty: goldfish: Implement support for kernel 'earlycon' parameter
tty: goldfish: Use streaming DMA for r/w operations on Ranchu platforms
tty: goldfish: Refactor constants to better reflect their nature
serial: 8250_port: Remove useless NULL checks
earlycon: initialise baud field of earlycon device structure
tty: hvcs: make ktermios const
pty: show associative slave of ptmx in fdinfo
tty: n_gsm: Add compat_ioctl
tty: hvcs: constify vio_device_id
tty: hvc_vio: constify vio_device_id
tty: mips_ejtag_fdc: constify mips_cdmm_device_id
Introduce 8250_men_mcb
mcb: introduce mcb_get_resource()
serial: imx: Avoid post-PIO cleanup if TX DMA is started
tty: serial: imx: disable irq after suspend
serial: 8250_uniphier: add suspend/resume support
serial: 8250_uniphier: use CHAR register for canary to detect power-off
serial: 8250_uniphier: fix serial port index in private data
serial: 8250: of: Add new port type for MediaTek BTIF controller on MT7622/23 SoC
dt-bindings: serial: 8250: Add MediaTek BTIF controller bindings
...
After switching to HR timers for RS485 the NULL checks for the object
inside timer functions become useless.
Remove them to avoid confusion to static analyzers.
Fixes 6e0a5de213 ("serial: 8250: Use hrtimers for rs485 delays")
Cc: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For now baud field of earlycon structure device is't initialised at all
in of_setup_earlycon (in oppositе to register_earlycon).
So when I use stdout-path to point earlycon device
(like stdout-path = &serial or stdout-path = "serial:115200n8")
baud field of earlycon device structure remains uninitialised and
earlycon initialization is not performed correctly as
of_setup_earlycon is used.
When pass all arguments via bootargs
(like bootargs = "earlycon=uart8250,mmio32,0xf0005000,115200n8")
initialization is performed correctly as register_earlycon is used.
So initialise baud field of earlycon device structure by value of
"current-speed" property from device tree or from options
(if they exist) when we use of_setup_earlycon
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces the 8250_men_mcb driver for the MEN 16Z125
IP-Core. This is a 16550-type UART with a 60 byte FIFO.
Due to strange old hardware, every board using this IP core requires
different values for uartclk. A reasonable default is included in
addition to the support of three boards. Additional values for other
boards will be added later.
This v2 has some whitespace fixes, I screwed this up yesterday.
Signed-off-by: Michael Moese <michael.moese@men.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The imx_transmit_buffer function should return if TX DMA has already
been started and not just skip over the buffer PIO write loop. (Which
did fix the initial problem, but could have unintentional side-effects)
Tested on an i.MX6Q board with half-duplex RS-485 and with RS-232.
Cc: Clemens Gruber <clemens.gruber@pqgruber.com>
Cc: Uwe-Kleine König <u.kleine-koenig@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Fixes: 514ab34dba ("serial: imx: Prevent TX buffer PIO write when a DMA has been started")
Signed-off-by: Ian Jamison <ian.dev@arkver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If any key on console is pressed when board is suspended,
board hangs.
Driver's interrupt handler must be guaranteed not to run while
resume/suspend_noirq() are being executed. See include/linux/pm.h
for details.
Tested on i.MX6 based board.
The idea of this fix is based on commit in official i.MX kernel tree:
http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git
commit 81e8e7d91d81 ("tty: serial: imx: disable irq after suspend")
Disable rx irq after suspend to avoid interrupt coming in early resume.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Maxim Yu. Osipov <mosipov@ilbers.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add suspend/resume support for UniPhier serial driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250 core uses the SCR as a canary to discover if the console has
been powered-off.
This hardware does not have SCR at offset 7, but an unused register
CHAR at a different offset. As long as the character interrupt is
disabled, the register access has no impact, so it is useful as an
alternative scratch register.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_register_8250_port() may allocate a different port index
than requested. The driver needs to remember the returned value of
serial8250_register_8250_port() for later use. Otherwise, the .remove
hook may unregister a different port.
Fixes: 1a8d2903cb ("serial: 8250_uniphier: add UniPhier serial driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MediaTek BTIF controller is the serial interface similar to UART but it
works only as the digital device which is mainly used to communicate with
the connectivity module called CONNSYS inside the SoC which could be mostly
found on those MediaTek SoCs with Bluetooth feature such as MT7622 and
MT7623 SoCs.
And the controller is made as being compatible with the 8250 register
layout with extra registers such as DMA enablement so it tends to be
integrated with reusing 8250 OF driver. However, DMA mode is not being
supported yet in the current driver.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When moving earlycon early_param handling to serial, the devicetree
earlycons enable condition changed slightly.
We used to only do that for 'console'/'earlycon', but now would also
for 'console='/'earlycon='.
Fix it by using the same condition like before.
Fixes: d503187b6c (of/serial: move earlycon early_param handling to serial)
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These uart_ops structures are only stored in the ops field of a
uart_port structure and this fields is const, so the uart_ops
structures can also be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These uart_ops structures are only stored in the ops field of a
uart_port structure and this fields is const, so the uart_ops
structures can also be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These uart_ops structures are only stored in the ops field of a
uart_port structure and this fields is const, so the uart_ops
structures can also be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These uart_ops structures are only stored in the ops field of a
uart_port structure and this fields is const, so the uart_ops
structures can also be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These uart_ops structures are only stored in the ops field of a
uart_port structure and this fields is const, so the uart_ops
structures can also be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These uart_ops structures are only stored in the ops field of a
uart_port structure and this fields is const, so the uart_ops
structures can also be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These uart_ops structures are only stored in the ops field of a
uart_port structure and this fields is const, so the uart_ops
structures can also be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These uart_ops structures are only stored in the ops field of a
uart_port structure and this fields is const, so the uart_ops
structures can also be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These uart_ops structures are only stored in the ops field of a
uart_port structure and this fields is const, so the uart_ops
structures can also be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
parisc_device_id are not supposed to change at runtime. All functions
working with parisc_device_id provided by <asm/parisc-device.h> work
with const parisc_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
parisc_device_id are not supposed to change at runtime. All functions
working with parisc_device_id provided by <asm/parisc-device.h> work
with const parisc_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
66AK2G UART instances are not apart of the ALWAYS_ON power domain.
Therefore, pm_runtime calls must be made to properly insure the appropriate
power domains needed by UART are on. Keep legacy clk api calls since other
users of this driver may not support PM runtime.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use slightly more compact of_property_read_bool() calls for the boolean
properties instead of of_find_property() calls.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously the timers where based on the classic timers, giving a too
coarse resolution on systems with configs of less than 1000 HZ.
This patch changes the rs485 timers to hrtimers.
Signed-off-by: Rafael Gago Castano <rgc@hms.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously the rs485 settings weren't considered when setting the RTS
line, so e.g. closing and reopening a port made serial_core to drive
the line as if rs485 was disabled.
This patch fixes those issues.
Signed-off-by: Rafael Gago Castano <rgc@hms.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use more compact of_property_read_bool() call for a boolean property
instead of of_find_property() call in sci_parse_dt().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It used to be a gap in port definitions after PORT_MAX_8250. Since the
new drivers are coming the gap become shorter and shorter until the
commit a2d6a987bf ("serial: 8250: Add new port type for TI DA8xx/66AK2x")
completely removed it.
So, while type here is just a formality, make things a little bit more
explicit for this driver and move port types to UAPI header. Note,
it uses two types for now.
Fixes: fddceb8b53 ("tty: 8250: Add 64byte UART support for FSL platforms")
Cc: Priyanka Jain <Priyanka.Jain@freescale.com>
Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to duplicate a flag which IRQ core takes care of.
Replace custom flag by IRQ core API that retrieves its state.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to duplicate a flag which IRQ core takes care of.
Replace custom flag by IRQ core API that retrieves its state.
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to duplicate a flag which IRQ core takes care of.
Replace custom flag by IRQ core API that retrieves its state.
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to duplicate a flag which IRQ core takes care of.
Replace custom flag by IRQ core API that retrieves its state.
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the request_irq() call to the end of the msm_startup(),
so that we don't handle interrupts while msm_startup() is
running. This avoids potential races while initialization
is in progress. For example, consider below scenario
where rx handler reads the intermediate value of dma->chan,
set in msm_request_rx_dma(), and tries to do dma mapping,
which results in data abort.
uart_port_startup()
msm_startup()
request_irq()
...
msm_request_rx_dma()
...
dma->chan = dma_request_slave_channel_reason(dev, "rx");
<UART RX IRQ>
msm_uart_irq()
msm_handle_rx_dm()
msm_start_rx_dma()
dma->desc = dma_map_single()
<data abort>
Signed-off-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Reviewd-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to do a NULL check for debugfs_remove().
Quoting Documentation/filesystems/debugfs.txt:
"The dentry value can be NULL, in which case nothing will be removed."
, so remove the unneeded NULL check.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_get_irq() returns an error code, but the sprd_serial driver
ignores it and always returns -ENODEV. This is not correct and,
prevents -EPROBE_DEFER from being propagated properly.
Also, notice that platform_get_irq() no longer returns 0 on error:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e330b9a6bb35dc7097a4f02cb1ae7b6f96df92af
Print and propagate the return value of platform_get_irq on failure.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These uart_ops structures are only stored in the ops field of a
uart_port structure and this fields is const, so the uart_ops
structures can also be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These uart_ops structures are only stored in the ops field of a
uart_port structure and this fields is const, so the uart_ops
structures can also be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These vendor_data structures are only stored in the vendor field of
the uart_amba_port structure, as defined in the same file, and this
field is declared as const. Thus the vendor_data structures can be
const too.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are two tty serial driver fixes for 4.13-rc5. One is a revert of a
-rc1 patch that turned out to not be a good idea, and the other is a fix
for the pl011 serial driver.
Both have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWY+1vw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykreACeLI2spfagnOcnW264PGHxLMgj47EAn0JPSNIg
5FLEtVsgxMuc8kc4LkDb
=58g+
-----END PGP SIGNATURE-----
Merge tag 'tty-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are two tty serial driver fixes for 4.13-rc5. One is a revert of
a -rc1 patch that turned out to not be a good idea, and the other is a
fix for the pl011 serial driver.
Both have been in linux-next with no reported issues"
* tag 'tty-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "serial: Delete dead code for CIR serial ports"
tty: pl011: fix initialization order of QDF2400 E44
This reverts commit 1104321a7b.
The code is not dead at all and breaks winbond-cir.
Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
00:02: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
00:03: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a CIR port
lirc lirc0: lirc_dev: driver ir-lirc-codec (winbond-cir) registered at minor = 0
winbond-cir 00:03: Region 0x2f8-0x2ff already in use!
winbond-cir: probe of 00:03 failed with error -16
Signed-off-by: Sean Young <sean@mess.org>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device-specific property should be prefixed with the vendor name,
not "linux,", as Linus Walleij pointed out. Change this and document the
bindings of this platform device.
We didn't ship the old binding in a release yet. So we can still change
it without breaking an official API.
Fixes: 380b1e2f3a ("gpio-exar/8250-exar: Make set of exported GPIOs configurable")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The work-around for Qualcomm Technologies QDF2400 Erratum 44 hinges on a
global variable defined in the pl011 driver. The ACPI SPCR parsing code
determines whether the work-around is needed, and if so, it changes the
console name from "pl011" to "qdf2400_e44". The expectation is that
the pl011 driver will implement the work-around when it sees the console
name. The global variable qdf2400_e44_present is set when that happens.
The problem is that work-around needs to be enabled when the pl011
driver probes, not when the console name is queried. However, sbsa_probe()
is called before pl011_console_match(). The work-around appeared to work
previously because the default console on QDF2400 platforms was always
ttyAMA1. The first time sbsa_probe() is called (for ttyAMA0),
qdf2400_e44_present is still false. Then pl011_console_match() is called,
and it sets qdf2400_e44_present to true. All subsequent calls to
sbsa_probe() enable the work-around.
The solution is to move the global variable into spcr.c and let the
pl011 driver query it during probe time. This works because all QDF2400
platforms require SPCR, so parse_spcr() will always be called.
pl011_console_match still checks for the "qdf2400_e44" console name,
but it doesn't do anything else special.
Fixes: 5a0722b898 ("tty: pl011: use "qdf2400_e44" as the earlycon name for QDF2400 E44")
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The struct serial_rs485 parameter is both input and output and is
supposed to hold the actually used configuration on return. So clear
unsupported settings.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the board we are guessing has been listed in black list we don't need
to enable it twice. The associated driver, if any, will take care about
proper initialization.
To achieve this we split out two helper functions, i.e.
serial_pci_is_class_communication() and serial_pci_is_blacklisted() which will
be called before pcim_enable_device(). We can do this since PCI specification
requires class, device and vendor ID registers to be always present in the
configuration space.
As an example what happens before this patch applied
(These are some debug prints, don't search for them in kernel sources):
serial 0000:00:04.1: Mapped GSI28 to IRQ28
serial 0000:00:04.2: Mapped GSI29 to IRQ29
serial 0000:00:04.3: Mapped GSI54 to IRQ54
8250_mid 0000:00:04.1: Mapped GSI28 to IRQ28
8250_mid 0000:00:04.2: Mapped GSI29 to IRQ29
8250_mid 0000:00:04.3: Mapped GSI54 to IRQ54
After we will have just last three lines out of above.
8250_mid 0000:00:04.1: Mapped GSI28 to IRQ28
8250_mid 0000:00:04.2: Mapped GSI29 to IRQ29
8250_mid 0000:00:04.3: Mapped GSI54 to IRQ54
While here, correct a value of error code mentioned in the comment of
serial_pci_guess_board().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
First 16 bits in the flags field are user-visible except
UPF_NO_TXEN_TEST. To keep it clean we introduce internal quirks and move
UPF_NO_TXEN_TEST to them. Rename the constant to UPQ_NO_TXEN_TEST to
distinguish with port flags. Users are converted accordingly.
The quirks field might be extended later to hold the additional ones.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
upf_t is a bitwise defined type and any assignment from different, but
compatible, types makes static analyzer unhappy.
drivers/tty/serial/serial_core.c:793:29: warning: incorrect type in assignment (different base types)
drivers/tty/serial/serial_core.c:793:29: expected int [signed] flags
drivers/tty/serial/serial_core.c:793:29: got restricted upf_t [usertype] flags
drivers/tty/serial/serial_core.c:867:19: warning: incorrect type in assignment (different base types)
drivers/tty/serial/serial_core.c:867:19: expected restricted upf_t [usertype] new_flags
drivers/tty/serial/serial_core.c:867:19: got int [signed] flags
Enforce corresponding types when upf_t being assigned.
Note, we need __force attribute due to the scope of variable. It's being
used in user space with plain old type while kernel uses bitwise one.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The earlycon would be alive outside the init code in these cases:
1/ we have keep_bootcon in cmdline.
2/ we don't have a real console to switch to.
So remove the __init marking to avoid invalid memory access.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The earlycon would be alive outside the init code in these cases:
1/ we have keep_bootcon in cmdline.
2/ we don't have a real console to switch to.
So remove the __init marking to avoid invalid memory access.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The earlycon would be alive outside the init code in these cases:
1/ we have keep_bootcon in cmdline.
2/ we don't have a real console to switch to.
So remove the __init marking to avoid invalid memory access.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The earlycon would be alive outside the init code in these cases:
1/ we have keep_bootcon in cmdline.
2/ we don't have a real console to switch to.
So remove the __init marking to avoid invalid memory access.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The earlycon would be alive outside the init code in these cases:
1/ we have keep_bootcon in cmdline.
2/ we don't have a real console to switch to.
So remove the __init marking to avoid invalid memory access.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are several error handling paths in aspeed_vuart_probe(),
where sysfs group is left unremoved. The patch fixes them.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Spreadtrum's serial device, nearly all of interrupts would be cleared
by hardware except timeout interrupt. This patch removed the operation
of clearing all interrupt in irq handler, instead added an if statement
to check if the timeout interrupt is supposed to be cleared.
Wrongly clearing timeout interrupt would lead to uart data stay in rx
fifo, that means the driver cannot read them out anymore.
Signed-off-by: Lanqing Liu <lanqing.liu@spreadtrum.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The wait queue was only initialized and then checked if it contains
active jobs but a job is never added. The last real user was removed
with commit 9d297239b8 ("serial: imx-serial - update UART IMX driver
to use cyclic DMA").
Further there is no need to release the lock for the check if the port
should be woken up, (and IMHO there never was) so drop the unlock/lock
pair in dma_tx_callback(), too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
clk_disable_unprepare(info->clk) is missed in of_platform_serial_probe(),
while irq_dispose_mapping(port->irq) is missed in of_platform_serial_setup().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-serial@vger.kernel.org
Cc: sparclinux@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
2442 1088 8 3538 dd2 tty/serial/jsm/jsm_driver.o
File size After adding 'const':
text data bss dec hex filename
3082 448 8 3538 dd2 tty/serial/jsm/jsm_driver.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
12626 18128 0 30754 7822 tty/serial/8250/8250_pci.o
File size After adding 'const':
text data bss dec hex filename
23986 6768 0 30754 7822 tty/serial/8250/8250_pci.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
4030 1280 0 5310 14be tty/serial/8250/8250_exar.o
File size After adding 'const':
text data bss dec hex filename
4958 352 0 5310 14be tty/serial/8250/8250_exar.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds fifo mode support for rx and tx.
A fifo configuration is set in each port structure.
Add has_fifo flag to usart configuration to use fifo only when possible.
Signed-off-by: Gerald Baeza <gerald.baeza@st.com>
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for wake-up from low power modes. This extends stm32f7.
Introduce new compatible for stm32h7 to manage wake-up capability.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement support of RTS in USART control register
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Increase max number of ports for stm32h7
which supports up to 8 uart and usart instances.
Signed-off-by: Gerald Baeza <gerald.baeza@st.com>
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Correct management of multi-ports. Each port has
its own last residue value and its own alias.
Signed-off-by: Gerald Baeza <gerald.baeza@st.com>
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This mirrors commit 2a41bc2a2b but for 32-bit register definitions.
Fix a minor typo while at it.
Signed-off-by: Marius Vlad <marius.vlad0@gmail.com>
CC: Nicolae Rosia <nicolae_rosia@mentor.com>
CC: Stefan Golinschi <stefan.golinschi@gmail.com>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement serial console driver to complement earlycon.
Based on LeMaker linux-actions tree.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 0d6fce9044 ("tty: serial: lpuart: introduce lpuart_soc_data to
represent SoC property") introduced a buggy logic for detecting the 32-bit
type UART since the condition: "if (sport->port.iotype & UPIO_MEM32BE)"
is always true.
Performing such bitfield AND operation is not correct, because in the
case of Vybrid UART iotype is UPIO_MEM (2), so:
UPIO_MEM & UPIO_MEM32BE = 010 & 110 = 010, which is true.
Such logic tells the driver to always treat the UART operations as 32-bit,
leading to the driver misbehavior on Vybrid.
Fix the 32-bit type detection logic to avoid UART breakage on Vybrid.
While at it, introduce a lpuart_is_32() function to help readability.
Fixes: 0d6fce9044 ("tty: serial: lpuart: introduce lpuart_soc_data to represent SoC property")
Reported-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function imx_transmit_buffer starts a TX DMA if DMA is enabled, since
commit 91a1a909f9 ("serial: imx: Support sw flow control in DMA mode").
It also carries on and attempts to write the same TX buffer using PIO.
This results in TX data corruption and double-incrementing xmit->tail
with the knock-on effect of tail passing head and a page of garbage
being sent out.
This seems to be triggered mostly when using RS485 half duplex on SMP
systems, but is probably not limited to just those.
Tested locally on an i.MX6Q with an RS485 half duplex transceiver on
UART3, and also by Clemens Gruber.
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Ian Jamison <ian.dev@arkver.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit a3015affdf as there
are complaints that it is incorrect.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Nandor Han <nandor.han@ge.com>
Cc: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org
The kstrtol() function returns -ERANGE as well as -EINVAL so these tests
are not enough. It's not a super serious bug, but my static checker
correctly complains that the "r" variable might be used uninitialized.
Fixes: 5d23188a47 ("serial: sh-sci: make RX FIFO parameters tunable via sysfs")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It looks like we intended to return an error code here, because we
dereference "ascport->pinctrl" on the next lines.
Fixes: 6929cb00a5 ("serial: st-asc: Read in all Pinctrl states")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the code like the rest of the kernel.
Link: http://lkml.kernel.org/r/55d3e89d50bb03d603bfb28019fab07f48bdc714.1499284835.git.joe@perches.com
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Pat Gefre <pfg@sgi.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Core:
- Export add/remove for lookup tables so that modules can export GPIO
descriptor tables.
- Handle GPIO sleep states: it is now possible to flag that a GPIO line
may loose its state during suspend/resume of the system to save
power. This is used in the Wolfson Micro Arizona driver.
- ACPI-based GPIO was tightened up a lot around the edges.
- Use bitmap_fill() to speed up a loop.
New drivers:
- Exar XRA1403 SPI-based GPIO.
- MVEBU driver now supports Armada 7K and 8K.
- LP87565 PMIC GPIO.
- Renesas R-CAR R8A7743 (RZ/G1M).
- The new IOT2040 8250 serial/GPIO also comes in through this
changeset.
Substantial driver changes:
- Seriously fix the Exar 8250 GPIO portions to work.
- The MCP23S08 was moved out to a pin control driver.
- Convert MEVEBU to use regmap for register access.
- Drop Vulcan support from the Broadcom driver.
- Serious cleanup and improvement of the mockup driver, giving us a
better test coverage.
Misc:
- Lots of janitorial clean up.
- A bunch of documentation fixes.
-----BEGIN PGP SIGNATURE-----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=TpW1
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.13 series.
Some administrativa:
I have a slew of 8250 serial patches and the new IOT2040 serial+GPIO
driver coming in through this tree, along with a whole bunch of Exar
8250 fixes. These are ACKed by Greg and also hit drivers/platform/*
where they are ACKed by Andy Shevchenko.
Speaking about drivers/platform/* there is also a bunch of ACPI stuff
coming through that route, again ACKed by Andy.
The MCP23S08 changes are coming in here as well. You already have the
commits in your tree, so this is just a result of sharing an immutable
branch between pin control and GPIO.
Core:
- Export add/remove for lookup tables so that modules can export GPIO
descriptor tables.
- Handle GPIO sleep states: it is now possible to flag that a GPIO
line may loose its state during suspend/resume of the system to
save power. This is used in the Wolfson Micro Arizona driver.
- ACPI-based GPIO was tightened up a lot around the edges.
- Use bitmap_fill() to speed up a loop.
New drivers:
- Exar XRA1403 SPI-based GPIO.
- MVEBU driver now supports Armada 7K and 8K.
- LP87565 PMIC GPIO.
- Renesas R-CAR R8A7743 (RZ/G1M).
- The new IOT2040 8250 serial/GPIO also comes in through this
changeset.
Substantial driver changes:
- Seriously fix the Exar 8250 GPIO portions to work.
- The MCP23S08 was moved out to a pin control driver.
- Convert MEVEBU to use regmap for register access.
- Drop Vulcan support from the Broadcom driver.
- Serious cleanup and improvement of the mockup driver, giving us a
better test coverage.
Misc:
- Lots of janitorial clean up.
- A bunch of documentation fixes"
* tag 'gpio-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (70 commits)
serial: exar: Add support for IOT2040 device
gpio-exar/8250-exar: Make set of exported GPIOs configurable
platform: Accept const properties
serial: exar: Factor out platform hooks
gpio-exar/8250-exar: Rearrange gpiochip parenthood
gpio: exar: Fix iomap request
gpio-exar/8250-exar: Do not even instantiate a GPIO device for Commtech cards
serial: uapi: Add support for bus termination
gpio: rcar: Add R8A7743 (RZ/G1M) support
gpio: gpio-wcove: Fix GPIO control register offset calculation
gpio: lp87565: Add support for GPIO
gpio: dwapb: fix missing first irq for edgeboth irq type
MAINTAINERS: Take maintainership for GPIO ACPI support
gpio: exar: Fix reading of directions and values
gpio: exar: Allocate resources on behalf of the platform device
gpio-exar/8250-exar: Fix passing in of parent PCI device
gpio: mockup: use devm_kcalloc() where applicable
gpio: mockup: add myself as author
gpio: mockup: improve the error message
gpio: mockup: don't return magic numbers from probe()
...
This implements the setup of RS232 and the switch-over to RS485 or RS422
for the Siemens IOT2040. That uses an EXAR XR17V352 with external logic
to switch between the different modes. The external logic is controlled
via MPIO pins of the EXAR controller.
Only pin 10 can be exported as GPIO on the IOT2040. It is connected to
an LED.
As the XR17V352 used on the IOT2040 is not equipped with an external
EEPROM, it cannot present itself as IOT2040-variant via subvendor/
subdevice IDs. Thus, we have to check via DMI for the target platform.
Co-developed with Sascha Weisenberger.
Signed-off-by: Sascha Weisenberger <sascha.weisenberger@siemens.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On the SIMATIC, IOT2040 only a single pin is exportable as GPIO, the
rest is required to operate the UART. To allow modeling this case,
expand the platform device data structure to specify a (consecutive) pin
subset for exporting by the gpio-exar driver.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
This prepares the addition of IOT2040 platform support by preparing the
needed setup and rs485_config hooks.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the parent of the exar gpiochip to its platform device, like other
gpiochips are doing it. In order to keep the relationship discoverable
for ACPI systems, set the platform device companion to the PCI device.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Commtech adapters need the MPIOs for internal purposes, and the
gpio-exar driver already refused to pick them up. But there is actually
no point in even creating the underlying platform device.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On new LPUART versions, the oversampling ratio for the receiver can be
changed from 4x (00011) to 32x (11111) which could help us get a more
accurate baud rate divider.
The idea is to use the best OSR (over-sampling rate) possible.
Note, OSR is typically hard-set to 16 in other LPUART instantiations.
Loop to find the best OSR value possible, one that generates minimum
baud diff iterate through the rest of the supported values of OSR.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Mingkai Hu <Mingkai.Hu@nxp.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
earlycon is executed quite early before the device tree probe,
so we need correctly initialize the port membase and iotype for
imx7ulp during early console setup before using.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Mingkai Hu <Mingkai.Hu@nxp.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The lpuart of imx7ulp is basically the same as ls1021a. It's also
32 bit width register, but unlike ls1021a, it's little endian.
Besides that, imx7ulp lpuart has a minor different register layout
from ls1021a that it has four extra registers (verid, param, global,
pincfg) located at the beginning of register map, which are currently
not used by the driver and less to be used later.
To ease the register difference handling, we add a reg_off member
in lpuart_soc_data structure to represent if the normal
lpuart32_{read|write} requires plus a offset to hide the issue.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Mingkai Hu <Mingkai.Hu@nxp.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Cc: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use standard port->iotype to distinguish endian difference. Note as we
read/write register by checking iotype dynamically, we need to initialize
the iotype correctly for earlycon as well to avoid a break.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com> (supporter:TTY LAYER)
Cc: Stefan Agner <stefan@agner.ch>
Cc: Mingkai Hu <Mingkai.Hu@nxp.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Cc: Fugang Duan <fugang.duan@nxp.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
ChangeLog:
v3->v4:
* Removed unneeded semicolon catched by 0day Robot.
v2->v3:
* Instead of using global var, use standard port->iotype to distinguish
endian difference.
v1->v2:
* No changes
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to the original lpuart32_read/write takes no port specific
information arguments, it's hard to distinguish port difference
within the API. Although it works before, but not suitable anymore
when adding more new chips support.
So let's convert it to accept a new struct uart_port argument
to make it be able to retrieve more port specific information.
This is a preparation for the later adding new chips support
more easily. No functions changes.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Mingkai Hu <Mingkai.Hu@nxp.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Cc: Fugang Duan <fugang.duan@nxp.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is used to dynamically check the SoC specific lpuart properies.
Currently only the iotype is added, it functions the same as before.
With this, new chips with different iotype will be more easily added.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Mingkai Hu <Mingkai.Hu@nxp.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Cc: Fugang Duan <fugang.duan@nxp.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The size of the DMA buffer can affect the delta time between data being
produced and data being consumed. Basically the DMA system will move
data to tty buffer when a) DMA buffer is full b) serial line is idle.
The situation is visible when producer generates data continuously and
there is no possibility for idle line. At this point the DMA buffer is
directly affecting the delta time.
The patch will add the possibility to configure the DMA buffers in DT,
which case by case can be configured separately for every driver
instance. The DT configuration is optional and in case missing the
driver will use the 4096 buffer with 4 periods (as before), therefore no
clients are impacted by this change.
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
