Skge devices installed on some Gigabyte motherboards are not able to
perform 64 dma correctly due to board PCI implementation, so limit
DMA to 32bit if such boards are detected.
Bug was reported here:
https://bugzilla.redhat.com/show_bug.cgi?id=447489
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Tested-by: Luya Tshimbalanga <luya@fedoraproject.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Add ixgbevf and docs files to the maintainers file
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds documentation for the e1000e networking driver.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updated the e1000 networking driver documentation.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the documentation for the ixgbevf (ixgbe virtual
function driver).
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_headroom() is unsigned so "skb_headroom(skb) + toff" is also
unsigned and can't be less than zero. This test was added in 66d50d25:
"u32: negative offset fix" It was supposed to fix a regression.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sctp_asoc_get_hmac() function iterates through a peer's hmac_ids
array and attempts to ensure that only a supported hmac entry is
returned. The current code fails to do this properly - if the last id
in the array is out of range (greater than SCTP_AUTH_HMAC_ID_MAX), the
id integer remains set after exiting the loop, and the address of an
out-of-bounds entry will be returned and subsequently used in the parent
function, causing potentially ugly memory corruption. This patch resets
the id integer to 0 on encountering an invalid id so that NULL will be
returned after finishing the loop if no valid ids are found.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com>
Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two user-controlled allocations in SCTP are subsequently dereferenced as
sockaddr structs, without checking if the dereferenced struct members fall
beyond the end of the allocated chunk. There doesn't appear to be any
information leakage here based on how these members are used and
additional checking, but it's still worth fixing.
[akpm@linux-foundation.org: remove unfashionable newlines, fix gmail tab->space conversion]
Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent patch to allow IGMPv2 responses to IGMPv3 queries
bypasses length checks for valid query lengths, incorrectly
resets the v2_seen timer, and does not support IGMPv1.
The following patch responds with a v2 report as required
by IGMPv2 while correcting the other problems introduced
by the patch.
Signed-Off-By: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 'select' ignores dependencies, drivers that select INET_LRO must
depend on INET. This fixes the broken configuration reported in
<http://article.gmane.org/gmane.linux.kernel/825646>.
Reported-by: Subrata Modak <subrata@linux.vnet.ibm.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit e81963b180.
LRO is now deprecated in favour of GRO, and only a few drivers use it,
so it is desirable to build it as a module in distribution kernels.
The original change to prevent building it as a module was made in an
attempt to avoid the case where some dependents are set to y and some
to m, and INET_LRO can be set to m rather than y. However, the
Kconfig system will reliably set INET_LRO=y in this case.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the condition (3rd arg) passed to sk_wait_event() in
sk_stream_wait_memory(). The incorrect check in sk_stream_wait_memory()
causes the following soft lockup in tcp_sendmsg() when the global tcp
memory pool has exhausted.
>>> snip <<<
localhost kernel: BUG: soft lockup - CPU#3 stuck for 11s! [sshd:6429]
localhost kernel: CPU 3:
localhost kernel: RIP: 0010:[sk_stream_wait_memory+0xcd/0x200] [sk_stream_wait_memory+0xcd/0x200] sk_stream_wait_memory+0xcd/0x200
localhost kernel:
localhost kernel: Call Trace:
localhost kernel: [sk_stream_wait_memory+0x1b1/0x200] sk_stream_wait_memory+0x1b1/0x200
localhost kernel: [<ffffffff802557c0>] autoremove_wake_function+0x0/0x40
localhost kernel: [ipv6:tcp_sendmsg+0x6e6/0xe90] tcp_sendmsg+0x6e6/0xce0
localhost kernel: [sock_aio_write+0x126/0x140] sock_aio_write+0x126/0x140
localhost kernel: [xfs:do_sync_write+0xf1/0x130] do_sync_write+0xf1/0x130
localhost kernel: [<ffffffff802557c0>] autoremove_wake_function+0x0/0x40
localhost kernel: [hrtimer_start+0xe3/0x170] hrtimer_start+0xe3/0x170
localhost kernel: [vfs_write+0x185/0x190] vfs_write+0x185/0x190
localhost kernel: [sys_write+0x50/0x90] sys_write+0x50/0x90
localhost kernel: [system_call+0x7e/0x83] system_call+0x7e/0x83
>>> snip <<<
What is happening is, that the sk_wait_event() condition passed from
sk_stream_wait_memory() evaluates to true for the case of tcp global memory
exhaustion. This is because both sk_stream_memory_free() and vm_wait are true
which causes sk_wait_event() to *not* call schedule_timeout().
Hence sk_stream_wait_memory() returns immediately to the caller w/o sleeping.
This causes the caller to again try allocation, which again fails and again
calls sk_stream_wait_memory(), and so on.
[ Bug introduced by commit c1cbe4b7ad
("[NET]: Avoid atomic xchg() for non-error case") -DaveM ]
Signed-off-by: Nagendra Singh Tomar <tomer_iisc@yahoo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roger Luethi noticed packets for unknown VLANs getting silently dropped
even in promiscuous mode.
Check for promiscuous mode in __vlan_hwaccel_rx() and vlan_gro_common()
before drops.
As suggested by Patrick, mark such packets to have skb->pkt_type set to
PACKET_OTHERHOST to make sure they are dropped by IP stack.
Reported-by: Roger Luethi <rl@hellgate.ch>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Retrieve the header after doing pskb_may_pull since, pskb_may_pull
could change the buffer structure.
This is based on the comment given by Eric Dumazet on Phonet
Pipe controller patch for a similar problem.
Signed-off-by: Kumar Sanghvi <kumar.sanghvi@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
uml_net_set_mac() was broken and luckily it was never used, before.
What it was trying to do is spin_lock before memcopy the mac address.
Linus attempted to fix it in assumption that someone decided the
lock was needed. But since it was never ever used at all, and was
just dead code, I think we can assume that it is not needed, after
all.
On the other hand patch [f25c80a4] was trying to use eth_mac_addr()
in eth_configure(), *which was the real fallout*. Because of state
checks done inside eth_mac_addr() the address was never set. I have
not reintroduced the memcpy wrapper, but I've put a comment for future
cats.
The code now is back to exactly as it was before [f25c80a4]. With
the cleanup applied. If the spin_lock is indeed needed then a contender
should supply a test case that fails, then fix it with the proper
locking, as a separate unrelated patch.
CC: Julia Lawall <julia@diku.dk>
CC: David S. Miller <davem@davemloft.net>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Al Viro <viro@ZenIV.linux.org.uk>
Tested-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GRE tunnel driver needs to invoke icmpv6 helpers in the
ipv6 stack when ipv6 support is enabled.
Therefore if IPV6 is enabled, we have to enforce that GRE's
enabling (modular or static) matches that of ipv6.
Reported-by: Patrick McHardy <kaber@trash.net>
Reported-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes kernel Bugzilla Bug 18952
This patch adds a syn_set parameter to the retransmits_timed_out()
routine and updates its callers. If not set, TCP_RTO_MIN is taken
as the calculation basis as before. If set, TCP_TIMEOUT_INIT is
used instead, so that sysctl_syn_retries represents the actual
amount of SYN retransmissions in case no SYNACKs are received when
establishing a new connection.
Signed-off-by: Damian Lukowski <damian@tvk.rwth-aachen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
iwl3945's scan_completed calls into the mac80211 stack which triggers a
warn on if there is no scan outstanding.
This can be avoided by not calling scan_completed but abort_scan in
iwl3945_request_scan in the done: branch of the function which is used
as an error out.
The done: branch seems to be an error-out branch, as, for example, if
iwl_is_ready(priv) returns false the done: branch is executed.
NOTE:
I'm not familiar with the driver at all.
I just quickly scanned as a reaction to
https://bugzilla.kernel.org/show_bug.cgi?id=17722
the users of scan_completed in the iwl3945 driver and noted the odd
discrepancy between the comment above this instance and the comment in
mac80211 scan_completed function.
Signed-off-by: Florian Mickler <florian@mickler.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes kernel bugzilla #16603
tcp_sendmsg() truncates iov_len to an 'int' which a 4GB write to write
zero bytes, for example.
There is also the problem higher up of how verify_iovec() works. It
wants to prevent the total length from looking like an error return
value.
However it does this using 'int', but syscalls return 'long' (and
thus signed 64-bit on 64-bit machines). So it could trigger
false-positives on 64-bit as written. So fix it to use 'long'.
Reported-by: Olaf Bonorden <bono@onlinehome.de>
Reported-by: Daniel Büse <dbuese@gmx.de>
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
p9_virtio_create will only compare the the channel's tag characters
against the device name till the end of the channel's tag but not till
the end of the device name. This means that if a user defines channels
with the tags foo and foobar then he would mount foo when he requested
foonot and may mount foo when he requested foobar.
Thus it is necessary to check both string lengths against each other in
case of a successful partial string match.
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the interface is up, using ethtool breaks it because:
a) link is put down but media_timer interval is not shortened to NO_LINK
b) rxtx is stopped but not restarted
Also manual 10baseT-HD (and probably FD too - untested) mode does not work -
the link is forced up, packets are transmitted but nothing is received.
Changing CSR14 value to match documentation (not disabling link check) fixes this.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv4 and IPv6 have separate neighbour tables, so
the warning messages should be distinguishable.
[ Add a suitable message prefix on the ipv4 side as well -DaveM ]
Signed-off-by: Ulrich Weber <uweber@astaro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When TCP uses FACK algorithm to mark lost packets in
tcp_mark_head_lost(), if the number of packets in the (TSO) skb is
greater than the number of packets that should be marked lost, TCP
incorrectly exits the loop and marks no packets lost in the skb. This
underestimates tp->lost_out and affects the recovery/retransmission.
This patch fargments the skb and marks the correct amount of packets
lost.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch (commit 690a1f2002) added a
new call site for acpi_set_WOL() without checking that the function is
actually suitable to be called via
vortex_set_wol+0xcd/0xe0 [3c59x]
dev_ethtool+0xa5a/0xb70
dev_ioctl+0x2e0/0x4b0
T.961+0x49/0x50
sock_ioctl+0x47/0x290
do_vfs_ioctl+0x7f/0x340
sys_ioctl+0x80/0xa0
system_call_fastpath+0x16/0x1b
i.e. outside of code paths run when the device is not yet enabled or
already disabled. In particular, putting the device into D3hot is a
pretty bad idea when it was already brought up.
Furthermore, all prior callers of the function made sure they're
actually dealing with a PCI device, while the newly added one didn't.
In the same spirit, the .get_wol handler shouldn't indicate support
for WOL for non-PCI devices.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean up a missing exit path in the ipv6 module init routines. In
addrconf_init we call ipv6_addr_label_init which calls register_pernet_subsys
for the ipv6_addr_label_ops structure. But if module loading fails, or if the
ipv6 module is removed, there is no corresponding unregister_pernet_subsys call,
which leaves a now-bogus address on the pernet_list, leading to oopses in
subsequent registrations. This patch cleans up both the failed load path and
the unload path. Tested by myself with good results.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
include/net/addrconf.h | 1 +
net/ipv6/addrconf.c | 11 ++++++++---
net/ipv6/addrlabel.c | 5 +++++
3 files changed, 14 insertions(+), 3 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
Freeing netdev without free_netdev() leads to net, tx leaks.
I might lead to dereferencing freed pointer.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
@@
struct net_device* dev;
@@
-kfree(dev)
+free_netdev(dev)
Signed-off-by: David S. Miller <davem@davemloft.net>
Freeing netdev without free_netdev() leads to net, tx leaks.
I might lead to dereferencing freed pointer.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
@@
struct net_device* dev;
@@
-kfree(dev)
+free_netdev(dev)
Signed-off-by: David S. Miller <davem@davemloft.net>
Freeing netdev without free_netdev() leads to net, tx leaks.
I might lead to dereferencing freed pointer.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
@@
struct net_device* dev;
@@
-kfree(dev)
+free_netdev(dev)
Signed-off-by: David S. Miller <davem@davemloft.net>
Freeing netdev without free_netdev() leads to net, tx leaks.
I might lead to dereferencing freed pointer.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
@@
struct net_device* dev;
@@
-kfree(dev)
+free_netdev(dev)
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables auto loading for the smsc911x ethernet driver.
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset queue mapping when an skb is reentering the stack via a tunnel.
On second pass, the queue mapping from the original device is no
longer valid.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
You can't call atomic_notifier_chain_unregister() while in atomic context.
Fix, call un/register_atmdevice_notifier in module __init and __exit.
Bug report:
http://comments.gmane.org/gmane.linux.network/172603
Reported-by: Mikko Vinni <mmvinni@yahoo.com>
Tested-by: Mikko Vinni <mmvinni@yahoo.com>
Signed-off-by: Karl Hiramoto <karl@hiramoto.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compex FreedomLine 32 PnP-PCI2 cards have only TP and BNC connectors but the
SROM contains AUI port too. When TP loses link, the driver switches to
non-existing AUI port (which reports that carrier is always present).
Connecting TP back generates LinkPass interrupt but de_media_interrupt() is
broken - it only updates the link state of currently connected media, ignoring
the fact that LinkPass and LinkFail bits of MacStatus register belong to the
TP port only (the chip documentation says that).
This patch changes de_media_interrupt() to switch media to TP when link goes
up (and media type is not locked) and also to update the link state only when
the TP port is used.
Also the NonselPortActive (and also SelPortActive) bits of SIAStatus register
need to be cleared (by writing 1) after reading or they're useless.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least my 21041 cards come out of suspend with bus mastering disabled so
they did not work after resume(no data transferred).
After adding pci_set_master(), the driver oopsed immediately on resume -
because de_clean_rings() is called on suspend but de_init_rings() call
was missing in resume.
Also disable link (reset SIA) before sleep (de4x5 does this too).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least on older 21041-AA chips (mine is rev. 11), TP duplex autonegotiation
causes the card not to work at all (link is up but no packets are transmitted).
de4x5 disables autonegotiation completely. But it seems to work on newer
(21041-PA rev. 21) so disable it only on rev<20 chips.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have for each socket :
One spinlock (sk_slock.slock)
One rwlock (sk_callback_lock)
Possible scenarios are :
(A) (this is used in net/sunrpc/xprtsock.c)
read_lock(&sk->sk_callback_lock) (without blocking BH)
<BH>
spin_lock(&sk->sk_slock.slock);
...
read_lock(&sk->sk_callback_lock);
...
(B)
write_lock_bh(&sk->sk_callback_lock)
stuff
write_unlock_bh(&sk->sk_callback_lock)
(C)
spin_lock_bh(&sk->sk_slock)
...
write_lock_bh(&sk->sk_callback_lock)
stuff
write_unlock_bh(&sk->sk_callback_lock)
spin_unlock_bh(&sk->sk_slock)
This (C) case conflicts with (A) :
CPU1 [A] CPU2 [C]
read_lock(callback_lock)
<BH> spin_lock_bh(slock)
<wait to spin_lock(slock)>
<wait to write_lock_bh(callback_lock)>
We have one problematic (C) use case in inet_csk_listen_stop() :
local_bh_disable();
bh_lock_sock(child); // spin_lock_bh(&sk->sk_slock)
WARN_ON(sock_owned_by_user(child));
...
sock_orphan(child); // write_lock_bh(&sk->sk_callback_lock)
lockdep is not happy with this, as reported by Tetsuo Handa
It seems only way to deal with this is to use read_lock_bh(callbacklock)
everywhere.
Thanks to Jarek for pointing a bug in my first attempt and suggesting
this solution.
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Tested-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Jarek Poplawski <jarkao2@gmail.com>
Tested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 8c0c709eea
Author: Johannes Berg <johannes@sipsolutions.net>
Date: Wed Nov 25 17:46:15 2009 +0100
mac80211: move cmntr flag out of rx flags
moved the CMTR flag into the skb's status, and
in doing so introduced a use-after-free -- when
the skb has been handed to cooked monitors the
status setting will touch now invalid memory.
Additionally, moving it there has effectively
discarded the optimisation -- since the bit is
only ever set on freed SKBs, and those were a
copy, it could never be checked.
For the current release, fixing this properly
is a bit too involved, so let's just remove the
problematic code and leave userspace with one
copy of each frame for each virtual interface.
Cc: stable@kernel.org [2.6.33+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For non-managed versions of 82579, set the bit that prevents the hardware
from automatically configuring the PHY after resets only when the driver
performs a reset, clear the bit after resets. This is so the hardware can
configure the PHY automatically when the part is reset in a manner that is
not controlled by the driver (e.g. in a virtual environment via PCI FLR)
otherwise the PHY will be mis-configured causing issues such as failing to
link at 1000Mbps.
For managed versions of 82579, keep the previous behavior since the
manageability firmware will handle the PHY configuration.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The subject workaround was causing CRC errors due to writing the wrong
register with updates of the RCTL register. It was also found that the
workaround function which modifies the RCTL register was being called in
the middle of a read-modify-write operation of the RCTL register, so the
function call has been moved appropriately. Lastly, jumbo frames must not
be allowed when CRC stripping is disabled by a module parameter because the
workaround requires the CRC be stripped.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 82579, there is a hardware bug that can cause received packets to not
get transferred from the PHY to the MAC due to K1 (a power saving feature
of the PHY-MAC interconnect similar to ASPM L1). Since the MAC controls
the accounting of missed packets, these will go unnoticed. Workaround the
issue by setting the K1 beacon duration according to the link speed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two recent patches to cleanup the reset[1] and initial PHY configuration[2]
code paths for ICH/PCH devices inadvertently left out a 10msec delay and
device ID check respectively which are necessary for the 82566DC (device id
0x104b) to be configured properly, otherwise it will not get link.
[1] commit e98cac447c
[2] commit 3f0c16e844
CC: stable@kernel.org
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the hardware is prevented from performing automatic PHY configuration
(the driver does it instead), the OEM_WRITE_ENABLE bit in the EXTCNF_CTRL
register will not get cleared preventing the SMBus address and the LED
configuration to be written to the PHY registers. On 82579, do not check
the OEM_WRITE_ENABLE bit.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When going to Sx, disable gigabit in PHY (e1000_oem_bits_config_ich8lan)
in addition to the MAC before configuring PHY wakeup otherwise the PHY
configuration writes might be missed. Also write the LED configuration
and SMBus address to the PHY registers (e1000_oem_bits_config_ich8lan and
e1000_write_smbus_addr, respectively). The reset is no longer needed
since re-auto-negotiation is forced in e1000_oem_bits_config_ich8lan and
leaving it in causes issues with auto-negotiating the link.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
otherwise ECT(1) bit will get interpreted as RTO_ONLINK
and routing will fail with XfrmOutBundleGenError.
Signed-off-by: Ulrich Weber <uweber@astaro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
They are allocated in atl1_setup_ring_resources, zero out the pointers
in atl1_free_ring_resources (like the other resources).
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Acked-by: Chris Snook <chris.snook@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
adapter->cmb.cmb is initialized when the device is opened and freed when
it's closed. Accessing it unconditionally during resume results either
in a crash (NULL pointer dereference, when the interface has not been
opened yet) or data corruption (when the interface has been used and
brought down adapter->cmb.cmb points to a deallocated memory area).
Cc: stable@kernel.org
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Acked-by: Chris Snook <chris.snook@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
