This fixes a hang seen in jbd2_journal_release_jbd_inode
on a lot of Power 6 systems running with ext4. When we get
in the hung state, all I/O to the disk in question gets blocked
where we stay indefinitely. Looking at the task list, I can see
we are stuck in jbd2_journal_release_jbd_inode waiting on a
wake up. I added some debug code to detect this scenario and
dump additional data if we were stuck in jbd2_journal_release_jbd_inode
for longer than 30 minutes. When it hit, I was able to see that
i_flags was 0, suggesting we missed the wake up.
This patch changes i_flags to be an unsigned long, uses bit operators
to access it, and adds barriers around the accesses. Prior to applying
this patch, we were regularly hitting this hang on numerous systems
in our test environment. After applying the patch, the hangs no longer
occur.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (40 commits)
ext4: Adding error check after calling ext4_mb_regular_allocator()
ext4: Fix dirtying of journalled buffers in data=journal mode
ext4: re-inline ext4_rec_len_(to|from)_disk functions
jbd2: Remove t_handle_lock from start_this_handle()
jbd2: Change j_state_lock to be a rwlock_t
jbd2: Use atomic variables to avoid taking t_handle_lock in jbd2_journal_stop
ext4: Add mount options in superblock
ext4: force block allocation on quota_off
ext4: fix freeze deadlock under IO
ext4: drop inode from orphan list if ext4_delete_inode() fails
ext4: check to make make sure bd_dev is set before dereferencing it
jbd2: Make barrier messages less scary
ext4: don't print scary messages for allocation failures post-abort
ext4: fix EFBIG edge case when writing to large non-extent file
ext4: fix ext4_get_blocks references
ext4: Always journal quota file modifications
ext4: Fix potential memory leak in ext4_fill_super
ext4: Don't error out the fs if the user tries to make a file too big
ext4: allocate stripe-multiple IOs on stripe boundaries
ext4: move aio completion after unwritten extent conversion
...
Fix up conflicts in fs/ext4/inode.c as per Ted.
Fix up xfs conflicts as per earlier xfs merge.
This should remove the last exclusive lock from start_this_handle(),
so that we should now be able to start multiple transactions at the
same time on large SMP systems.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Lockstat reports have shown that j_state_lock is a major source of
lock contention, especially on systems with more than 4 CPU cores. So
change it to be a read/write spinlock.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
By using an atomic_t for t_updates and t_outstanding credits, this
should allow us to not need to take transaction t_handle_lock in
jbd2_journal_stop().
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
__GFP_NOFAIL is going away, so add our own retry loop. Also add
jbd2__journal_start() and jbd2__journal_restart() which take a gfp
mask, so that file systems can optionally (re)start transaction
handles using GFP_KERNEL. If they do this, then they need to be
prepared to handle receiving an PTR_ERR(-ENOMEM) error, and be ready
to reflect that error up to userspace.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
OCFS2 uses t_commit trigger to compute and store checksum of the just
committed blocks. When a buffer has b_frozen_data, checksum is computed
for it instead of b_data but this can result in an old checksum being
written to the filesystem in the following scenario:
1) transaction1 is opened
2) handle1 is opened
3) journal_access(handle1, bh)
- This sets jh->b_transaction to transaction1
4) modify(bh)
5) journal_dirty(handle1, bh)
6) handle1 is closed
7) start committing transaction1, opening transaction2
8) handle2 is opened
9) journal_access(handle2, bh)
- This copies off b_frozen_data to make it safe for transaction1 to commit.
jh->b_next_transaction is set to transaction2.
10) jbd2_journal_write_metadata() checksums b_frozen_data
11) the journal correctly writes b_frozen_data to the disk journal
12) handle2 is closed
- There was no dirty call for the bh on handle2, so it is never queued for
any more journal operation
13) Checkpointing finally happens, and it just spools the bh via normal buffer
writeback. This will write b_data, which was never triggered on and thus
contains a wrong (old) checksum.
This patch fixes the problem by calling the trigger at the moment data is
frozen for journal commit - i.e., either when b_frozen_data is created by
do_get_write_access or just before we write a buffer to the log if
b_frozen_data does not exist. We also rename the trigger to t_frozen as
that better describes when it is called.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6: (33 commits)
quota: stop using QUOTA_OK / NO_QUOTA
dquot: cleanup dquot initialize routine
dquot: move dquot initialization responsibility into the filesystem
dquot: cleanup dquot drop routine
dquot: move dquot drop responsibility into the filesystem
dquot: cleanup dquot transfer routine
dquot: move dquot transfer responsibility into the filesystem
dquot: cleanup inode allocation / freeing routines
dquot: cleanup space allocation / freeing routines
ext3: add writepage sanity checks
ext3: Truncate allocated blocks if direct IO write fails to update i_size
quota: Properly invalidate caches even for filesystems with blocksize < pagesize
quota: generalize quota transfer interface
quota: sb_quota state flags cleanup
jbd: Delay discarding buffers in journal_unmap_buffer
ext3: quota_write cross block boundary behaviour
quota: drop permission checks from xfs_fs_set_xstate/xfs_fs_set_xquota
quota: split out compat_sys_quotactl support from quota.c
quota: split out netlink notification support from quota.c
quota: remove invalid optimization from quota_sync_all
...
Fixed trivial conflicts in fs/namei.c and fs/ufs/inode.c
CONFIG_BUFFER_DEBUG seems to have been removed from the documentation
somewhere around 2.4.15 and seemingly hasn't been available even
longer. It is, however, still referenced at one place from the jbd
code (one is a copy of the other header). Time to clean it up
Signed-off-by: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de>
Signed-off-by: Jan Kara <jack@suse.cz>
This is a bit complicated because we are trying to optimize when we
send barriers to the fs data disk. We could just throw in an extra
barrier to the data disk whenever we send a barrier to the journal
disk, but that's not always strictly necessary.
We only need to send a barrier during a commit when there are data
blocks which are must be written out due to an inode written in
ordered mode, or if fsync() depends on the commit to force data blocks
to disk. Finally, before we drop transactions from the beginning of
the journal during a checkpoint operation, we need to guarantee that
any blocks that were flushed out to the data disk are firmly on the
rust platter before we drop the transaction from the journal.
Thanks to Oleg Drokin for pointing out this flaw in ext3/ext4.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Now that the SLUB seems to be fixed so that it respects the requested
alignment, use kmem_cache_alloc() to allocator if the block size of
the buffer heads to be allocated is less than the page size.
Previously, we were using 16k page on a Power system for each buffer,
even when the file system was using 1k or 4k block size.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The /proc/fs/jbd2/<dev>/history was maintained manually; by using
tracepoints, we can get all of the existing functionality of the /proc
file plus extra capabilities thanks to the ftrace infrastructure. We
save memory as a bonus.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This fixes sparse noise:
error: dubious one-bit signed bitfield
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: Jan Kara <jack@ucw.cz>
The revoke records must be written using the same way as the rest of
the blocks during the commit process; that is, either marked as
synchronous writes or as asynchornous writes.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
If a commit is triggered by fsync(), set a flag indicating the journal
blocks associated with the transaction should be flushed out using
WRITE_SYNC.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
If we race with commit code setting i_transaction to NULL, we could
possibly dereference it. Proper locking requires the journal pointer
(to access journal->j_list_lock), which we don't have. So we have to
change the prototype of the function so that filesystem passes us the
journal pointer. Also add a more detailed comment about why the
function jbd2_journal_begin_ordered_truncate() does what it does and
how it should be used.
Thanks to Dan Carpenter <error27@gmail.com> for pointing to the
suspitious code.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Acked-by: Joel Becker <joel.becker@oracle.com>
CC: linux-ext4@vger.kernel.org
CC: ocfs2-devel@oss.oracle.com
CC: mfasheh@suse.de
CC: Dan Carpenter <error27@gmail.com>
Otherwise it can be very confusing to find a "EXT3-fs: " failure in
the middle of EXT4-fs failures, and it makes it harder to track the
source of the failure.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (57 commits)
jbd2: Fix oops in jbd2_journal_init_inode() on corrupted fs
ext4: Remove "extents" mount option
block: Add Kconfig help which notes that ext4 needs CONFIG_LBD
ext4: Make printk's consistently prefixed with "EXT4-fs: "
ext4: Add sanity checks for the superblock before mounting the filesystem
ext4: Add mount option to set kjournald's I/O priority
jbd2: Submit writes to the journal using WRITE_SYNC
jbd2: Add pid and journal device name to the "kjournald2 starting" message
ext4: Add markers for better debuggability
ext4: Remove code to create the journal inode
ext4: provide function to release metadata pages under memory pressure
ext3: provide function to release metadata pages under memory pressure
add releasepage hooks to block devices which can be used by file systems
ext4: Fix s_dirty_blocks_counter if block allocation failed with nodelalloc
ext4: Init the complete page while building buddy cache
ext4: Don't allow new groups to be added during block allocation
ext4: mark the blocks/inode bitmap beyond end of group as used
ext4: Use new buffer_head flag to check uninit group bitmaps initialization
ext4: Fix the race between read_inode_bitmap() and ext4_new_inode()
ext4: code cleanup
...
Filesystems often to do compute intensive operation on some
metadata. If this operation is repeated many times, it can be very
expensive. It would be much nicer if the operation could be performed
once before a buffer goes to disk.
This adds triggers to jbd2 buffer heads. Just before writing a metadata
buffer to the journal, jbd2 will optionally call a commit trigger associated
with the buffer. If the journal is aborted, an abort trigger will be
called on any dirty buffers as they are dropped from pending
transactions.
ocfs2 will use this feature.
Initially I tried to come up with a more generic trigger that could be
used for non-buffer-related events like transaction completion. It
doesn't tie nicely, because the information a buffer trigger needs
(specific to a journal_head) isn't the same as what a transaction
trigger needs (specific to a tranaction_t or perhaps journal_t). So I
implemented a buffer set, with the understanding that
journal/transaction wide triggers should be implemented separately.
There is only one trigger set allowed per buffer. I can't think of any
reason to attach more than one set. Contrast this with a journal or
transaction in which multiple places may want to watch the entire
transaction separately.
The trigger sets are considered static allocation from the jbd2
perspective. ocfs2 will just have one trigger set per block type,
setting the same set on every bh of the same type.
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Add this so that file systems using JBD2 can safely allocate unused b_state
bits.
In this case, we add it so that Ocfs2 can define a single bit for tracking
the validation state of a buffer.
Acked-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
This code has been obsolete in quite some time, since the supported
method for adding a journal inode is to use tune2fs (or to creating
new filesystem with a journal via mke2fs or mkfs.ext4).
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Avoid freeing the transaction in __jbd2_journal_drop_transaction() so
the journal commit callback can run without holding j_list_lock, to
avoid lock contention on this spinlock.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
jbd2_log_do_checkpoint()n is one of the kernel's largest stack users.
Move the array of buffer head's from the stack of jbd2_log_do_checkpoint()
to the in-core journal structure.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Add new mount options, min_batch_time and max_batch_time, which
controls how long the jbd2 layer should wait for additional filesystem
operations to get batched with a synchronous write transaction.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This patch removes the static sleep time in favor of a more self
optimizing approach where we measure the average amount of time it
takes to commit a transaction to disk and the ammount of time a
transaction has been running. If somebody does a sync write or an
fsync() traditionally we would sleep for 1 jiffies, which depending on
the value of HZ could be a significant amount of time compared to how
long it takes to commit a transaction to the underlying storage. With
this patch instead of sleeping for a jiffie, we check to see if the
amount of time this transaction has been running is less than the
average commit time, and if it is we sleep for the delta using
schedule_hrtimeout to give us a higher precision sleep time. This
greatly benefits high end storage where you could end up sleeping for
longer than it takes to commit the transaction and therefore sitting
idle instead of allowing the transaction to be committed by keeping
the sleep time to a minimum so you are sure to always be doing
something.
Signed-off-by: Josef Bacik <jbacik@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Add this so that file systems using JBD2 can safely allocate unused b_state
bits.
In this case, we add it so that Ocfs2 can define a single bit for tracking
the validation state of a buffer.
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The multiblock allocator needs to be able to release blocks (and issue
a blkdev discard request) when the transaction which freed those
blocks is committed. Previously this was done via a polling mechanism
when blocks are allocated or freed. A much better way of doing things
is to create a jbd2 callback function and attaching the list of blocks
to be freed directly to the transaction structure.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the journal doesn't abort when it gets an IO error in file data
blocks, the file data corruption will spread silently. Because
most of applications and commands do buffered writes without fsync(),
they don't notice the IO error. It's scary for mission critical
systems. On the other hand, if the journal aborts whenever it gets
an IO error in file data blocks, the system will easily become
inoperable. So this patch introduces a filesystem option to
determine whether it aborts the journal or just call printk() when
it gets an IO error in file data.
If you mount an ext4 fs with data_err=abort option, it aborts on file
data write error. If you mount it with data_err=ignore, it doesn't
abort, just call printk(). data_err=ignore is the default.
Here is the corresponding patch of the ext3 version:
http://kerneltrap.org/mailarchive/linux-kernel/2008/9/9/3239374
Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
When a checkpointing IO fails, current JBD2 code doesn't check the
error and continue journaling. This means latest metadata can be
lost from both the journal and filesystem.
This patch leaves the failed metadata blocks in the journal space
and aborts journaling in the case of jbd2_log_do_checkpoint().
To achieve this, we need to do:
1. don't remove the failed buffer from the checkpoint list where in
the case of __try_to_free_cp_buf() because it may be released or
overwritten by a later transaction
2. jbd2_log_do_checkpoint() is the last chance, remove the failed
buffer from the checkpoint list and abort the journal
3. when checkpointing fails, don't update the journal super block to
prevent the journaled contents from being cleaned. For safety,
don't update j_tail and j_tail_sequence either
4. when checkpointing fails, notify this error to the ext4 layer so
that ext4 don't clear the needs_recovery flag, otherwise the
journaled contents are ignored and cleaned in the recovery phase
5. if the recovery fails, keep the needs_recovery flag
6. prevent jbd2_cleanup_journal_tail() from being called between
__jbd2_journal_drop_transaction() and jbd2_journal_abort()
(a possible race issue between jbd2_log_do_checkpoint()s called by
jbd2_journal_flush() and __jbd2_log_wait_for_space())
Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Calculate the journal device name once and stash it away in the
journal_s structure. This avoids needing to call bdevname()
everywhere and reduces stack usage by not needing to allocate an
on-stack buffer. In addition, we eliminate the '/' that can appear in
device names (e.g. "cciss/c0d0p9" --- see kernel bugzilla #11321) that
can cause problems when creating proc directory names, and include the
inode number to support ocfs2 which creates multiple journals with
different inode numbers.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This patch adds necessary framework into JBD2 to be able to track inodes
with each transaction and write-out their dirty data during transaction
commit time.
This new ordered mode brings all sorts of advantages such as possibility
to get rid of journal heads and buffer heads for data buffers in ordered
mode, better ordering of writes on transaction commit, simplification of
some JBD code, no more anonymous pages when truncate of data being
committed happens. Also with this new ordered mode, delayed allocation
on ordered mode is much simpler.
Signed-off-by: Jan Kara <jack@suse.cz>
Carlo Wood has demonstrated that it's possible to recover deleted
files from the journal. Something that will make this easier is if we
can put the time of the commit into commit block.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
If a journal checksum error is detected, the ext4 filesystem will call
ext4_error(), and the mount will either continue, become a read-only
mount, or cause a kernel panic based on the superblock flags
indicating the user's preference of what to do in case of filesystem
corruption being detected.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
None of these files use any of the functionality promised by
asm/semaphore.h. It's possible that they (or some user of them) rely
on it dragging in some unrelated header file, but I can't build all
these files, so we'll have to fix any build failures as they come up.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
The journal checksum feature adds two new flags i.e
JBD2_FEATURE_INCOMPAT_ASYNC_COMMIT and JBD2_FEATURE_COMPAT_CHECKSUM.
JBD2_FEATURE_CHECKSUM flag indicates that the commit block contains the
checksum for the blocks described by the descriptor blocks.
Due to checksums, writing of the commit record no longer needs to be
synchronous. Now commit record can be sent to disk without waiting for
descriptor blocks to be written to disk. This behavior is controlled
using JBD2_FEATURE_ASYNC_COMMIT flag. Older kernels/e2fsck should not be
able to recover the journal with _ASYNC_COMMIT hence it is made
incompat.
The commit header has been extended to hold the checksum along with the
type of the checksum.
For recovery in pass scan checksums are verified to ensure the sanity
and completeness(in case of _ASYNC_COMMIT) of every transaction.
Signed-off-by: Andreas Dilger <adilger@clusterfs.com>
Signed-off-by: Girish Shilamkar <girish@clusterfs.com>
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
The patch below updates the jbd stats patch to 2.6.20/jbd2.
The initial patch was posted by Alex Tomas in December 2005
(http://marc.info/?l=linux-ext4&m=113538565128617&w=2).
It provides statistics via procfs such as transaction lifetime and size.
Sometimes, investigating performance problems, i find useful to have
stats from jbd about transaction's lifetime, size, etc. here is a
patch for review and inclusion probably.
for example, stats after creation of 3M files in htree directory:
[root@bob ~]# cat /proc/fs/jbd/sda/history
R/C tid wait run lock flush log hndls block inlog ctime write drop close
R 261 8260 2720 0 0 750 9892 8170 8187
C 259 750 0 4885 1
R 262 20 2200 10 0 770 9836 8170 8187
R 263 30 2200 10 0 3070 9812 8170 8187
R 264 0 5000 10 0 1340 0 0 0
C 261 8240 3212 4957 0
R 265 8260 1470 0 0 4640 9854 8170 8187
R 266 0 5000 10 0 1460 0 0 0
C 262 8210 2989 4868 0
R 267 8230 1490 10 0 4440 9875 8171 8188
R 268 0 5000 10 0 1260 0 0 0
C 263 7710 2937 4908 0
R 269 7730 1470 10 0 3330 9841 8170 8187
R 270 0 5000 10 0 830 0 0 0
C 265 8140 3234 4898 0
C 267 720 0 4849 1
R 271 8630 2740 20 0 740 9819 8170 8187
C 269 800 0 4214 1
R 272 40 2170 10 0 830 9716 8170 8187
R 273 40 2280 0 0 3530 9799 8170 8187
R 274 0 5000 10 0 990 0 0 0
where,
R - line for transaction's life from T_RUNNING to T_FINISHED
C - line for transaction's checkpointing
tid - transaction's id
wait - for how long we were waiting for new transaction to start
(the longest period journal_start() took in this transaction)
run - real transaction's lifetime (from T_RUNNING to T_LOCKED
lock - how long we were waiting for all handles to close
(time the transaction was in T_LOCKED)
flush - how long it took to flush all data (data=ordered)
log - how long it took to write the transaction to the log
hndls - how many handles got to the transaction
block - how many blocks got to the transaction
inlog - how many blocks are written to the log (block + descriptors)
ctime - how long it took to checkpoint the transaction
write - how many blocks have been written during checkpointing
drop - how many blocks have been dropped during checkpointing
close - how many running transactions have been closed to checkpoint this one
all times are in msec.
[root@bob ~]# cat /proc/fs/jbd/sda/info
280 transaction, each upto 8192 blocks
average:
1633ms waiting for transaction
3616ms running transaction
5ms transaction was being locked
1ms flushing data (in ordered mode)
1799ms logging transaction
11781 handles per transaction
5629 blocks per transaction
5641 logged blocks per transaction
Signed-off-by: Johann Lombardi <johann.lombardi@bull.net>
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Before we start committing a transaction, we call
__journal_clean_checkpoint_list() to cleanup transaction's written-back
buffers.
If this call happens to remove all of them (and there were already some
buffers), __journal_remove_checkpoint() will decide to free the transaction
because it isn't (yet) a committing transaction and soon we fail some
assertion - the transaction really isn't ready to be freed :).
We change the check in __journal_remove_checkpoint() to free only a
transaction in T_FINISHED state. The locking there is subtle though (as
everywhere in JBD ;(). We use j_list_lock to protect the check and a
subsequent call to __journal_drop_transaction() and do the same in the end
of journal_commit_transaction() which is the only place where a transaction
can get to T_FINISHED state.
Probably I'm too paranoid here and such locking is not really necessary -
checkpoint lists are processed only from log_do_checkpoint() where a
transaction must be already committed to be processed or from
__journal_clean_checkpoint_list() where kjournald itself calls it and thus
transaction cannot change state either. Better be safe if something
changes in future...
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
JBD2: Replace slab allocations with page allocations
JBD2 allocate memory for committed_data and frozen_data from slab. However
JBD2 should not pass slab pages down to the block layer. Use page allocator
pages instead. This will also prepare JBD for the large blocksize patchset.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
The jbd2-debug file used to be located in /proc/sys/fs/jbd2-debug, but it
incorrectly used create_proc_entry() instead of the sysctl routines, and
no proc entry was ever created.
Instead of fixing this we might as well move the jbd2-debug file to
debugfs which would be the preferred location for this kind of tunable.
The new location is now /sys/kernel/debug/jbd2/jbd2-debug.
Signed-off-by: Jose R. Santos <jrs@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
When the JBD code was forked to create the new JBD2 code base, the
references to CONFIG_JBD_DEBUG where never changed to
CONFIG_JBD2_DEBUG. This patch fixes that.
Signed-off-by: Jose R. Santos <jrs@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Replace all uses of kmem_cache_t with struct kmem_cache.
The patch was generated using the following script:
#!/bin/sh
#
# Replace one string by another in all the kernel sources.
#
set -e
for file in `find * -name "*.c" -o -name "*.h"|xargs grep -l $1`; do
quilt add $file
sed -e "1,\$s/$1/$2/g" $file >/tmp/$$
mv /tmp/$$ $file
quilt refresh
done
The script was run like this
sh replace kmem_cache_t "struct kmem_cache"
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
