The I2C-bus to the XPower AXP288 is shared between the Linux kernel and
the SoCs P-Unit. The P-Unit has a semaphore which the kernel must "lock"
before it may use the bus and while the kernel holds the semaphore the CPU
and GPU power-states must not be changed otherwise the system will freeze.
This is a complex process, which is quite expensive. This is all done by
iosf_mbi_block_punit_i2c_access(). To ensure that no unguarded I2C-bus
accesses happen, iosf_mbi_block_punit_i2c_access() gets called by the
I2C-bus-driver for every I2C transfer. Because this is so expensive it
is allowed to call iosf_mbi_block_punit_i2c_access() in a nested
fashion, so that higher-level code which does multiple I2C-transfers can
call it once for a group of transfers, turning the calls done by the
I2C-bus-driver into no-ops.
Userspace power-supply API users typically will read all provided
properties in one go, refreshing the last read values when
power_supply_changed() is called by the driver and/or periodically
(e.g. every 2 minutes).
The reading of all properties in one go causes the P-Unit semaphore
to quickly be taken and released multiple times in a row. Certain
PMIC registers like AXP20X_FG_RES are even used in multiple properties
so they get read multiple times, leading to a P-Unit take + release
each time the register is read.
As already mentioned the taking of the P-Unit semaphore is a quite
expensive operation and it has also been reported that the
"hammering" of the P-Unit semaphore done by the axp288_fuel_gauge
driver can even cause stability issues with the system as a whole.
Switch over to a scheme where the axp288_fuel_gauge driver keeps
a local copy of all the registers which it uses for properties
and make it only refresh its copy of the registers if the values
are older then 1 minute; or when a fuel-gauge interrupt has
triggered since the last read.
This not only reduces the amount of reads, it also makes the code
do all the reads in one go, rather then reading specific registers
based on which property is being queried. This allows calling
iosf_mbi_block_punit_i2c_access() once before doing all the reads,
so that we now only take the P-Unit semaphore once per update.
Tested-by: Andrejus Basovas <cpp@gcc.lt>
Signed-off-by: Andrejus Basovas <cpp@gcc.lt>
Co-developed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Accessing registers on the AXP288 is quite expensive, so we should avoid
doing unnecessary accesses.
The FG_LOW_CAP_REG never changes underneath us, so we only need to read
it once. Devices with an AXP288 do not have user-replace (let alone
hot-swappable) batteries and the only bit we care about in the
PWR_OP_MODE register is the CHRG_STAT_BAT_PRESENT bit, so we can get
away with only reading the PWR_OP_MODE register once too.
Note that the FG_LOW_CAP_REG is not marked volatile in the regmap, so we
were effectively already reading it once. This change makes this explicit,
this is done as preparation of a further patch which moves all remaining
register accesses in fuel_gauge_get_property() out of that function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Directly store the struct device pointer in axp288_fg_info, rather then
storing a pointer to the struct platform_device there and then using
"&info->pdev->dev" everywhere.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The I2C-bus to the XPower AXP288 is shared between the Linux kernel and
the SoCs P-Unit. The P-Unit has a semaphore which the kernel must "lock"
before it may use the bus. This semaphore is automatically taken by the
I2C-bus-driver.
The retry on -EBUSY logic in fuel_gauge_reg_readb() likely was added to
deal with the I2C-bus-drive returning -EBUSY when it failed to take the
semaphore, but this really should never happen. The semaphore code even
has a WARN_ON(ret) to log a kernel backtrace if this does somehow happen,
when this happens something is seriously wrong and the system typically
freezes soon afterwards.
TL;DR: the regmap_read() should never fail with -EBUSY so the retries
are unnecessary.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
When fuel_gauge_reg_readb()/_writeb() fails, report which register we
were trying to read / write when the error happened.
Also reword the message a bit:
- Drop the axp288 prefix, dev_err() already prints this
- Switch from telegram / abbreviated style to a normal sentence, aligning
the message with those from fuel_gauge_read_*bit_word()
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Drop the IRQ mapping messages, because they are really not
interesting at all.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The debugfs code is simply just dumping a bunch of registers, the same
information can also easily be gotten through the regmap debugfs
interface or through the i2cdump utility.
I've not used the debugfs interface once in all these years that I've
been working on the axp288_fuel_gauge driver, so lets just remove it.
Note this also removes the temperature-channels from the list of
IIO ADC channels used by the driver, since these were only used in the
debugfs interface.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The values of various defines used in the driver are not aligned
properly when tabsize is set to 8 (I guess they were created with
a different tabsize).
Properly align the defines to make the code easier to read.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
In the function sc27xx_fgu_probe(), when get irq failed,
platform_get_irq() logs an error message, so remove
redundant message here.
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Deal with deferred probe using dev_err_probe so the error is handled
and avoid logging lots probe defer information like the following:
[ 9.125121] cw2015 4-0062: Failed to register power supply
[ 9.211131] cw2015 4-0062: Failed to register power supply
Fixes: b4c7715c10 ("power: supply: add CellWise cw2015 fuel gauge driver")
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds a driver for PCHG (Peripheral CHarGer). PCHG is a
framework managing power supplies for peripheral devices.
This driver creates a sysfs node for each peripheral charge port:
/sys/class/power_supply/peripheral<n>
where <n> is the index of a charge port.
For example, when a stylus is connected to a NFC/WLC port, the node
returns:
/sys/class/power_supply/peripheral0/
capacity=50
charge_type=Standard
scope=Device
status=Charging
type=Battery
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This file isn't using any AB8500 symbols so drop these includes.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
If we rename the "abx500_chargalg" supply to "ab8500_chargalg"
as it should be named, the existing supplies are supplying that
supply but that was obviously not working since it had the
wrong name.
Now that the dependency kicks in we get a bunch
of NULL references from ab8500_chargalg_external_power_changed()
so check that the workqueue is allocated before we try to
queue work on it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Drop the entire idea with abx500 being abstract and different from ab8500
in the AB8500 charging drivers. This rids the two identical definitions
of a slew of structs in ab8500-bm.h and makes things less confusion and
easier to understand.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The "abx500" name on the charging algorithm stems from the ambition
to produce a series of these analog basebands, re-using the same
charging algorithm driver. No ASICs beside AB8500 and AB8505 were
ever produced so this terminology is confusing. Rename the
algorithm file and symbols to reflect the more narrow scope.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The kernel already has a static inline for linear interpolation
so use that instead of rolling our own.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
kernel.h is being used as a dump for all kinds of stuff for a long time.
Here is the attempt to start cleaning it up by splitting out panic and
oops helpers.
There are several purposes of doing this:
- dropping dependency in bug.h
- dropping a loop by moving out panic_notifier.h
- unload kernel.h from something which has its own domain
At the same time convert users tree-wide to use new headers, although for
the time being include new header back to kernel.h to avoid twisted
indirected includes for existing users.
[akpm@linux-foundation.org: thread_info.h needs limits.h]
[andriy.shevchenko@linux.intel.com: ia64 fix]
Link: https://lkml.kernel.org/r/20210520130557.55277-1-andriy.shevchenko@linux.intel.com
Link: https://lkml.kernel.org/r/20210511074137.33666-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Co-developed-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Wei Liu <wei.liu@kernel.org>
Acked-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Acked-by: Helge Deller <deller@gmx.de> # parisc
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Trying to get the AB8500 charging driver working I ran into a bit
of bitrot: we haven't used the driver for a while so errors in
refactorings won't be noticed.
This one is pretty self evident: use argument to the macro or we
end up with a random pointer to something else.
Cc: stable@vger.kernel.org
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Marcus Cooper <codekipper@gmail.com>
Fixes: 297d716f62 ("power_supply: Change ownership from driver to core")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The continue statement at the end of a for-loop has no effect,
invert the if expression and remove the continue.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
It turns out that the "T3 MRD" DMI_BOARD_NAME value is used in a lot of
different Cherry Trail x5-z8300 / x5-z8350 based Mini-PC / HDMI-stick
models from Ace PC / Meegopad / MinisForum / Wintel (and likely also
other vendors).
Most of the other DMI strings on these boxes unfortunately contain various
generic values like "Default string" or "$(DEFAULT_STRING)", so we cannot
match on them. These devices do have their chassis-type correctly set to a
value of "3" (desktop) which is a pleasant surprise, so also match on that.
This should avoid the quirk accidentally also getting applied to laptops /
tablets (which do actually have a battery). Although in my quite large
database of Bay and Cherry Trail based devices DMIdecode dumps I don't
have any laptops / tables with a board-name of "T3 MRD", so this should
not be an issue.
BugLink: https://askubuntu.com/questions/1206714/how-can-a-mini-pc-be-stopped-from-being-detected-as-a-laptop-with-a-battery/
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
As documented in the updated "Naming" chapter of
Documentation/process/coding-style.rst, usage of the work blacklist
should be avoided where possible.
Rename the list of devices which have no battery to the
axp288_no_battery_list, which also more accurately describes the
contents of the list.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr() does not have any sense (this also allows ACPI
matching via PRP0001, even though it might be not relevant here). This
fixes compile warning (!CONFIG_OF):
drivers/power/supply/bq24190_charger.c:1972:34: warning: ‘bq24190_of_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Signed-off-by: Yu Jiahua <yujiahua1@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This avoids reimplementing the detection logic twice and removes the
possibility of activating charging with 500mA even if a battery is not
detected.
Signed-off-by: Carl Philipp Klemm <philipp@uvos.xyz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This invalidates empty->counter_uah and charge_full when charge_now
indicates that they are grossly wrong and adds some tolerance to
POWER_SUPPLY_PROP_CHARGE_FULL to allow for inaccuracies in the charge
counter and manufacturing tolerances in the battery.
Signed-off-by: Carl Philipp Klemm <philipp@uvos.xyz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Allow disabling and re-enabling battery charging of an axp209 PMIC
through a writable status property. With the current driver code
charging is always on.
This works on the axp209 of Banana {Pi M1+,Pro} and should work on all
AXP chips.
Signed-off-by: Hermann.Lauer@uni-heidelberg.de
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
There are no platforms using the driver with platform data (no board
files with the driver), so the dead code can be dropped.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The driver was reporting POWER_SUPPLY_PROP_ONLINE via platform data
functions or '1' if no platform data was provided. Since there are no
platforms using the driver with platform data (no board files with the
driver), the online property can be simplified to always return '1'.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The driver was reporting POWER_SUPPLY_PROP_STATUS via platform data
functions. Without platform data, the max17040_get_status() functions
returns early with POWER_SUPPLY_STATUS_UNKNOWN. Since there are no
platforms using the driver with platform data (no board files with the
driver), the status property was always unknown.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
When devm_ioremap_resource() fails, a clear enough error message will be
printed by its subfunction __devm_ioremap_resource(). The error
information contains the device name, failure cause, and possibly resource
information.
Therefore, remove the error printing here to simplify code and reduce the
binary size.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The fuel gauge in the RT5033 PMIC has its own I2C bus and interrupt
line. Therefore, it is not actually part of the RT5033 MFD and needs
its own of_match_table to probe properly.
Also, given that it's independent of the MFD, there is actually
no need to make the Kconfig depend on MFD_RT5033. Although the driver
uses the shared <linux/mfd/rt5033.h> header, there is no compile
or runtime dependency on the RT5033 MFD driver.
Cc: Beomho Seo <beomho.seo@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Fixes: b847dd96e6 ("power: rt5033_battery: Add RT5033 Fuel gauge device driver")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The only known BD70528 use-cases are such that the PMIC is controlled
from separate MCU which is not running Linux. I am not aware of
any Linux driver users. Furthermore, it seems there is no demand for
this IC. Let's ease the maintenance burden and drop the driver. We can
always add it back if there is sudden need for it.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Interrupt line can be configured on different hardware in different way,
even inverted. Therefore driver should not enforce specific trigger
type - edge falling - but instead rely on Devicetree to configure it.
The Maxim 14577/77836 datasheets describe the interrupt line as active
low with a requirement of acknowledge from the CPU therefore the edge
falling is not correct.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Iskren Chernev <iskren.chernev@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Interrupt line can be configured on different hardware in different way,
even inverted. Therefore driver should not enforce specific trigger
type - edge falling - but instead rely on Devicetree to configure it.
The Maxim 17047/77693 datasheets describe the interrupt line as active
low with a requirement of acknowledge from the CPU therefore the edge
falling is not correct.
The interrupt line is shared between PMIC and RTC driver, so using level
sensitive interrupt is here especially important to avoid races. With
an edge configuration in case if first PMIC signals interrupt followed
shortly after by the RTC, the interrupt might not be yet cleared/acked
thus the second one would not be noticed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The ac->state field is __le32, not u32. So change the variable we're
temporarily storing it in to __le32 as well.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: e61ffb3445 ("power: supply: Add AC driver for Surface Aggregator Module")
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Currently sbs-battery supports three string properties -
manufacturer, model_name, and chemistry. Buffers for those
properties are currently defined as global variables.
This patch moves those global variables into struct sbs_info
and cache/reuse them as they are all constant values.
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Tested-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Adds properties for setting the maximum current to USB, ADP and Battery
supplies. USB and ADP limits are reset to OTP values upon replugging.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The RC5T619 can detect SDP, CDP and DCP chargers, so let's add support
for it.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This driver is including the legacy GPIO header <linux/gpio.h>
but not using any symbols from it. Delete the include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The PM2301 was only used in tandem with AB9540, part of U9540,
a platform that was cancelled and never deployed in products.
Delete it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The result of container_of() operations is never NULL unless the element
is the first element of the embedded structure, which is not the case here.
The NULL check is therefore unnecessary and misleading. Remove it.
This change was made automatically with the following Coccinelle script.
@@
type t;
identifier v;
statement s;
@@
<+...
(
t v = container_of(...);
|
v = container_of(...);
)
...
when != v
- if (\( !v \| v == NULL \) ) s
...+>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This setting is read directly from the device tree in
the ab8500_charger.c code.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The vendor code tree supplies platform data to enable he
USB charging for AB8500 and AB8500 and disable the AC
charging on the AB8505. This was missed when the driver
was submitted to the mainline kernel.
Fix this by doing what the vendor kernel does: always
register the USB charger, do not register the AC charger
on the AB8505.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Sometimes the code will crash because we haven't enabled
AC or USB charging and thus not created the corresponding
psy device. Fix it by checking that it is there before
notifying.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
