Pull i2c updates from Wolfram Sang:
"Here is the pull request from the i2c subsystem. It got a little
delayed because I needed to wait for a dependency to be included
(commit b424080a9e: "reset: Add optional resets and stubs"). Plus,
I had some email problems. All done now, the highlights are:
- drivers can now deprecate their use of i2c classes. That shouldn't
be used on embedded platforms anyhow and was often blindly
copy&pasted. This mechanism gives users time to switch away and
ultimately boot faster once the use of classes for those drivers is
gone for good.
- new drivers for QUP, Cadence, efm32
- tracepoint support for I2C and SMBus
- bigger cleanups for the mv64xxx, nomadik, and designware drivers
And the usual bugfixes, cleanups, feature additions. Most stuff has
been in linux-next for a while. Just some hot fixes and new drivers
were added a bit more recently."
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (63 commits)
i2c: cadence: fix Kconfig dependency
i2c: Add driver for Cadence I2C controller
i2c: cadence: Document device tree bindings
Documentation: i2c: improve section about flags mangling the protocol
i2c: qup: use proper type fro clk_freq
i2c: qup: off by ones in qup_i2c_probe()
i2c: efm32: fix binding doc
MAINTAINERS: update I2C web resources
i2c: qup: New bus driver for the Qualcomm QUP I2C controller
i2c: qup: Add device tree bindings information
i2c: i2c-xiic: deprecate class based instantiation
i2c: i2c-sirf: deprecate class based instantiation
i2c: i2c-mv64xxx: deprecate class based instantiation
i2c: i2c-designware-platdrv: deprecate class based instantiation
i2c: i2c-davinci: deprecate class based instantiation
i2c: i2c-bcm2835: deprecate class based instantiation
i2c: mv64xxx: Fix reset controller handling
i2c: omap: fix usage of IS_ERR_VALUE with pm_runtime_get_sync
i2c: efm32: new bus driver
i2c: exynos5: remove unnecessary cast of void pointer
...
Core:
- CONFIG_MMC_UNSAFE_RESUME=y is now default behavior.
- DT bindings for SDHCI UHS, eMMC HS200, high-speed DDR, at 1.8/1.2V.
- Add GPIO descriptor based slot-gpio card detect API.
Drivers:
- dw_mmc: Refactor SOCFPGA support as a variant inside dw_mmc-pltfm.c.
- mmci: Support HW busy detection on ux500.
- omap: Support MMC_ERASE.
- omap_hsmmc: Support MMC_PM_KEEP_POWER, MMC_PM_WAKE_SDIO_IRQ, (a)cmd23.
- rtsx: Support pre-req/post-req async.
- sdhci: Add support for Realtek RTS5250 controllers.
- sdhci-acpi: Add support for 80860F16, fix 80860F14/SDIO card detect.
- sdhci-msm: Add new driver for Qualcomm SDHCI chipset support.
- sdhci-pxav3: Add support for Marvell Armada 380 and 385 SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=6S8w
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.15:
Core:
- CONFIG_MMC_UNSAFE_RESUME=y is now default behavior
- DT bindings for SDHCI UHS, eMMC HS200, high-speed DDR, at 1.8/1.2V
- Add GPIO descriptor based slot-gpio card detect API
Drivers:
- dw_mmc: Refactor SOCFPGA support as a variant inside dw_mmc-pltfm.c
- mmci: Support HW busy detection on ux500
- omap: Support MMC_ERASE
- omap_hsmmc: Support MMC_PM_KEEP_POWER, MMC_PM_WAKE_SDIO_IRQ, (a)cmd23
- rtsx: Support pre-req/post-req async
- sdhci: Add support for Realtek RTS5250 controllers
- sdhci-acpi: Add support for 80860F16, fix 80860F14/SDIO card detect
- sdhci-msm: Add new driver for Qualcomm SDHCI chipset support
- sdhci-pxav3: Add support for Marvell Armada 380 and 385 SoCs"
* tag 'mmc-updates-for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (102 commits)
mmc: sdhci-acpi: Intel SDIO has broken card detect
mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller
mmc: sdhci-msm: Add platform_execute_tuning implementation
mmc: sdhci-msm: Initial support for Qualcomm chipsets
mmc: sdhci-msm: Qualcomm SDHCI binding documentation
sdhci: only reprogram retuning timer when flag is set
mmc: rename ARCH_BCM to ARCH_BCM_MOBILE
mmc: sdhci: Allow for irq being shared
mmc: sdhci-acpi: Add device id 80860F16
mmc: sdhci-acpi: Fix broken card detect for ACPI HID 80860F14
mmc: slot-gpio: Add GPIO descriptor based CD GPIO API
mmc: slot-gpio: Split out CD IRQ request into a separate function
mmc: slot-gpio: Record GPIO descriptors instead of GPIO numbers
Revert "dts: socfpga: Add support for SD/MMC on the SOCFPGA platform"
mmc: sdhci-spear: use generic card detection gpio support
mmc: sdhci-spear: remove support for power gpio
mmc: sdhci-spear: simplify resource handling
mmc: sdhci-spear: fix platform_data usage
mmc: sdhci-spear: fix error handling paths for DT
mmc: sdhci-bcm-kona: fix build errors when built-in
...
Pull more powerpc updates from Ben Herrenschmidt:
"Here are a few more powerpc things for you.
So you'll find here the conversion of the two new firmware sysfs
interfaces to the new API for self-removing files that Greg and Tejun
introduced, so they can finally remove the old one.
I'm also reverting the hwmon driver for powernv. I shouldn't have
merged it, I got a bit carried away here. I hadn't realized it was
never CCed to the relevant maintainer(s) and list(s), and happens to
have some issues so I'm taking it out and it will come back via the
proper channels.
The rest is a bunch of LE fixes (argh, some of the new stuff was
broken on LE, I really need to start testing LE myself !) and various
random fixes here and there.
Finally one bit that's not strictly a fix, which is the HVC OPAL
change to "kick" the HVC thread when the firmware tells us there is
new incoming data. I don't feel like waiting for this one, it's
simple enough, and it makes a big difference in console responsiveness
which is good for my nerves"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (26 commits)
powerpc/powernv Adapt opal-elog and opal-dump to new sysfs_remove_file_self
Revert "powerpc/powernv: hwmon driver for power values, fan rpm and temperature"
power, sched: stop updating inside arch_update_cpu_topology() when nothing to be update
powerpc/le: Avoid creatng R_PPC64_TOCSAVE relocations for modules.
arch/powerpc: Use RCU_INIT_POINTER(x, NULL) in platforms/cell/spu_syscalls.c
powerpc/opal: Add missing include
powerpc: Convert last uses of __FUNCTION__ to __func__
powerpc: Add lq/stq emulation
powerpc/powernv: Add invalid OPAL call
powerpc/powernv: Add OPAL message log interface
powerpc/book3s: Fix mc_recoverable_range buffer overrun issue.
powerpc: Remove dead code in sycall entry
powerpc: Use of_node_init() for the fakenode in msi_bitmap.c
powerpc/mm: NUMA pte should be handled via slow path in get_user_pages_fast()
powerpc/powernv: Fix endian issues with sensor code
powerpc/powernv: Fix endian issues with OPAL async code
tty/hvc_opal: Kick the HVC thread on OPAL console events
powerpc/powernv: Add opal_notifier_unregister() and export to modules
powerpc/ppc64: Do not turn AIL (reloc-on interrupts) too early
powerpc/ppc64: Gracefully handle early interrupts
...
Jan Stancek reported:
"pthread_cond_broadcast/4-1.c testcase from openposix testsuite (LTP)
occasionally fails, because some threads fail to wake up.
Testcase creates 5 threads, which are all waiting on same condition.
Main thread then calls pthread_cond_broadcast() without holding mutex,
which calls:
futex(uaddr1, FUTEX_CMP_REQUEUE_PRIVATE, 1, 2147483647, uaddr2, ..)
This immediately wakes up single thread A, which unlocks mutex and
tries to wake up another thread:
futex(uaddr2, FUTEX_WAKE_PRIVATE, 1)
If thread A manages to call futex_wake() before any waiters are
requeued for uaddr2, no other thread is woken up"
The ordering constraints for the hash bucket waiter counting are that
the waiter counts have to be incremented _before_ getting the spinlock
(because the spinlock acts as part of the memory barrier), but the
"requeue" operation didn't honor those rules, and nobody had even
thought about that case.
This fairly simple patch just increments the waiter count for the target
hash bucket (hb2) when requeing a futex before taking the locks. It
then decrements them again after releasing the lock - the code that
actually moves the futex(es) between hash buckets will do the additional
required waiter count housekeeping.
Reported-and-tested-by: Jan Stancek <jstancek@redhat.com>
Acked-by: Davidlohr Bueso <davidlohr@hp.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org # 3.14
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We are currently using sysfs_schedule_callback() which is deprecated
and about to be removed. Switch to the new interface instead.
Signed-off-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This reverts commit 0de7f8a917.
This driver wasn't merged via the proper maintainers (my fault ... ooops !)
and has serious issues so let's take it out for now and have a new better
one be merged the right way
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
Since v1:
Edited the comment according to Srivatsa's suggestion.
During the testing, we encounter below WARN followed by Oops:
WARNING: at kernel/sched/core.c:6218
...
NIP [c000000000101660] .build_sched_domains+0x11d0/0x1200
LR [c000000000101358] .build_sched_domains+0xec8/0x1200
PACATMSCRATCH [800000000000f032]
Call Trace:
[c00000001b103850] [c000000000101358] .build_sched_domains+0xec8/0x1200
[c00000001b1039a0] [c00000000010aad4] .partition_sched_domains+0x484/0x510
[c00000001b103aa0] [c00000000016d0a8] .rebuild_sched_domains+0x68/0xa0
[c00000001b103b30] [c00000000005cbf0] .topology_work_fn+0x10/0x30
...
Oops: Kernel access of bad area, sig: 11 [#1]
...
NIP [c00000000045c000] .__bitmap_weight+0x60/0xf0
LR [c00000000010132c] .build_sched_domains+0xe9c/0x1200
PACATMSCRATCH [8000000000029032]
Call Trace:
[c00000001b1037a0] [c000000000288ff4] .kmem_cache_alloc_node_trace+0x184/0x3a0
[c00000001b103850] [c00000000010132c] .build_sched_domains+0xe9c/0x1200
[c00000001b1039a0] [c00000000010aad4] .partition_sched_domains+0x484/0x510
[c00000001b103aa0] [c00000000016d0a8] .rebuild_sched_domains+0x68/0xa0
[c00000001b103b30] [c00000000005cbf0] .topology_work_fn+0x10/0x30
...
This was caused by that 'sd->groups == NULL' after building groups, which
was caused by the empty 'sd->span'.
The cpu's domain contained nothing because the cpu was assigned to a wrong
node, due to the following unfortunate sequence of events:
1. The hypervisor sent a topology update to the guest OS, to notify changes
to the cpu-node mapping. However, the update was actually redundant - i.e.,
the "new" mapping was exactly the same as the old one.
2. Due to this, the 'updated_cpus' mask turned out to be empty after exiting
the 'for-loop' in arch_update_cpu_topology().
3. So we ended up calling stop-machine() with an empty cpumask list, which made
stop-machine internally elect cpumask_first(cpu_online_mask), i.e., CPU0 as
the cpu to run the payload (the update_cpu_topology() function).
4. This causes update_cpu_topology() to be run by CPU0. And since 'updates'
is kzalloc()'ed inside arch_update_cpu_topology(), update_cpu_topology()
finds update->cpu as well as update->new_nid to be 0. In other words, we
end up assigning CPU0 (and eventually its siblings) to node 0, incorrectly.
Along with the following wrong updating, it causes the sched-domain rebuild
code to break and crash the system.
Fix this by skipping the topology update in cases where we find that
the topology has not actually changed in reality (ie., spurious updates).
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Paul Mackerras <paulus@samba.org>
CC: Nathan Fontenot <nfont@linux.vnet.ibm.com>
CC: Stephen Rothwell <sfr@canb.auug.org.au>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Robert Jennings <rcj@linux.vnet.ibm.com>
CC: Jesse Larrew <jlarrew@linux.vnet.ibm.com>
CC: "Srivatsa S. Bhat" <srivatsa.bhat@linux.vnet.ibm.com>
CC: Alistair Popple <alistair@popple.id.au>
Suggested-by: "Srivatsa S. Bhat" <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Michael Wang <wangyun@linux.vnet.ibm.com>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When building modules with a native le toolchain the linker will
generate R_PPC64_TOCSAVE relocations when it's safe to omit saving r2 on
a plt call. This isn't helpful in the conext of a kernel module and the
kernel will fail to load those modules with an error like:
nf_conntrack: Unknown ADD relocation: 109
This patch tells the linker to avoid createing R_PPC64_TOCSAVE
relocations allowing modules to load.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Here rcu_assign_pointer() is ensuring that the
initialization of a structure is carried out before storing a pointer
to that structure.
So, rcu_assign_pointer(p, NULL) can always safely be converted to
RCU_INIT_POINTER(p, NULL).
Signed-off-by: Monam Agarwal <monamagarwal123@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
next-20140324 currently fails compiling celleb_defconfig with:
arch/powerpc/include/asm/opal.h:894:42: error: 'struct notifier_block' declared inside parameter list [-Werror]
arch/powerpc/include/asm/opal.h:894:42: error: its scope is only this definition or declaration, which is probably not what you want [-Werror]
arch/powerpc/include/asm/opal.h:896:14: error: 'struct notifier_block' declared inside parameter list [-Werror]
This is due to a missing include which is added here.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Just about all of these have been converted to __func__,
so convert the last uses.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Recent CPUs support quad word load and store instructions. Add
support to the alignment handler for them.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This call will not be understood by OPAL, and cause it to add an error
to it's log. Among other things, this is useful for testing the
behaviour of the log as it fills up.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
OPAL provides an in-memory circular buffer containing a message log
populated with various runtime messages produced by the firmware.
Provide a sysfs interface /sys/firmware/opal/msglog for userspace to
view the messages.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently we wrongly allocate mc_recoverable_range buffer (to hold
recoverable ranges) based on size of the property "mcheck-recoverable-ranges".
This results in allocating less memory to hold available recoverable range
entries from /proc/device-tree/ibm,opal/mcheck-recoverable-ranges.
This patch fixes this issue by allocating mc_recoverable_range buffer based
on number of entries of recoverable ranges instead of device property size.
Without this change we end up allocating less memory and run into memory
corruption issue.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In:
commit 742415d6b6
Author: Michael Neuling <mikey@neuling.org>
powerpc: Turn syscall handler into macros
We converted the syscall entry code onto macros, but in doing this we
introduced some cruft that's never run and should never have been added.
This removes that code.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We need to handle numa pte via the slow path
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
One OPAL call and one device tree property needed byte swapping.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull nfsd updates from Bruce Fields:
"Highlights:
- server-side nfs/rdma fixes from Jeff Layton and Tom Tucker
- xdr fixes (a larger xdr rewrite has been posted but I decided it
would be better to queue it up for 3.16).
- miscellaneous fixes and cleanup from all over (thanks especially to
Kinglong Mee)"
* 'for-3.15' of git://linux-nfs.org/~bfields/linux: (36 commits)
nfsd4: don't create unnecessary mask acl
nfsd: revert v2 half of "nfsd: don't return high mode bits"
nfsd4: fix memory leak in nfsd4_encode_fattr()
nfsd: check passed socket's net matches NFSd superblock's one
SUNRPC: Clear xpt_bc_xprt if xs_setup_bc_tcp failed
NFSD/SUNRPC: Check rpc_xprt out of xs_setup_bc_tcp
SUNRPC: New helper for creating client with rpc_xprt
NFSD: Free backchannel xprt in bc_destroy
NFSD: Clear wcc data between compound ops
nfsd: Don't return NFS4ERR_STALE_STATEID for NFSv4.1+
nfsd4: fix nfs4err_resource in 4.1 case
nfsd4: fix setclientid encode size
nfsd4: remove redundant check from nfsd4_check_resp_size
nfsd4: use more generous NFS4_ACL_MAX
nfsd4: minor nfsd4_replay_cache_entry cleanup
nfsd4: nfsd4_replay_cache_entry should be static
nfsd4: update comments with obsolete function name
rpc: Allow xdr_buf_subsegment to operate in-place
NFSD: Using free_conn free connection
SUNRPC: fix memory leak of peer addresses in XPRT
...
Merge a few more patches from Andrew Morton:
"A few leftovers"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
fs/ncpfs/dir.c: fix indenting in ncp_lookup()
ncpfs/inode.c: fix mismatch printk formats and arguments
ncpfs: remove now unused PRINTK macro
ncpfs: convert PPRINTK to ncp_vdbg
ncpfs: convert DPRINTK/DDPRINTK to ncp_dbg
ncpfs: Add pr_fmt and convert printks to pr_<level>
arch/x86/mm/kmemcheck/kmemcheck.c: use kstrtoint() instead of sscanf()
lib/percpu_counter.c: fix bad percpu counter state during suspend
autofs4: check dev ioctl size before allocating
mm: vmscan: do not swap anon pages just because free+file is low
My static checker suggests adding curly braces here. Probably that was
the intent, but actually the code works the same either way. I've just
changed the indenting and left the code as-is.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Petr Vandrovec <petr@vandrovec.name>
Acked-by: Dave Chiluk <chiluk@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Conversions to ncp_dbg showed some format/argument mismatches so fix
them.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Petr Vandrovec <petr@vandrovec.name>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Uses are gone, remove the macro.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Petr Vandrovec <petr@vandrovec.name>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use a more current logging style.
Convert the paranoia debug statement to vdbg.
Remove the embedded function names as dynamic_debug can do that.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Petr Vandrovec <petr@vandrovec.name>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use a more current logging style and enable use of dynamic debugging.
Remove embedded function names, dynamic debug can add this instead.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Petr Vandrovec <petr@vandrovec.name>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert to a more current logging style.
Add pr_fmt to prefix with "ncpfs: ".
Remove the embedded function names and use "%s: ", __func__
Some previously unprefixed messages now have "ncpfs: "
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Petr Vandrovec <petr@vandrovec.name>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kmemcheck should use the preferred interface for parsing command line
arguments, kstrto*(), rather than sscanf() itself. Use it
appropriately.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Vegard Nossum <vegardno@ifi.uio.no>
Acked-by: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I got a bug report yesterday from Laszlo Ersek in which he states that
his kvm instance fails to suspend. Laszlo bisected it down to this
commit 1cf7e9c68f ("virtio_blk: blk-mq support") where virtio-blk is
converted to use the blk-mq infrastructure.
After digging a bit, it became clear that the issue was with the queue
drain. blk-mq tracks queue usage in a percpu counter, which is
incremented on request alloc and decremented when the request is freed.
The initial hunt was for an inconsistency in blk-mq, but everything
seemed fine. In fact, the counter only returned crazy values when
suspend was in progress.
When a CPU is unplugged, the percpu counters merges that CPU state with
the general state. blk-mq takes care to register a hotcpu notifier with
the appropriate priority, so we know it runs after the percpu counter
notifier. However, the percpu counter notifier only merges the state
when the CPU is fully gone. This leaves a state transition where the
CPU going away is no longer in the online mask, yet it still holds
private values. This means that in this state, percpu_counter_sum()
returns invalid results, and the suspend then hangs waiting for
abs(dead-cpu-value) requests to complete which of course will never
happen.
Fix this by clearing the state earlier, so we never have a case where
the CPU isn't in online mask but still holds private state. This bug
has been there since forever, I guess we don't have a lot of users where
percpu counters needs to be reliable during the suspend cycle.
Signed-off-by: Jens Axboe <axboe@fb.com>
Reported-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There wasn't any check of the size passed from userspace before trying
to allocate the memory required.
This meant that userspace might request more space than allowed,
triggering an OOM.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Page reclaim force-scans / swaps anonymous pages when file cache drops
below the high watermark of a zone in order to prevent what little cache
remains from thrashing.
However, on bigger machines the high watermark value can be quite large
and when the workload is dominated by a static anonymous/shmem set, the
file set might just be a small window of used-once cache. In such
situations, the VM starts swapping heavily when instead it should be
recycling the no longer used cache.
This is a longer-standing problem, but it's more likely to trigger after
commit 81c0a2bb51 ("mm: page_alloc: fair zone allocator policy")
because file pages can no longer accumulate in a single zone and are
dispersed into smaller fractions among the available zones.
To resolve this, do not force scan anon when file pages are low but
instead rely on the scan/rotation ratios to make the right prediction.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Rafael Aquini <aquini@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: Suleiman Souhlal <suleiman@google.com>
Cc: <stable@kernel.org> [3.12+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull more networking updates from David Miller:
1) If a VXLAN interface is created with no groups, we can crash on
reception of packets. Fix from Mike Rapoport.
2) Missing includes in CPTS driver, from Alexei Starovoitov.
3) Fix string validations in isdnloop driver, from YOSHIFUJI Hideaki
and Dan Carpenter.
4) Missing irq.h include in bnxw2x, enic, and qlcnic drivers. From
Josh Boyer.
5) AF_PACKET transmit doesn't statistically count TX drops, from Daniel
Borkmann.
6) Byte-Queue-Limit enabled drivers aren't handled properly in
AF_PACKET transmit path, also from Daniel Borkmann.
Same problem exists in pktgen, and Daniel fixed it there too.
7) Fix resource leaks in driver probe error paths of new sxgbe driver,
from Francois Romieu.
8) Truesize of SKBs can gradually get more and more corrupted in NAPI
packet recycling path, fix from Eric Dumazet.
9) Fix uniprocessor netfilter build, from Florian Westphal. In the
longer term we should perhaps try to find a way for ARRAY_SIZE() to
work even with zero sized array elements.
10) Fix crash in netfilter conntrack extensions due to mis-estimation of
required extension space. From Andrey Vagin.
11) Since we commit table rule updates before trying to copy the
counters back to userspace (it's the last action we perform), we
really can't signal the user copy with an error as we are beyond the
point from which we can unwind everything. This causes all kinds of
use after free crashes and other mysterious behavior.
From Thomas Graf.
12) Restore previous behvaior of div/mod by zero in BPF filter
processing. From Daniel Borkmann.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (38 commits)
net: sctp: wake up all assocs if sndbuf policy is per socket
isdnloop: several buffer overflows
netdev: remove potentially harmful checks
pktgen: fix xmit test for BQL enabled devices
net/at91_ether: avoid NULL pointer dereference
tipc: Let tipc_release() return 0
at86rf230: fix MAX_CSMA_RETRIES parameter
mac802154: fix duplicate #include headers
sxgbe: fix duplicate #include headers
net: filter: be more defensive on div/mod by X==0
netfilter: Can't fail and free after table replacement
xen-netback: Trivial format string fix
net: bcmgenet: Remove unnecessary version.h inclusion
net: smc911x: Remove unused local variable
bonding: Inactive slaves should keep inactive flag's value
netfilter: nf_tables: fix wrong format in request_module()
netfilter: nf_tables: set names cannot be larger than 15 bytes
netfilter: nf_conntrack: reserve two bytes for nf_ct_ext->len
netfilter: Add {ipt,ip6t}_osf aliases for xt_osf
netfilter: x_tables: allow to use cgroup match for LOCAL_IN nf hooks
...
Here are some more staging patches for 3.15-rc1. They include a
late-submission of a wireless driver that a bunch of people seem to have
the hardware for now. As it's stand-alone, it should be fine (now
passes the 0-day random build bot tests.) There are also some fixes for
the unisys drivers, as they were causing havoc on a number of different
machines. To resolve all of those issues, we just mark the driver as
BROKEN now, and we can fix it up "properly" over time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlNEO1sACgkQMUfUDdst+ymMegCgy/ZpC010cymW2ZYgDxqjEEss
3xUAoLA0Psv1z59hZv4EwrfStxzTiYAQ
=waW7
-----END PGP SIGNATURE-----
Merge tag 'staging-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull more staging patches from Greg KH:
"Here are some more staging patches for 3.15-rc1.
They include a late-submission of a wireless driver that a bunch of
people seem to have the hardware for now. As it's stand-alone, it
should be fine (now passes the 0-day random build bot tests).
There are also some fixes for the unisys drivers, as they were causing
havoc on a number of different machines. To resolve all of those
issues, we just mark the driver as BROKEN now, and we can fix it up
"properly" over time"
* tag 'staging-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: rtl8723au: The 8723 only has two paths
Staging: unisys: mark drivers as BROKEN
Staging: unisys: verify that a control channel exists
staging: unisys: Add missing close parentheses in filexfer.c
staging: r8723au: Fix build problem when RFKILL is not selected
staging: r8723au: Fix randconfig build errors
staging: r8723au: Turn on build of new driver
staging: r8723au: Additional source patches
staging: r8723au: Add source files for new driver - part 4
staging: r8723au: Add source files for new driver - part 3
staging: r8723au: Add source files for new driver - part 2
staging: r8723au: Add source files for new driver - part 1
- Additional cache flushing during boot (needed in the presence of
external caches or under virtualisation)
- DMA range invalidation fix for non cache line aligned buffers
- Build failure fix with !COMPAT
- Kconfig update for STRICT_DEVMEM
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)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=mDkd
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull second set of arm64 updates from Catalin Marinas:
"A second pull request for this merging window, mainly with fixes and
docs clarification:
- Documentation clarification on CPU topology and booting
requirements
- Additional cache flushing during boot (needed in the presence of
external caches or under virtualisation)
- DMA range invalidation fix for non cache line aligned buffers
- Build failure fix with !COMPAT
- Kconfig update for STRICT_DEVMEM"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Fix DMA range invalidation for cache line unaligned buffers
arm64: Add missing Kconfig for CONFIG_STRICT_DEVMEM
arm64: fix !CONFIG_COMPAT build failures
Revert "arm64: virt: ensure visibility of __boot_cpu_mode"
arm64: Relax the kernel cache requirements for boot
arm64: Update the TCR_EL1 translation granule definitions for 16K pages
ARM: topology: Make it clear that all CPUs need to be described
Pull second set of s390 patches from Martin Schwidefsky:
"The second part of Heikos uaccess rework, the page table walker for
uaccess is now a thing of the past (yay!)
The code change to fix the theoretical TLB flush problem allows us to
add a TLB flush optimization for zEC12, this machine has new
instructions that allow to do CPU local TLB flushes for single pages
and for all pages of a specific address space.
Plus the usual bug fixing and some more cleanup"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/uaccess: rework uaccess code - fix locking issues
s390/mm,tlb: optimize TLB flushing for zEC12
s390/mm,tlb: safeguard against speculative TLB creation
s390/irq: Use defines for external interruption codes
s390/irq: Add defines for external interruption codes
s390/sclp: add timeout for queued requests
kvm/s390: also set guest pages back to stable on kexec/kdump
lcs: Add missing destroy_timer_on_stack()
s390/tape: Add missing destroy_timer_on_stack()
s390/tape: Use del_timer_sync()
s390/3270: fix crash with multiple reset device requests
s390/bitops,atomic: add missing memory barriers
s390/zcrypt: add length check for aligned data to avoid overflow in msg-type 6
SCTP charges chunks for wmem accounting via skb->truesize in
sctp_set_owner_w(), and sctp_wfree() respectively as the
reverse operation. If a sender runs out of wmem, it needs to
wait via sctp_wait_for_sndbuf(), and gets woken up by a call
to __sctp_write_space() mostly via sctp_wfree().
__sctp_write_space() is being called per association. Although
we assign sk->sk_write_space() to sctp_write_space(), which
is then being done per socket, it is only used if send space
is increased per socket option (SO_SNDBUF), as SOCK_USE_WRITE_QUEUE
is set and therefore not invoked in sock_wfree().
Commit 4c3a5bdae2 ("sctp: Don't charge for data in sndbuf
again when transmitting packet") fixed an issue where in case
sctp_packet_transmit() manages to queue up more than sndbuf
bytes, sctp_wait_for_sndbuf() will never be woken up again
unless it is interrupted by a signal. However, a still
remaining issue is that if net.sctp.sndbuf_policy=0, that is
accounting per socket, and one-to-many sockets are in use,
the reclaimed write space from sctp_wfree() is 'unfairly'
handed back on the server to the association that is the lucky
one to be woken up again via __sctp_write_space(), while
the remaining associations are never be woken up again
(unless by a signal).
The effect disappears with net.sctp.sndbuf_policy=1, that
is wmem accounting per association, as it guarantees a fair
share of wmem among associations.
Therefore, if we have reclaimed memory in case of per socket
accounting, wake all related associations to a socket in a
fair manner, that is, traverse the socket association list
starting from the current neighbour of the association and
issue a __sctp_write_space() to everyone until we end up
waking ourselves. This guarantees that no association is
preferred over another and even if more associations are
taken into the one-to-many session, all receivers will get
messages from the server and are not stalled forever on
high load. This setting still leaves the advantage of per
socket accounting in touch as an association can still use
up global limits if unused by others.
Fixes: 4eb701dfc6 ("[SCTP] Fix SCTP sendbuffer accouting.")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Thomas Graf <tgraf@suug.ch>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are three buffer overflows addressed in this patch.
1) In isdnloop_fake_err() we add an 'E' to a 60 character string and
then copy it into a 60 character buffer. I have made the destination
buffer 64 characters and I'm changed the sprintf() to a snprintf().
2) In isdnloop_parse_cmd(), p points to a 6 characters into a 60
character buffer so we have 54 characters. The ->eazlist[] is 11
characters long. I have modified the code to return if the source
buffer is too long.
3) In isdnloop_command() the cbuf[] array was 60 characters long but the
max length of the string then can be up to 79 characters. I made the
cbuf array 80 characters long and changed the sprintf() to snprintf().
I also removed the temporary "dial" buffer and changed it to use "p"
directly.
Unfortunately, we pass the "cbuf" string from isdnloop_command() to
isdnloop_writecmd() which truncates anything over 60 characters to make
it fit in card->omsg[]. (It can accept values up to 255 characters so
long as there is a '\n' character every 60 characters). For now I have
just fixed the memory corruption bug and left the other problems in this
driver alone.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the buffer needing cache invalidation for inbound DMA does start or
end on a cache line aligned address, we need to use the non-destructive
clean&invalidate operation. This issue was introduced by commit
7363590d2c (arm64: Implement coherent DMA API based on swiotlb).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Jon Medhurst (Tixy) <tixy@linaro.org>
Intel SDIO has broken card detect so add a quirk to reflect that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Pull ext3 improvements, cleanups, reiserfs fix from Jan Kara:
"various cleanups for ext2, ext3, udf, isofs, a documentation update
for quota, and a fix of a race in reiserfs readdir implementation"
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
reiserfs: fix race in readdir
ext2: acl: remove unneeded include of linux/capability.h
ext3: explicitly remove inode from orphan list after failed direct io
fs/isofs/inode.c add __init to init_inodecache()
ext3: Speedup WB_SYNC_ALL pass
fs/quota/Kconfig: Update filesystems
ext3: Update outdated comment before ext3_ordered_writepage()
ext3: Update PF_MEMALLOC handling in ext3_write_inode()
ext2/3: use prandom_u32() instead of get_random_bytes()
ext3: remove an unneeded check in ext3_new_blocks()
ext3: remove unneeded check in ext3_ordered_writepage()
fs: Mark function as static in ext3/xattr_security.c
fs: Mark function as static in ext3/dir.c
fs: Mark function as static in ext2/xattr_security.c
ext3: Add __init macro to init_inodecache
ext2: Add __init macro to init_inodecache
udf: Add __init macro to init_inodecache
fs: udf: parse_options: blocksize check
Pull kbuild changes from Michal Marek:
- cleanups in the main Makefiles and Documentation/DocBook/Makefile
- make O=... directory is automatically created if needed
- mrproper/distclean removes the old include/linux/version.h to make
life easier when bisecting across the commit that moved the version.h
file
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kbuild: docbook: fix the include error when executing "make help"
kbuild: create a build directory automatically for out-of-tree build
kbuild: remove redundant '.*.cmd' pattern from make distclean
kbuild: move "quote" to Kbuild.include to be consistent
kbuild: docbook: use $(obj) and $(src) rather than specific path
kbuild: unconditionally clobber include/linux/version.h on distclean
kbuild: docbook: specify KERNELDOC dependency correctly
kbuild: docbook: include cmd files more simply
kbuild: specify build_docproc as a phony target
* Support for external initrd from Noam
* Fix broken serial console in nsimosci Virtual Platform
* Reuse of ENTRY/END assembler macros across hand asm code
* Other minor fixes here and there
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=dmgU
-----END PGP SIGNATURE-----
Merge tag 'arc-v3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC changes from Vineet Gupta:
- Support for external initrd from Noam
- Fix broken serial console in nsimosci Virtual Platform
- Reuse of ENTRY/END assembler macros across hand asm code
- Other minor fixes here and there
* tag 'arc-v3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: [nsimosci] Unbork console
ARC: [nsimosci] Change .dts to use generic 8250 UART
ARC: [SMP] General Fixes
ARC: Remove unused DT template file
ARC: [clockevent] simplify timer ISR
ARC: [clockevent] can't be SoC specific
ARC: Remove ARC_HAS_COH_RTSC
ARC: switch to generic ENTRY/END assembler annotations
ARC: support external initrd
ARC: add uImage to .gitignore
ARC: [arcfpga] Fix __initconst data const-correctness
Loading cursors to the LCD controller's SRAM can be corrupted when the
configured pixel clock is relatively slow. This seems to be caused
when we write back-to-back to the SRAM registers.
There doesn't appear to be any status register we can read to check
when an access has completed.
Inserting a dummy read between the writes appears to fix the problem.
Cc: <stable@vger.kernel.org> # 3.13
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The merge of irq-core-for-linus branch broke it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iQEcBAABAgAGBQJTQqWqAAoJEFxbo/MsZsTRCTAH/j9JC0q5OuCPoZlvhHgrOsaI
Z8gZj9MsU5zBiGrBrp96ULHVBxe/PWSCFhPWvxykhS5d/tgpeg0l2B2n7KrsgtrE
YSepxlyGzGK5UUYZmCCiE4fjZA2GrtHtz4tET3lu5lyHWCNgHuApmGDsoIJ+PH13
wCokIJcBpVu+V7nsxSifguud1R9ZEA7gTwp1q5omSerrqNLPPYuxlwSRTDIS4pEl
5mhP5C9ej+u7Dx7h4uRpk7p2YMQy1pnPtJIq3TBH2B/l/u96b+gyXQlLhf289LSP
RwiDhurZprLZmaM8W1qrQwqsoiPY/uQQFObp0icvrarK7SfYtiot+guK3oRn1NI=
=1P/a
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.15-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen build fix from David Vrabel:
"Fix arm build of drivers/xen/events/
The merge of irq-core-for-linus branch broke it"
* tag 'stable/for-linus-3.15-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
Xen: do hv callback accounting only on x86
Merge second patch-bomb from Andrew Morton:
- the rest of MM
- zram updates
- zswap updates
- exit
- procfs
- exec
- wait
- crash dump
- lib/idr
- rapidio
- adfs, affs, bfs, ufs
- cris
- Kconfig things
- initramfs
- small amount of IPC material
- percpu enhancements
- early ioremap support
- various other misc things
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (156 commits)
MAINTAINERS: update Intel C600 SAS driver maintainers
fs/ufs: remove unused ufs_super_block_third pointer
fs/ufs: remove unused ufs_super_block_second pointer
fs/ufs: remove unused ufs_super_block_first pointer
fs/ufs/super.c: add __init to init_inodecache()
doc/kernel-parameters.txt: add early_ioremap_debug
arm64: add early_ioremap support
arm64: initialize pgprot info earlier in boot
x86: use generic early_ioremap
mm: create generic early_ioremap() support
x86/mm: sparse warning fix for early_memremap
lglock: map to spinlock when !CONFIG_SMP
percpu: add preemption checks to __this_cpu ops
vmstat: use raw_cpu_ops to avoid false positives on preemption checks
slub: use raw_cpu_inc for incrementing statistics
net: replace __this_cpu_inc in route.c with raw_cpu_inc
modules: use raw_cpu_write for initialization of per cpu refcount.
mm: use raw_cpu ops for determining current NUMA node
percpu: add raw_cpu_ops
slub: fix leak of 'name' in sysfs_slab_add
...
Pointer 'usb3' to struct ufs_super_block_third acquired via
ubh_get_usb_third() is never used in function
ufs_read_cylinder_structures(). Thus remove it.
Detected by Coverity: CID 139939.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Cc: Evgeniy Dushistov <dushistov@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pointer 'usb2' to struct ufs_super_block_second acquired via
ubh_get_usb_second() is never used in function ufs_statfs(). Thus
remove it.
Detected by Coverity: CID 139940.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Cc: Evgeniy Dushistov <dushistov@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
