While the driver is probing the adapter, an error may occur before the
netdev structure is allocated and attached to pci_dev. In this case,
not only netdev isn't available, but the tg3 private structure is also
not available as it is just math from the NULL pointer, so dereferences
must be skipped.
The following trace is seen when the error is triggered:
[1.402247] Unable to handle kernel paging request for data at address 0x00001a99
[1.402410] Faulting instruction address: 0xc0000000007e33f8
[1.402450] Oops: Kernel access of bad area, sig: 11 [#1]
[1.402481] SMP NR_CPUS=2048 NUMA PowerNV
[1.402513] Modules linked in:
[1.402545] CPU: 0 PID: 651 Comm: eehd Not tainted 4.4.0-36-generic #55-Ubuntu
[1.402591] task: c000001fe4e42a20 ti: c000001fe4e88000 task.ti: c000001fe4e88000
[1.402742] NIP: c0000000007e33f8 LR: c0000000007e3164 CTR: c000000000595ea0
[1.402787] REGS: c000001fe4e8b790 TRAP: 0300 Not tainted (4.4.0-36-generic)
[1.402832] MSR: 9000000100009033 <SF,HV,EE,ME,IR,DR,RI,LE> CR: 28000422 XER: 20000000
[1.403058] CFAR: c000000000008468 DAR: 0000000000001a99 DSISR: 42000000 SOFTE: 1
GPR00: c0000000007e3164 c000001fe4e8ba10 c0000000015c5e00 0000000000000000
GPR04: 0000000000000001 0000000000000000 0000000000000039 0000000000000299
GPR08: 0000000000000000 0000000000000001 c000001fe4e88000 0000000000000006
GPR12: 0000000000000000 c00000000fb40000 c0000000000e6558 c000003ca1bffd00
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20: 0000000000000000 0000000000000000 0000000000000000 c000000000d52768
GPR24: c000000000d52740 0000000000000100 c000003ca1b52000 0000000000000002
GPR28: 0000000000000900 0000000000000000 c00000000152a0c0 c000003ca1b52000
[1.404226] NIP [c0000000007e33f8] tg3_io_error_detected+0x308/0x340
[1.404265] LR [c0000000007e3164] tg3_io_error_detected+0x74/0x340
This patch avoids the NULL pointer dereference by moving the access after
the netdev NULL pointer check on tg3_io_error_detected(). Also, we add a
check for netdev being NULL on tg3_io_resume() [suggested by Michael Chan].
Fixes: 0486a063b1 ("tg3: prevent ifup/ifdown during PCI error recovery")
Fixes: dfc8f37031 ("net/tg3: Release IRQs on permanent error")
Tested-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Milton Miller <miltonm@us.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 62469c7600 ("net: ethernet: bcmgenet: use phydev
from struct net_device") because it causes GENETv1/2/3 adapters to
expose the following behavior after an ifconfig down/up sequence:
PING fainelli-linux (10.112.156.244): 56 data bytes
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.352 ms
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.472 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.496 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.517 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.536 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.557 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=752.448 ms (DUP!)
This was previously fixed by commit 5dbebbb44a ("net: bcmgenet:
Software reset EPHY after power on") but the commit we are reverting was
essentially making this previous commit void, here is why.
Without commit 62469c7600 we would have the following scenario after
an ifconfig down then up sequence:
- bcmgenet_open() calls bcmgenet_power_up() to make sure the PHY is
initialized *before* we get to initialize the UniMAC, this is
critical to ensure the PHY is in a correct state, priv->phydev is
valid, this code executes fine
- second time from bcmgenet_mii_probe(), through the normal
phy_init_hw() call (which arguably could be optimized out)
Everything is fine in that case. With commit 62469c7600, we would have
the following scenario to happen after an ifconfig down then up
sequence:
- bcmgenet_close() calls phy_disonnect() which makes dev->phydev become
NULL
- when bcmgenet_open() executes again and calls bcmgenet_mii_reset() from
bcmgenet_power_up() to initialize the internal PHY, the NULL check
becomes true, so we do not reset the PHY, yet we keep going on and
initialize the UniMAC, causing MAC activity to occur
- we call bcmgenet_mii_reset() from bcmgenet_mii_probe(), but this is
too late, the PHY is botched, and causes the above bogus pings/packets
transmission/reception to occur
Reported-by: Jaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FEC receive accelerator (RACC) supports shifting the data payload of
received packets by 16-bits, which aligns the payload (IP header) on a
4-byte boundary, which is, if not required, at least strongly suggested
by the Linux networking layer.
Without this patch, a huge number of alignment faults will be taken by the
IP stack, as seen in /proc/cpu/alignment:
~/$ cat /proc/cpu/alignment
User: 0
System: 72645 (inet_gro_receive+0x104/0x27c)
Skipped: 0
Half: 0
Word: 0
DWord: 0
Multi: 72645
User faults: 3 (fixup+warn)
This patch was suggested by Andrew Lunn in this message to linux-netdev:
http://marc.info/?l=linux-arm-kernel&m=147465452108384&w=2
and adapted from a patch by Russell King from 2014:
http://git.arm.linux.org.uk/cgit/linux-arm.git/commit/?id=70d8a8a
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the i.MX27 reference manual, this SoC does not have support
for the receive accelerator (RACC) register at offset 0x1C4.
http://cache.nxp.com/files/32bit/doc/ref_manual/MCIMX27RM.pdf
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the i.MX25 reference manual, this SoC does not have support
for the receive accelerator (RACC) register at offset 0x1C4.
http://www.nxp.com/files/dsp/doc/ref_manual/IMX25RM.pdf
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A timer was used to restart after the bus-off state, leading to a
relatively large can_restart() executed in an interrupt context,
which in turn sets up pinctrl. When this happens during system boot,
there is a high probability of grabbing the pinctrl_list_mutex,
which is locked already by the probe() of other device, making the
kernel suspect a deadlock condition [1].
To resolve this issue, the restart_timer is replaced by a delayed
work.
[1] https://github.com/victronenergy/venus/issues/24
Signed-off-by: Sergei Miroshnichenko <sergeimir@emcraft.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
-----BEGIN PGP SIGNATURE-----
iQEcBAABCgAGBQJX4kYAAAoJED07qiWsqSVqzoYIAKEkRhTIgrHr14kJhFOTfMF2
jftbRrOXgUhfaVTrK8EdqCZ6RWUsquHg/l6n4N5uMu2mPE9z2xaql6TuoeS0LLtu
l7a6sSgo+qvAY8nwn8ObAI0+528kIkPHY8bM3QCx0LhjVrBM0JtLWgPRudsQoUko
yctxxpXY18Jo58SCn7k27cg+3V2j+ZDYd0hAOvQUPbI5Cw8kGRUHkUOqUtqn3oD3
3eSlRX64Or25V2q0zrM1OqFcmT/W6Os+Icne4DWomU0uy4e/YV8DyTj2qV52S4id
7k7qyv/ITVPdHeg/xxdEVgc6AaD1HsIym1IZF6JsdUFRPf6r/Rt+hVAlPYbDdtg=
=zagb
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-4.8-20160921' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2016-09-21
this is another pull request of one patch for the upcoming linux-4.8 release.
Marek Vasut fixes the CAN-FD bit rate switch in the ifi driver by configuring
the transmitter delay.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans devlink resources by calling devlink_port_unregister()
to avoid the following issues:
- Kernel panic when triggering reset flow.
- Memory leak due to unfreed resources in mlx4_init_port_info().
Fixes: 09d4d087cd ("mlx4: Implement devlink interface")
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iwlwifi
* fix to prevent firmware crash when sending off-channel frames
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJX4QrCAAoJEG4XJFUm622beaQIAJBf9BWZ0ZYu7qz0C5VXjOh2
+mDPz6eI2uHKFtliyyMxqxrDZf2Ik+xlTnDudtOqhOglx6bO0f1q3OSqWZdZ/tg2
eCWN/Yt8i3lVlHaa5pQprkqaQ7lFO4KUKmN4augZk1AXlCH6H2n7zfX4N2MoKnxQ
1nKDTUWgjLPwdrvVvLLdKj/FWKRObxpDs21pdPRyeyW2u+K257z9mx0Zf5NxodZU
2aIrPiiNvsTIT2BVf7FCQTZvyMPWh3JbkaVe15beuwXGiJYY0EYT89oc7zW80tLY
0wRpUpELCbmJtducjkbsh91rnhp495HXQX71p+EhWn9GK2XR+TUCUTEmv+w0HVY=
=6EUu
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2016-09-20' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.8
iwlwifi
* fix to prevent firmware crash when sending off-channel frames
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Configure the transmitter delay register at +0x1c to correctly handle
the CAN FD bitrate switch (BRS). This moves the SSP (secondary sample
point) to a proper offset, so that the TDC mechanism works and won't
generate error frames on the CAN link.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Disable ALDPS and EEE to avoid the possible failure when setting the PHY.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the PHY relative settings together to hw_phy_cfg().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move enabling PHY to init(), otherwise some other settings may fail.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the following functions forward.
r8152_mmd_indirect()
r8152_mmd_read()
r8152_mmd_write()
r8152_eee_en()
r8152b_enable_eee()
r8153_eee_en()
r8153_enable_eee()
r8152b_enable_fc()
r8153_aldps_en()
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were missing check for 25G and 100G while checking port speed,
which lead to less number of queues getting allocated for 25G & 100G
adapters and leading to low throughput. Adding the missing check for
both NIC and vNIC driver.
Also fixes port advertisement for 25G and 100G in ethtool output.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABCgAGBQJX3/GcAAoJED07qiWsqSVq9PgH/jucrHh2H7IAnJi6ZasZmu1t
+beOkzg954rJfz2cGulhpNBAl9xJYRhPuJ+Jw5JhDEPXVisgeRVm6lT+8YJaCsWL
utTotzyRYI3HUrXIl6V2rjn1ms7TAlZsHrAGPj1ufJKEZg8/SF5C15NuY9YTlh4d
JZT0V13Yxj0CV3d2jqZshFXrF+CiAsGyQF1aGA9Wo2xQeZIt2vY/1DfNtC9eXlXW
+t7tBCgLka7cwTBC513BKjl9fGwzYO0eYU993N9+Ijir6HLM9N3igZwxjH1hEl/S
ow6n5T1O89JEnghSN5Xq+2ThkkXR7zZwi+6l74eFICkIwHK/pekZ8dPr9Ct9ZZ0=
=JcjG
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-4.8-20160919' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2016-09-19
this is a pull request of one patch for the upcoming linux-4.8 release.
The patch by Fabio Estevam fixes the pm handling in the flexcan driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit fe56b9e6a8 ("qed: Add module with basic common support")
has introduced a stack corruption during probe, where filling a
local struct with data to be sent to management firmware is incorrectly
filled; The data is written outside of the struct and corrupts
the stack.
Changes from v1:
----------------
- Correct the value written [Caught by David Laight]
Fixes: fe56b9e6a8 ("qed: Add module with basic common support")
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
E-switch mode changes involve creating HW tables, potentially allocating
netdevices, etc, and things can fail. Add an attempt to rollback to the
existing mode when changing to the new mode fails. Only if rollback fails,
getting proper SRIOV functionality requires module unload or sriov
disablement/enablement.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enablement of the SRIOV e-switch in certain mode (switchdev or legacy)
fails, we must set the mode to none. Otherwise, we'll run into double free
based crashes when further attempting to deal with the e-switch (such
as when disabling sriov or unloading the driver).
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FW command output length should be only the length of struct
mlx5_cmd_fc_bulk out field. Failing to do so will cause the memcpy
call which is invoked later in the driver to write over wrong memory
address and corrupt kernel memory which results in random crashes.
This bug was found using the kernel address sanitizer (kasan).
Fixes: a351a1b03b ('net/mlx5: Introduce bulk reading of flow counters')
Signed-off-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On a imx6ul-pico board the following error is seen during system suspend:
dpm_run_callback(): platform_pm_resume+0x0/0x54 returns -110
PM: Device 2090000.flexcan failed to resume: error -110
The reason for this suspend error is because when the CAN interface is not
active the clocks are disabled and then flexcan_chip_enable() will
always fail due to a timeout error.
In order to fix this issue, only call flexcan_chip_enable/disable()
when the CAN interface is active.
Based on a patch from Dong Aisheng in the NXP kernel.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
MAC devices use the RWKPKTEN and MGKPKTEN bits of the PMT Control/Status
register to generate power management events.
So this patch is to properly set the RWKPKTEN [BIT(2)] inside the
PMT register (needed in case of global unicast).
Reported-by: Aditi SHARMA <aditi-hed.sharma@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6e7333d "net: add rx_nohandler stat counter" added the new entry
rx_nohandler into struct rtnl_link_stats64. Unfortunately the bna
driver foolishly depends on the structure. It uses part of it for
ethtool statistics and it's not bad but the driver assumes its size
is constant as it defines string for each existing entry. The problem
occurs when the structure is extended because you need to modify bna
driver as well. If not any attempt to retrieve ethtool statistics results
in crash in bnad_get_strings().
The patch changes BNAD_ETHTOOL_STATS_NUM so it counts real number of
strings in the array and also removes rtnl_link_stats64 entries that
are not used in output and are always zero.
Fixes: 6e7333d "net: add rx_nohandler stat counter"
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ba5ca784 "bna: check for dma mapping errors" added besides other
things a statistic that counts number of DMA buffer mapping failures
per each Rx queue. This counter is not included in ethtool stats output.
Fixes: ba5ca784 "bna: check for dma mapping errors"
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error during netback_probe() (e.g. an entry missing on the
xenstore) netback_remove() is called on the new device, which will set
the device backend state to XenbusStateClosed by calling
set_backend_state(). However, the backend state wasn't initialized by
netback_probe() at this point, which will cause and invalid transaction
and set_backend_state() to BUG().
Initialize the backend state at the beginning of netback_probe() to
XenbusStateInitialising, and create two new valid state transitions on
set_backend_state(), from XenbusStateInitialising to XenbusStateClosed,
and from XenbusStateInitialising to XenbusStateInitWait.
Signed-off-by: Filipe Manco <filipe.manco@neclab.eu>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 73725d9dfd ("nfp: allocate ring SW structs dynamically")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
for preventing race conditions within ioctl calls.
Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add realization for mac address set and remove dummy callback.
Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device table is required to load modules based on
modaliases. After adding MODULE_DEVICE_TABLE, below entries
for example will be added to modules.alias:
alias of:N*T*Cmediatek,mt7623-ethC* mtk_eth_soc
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an error occurs in mlx4_init_eq_table the index used in the
err_out_unmap label is one too big which results in a panic in
mlx4_free_eq. This patch fixes the index in the error path.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Off-channel action frames (such as ANQP frames) must be sent either on
the AUX queue or on the offchannel queue, otherwise the firmware will
cause a SYSASSERT.
In the current implementation, the queue to be used is correctly set in
the original skb, but this is done after it is copied. Thus the copy
remains with the original, incorrect queue.
Fix this by setting the queue in the original skb before copying it.
Fixes: commit 5c08b0f502 ("iwlwifi: mvm: don't override the rate with the AMSDU len")
Cc: stable@vger.kernel.org # v4.6+
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If 'IS_ERR(pdata->clk)' is true, then 'clk_disable_unprepare(pdata->clk)'
will do nothing.
It is likely that 'if (!IS_ERR(pdata->clk))' was expected here.
In fact, the test can even be removed because 'clk_disable_unprepare'
already handles such cases.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
When system enters into kdump kernel because of kernel panic, it won't
shutdown devices. On-flight DMA will continue transferring data until
device driver initializes. All devices are supposed to reset during
driver initialization. And this property is used to fix the kdump
failure in system with intel iommu. Other systems with hardware iommu
should be similar. Please check commit 091d42e ("iommu/vt-d: Copy
translation tables from old kernel") and those commits around.
But bnx2 driver doesn't reset device during driver initialization. The
device resetting is deferred to net device up stage. This will cause
hardware iommu handling failure on bnx2 device. And its resetting relies
on firmware. So in this patch move the firmware requesting code to earlier
bnx2_init_one(), then next call bnx2_reset_chip to reset device.
Signed-off-by: Baoquan He <bhe@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When port is down, tx drop counter update is not needed.
Updating the counter in this case can cause a kernel
panic as when the port is down, ring can be NULL.
Fixes: 63a664b7e9 ("net/mlx4_en: fix tx_dropped bug")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a capability check before enabling DCBX.
In addition, it re-organizes the relevant data structures,
and fixes a typo in a define.
Fixes: af7d518526 ("net/mlx4_en: Add DCB PFC support through CEE netlink commands")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_en_dcbnl_set_state() returns u8, the return value from
mlx4_en_setup_tc() could be negative in case of failure, so fix that.
Fixes: af7d518526 ("net/mlx4_en: Add DCB PFC support through CEE netlink commands")
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_en_dcbnl_set_all() returns u8, so return value can't be negative in
case of failure.
Fixes: af7d518526 ("net/mlx4_en: Add DCB PFC support through CEE netlink commands")
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to a mistake in the hardware manual, the FWSLC and POST1-4 registers
were not documented and left out of the driver for RZ/A making the CAM
feature non-operational.
Additionally, when the offset values for POST1-4 are left blank, the driver
attempts to set them using an offset of 0xFFFF which can cause a memory
corruption or panic.
This patch fixes the panic and properly enables CAM.
Reported-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mdio-xgene driver is only useful on X-Gene SoC.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Iyappan Subramanian <isubramanian@apm.com>
Cc: David S. Miller <davem@davemloft.net>
Acked-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iwlwifi
* fix P2P dump trigger
* prevent a potential null dereference in iwlmvm
* prevent an uninitialized value from being returned in iwlmvm
* advertise support for channel width change in AP mode
ath10k
* fix racy rx status retrieval from htt context
* QCA9887 support is not experimental anymore, remove the warning message
ath9k
* fix regression with led GPIOs
* fix AR5416 GPIO access warning
brcmfmac
* avoid potential stack overflow in brcmf_cfg80211_start_ap()
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJX0UZGAAoJEG4XJFUm622bNrQH/1x1A5go1O0WT9LFz7xgowY9
LtcpDcyDsz0h+dn1d9VuncTuO8mSREP/zxcDyibhiwnrVXR00QM0F9VgPSlUxASH
PwM06NZACblCk/mqSzI79BJ8kNBlwIhcr6OXpwzlcvF9JMUIDu/hQCdRPPn0lDRI
XVJHrM7dP2ZB0sVKAbM7+1Q1Bnv5JetPUduu1jOBtk+HiGjOAsejTFOh6AsOqZzZ
ZUTKBJeGkDp3XEVnlgkhJ1Y9xPaMpke/yqAlOPIgP90Ghd2SMJHTHiW6S28P/W1F
FMtTMXbYzzHAHNVSnOMgJyWRm1xD/Y6sVkeyXTD40BgHYXZcB6uHVLnzjR4i4BY=
=teXL
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2016-09-08' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.8
iwlwifi
* fix P2P dump trigger
* prevent a potential null dereference in iwlmvm
* prevent an uninitialized value from being returned in iwlmvm
* advertise support for channel width change in AP mode
ath10k
* fix racy rx status retrieval from htt context
* QCA9887 support is not experimental anymore, remove the warning message
ath9k
* fix regression with led GPIOs
* fix AR5416 GPIO access warning
brcmfmac
* avoid potential stack overflow in brcmf_cfg80211_start_ap()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We move register_netdev() to the end of dwceqos_probe() to close any
races where the netdev callbacks are called before the initialization
has finished.
Reported-by: Pavel Andrianov <andrianov@ispras.ru>
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During port init, we currently set the port's type to Ethernet after
setting its MAC address. However, the hardware documentation states this
should be the other way around.
Align the driver with the hardware documentation and set the port's MAC
address after setting its type.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When neigh_init fails, we have to do proper cleanup including
router_fini call.
Fixes: 6cf3c971dc ("mlxsw: spectrum_router: Add private neigh table")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to pad frames to ETH_ZLEN on RX.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Be more strict about FW versions. Drop support for old
transitional revisions which were never used in production.
Dropping support for FW ABI version 0.0.0.0 is particularly
useful because 0 could just be uninitialized memory.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary version.h includes.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently vlan tagged packets were not parsed correctly
and assumed to be regular IPv4/IPv6 packets.
We should check for 802.1Q/802.1ad tags and update the lro header
accordingly.
This fixes the use case where LRO is on and rxvlan is off
(vlan stripping is off).
Fixes: e586b3b0ba ('net/mlx5: Ethernet Datapath files')
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when reading global PFC statistics we left the counter
iterator out of the equation and we ended up reading the same counter
over and over again.
Instead of reading the counter at index 0 on every iteration we now read
the counter at index (i).
Fixes: e989d5a532 ('net/mlx5e: Expose flow control counters to ethtool')
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
