2
0
mirror of https://github.com/edk2-porting/linux-next.git synced 2024-12-23 04:34:11 +08:00
Commit Graph

58677 Commits

Author SHA1 Message Date
Frederic Danis
391d8a2da7 NFC: Add NCI over SPI receive
Before any operation, driver interruption is de-asserted to prevent
race condition between TX and RX.

Transaction starts by emitting "Direct read" and acknowledged mode
bytes. Then packet length is read allowing to allocate correct NCI
socket buffer. After that payload is retrieved.

A delay after the transaction can be added.
This delay is determined by the driver during nci_spi_allocate_device()
call and can be 0.

If acknowledged mode is set:
- CRC of header and payload is checked
- if frame reception fails (CRC error): NACK is sent
- if received frame has ACK or NACK flag: unblock nci_spi_send()

Payload is passed to NCI module.

At the end, driver interruption is re asserted.

Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-06-14 13:44:16 +02:00
Frederic Danis
ee9596d467 NFC: Add NCI over SPI send
Before any operation, driver interruption is de-asserted to prevent
race condition between TX and RX.

The NCI over SPI header is added in front of NCI packet.
If acknowledged mode is set, CRC-16-CCITT is added to the packet.
Then the packet is forwarded to SPI module to be sent.

A delay after the transaction is added.
This delay is determined by the driver during nci_spi_allocate_device()
call and can be 0.

After data has been sent, driver interruption is re-asserted.

If acknowledged mode is set, nci_spi_send will block until
acknowledgment is received.

Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-06-14 13:44:15 +02:00
Frederic Danis
8a00a61b0e NFC: Add basic NCI over SPI
The NFC Forum defines a transport interface based on
Serial Peripheral Interface (SPI) for the NFC Controller
Interface (NCI).

This module implements the SPI transport of NCI, calling SPI module
directly to read/write data to NFC controller (NFCC).

NFCC driver should provide functions performing device open and close.
It should also provide functions asserting/de-asserting interruption
to prevent TX/RX race conditions.
NFCC driver can also fix a delay between transactions if needed by
the hardware.

Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-06-14 13:44:03 +02:00
Eric Lapuyade
9a695d23aa NFC: HCI: Implement fw_upload ops
This is a simple forward to the HCI driver. When driver is done with the
operation, it shall directly notify NFC Core by calling
nfc_fw_upload_done().

Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-06-14 00:26:09 +02:00
Eric Lapuyade
9674da8759 NFC: Add firmware upload netlink command
As several NFC chipsets can have their firmwares upgraded and
reflashed, this patchset adds a new netlink command to trigger
that the driver loads or flashes a new firmware. This will allows
userspace triggered firmware upgrade through netlink.
The firmware name or hint is passed as a parameter, and the driver
will eventually fetch the firmware binary through the request_firmware
API.
The cmd can only be executed when the nfc dev is not in use. Actual
firmware loading/flashing is an asynchronous operation. Result of the
operation shall send a new event up to user space through the nfc dev
multicast socket. During operation, the nfc dev is not openable and
thus not usable.

Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-06-14 00:26:08 +02:00
Frederic Danis
1095e69f47 NFC: NCI: Fix skb->dev usage
skb->dev is used for carrying a net_device pointer and not
an nci_dev pointer.

Remove usage of skb-dev to carry nci_dev and replace it by parameter
in nci_recv_frame(), nci_send_frame() and driver send() functions.

NfcWilink driver is also updated to use those functions.

Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-06-14 00:25:53 +02:00
John W. Linville
812fd64596 Merge branch 'for-john' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Conflicts:
	drivers/net/wireless/iwlwifi/mvm/mac80211.c
2013-06-12 15:39:05 -04:00
John W. Linville
861bca265e Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
Conflicts:
	drivers/net/wireless/ath/ath9k/Kconfig
	net/mac80211/iface.c
2013-06-12 14:35:23 -04:00
Johan Hedberg
96570ffcca Bluetooth: Fix mgmt handling of power on failures
If hci_dev_open fails we need to ensure that the corresponding
mgmt_set_powered command gets an appropriate response. This patch fixes
the missing response by adding a new mgmt_set_powered_failed function
that's used to indicate a power on failure to mgmt. Since a situation
with the device being rfkilled may require special handling in user
space the patch uses a new dedicated mgmt status code for this.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-12 10:20:55 -04:00
Ashok Nagarajan
ffb3cf3000 {nl,mac,cfg}80211: Allow user to configure basic rates for mesh
Currently mesh uses mandatory rates as the default basic rates. Allow basic
rates to be configured during mesh join. Basic rates are applied only if
channel is also provided with mesh join command.

Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
[some whitespace fixes, refuse basic rates w/o channel]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-06-11 14:24:36 +02:00
Colleen Twitty
8e7c053853 {nl,cfg}80211: make peer link expiration time configurable
If a STA has a peer that it hasn't seen any tx activity
from for a certain length of time, the peer link is
expired. This means the inactive STA is removed from the
list of peers and that STA is not considered a peer again
unless it re-peers.  Previously, this inactivity time was
always 30 minutes.  Now, add it to the mesh configuration
and allow it to be configured.  Retain 30 minutes as a
default value.

Signed-off-by: Colleen Twitty <colleen@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-06-11 14:16:29 +02:00
Felix Fietkau
a0a2af7655 nl80211: add kernel-doc for NL80211_FEATURE_ACTIVE_MONITOR
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-06-11 14:14:32 +02:00
Johannes Berg
780b40df12 wireless: fix kernel-doc
Some kernel-doc fixes for forgotten fields and renamed things.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-06-05 09:33:32 +02:00
Alexander Bondar
989c6505cd mac80211: Use suitable semantics for beacon availability indication
Currently beacon availability upon association is marked by have_beacon
flag of assoc_data structure that becomes unavailable when association
completes. However beacon availability indication is required also after
association to inform a driver. Currently dtim_period parameter is used
for this purpose. Move have_beacon flag to another structure, persistant
throughout a interface's life cycle. Use suitable sematics for beacon
availability indication.

Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
[fix another instance of BSS_CHANGED_DTIM_PERIOD in docs]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-06-05 09:12:20 +02:00
Johannes Berg
ceca7b7121 cfg80211: separate internal SME implementation
The current internal SME implementation in cfg80211 is
very mixed up with the MLME handling, which has been
causing issues for a long time. There are three things
that the implementation has to provide:
 * a basic SME implementation for nl80211's connect()
   call (for drivers implementing auth/assoc, which is
   really just mac80211) and wireless extensions
 * MLME events for the userspace SME
 * SME events (connected, disconnected etc.) for all
   different SME implementation possibilities (driver,
   cfg80211 and userspace)

To achieve these goals it isn't necessary to track the
software SME's connection status outside of it's state
(which is the part that caused many issues.) Instead,
track it only in the SME data (wdev->conn) and in the
general case only track whether the wdev is connected
or not (via wdev->current_bss.)

Also separate the internal implementation to not have
callbacks from the SME events, but rather call it from
the API functions that the driver (or rather mac80211)
calls. This separates the code better.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-06-04 13:03:11 +02:00
Johannes Berg
6ff57cf888 cfg80211/mac80211: clean up cfg80211 SME APIs
Do some cleanups in the cfg80211 SME APIs, which are
only used by mac80211.

Most of these functions get a frame passed, and there
isn't really any reason to export multiple functions
as cfg80211 can check the frame type instead, do that.

Additionally, the API functions have confusing names
like cfg80211_send_...() which was meant to indicate
that it sends an event to userspace, but gets a bit
confusing when there's both TX and RX and they're not
all clearly labeled.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-06-04 13:03:10 +02:00
Johannes Berg
51217cee3a Merge remote-tracking branch 'wireless-next/master' into HEAD
Merge to get the wil6210 changes that a cfg80211 change needs.
A conflict in drivers/net/wireless/ath/ath9k/init.c was just
whitespace changes.

Also fix a semantic conflict due to cw1200 using WoWLAN which
I had modified in my tree.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-06-04 13:02:42 +02:00
Felix Fietkau
d6d23de278 mac80211: add a tx control flag to indicate PS-Poll/uAPSD response
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-06-04 12:41:36 +02:00
John W. Linville
133eb82f09 Merge branch 'for-john' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next 2013-06-03 15:55:37 -04:00
Solomon Peachy
4da2a54a84 cw1200: rename the cw1200 platform definition header
My previous patch just moved the file, but it also needed to be renamed
to conform to proper conventions.

Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-03 15:54:56 -04:00
Solomon Peachy
7c0b6f49db cw1200: Rework SDIO platform support to prevent build problems.
Based on discussions with And Bergmann, this patch changes the SDIO
platform code to default to supporting the Sagrad devices, allowing for
it to be overridden in board setup code.  This renders the cw1200_sagrad
module suplerflous, so it is now removed.

It also moves the documentation that was in the cw1200_sagrad source to
the platform header.

Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-03 15:54:55 -04:00
Solomon Peachy
6dd64a304e cw1200: Replace use of 'struct resource' with 'int' for GPIO fields.
The only advantage of 'struct resource' is that it lets us assign names
as part of the platform data.  Unfortunately since we are using platform
data, we are already limited to a single instance of each driver,
rendering this moot.

So, replace the struct resources with ints, resulting in cleaner code.

This was based on a suggestion from Arnd Bergmann.

Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-03 15:54:55 -04:00
Solomon Peachy
c992219825 cw1200: move platform_data header to correct location.
(As suggested by Arnd Bergmann)

Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-03 15:54:54 -04:00
Johannes Berg
964dc9e2c3 cfg80211: take WoWLAN support information out of wiphy struct
There's no need to take up the space for devices that don't
support WoWLAN, and most drivers can even make the support
data static const (except where it's modified at runtime.)

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-06-03 18:43:34 +02:00
Jacob Minshall
e05ecccdf7 mac80211: set mesh formation field properly
Cap max peerings at 63 in accordance with IEEE-2012 8.4.2.100.7.
Triggers a beacon regeneration every time the number of peerings changes.
Previously this would only happen if the "accepting peerings" bit changed.

Signed-off-by: Jacob Minshall <jacob@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-06-03 17:03:18 +02:00
Solomon Peachy
a910e4a94f cw1200: add driver for the ST-E CW1100 & CW1200 WLAN chipsets
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-05-29 15:26:40 -04:00
John W. Linville
933faa43ab Merge branch 'for-john' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next 2013-05-29 14:51:50 -04:00
Johannes Berg
bd5e14fb77 cfg80211: remove cleanup_work kernel-doc
I evidently forgot this when removing the work itself.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-29 09:11:57 +02:00
Felix Fietkau
e057d3c31b cfg80211: support an active monitor interface flag
An active monitor interface is one that is used for communication (via
injection). It is expected to ACK incoming unicast packets. This is
useful for running various 802.11 testing utilities that associate to an
AP via injection and manage the state in user space.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-29 09:11:44 +02:00
Johannes Berg
6abb9cb99f cfg80211: make WoWLAN configuration available to drivers
Make the current WoWLAN configuration available to drivers
at runtime. This isn't really useful for the normal WoWLAN
behaviour and accessing it can also be racy, but drivers
may use it for testing the WoWLAN device behaviour while
the host stays up & running to observe the device.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-27 15:10:58 +02:00
Johannes Berg
8d61ffa5e0 cfg80211/mac80211: use cfg80211 wdev mutex in mac80211
Using separate locks in cfg80211 and mac80211 has always
caused issues, for example having to unlock in places in
mac80211 to call cfg80211, which even needed a framework
to make cfg80211 calls after some functions returned etc.

Additionally, I suspect some issues people have reported
with the cfg80211 state getting confused could be due to
such issues, when cfg80211 is asking mac80211 to change
state but mac80211 is in the process of telling cfg80211
that the state changed (in another way.)

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-25 00:02:16 +02:00
Johannes Berg
5fe231e873 cfg80211: vastly simplify locking
Virtually all code paths in cfg80211 already (need to) hold
the RTNL. As such, there's little point in having another
four mutexes for various parts of the code, they just cause
lock ordering issues (and much of the time, the RTNL and a
few of the others need thus be held.)

Simplify all this by getting rid of the extra four mutexes
and just use the RTNL throughout. Only a few code changes
were needed to do this and we can get rid of a work struct
for bonus points.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-25 00:02:15 +02:00
Johannes Berg
dde7dc759b Merge remote-tracking branch 'mac80211/master' into mac80211-next 2013-05-25 00:01:30 +02:00
Ashok Nagarajan
b422c6cd7e {cfg,mac}80211: move mandatory rates calculation to cfg80211
Move mandatory rates calculation to cfg80211, shared with non mac80211 drivers.

Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
[extend documentation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-24 23:54:43 +02:00
Jouni Malinen
5e4b6f5698 cfg80211: Allow TDLS peer AID to be configured for VHT
VHT uses peer AID in the PARTIAL_AID field in TDLS frames. The current
design for TDLS is to first add a dummy STA entry before completing TDLS
Setup and then update information on this STA entry based on what was
received from the peer during the setup exchange.

In theory, this could use NL80211_ATTR_STA_AID to set the peer AID just
like this is used in AP mode to set the AID of an association station.
However, existing cfg80211 validation rules prevent this attribute from
being used with set_station operation. To avoid interoperability issues
between different kernel and user space version combinations, introduce
a new nl80211 attribute for the purpose of setting TDLS peer AID. This
attribute can be used in both the new_station and set_station
operations. It is not supposed to be allowed to change the AID value
during the lifetime of the STA entry, but that validation is left for
drivers to do in the change_station callback.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-24 22:36:28 +02:00
Oleksij Rempel
786677d100 mac80211: add STBC flag for radiotap
Some chips can tell us if received frame was
encoded with STBC or not. To make this information available
in user space we can use updated radiotap specification:
http://www.radiotap.org/defined-fields/MCS

This patch will set number of STBC encoded spatial streams (Nss).
The HAVE_STBC flag should be provided by driver.

Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-24 12:07:25 +02:00
Rafał Miłecki
78e578c5b4 bcma: support SPROM rev 10
This is pretty much the same as rev 9, there are just 2 extra fields we
know about, but are not used/stored yet anyway.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-05-22 15:08:44 -04:00
Rafał Miłecki
d4988d4c73 bcma: add more core IDs
PCIe and ARM CR4 cores were found on 14e4:43b1 AKA BCM4352.

Reported-by: Gabriel Thörnblad <gabriel@thornblad.com>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-05-17 14:31:05 -04:00
Colleen Twitty
6e16d90b52 cfg80211: Userspace may inform kernel of mesh auth method.
Authentication takes place in userspace, but the beacon is
generated in the kernel.  Allow userspace to inform the
kernel of the authentication method so the appropriate
mesh config IE can be set prior to beacon generation when
joining the MBSS.

Signed-off-by: Colleen Twitty <colleen@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-16 22:39:43 +02:00
Johannes Berg
4325f6caad wireless: move crypto constants to ieee80211.h
mac80211 and the Intel drivers all define crypto
constants, move them to ieee80211.h instead.

Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-16 22:39:41 +02:00
Robert P. J. Day
03f831a6f7 wireless: fix kerneldoc content in *80211.h files.
Make kerneldoc content match header file content, no functional
change.

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-16 22:39:39 +02:00
Marcel Holtmann
fb4e156886 nl80211: Add generic netlink module alias for cfg80211/nl80211
To support auto-loading of wireless modules from netlink users, add module
alias for nl80211 family.

This also adds NL80211_GENL_NAME constant to define the "nl80211" netlink
family name as part of uapi.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-16 22:39:39 +02:00
Felix Fietkau
ef0621e805 mac80211: add support for per-chain signal strength reporting
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[fix unit documentation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-16 22:39:38 +02:00
Felix Fietkau
119363c7dc cfg80211: add support for per-chain signal strength reporting
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-16 22:39:37 +02:00
Felix Fietkau
f6b3d85f7f mac80211: fix spurious RCU warning and update documentation
Document rx vs tx status concurrency requirements.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-16 22:38:05 +02:00
Linus Torvalds
26b840ae5d The majority of these changes are from Masami Hiramatsu bringing
kprobes up to par with the latest changes to ftrace (multi buffering
 and the new function probes).
 
 He also discovered and fixed some bugs in doing so. When pulling in his
 patches, I also found a few minor bugs as well and fixed them.
 
 This also includes a compile fix for some archs that select the ring buffer
 but not tracing.
 
 I based this off of the last patch you took from me that fixed the merge
 conflict error, as that was the commit that had all the changes I needed
 for this set of changes.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.12 (GNU/Linux)
 
 iQEcBAABAgAGBQJRjYnJAAoJEOdOSU1xswtMg9EH/iFs438FgrNMk2ZdQftmqcqA
 cqcactHo1mmoHjAoLZT/oDBjEThhVUuqzMXrFRutSYcTh4PsQEC3arX0mpsC+T12
 UEEV/tZS3TXH+GXEyrOit/O3kzntQcDHwJDV4+0n80IrJmw4IDZbnV3R8DWjS6wp
 so+dq0A1pwehcG/upgpw1oTKsGv1G/p6vyf968B6W44icHEClLiph4JE2kzE6D3r
 fzSpOLaQoBEvwIRf6xRKxi240VqIItXwfG7pwNpPpSC37gRLzm74zGr+Sj93/k1y
 pARbZ/5XO7/pcVYQYupErRAoV5in+QMZ67k5G1vQIvyOS9r039catbQf/7PkzcI=
 =EZCE
 -----END PGP SIGNATURE-----

Merge tag 'trace-fixes-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace

Pull tracing/kprobes update from Steven Rostedt:
 "The majority of these changes are from Masami Hiramatsu bringing
  kprobes up to par with the latest changes to ftrace (multi buffering
  and the new function probes).

  He also discovered and fixed some bugs in doing so.  When pulling in
  his patches, I also found a few minor bugs as well and fixed them.

  This also includes a compile fix for some archs that select the ring
  buffer but not tracing.

  I based this off of the last patch you took from me that fixed the
  merge conflict error, as that was the commit that had all the changes
  I needed for this set of changes."

* tag 'trace-fixes-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing/kprobes: Support soft-mode disabling
  tracing/kprobes: Support ftrace_event_file base multibuffer
  tracing/kprobes: Pass trace_probe directly from dispatcher
  tracing/kprobes: Increment probe hit-count even if it is used by perf
  tracing/kprobes: Use bool for retprobe checker
  ftrace: Fix function probe when more than one probe is added
  ftrace: Fix the output of enabled_functions debug file
  ftrace: Fix locking in register_ftrace_function_probe()
  tracing: Add helper function trace_create_new_event() to remove duplicate code
  tracing: Modify soft-mode only if there's no other referrer
  tracing: Indicate enabled soft-mode in enable file
  tracing/kprobes: Fix to increment return event probe hit-count
  ftrace: Cleanup regex_lock and ftrace_lock around hash updating
  ftrace, kprobes: Fix a deadlock on ftrace_regex_lock
  ftrace: Have ftrace_regex_write() return either read or error
  tracing: Return error if register_ftrace_function_probe() fails for event_enable_func()
  tracing: Don't succeed if event_enable_func did not register anything
  ring-buffer: Select IRQ_WORK
2013-05-11 17:04:59 -07:00
Linus Torvalds
4c4445013f SCSI for-linus on 20130510
This is the final round of SCSI patches for the merge window.  It consists
 mostly of driver updates (bnx2fc, ibmfc, fnic, lpfc, be2iscsi, pm80xx, qla4x
 and ipr).  There's also the power management updates that complete the patches
 in Jens' tree, an iscsi refcounting problem fix from the last pull, some dif
 handling in scsi_debug fixes, a few nice code cleanups and an error handling
 busy bug fix.
 
 Signed-off-by: James Bottomley <JBottomley@Parallels.com>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.19 (GNU/Linux)
 
 iQEcBAABAgAGBQJRjQsqAAoJEDeqqVYsXL0MayMH/iDncN0swy/Y2Pfh31YHRcvG
 pPTsx/WgQogg5WDeG1XRPmgDJBmJKeSO7OcIZ/AWz+8BJkZbDLfdSp9ugg8ZrrsN
 yAa3lZoOfxhf43AEaUpgORHGj39O+QfoLq3mdo44A57ro30YotIaMvCiqv+baPSL
 Z8K7O/TmmHmOeir3Gl05qrO6PKvQkNnHYZoF1lBiHypUJk51cuTmHrfY6mb2ktXc
 7aElSXSbpUcqQQ8QHnXO/3r6VPkYjhznvo8q8rcLvqQqRnTdLF5Su8vDuyMbbJcU
 svu30wRaBik3XvIfppGhukrYeU5ooj13zZAUY9NIf2vc2wjpMUlRNNZ0uSsHzOw=
 =6cOg
 -----END PGP SIGNATURE-----

Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi

Pull second SCSI update from James "Jaj B" Bottomley:
 "This is the final round of SCSI patches for the merge window.  It
  consists mostly of driver updates (bnx2fc, ibmfc, fnic, lpfc,
  be2iscsi, pm80xx, qla4x and ipr).

  There's also the power management updates that complete the patches in
  Jens' tree, an iscsi refcounting problem fix from the last pull, some
  dif handling in scsi_debug fixes, a few nice code cleanups and an
  error handling busy bug fix."

* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (92 commits)
  [SCSI] qla2xxx: Update firmware link in Kconfig file.
  [SCSI] iscsi class, qla4xxx: fix sess/conn refcounting when find fns are used
  [SCSI] sas: unify the pointlessly separated enums sas_dev_type and sas_device_type
  [SCSI] pm80xx: thermal, sas controller config and error handling update
  [SCSI] pm80xx: NCQ error handling changes
  [SCSI] pm80xx: WWN Modification for PM8081/88/89 controllers
  [SCSI] pm80xx: Changed module name and debug messages update
  [SCSI] pm80xx: Firmware flash memory free fix, with addition of new memory region for it
  [SCSI] pm80xx: SPC new firmware changes for device id 0x8081 alone
  [SCSI] pm80xx: Added SPCv/ve specific hardware functionalities and relevant changes in common files
  [SCSI] pm80xx: MSI-X implementation for using 64 interrupts
  [SCSI] pm80xx: Updated common functions common for SPC and SPCv/ve
  [SCSI] pm80xx: Multiple inbound/outbound queue configuration
  [SCSI] pm80xx: Added SPCv/ve specific ids, variables and modify for SPC
  [SCSI] lpfc: fix up Kconfig dependencies
  [SCSI] Handle MLQUEUE busy response in scsi_send_eh_cmnd
  [SCSI] sd: change to auto suspend mode
  [SCSI] sd: use REQ_PM in sd's runtime suspend operation
  [SCSI] qla4xxx: Fix iocb_cnt calculation in qla4xxx_send_mbox_iocb()
  [SCSI] ufs: Correct the expected data transfersize
  ...
2013-05-11 15:24:22 -07:00
Linus Torvalds
ac4e01093f Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pull idle update from Len Brown:
 "Add support for new Haswell-ULT CPU idle power states"

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
  intel_idle: initial C8, C9, C10 support
  tools/power turbostat: display C8, C9, C10 residency
2013-05-11 15:23:17 -07:00
Linus Torvalds
c4cc75c332 Merge git://git.infradead.org/users/eparis/audit
Pull audit changes from Eric Paris:
 "Al used to send pull requests every couple of years but he told me to
  just start pushing them to you directly.

  Our touching outside of core audit code is pretty straight forward.  A
  couple of interface changes which hit net/.  A simple argument bug
  calling audit functions in namei.c and the removal of some assembly
  branch prediction code on ppc"

* git://git.infradead.org/users/eparis/audit: (31 commits)
  audit: fix message spacing printing auid
  Revert "audit: move kaudit thread start from auditd registration to kaudit init"
  audit: vfs: fix audit_inode call in O_CREAT case of do_last
  audit: Make testing for a valid loginuid explicit.
  audit: fix event coverage of AUDIT_ANOM_LINK
  audit: use spin_lock in audit_receive_msg to process tty logging
  audit: do not needlessly take a lock in tty_audit_exit
  audit: do not needlessly take a spinlock in copy_signal
  audit: add an option to control logging of passwords with pam_tty_audit
  audit: use spin_lock_irqsave/restore in audit tty code
  helper for some session id stuff
  audit: use a consistent audit helper to log lsm information
  audit: push loginuid and sessionid processing down
  audit: stop pushing loginid, uid, sessionid as arguments
  audit: remove the old depricated kernel interface
  audit: make validity checking generic
  audit: allow checking the type of audit message in the user filter
  audit: fix build break when AUDIT_DEBUG == 2
  audit: remove duplicate export of audit_enabled
  Audit: do not print error when LSMs disabled
  ...
2013-05-11 14:29:11 -07:00
Linus Torvalds
3644bc2ec7 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal
Pull stray syscall bits from Al Viro:
 "Several syscall-related commits that were missing from the original"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
  switch compat_sys_sysctl to COMPAT_SYSCALL_DEFINE
  unicore32: just use mmap_pgoff()...
  unify compat fanotify_mark(2), switch to COMPAT_SYSCALL_DEFINE
  x86, vm86: fix VM86 syscalls: use SYSCALL_DEFINEx(...)
2013-05-10 09:21:05 -07:00