Add missing clock branch to enable onboard storage
for msm899(2/4).
Signed-off-by: Jeremy McNicoll <jeremymc@redhat.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Once a gdsc is brought in and out of HW control, there is a
power down and up cycle which can take upto 1us. Polling on
the gdsc status immediately after the hw control enable/disable
can mislead software/firmware to belive the gdsc is already either on
or off, while its yet to complete the power cycle.
To avoid this add a 1us delay post a enable/disable of HW control
mode.
Also after the HW control mode is disabled, poll on the status to
check gdsc status reflects its 'on' before force disabling it
in software.
Reported-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Tested-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Fixes: 904bb4f5c7 ("clk: qcom: gdsc: Add support for gdscs with HW control")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add definition of EBI2 clock used by MDM9615 NAND controller.
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-soc@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Zoran Markovic <zmarkovic@sierrawireless.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
[sboyd@codeaurora.org: ebi2_clk halt bit is 24 not 23]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add support to use reset control framework for resetting MSS
with hexagon v56 1.5.0.
Signed-off-by: Avaneesh Kumar Dwivedi <akdwived@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The current driver code gives the crash or gets hang while switching
the CPU frequency some time. The APSS CPU Clock divider is not glitch
free so it the APPS clock need to be switched for stable clock during
the change.
This patch adds the frequency change notifier for APSS CPU clock. It
changes the parent of this clock to stable PLL FEPLL500 for
PRE_RATE_CHANGE event. This event will be generated before actual
clock set operations. The clock set operation will again change its
corresponding parent by getting the same from frequency table.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
[sboyd@codeaurora.org: Indent less in probe]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This adds all RPM based clocks for msm8974, except cxo and
gfx3d_clk_src.
Tested-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The APSS CPU clock does not contain all the frequencies in its
frequency table so this patch adds the same.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
1. The parent for sdcc clock is sdccpll.
2. The frequency value was wrong so modified the same.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The current ipq4019 clock driver does not have the node for
PCNOC so this patch adds and registers the PCNOC clock nodes.
This PCNOC clock is critical and should not be turned off so
setting CRITICAL flag also.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The current ipq4019 clock driver does not have support for all
the frequency supported by APSS CPU. APSS CPU frequency is
provided with APSS CPU PLL divider which divides down the VCO
frequency. This divider is nonlinear and specific to IPQ4019
so the standard divider code cannot be used for this.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The current ipq4019 clock driver registered the PLL clocks and
dividers as fixed clock. These fixed clock needs to be removed
from driver probe function and same need to be registered with
clock framework. These PLL clocks should be programmed only
once and the same are being programmed already by the boot
loader so the set rate operation is not required for these
clocks. Only the rate can be calculated by clock operations
in clock driver file so this patch adds the same.
The PLL takes the reference clock from XO and generates the
intermediate VCO frequency. This VCO frequency will be divided
down by different PLL internal dividers. Some of the PLL
internal dividers are fixed while other are programmable.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The venus video ip's internal core blocks are under the
control of the firmware and their powerdomains needs to be
'ON' only when used by the firmware. So putting it into
hw controlled mode lets this to happen, otherwise the firmware
hangs checking for this.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some GDSCs might support a HW control mode, where in the power
domain (gdsc) is brought in and out of low power state (while
unsued) without any SW assistance, saving power.
Such GDSCs can be configured in a HW control mode when powered on
until they are explicitly requested to be powered off by software.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Fix the clk_hw references to the actual clocks and add a xlate function
to return the hw pointers from the already existing static array.
Reported-by: Michael Scott <michael.scott@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Fix the clk_hw references to the actual clocks and add a xlate function
to return the hw pointers from the already existing static array.
Reported-by: Michael Scott <michael.scott@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The sdcc driver for msm8996/msm8916/msm8974/msm8994 and apq8084
expects a clk_set_rate() on the sdcc rcg clk to set
a floor value of supported clk rate closest to the requested
rate, by looking up the frequency table.
So move all the sdcc rcgs on all these platforms to use the
newly introduced clk_rcg2_floor_ops
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Jeremy McNicoll <jeremymc@redhat.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The default behaviour with clk_rcg2_ops is for the
clk_round_rate()/clk_set_rate() to return/set a ceil clock
rate closest to the requested rate by looking up the corresponding
frequency table.
However, we do have some instances (mainly sdcc on various platforms)
of clients expecting a clk_set_rate() to set a floor value instead.
Add a new clk_rcg2_floor_ops to handle this for such specific
rcg instances
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This adds initial support for clocks controlled by the Resource
Power Manager (RPM) processor on some Qualcomm SoCs, which use
the qcom_rpm driver to communicate with RPM.
Such platforms are apq8064 and msm8960.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This adds initial support for clocks controlled by the Resource
Power Manager (RPM) processor on some Qualcomm SoCs, which use
the qcom_smd_rpm driver to communicate with RPM.
Such platforms are msm8916, apq8084 and msm8974.
The RPM is a dedicated hardware engine for managing the shared
SoC resources in order to keep the lowest power profile. It
communicates with other hardware subsystems via shared memory
and accepts clock requests, aggregates the requests and turns
the clocks on/off or scales them on demand.
This driver is based on the codeaurora.org driver:
https://www.codeaurora.org/cgit/quic/la/kernel/msm-3.10/tree/drivers/clk/qcom/clock-rpm.c
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
[sboyd@codeaurora.org: Remove useless braces for single line if]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Currently the RPM/RPM-SMD clock drivers do not register the xo clocks,
so we should always add factor clock. When we later add xo clocks support
into the drivers, we should update this function to skip registration.
By doing so we avoid any DT dependencies.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The clock definition was ported from the Google 3.10 kernel tree to
work with the latest kernel.
Signed-off-by: Bastian Köcher <mail@kchr.de>
[jeremymc@redhat.com: created new commit of just dt-bindings]
Signed-off-by: Jeremy McNicoll <jeremymc@redhat.com>
[sboyd@codeaurora.org: Tidy up commit text and Kconfig help]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The clocks on these boards run at 25 MHz, not 19.2 and 27 like
other platforms. Unfortunately I copy/pasted from other similar
SoCs but forgot this one is different. Fix it.
Fixes: a085f877a8 ("clk: qcom: Move cxo/pxo/xo into dt files")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add frequency tables for a few RCG clocks in msm8996
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This would be useful in subsequent patches when the .set_rate operation
would need to identify if the PLL is actually enabled
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
[sboyd@codeaurora.org: Simplify return statement of is_enabled op]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The votable alpha PLLs need to have the fsm mode enabled as part
of the initialization. The sequence seems to be the same as used
by clk-pll, so move the function which does this into a common
place and reuse it for the clk-alpha-pll
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some alpha PLLs have support for only a 16bit programable Alpha Value
(as against the default 40bits). Add a flag to handle the 16bit alpha
registers
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add a function to do initial configuration of the alpha plls
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some PLLs can support an HW FSM mode (different from the Votable FSMs,
though its the same bit used to enable Votable FSMs as well as HW FSMs)
which enables the HW to do the bypass/reset/enable-output-ctrl sequence
on its own. So all thats needed from SW is to set the FSM_ENA bit.
PLL_ACTIVE_FLAG is whats used to check if the PLL is active/enabled.
Some of the PLLs which support HW FSM can also need an OFFLINE request
that needs to be toggled across the enable/disable. We use a flag to
identify such cases and handle them.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The current I2C freq table uses MND values which is not
applicable for I2C since its RCG does not have MND
counter. This patch updates the freq table for 19.05
MHz clk frequency with FEPLL_200 parent.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Drop the assignment of regmap_read return code to val, so the code checks
the value read.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add a flag to mark gdscs which need to support the clamp deassert/assert
before and after the gdsc enable/disable
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch corrects the register offset for pcie2 pipe clock.
Offset according to datasheet is 0x6e018 instead of 0x6e108.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: b1e010c073 ("clk: qcom: Add MSM8996 Global Clock Control (GCC) driver")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch selects QCOM_GDSC Kconfig for msm8996 GCC and MMCC clock
controllers, as these provide some of the gdscs on the SOC.
Also selecting this config will make it align with other drivers which
do the same.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: 52111672f7 ("clk: qcom: gdsc: Add GDSCs in msm8996 GCC")
Fixes: 7e824d5079 ("clk: qcom: gdsc: Add mmcc gdscs for msm8996 family")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that we have clk_hw based provider APIs to register clks, we
can get rid of struct clk pointers in this driver, allowing us to
move closer to a clear split of consumer and provider clk APIs.
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add BIMC gdsc data found in MMCC part of msm8996 family of devices.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The field "owner" is set by the core.
Thus delete an unneeded initialisation.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
In order to support the Qualcomm MDM9615 SoC, add support for
the Global and LPASS Clock Controllers.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This adds the EBI2 2X and EBI2 clocks to the MSM8660/APQ8060
GCC. This is necessary to enable clocking of the external bus
interface so that peripherals on it can be mounted. These two
clocks are simple gated branch clocks.
In the vendor tree clock-8x60, these clocks have some kind of
dependency, the EBI2 clock has .depends = &ebi2_2x_clk.c,
what this means is undocumented, it doesn't seem like there
is a parent/child relationship, so the solution I chose was to
just have the EBI2 driver get and enable both clocks.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This clk is critical to operation of the SoC and should never be
turned off. Furthermore, there are no consumers of this clk so
let's just delete it so things like eMMC work.
Reported-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: b1e010c073 ("clk: qcom: Add MSM8996 Global Clock Control (GCC) driver")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The branch clocks MMSS_MMAGIC_AXI_CLK and MMAGIC_BIMC_AXI_CLK are
controlled by RPM when the APPs processor enable or disable the
RPM_MMAXI_CLK.
During the boot sequence, someone can enable the RPM_MMAXI_CLK, resulting
in register status bits showing that these clocks are enabled, our
clock driver may look at the enabled status of these clocks and try to
disable them since it thinks they are unused.
Don't make the clock driver touch these clocks.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds the CLK_SET_RATE_PARENT flag for the crypto core and
ahb blocks. Without this flag, clk_set_rate can fail for certain
frequency requests.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Fixes: 3966fab8b6 ("clk: qcom: Add MSM8916 Global Clock Controller support")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Drivers for these don't exist yet so we will add them as fixed clocks
so we don't BUG() if we change clocks that reference these clocks.
Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
When this was added not all the remaining defines were switched over to
use enums, so let's complete that process here
Reported-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The qcom_reset_ops structure is never modified. Make it const.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The offset seems to have been copied from the sata clk. Fix it so
that enabling the crypto engine source clk works.
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: 5f775498bd ("clk: qcom: Fully support apq8064 global clock control")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The clk_rcg_pixel_set_rate clk_op sets up the pre-divider by reading
its current value from the NS register.
Using the pre-divider wasn't really intended when creating these ops.
The pixel RCG was only intended to achieve fractional multiplication
provided in the pixel_table array. Leaving the pre-divider to the
existing register value results in a wrong pixel clock when the
bootloader sets up the display. This was left unidentified because
the IFC6410 Plus board on which this was verified didn't have a
bootloader that configured the display.
Don't set the RCG pre-divider in freq_tbl to the existing NS register
value. Force it to 1 and only use the M/N counter to achieve the desired
fractional multiplication.
Cc: Vinay Simha <vinaysimha@inforcecomputing.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds support for the global clock controller found on
the IPQ4019 based devices. This includes UART, I2C, SPI etc.
Signed-off-by: Pradeep Banavathi <pradeepb@codeaurora.org>
Signed-off-by: Senthilkumar N L <snlakshm@codeaurora.org>
Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
[sboyd@codeaurora.org: Drop 0x16024 enable_reg in crypto_ahb]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch corrects the enable register offset which is actually 0x36cc
instead of 0x36c4
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: 5f775498bd ("clk: qcom: Fully support apq8064 global clock control")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This reverts commit 329cabcecf.
The commit that caused us to specify LE device endianness here,
29bb45f25f (regmap-mmio: Use native endianness for read/write,
2015-10-29), has been reverted in mainline so now when we specify
LE it actively breaks big endian kernels because the byte
swapping in regmap-mmio is incorrect. Let's revert this change
because it will 1) fix the big endian kernels and 2) be redundant
to specify LE because that will become the default soon.
Cc: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
With gdsc driver capable of handling hierarchical power domains,
specify oxili_gdsc as parent of oxilicx_gdsc.
Remove all direct calls to genpd from the mmcc clock driver. The
adding and removing of subdomains is now handled from within
the gdsc driver.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add all gdsc data which are part of mmcc on msm8996 family
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add all data for the GDSCs which are part of msm8996 GCC block
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some gdscs might be controlled via voting registers and might not
really disable when the kernel intends to disable them (due to other
votes keeping them enabled)
Mark these gdscs with a flag for we do not check/wait on a disable
status for these gdscs within the kernel disable callback.
Also at boot, if these GDSCs are found to be ON, we make sure we
vote for them before we inform the genpd framework about their
status. If genpd gets no users, it then disables (removes the vote)
them as part of genpd_poweroff_unused()
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some gdsc power domains can have a gds_hw_controller block inside
to help ensure all slave devices within the power domain are idle
before the gdsc is actually switched off.
This is mainly useful in power domains which host a MMU, in which
case its necessary to make sure there are no outstanding MMU operations
or pending bus transactions before the power domain is turned off.
In gdscs with gds_hw_controller block, its necessary to check the
gds_hw_ctrl status bits instead of the ones in gdscr, to determine
the state of the powerdomain.
While at it, also move away from using jiffies and use ktime APIs
instead for busy looping on status bits.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some qcom SoCs' can have hierarchical power domains. Let the gdsc structs
specify the parents (if any) and the driver add genpd subdomains for them.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We were not checking the return from devm_add_action() which can fail.
Start using the helper and devm_add_action_or_reset() and return
directly as we know that the cleanup has been done by this helper.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This clock is required for loading the qdsp firmware.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add a driver for the multimedia clock controller found on MSM8996
based devices. This should allow most multimedia device drivers
to probe and control their clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The GPU clocks on msm8996 have three dedicated PLLs, MMPLL2,
MMPLL8, and MMPLL9. We leave MMPLL9 at the maximum speed (624
MHz), and we use MMPLL2 and MMPLL8 for the other frequencies. To
make switching frequencies faster, we ping-pong between MMPLL2
and MMPLL8 when we're switching between frequencies that aren't
the maximum. Implement custom rcg clk ops for this type of
frequency switching.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add support for the global clock controller found on MSM8996
based devices. This should allow most non-multimedia device
drivers to probe and control their clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add support for configuring rates of, enabling, and disabling
Alpha PLLs. This is sufficient for the types of PLLs found in
the global and multimedia clock controllers.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Move the xo and sleep clocks to device-tree, instead of hard-coding
them in the driver. This allows us to insert the RPM clocks (if they
are enabled) in between the on-board oscillators and the actual clock.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
All these clock controllers are little endian devices, but so far
we've been relying on the regmap mmio bus handling this for us
without explicitly stating that fact. After commit 4a98da2164cf
(regmap-mmio: Use native endianness for read/write, 2015-10-29),
the regmap mmio bus will read/write with the __raw_*() IO
accessors, instead of using the readl/writel() APIs that do
proper byte swapping for little endian devices.
So if we're running on a big endian processor and haven't
specified the endianness explicitly in the regmap config or in
DT, we're going to switch from doing little endian byte swapping
to big endian accesses without byte swapping, leading to some
confusing results. On my apq8074 dragonboard, this causes the
device to fail to boot as we access the clock controller with
big endian IO accesses even though the device is little endian.
Specify the endianness explicitly so that the regmap core
properly byte swaps the accesses for us.
Reported-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Tyler Baker <tyler.baker@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Cc: Simon Arlott <simon@fire.lp0.eu>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Put these clocks into the dt files instead of registering them
from C code. This provides a few benefits. It allows us to
specify the frequency of these clocks at the board level instead
of hard-coding them in the driver. It allows us to insert an RPM
clock in between the consumers of the crystals and the actual
clock. And finally, it helps us transition the GCC driver to use
RPM clocks when that configuration is enabled.
Cc: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We want to put the XO board clocks into the dt files, but we also
need to be backwards compatible with an older dtb. Add an API to
the common code to do this. This also makes a place for us to
handle the case when the RPM clock driver is enabled and we don't
want to register the fixed factor clock.
Cc: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The halt bits for these clocks seem wrong. I get the following
warning while booting on an msm8960-cdp:
WARNING: CPU: 0 PID: 1 at drivers/clk/qcom/clk-branch.c:97 clk_branch_toggle+0xd0/0x138()
dsi1_clk status stuck at 'on'
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.3.0-rc3-00113-g5532cfb567fe #110
Hardware name: Qualcomm (Flattened Device Tree)
[<c0216984>] (unwind_backtrace) from [<c02138f8>] (show_stack+0x10/0x14)
[<c02138f8>] (show_stack) from [<c04a525c>] (dump_stack+0x70/0xbc)
[<c04a525c>] (dump_stack) from [<c0223c70>] (warn_slowpath_common+0x78/0xb4)
[<c0223c70>] (warn_slowpath_common) from [<c0223d40>] (warn_slowpath_fmt+0x30/0x40)
[<c0223d40>] (warn_slowpath_fmt) from [<c05fc2dc>] (clk_branch_toggle+0xd0/0x138)
[<c05fc2dc>] (clk_branch_toggle) from [<c05f3f3c>] (clk_disable_unused_subtree+0x98/0x1b0)
[<c05f3f3c>] (clk_disable_unused_subtree) from [<c05f3ec4>] (clk_disable_unused_subtree+0x20/0x1b0)
[<c05f3ec4>] (clk_disable_unused_subtree) from [<c05f5474>] (clk_disable_unused+0x58/0xd8)
[<c05f5474>] (clk_disable_unused) from [<c0209710>] (do_one_initcall+0xac/0x1ec)
[<c0209710>] (do_one_initcall) from [<c0991db4>] (kernel_init_freeable+0x11c/0x1e8)
[<c0991db4>] (kernel_init_freeable) from [<c0727ae0>] (kernel_init+0x8/0xec)
[<c0727ae0>] (kernel_init) from [<c0210238>] (ret_from_fork+0x14/0x3c)
Fix the status bits and the errors go away.
Fixes: 5532cfb567 ("clk: qcom: mmcc-8960: Add DSI related clocks")
Acked-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add rcg and branch clk structs for DSI1 and DSI2 blocks found in MSM8960
and APQ8064. Each DSI instance has 4 pairs of rcg and branch clocks.
Populate arrays mmcc_msm8960_clks and mmcc_apq8064_clks with these clocks.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
DSI specific RCG clocks required customized clk_ops. There are
a total of 4 RCGs per DSI block: DSI, BYTE, ESC and PIXEL.
There are a total of 2 clocks coming from the DSI PLL, which serve as
inputs to these RCGs. The BYTE and ESC RCGs are fed by one of the
post dividers of DSI1 or DSI2 PLLs, and the DSI and PIXEL RCGs are fed by
another divider of the PLL.
In each of the 2 groups above, only one of the clocks sets its parent.
These are BYTE RCG and DSI RCG for each of the groups respectively, as
shown in the diagram below.
The DSI and BYTE RCGs serve as bypass clocks. We create a new set of ops
clk_rcg_bypass2_ops, which are like the regular bypass ops, but don't
take in a freq table, since the DSI driver using these clocks is
parent-able.
The PIXEL RCG needs to derive the required pixel clock using dsixpll.
It parses a m/n frac table to retrieve the correct clock.
The ESC RCG doesn't have a frac M/N block, it can just apply a pre-
divider. Its ops simply check if the required clock rate can be
achieved by the pre-divider.
+-------------------+
| |---dsixpllbyte---o---> To byte RCG
| | | (sets parent rate)
| | |
| | |
| DSI 1/2 PLL | |
| | o---> To esc RCG
| | (doesn't set parent rate)
| |
| |----dsixpll-----o---> To dsi RCG
+-------------------+ | (sets parent rate)
( x = 1, 2 ) |
|
o---> To pixel rcg
(doesn't set parent rate)
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
8960 family of devices have TSENS as part of GCC in hardware.
Hence DT would represent a GCC node with GCC properties as well
as TSENS. Create a virtual platform child device here for TSENS
so the driver can probe it and use the parent (GCC) to extract DT
properties.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
[sboyd@codeaurora.org: Massaged to work with devm friendly
qcom_cc_probe()]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Having this hidden config below the COMMON_CLK_QCOM config causes
menuconfig to stop indenting config items after it.
<*> Support for Qualcomm's clock controllers
{M} APQ8084 Global Clock Controller
<M> APQ8084 Multimedia Clock Controller
{M} IPQ806x Global Clock Controller
<M> IPQ806x LPASS Clock Controller
<M> MSM8660 Global Clock Controller
<M> MSM8916 Global Clock Controller
{M} APQ8064/MSM8960 Global Clock Controller
<M> APQ8064/MSM8960 LPASS Clock Controller
<M> MSM8960 Multimedia Clock Controller
{M} MSM8974 Global Clock Controller
<M> MSM8974 Multimedia Clock Controller
Move it up above anything else so that we don't get odd
indenting.
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that qcom_cc_remove() is a nop, drop calls to
qcom_cc_remove() and any empty driver remove functions.
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some APIs in qcom_cc_probe() don't have a devm counterpart, so we
have to use the calling device's platform data to pass pointers
to the remove path. Let's use devm_add_action() instead, so that
the remove path doesn't need to do anything, allowing us to
remove qcom_cc_remove() entirely.
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The oxili_cx GDSC is inside the power domain of the oxili GDSC.
Add the dependency so that the CX domain can properly power up.
Reported-by: Rob Clark <robdclark@gmail.com>
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add support for the msm8916 audio clocks. This includes core bus,
low-power audio and codec clocks. They are required for audio playback.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add support for the msm8916 BIMC (Bus Integrated Memory Controller)
clocks that are needed for GPU.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some root clock generators may have child branches that are controlled
by different CPUs. These RCGs require some special operations:
- some enable bits have to be toggled when we set the rate;
- if RCG is disabled we only cache the rate and set it later when enabled;
- when the RCG is disabled, the mux is set to the safe source;
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
[sboyd@codeaurora.org: Simplify recalc_rate implementation]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add support for the msm8916 TCU (Translation Control Unit) clocks that
are needed for IOMMU.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add the GDSC instances that exist as part of apq8084 MMCC block.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add the GDSC instances that exist as part of apq8084 GCC block
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add the GDSC instances that exist as part of msm8974 MMCC block
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
There's just one GDSC as part of the msm8974 GCC block.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add all data for the GDSCs which are part of msm8916 GCC block.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Certain devices can have GDSCs' which support ON as the only state.
They can't be power collapsed to either hit RET or OFF.
The clients drivers for these GDSCs' however would expect the state
of the core to be reset following a GDSC disable and re-enable.
To do this assert/deassert reset lines every time the client
driver would request the GDSC to be powered on/off instead.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Along with the GDSC power switch, there is additional control
to either retain all memory (core and peripheral) within a given
powerdomain or to turn them off while the GDSC is powered down.
Add support for these by modelling a RET state where all
memory is retained and an OFF state where all memory gets turned
off.
The controls provided are granular enough to be able to support
various differnt levels of RET states, like a 'shallow RET' with all memory
retained and a 'deep RET' with some memory retained while some others
are lost. The current patch does not support this and considers
just one RET state where all memory is retained. Futher work, if
needed can support multiple different levels of RET state.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The common clk probe registers a clk provider and a reset controller.
Update it to register a genpd provider using the gdsc data provided
by each platform.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
GDSCs (Global Distributed Switch Controllers) are responsible for
safely collapsing and restoring power to peripherals in the SoC.
These are best modelled as power domains using genpd and given
the registers are scattered throughout the clock controller register
space, its best to have the support added through the clock driver.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Sometimes the display driver may want to change the parent PLL of
the display clocks (byte and pixel clocks) depending on the
use-case. Currently the parent is fixed by means of having a
frequency table with one entry that chooses a particular parent.
Remove this restriction and use the parent the clock is
configured for in the hardware during clk_set_rate(). This
requires consumers to rely on the default parent or to configure
the parent with clk_set_parent()/assigned-clock-parents on the
clocks before calling clk_set_rate().
Tested-by: Archit Taneja <architt@codeaurora.org>
Cc: Hai Li <hali@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Fix the enable bit of the pseudorandom number generator clock.
Reported-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Fixes: 3966fab8b6 "clk: qcom: Add MSM8916 Global Clock Controller support"
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Use the provider based method to get a clock's name so that we
can get rid of the clk member in struct clk_hw one day. Mostly
converted with the following coccinelle script.
@@
struct clk_hw *E;
@@
-__clk_get_name(E->clk)
+clk_hw_get_name(E)
Acked-by: Heiko Stuebner <heiko@sntech.de>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kevin Cernekee <cernekee@chromium.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
