If host fails to wakeup the firmware, we will trigger card reset
after 3 second timeout.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
200ms is the requirement to allow VDD1.1 and VDD1.8 to
drop to have proper reset.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Workqueue needs to be flushed early when removing card, otherwise
soft lockup issue may happen because main_process is triggered by
interrupt while card is being removed.
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This flag is never set but checked at two places. We will get rid of
this code.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support to get number of BA streams
supported information from FW. Some newer chips(e.g. 8897 series)
support 4 BA streams for TX; so driver should not disallow BA stream
setup just after 2 streams have been established.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for DMA alignment of 64 bytes for TX packets.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes memory corruption reported by community developer.
"Memory corruption occurs in mwifiex_ret_802_11_key_material_v1()
when a short command response is received without a key length
causing non initialised memory to be interpreted as the key
length resulting in a memcpy() overwriting the part of the
driver's private data structure beyond the key area."
For v1 key material API firmwares, there is no need to send
command to delete WEP key. WEP encryption/decryption is controlled
by mac_control command.
This patch avoids sending key material command in del_key case.
Reported-by: Martin Fuzzey <mfuzzey@parkeon.com>
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for the bcm43340 and bcm43341 wireless
chipsets. These two chipsets are identical from wireless parts
perspective. As such they use the same firmware image.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Rob Herring <rob.herring@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
[arend@broadcom.com: squash to single commit, remove 43341 chipid]
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds module parameter for auto deepsleep configuration.
By default, module_param is 0 and auto deep sleep is enabled.
If mwifiex driver is loaded with disable_auto_ds=1, deep sleep
configuration would not be downloaded to FW and FW would not enter
deepsleep upon initializing.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch saves sdio registers value before firmware dump,
this can be used to find out reason for FW dump.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support to dump driver information to a file
when firmware dump happens. This information can be used to
root casue FW crash.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mwifiex_debug_info also need be save to file when firmware dump happens.
Move its dump implementation function to commmon utilility file, thus it
can be reused in firmware dump function.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move mwifiex_pm_wakeup_card_complete handler to source file.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch add a new debugfs item histogram used for reporting
rx data packet statitics(rx rate, snr, noise floor, signal strenth)
to userspace.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch add receive beacon count and miss beacon count statistics
in debugfs getlog item.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch add provision to show TDLS peer table in debugfs file.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the driver gets beacon info containing a country IE from user-space
upon .start_ap() callback, it will enable regulatory 802.11d support.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use cfg80211 change_station to signal the completion of 802.1x
to firmware. This allows FW to take appropriate actions.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When user-space uses a valid ISO-3166-1 country code for its
regulatory domain selection, the driver will try to configure
the firmware to use the same.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When there is no room in the ring for rxbufpost an error is logged,
however this happens quite frequently and can be considered normal
and is certainly recoverable. This patch changes the erorr into
a normal msgbuf log.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When a device is configured for AP mode and it is configured for
WEP then the keys are plumbed first, followed by AP configuration.
During configuration a down command is given to the firmware which
will clear the configured keys. This patch reprograms the WEP keys
after AP has been brought up.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The source file chip.c contained some duplicate defines and
some unused ones. Removing them.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The physical addresses being used by pcie and msgbuf were using
a cast to long, which incorrectly caused it to limit the address
to 32bit. Now explicit u64 is used where needed.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* enhancements to the firmware debugging infrastructure
* support for 2 concurrent channel contexts
* fixes / cleanups in the rate control
* general cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gLE1
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2014-12-30' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* more work on d0i3 power state
* enhancements to the firmware debugging infrastructure
* support for 2 concurrent channel contexts
* fixes / cleanups in the rate control
* general cleanups
The patch "40a11ca mac80211: check if channels allow 80 MHz for VHT
probe requests" considered disabled channels as VHT enabled, and
mistakenly sent out probe-requests with the VHT IE.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Put the group names into the userspace API header file so that
userspace clients can use symbolic names from there instead of
hardcoding the actual names. This doesn't really change much,
but seems somewhat cleaner.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With the wiphy::features flag being used up this patch adds a
new field wiphy::ext_features. Considering extensibility this
new field is declared as a byte array. This extensible flag is
exposed to user-space by NL80211_ATTR_EXT_FEATURES.
Cc: Avinash Patil <patila@marvell.com>
Signed-off-by: Gautam (Gautam Kumar) Shukla <gautams@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The flag is no longer used (and hasn't been for a long time)
since trying to track authentication (and make decisions based
on state) was just causing issues all over - see commit
95de817b90.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit ca34e3b5c8.
It turns out that the p54 and cw2100 drivers assume that there's
tailroom even when they don't say they really need it. However,
there's currently no way for them to explicitly say they do need
it, so for now revert this.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=90331.
Cc: stable@vger.kernel.org
Fixes: ca34e3b5c8 ("mac80211: Fix accounting of the tailroom-needed counter")
Reported-by: Christopher Chavez <chrischavez@gmx.us>
Bisected-by: Larry Finger <Larry.Finger@lwfinger.net>
Debugged-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows 3160 / 7260 / 7265 / 7265D / 8000 devices to
use the latest version of the firmware.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Use only basic dwell time (10 ms for active scan and 110 for passive),
regardless of the number of the probes and the band, if it is
supported by the FW. The FW will add 3 ms for each probe sent and 10
ms for low band channels.
Add a TLV flag to indicate such support in FW.
This fix is needed to fix few bugs regarding scans that take too much time.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add a flag that enables match found notification to align with
FW API change.
Cc: <stable@vger.kernel.org> [3.17+]
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When tid_tspec was set to IWL_TID_NON_QOS (8) this led to an
out of bounds access to the tid_to_mac80211_ac array whose size
is 7. Fix this.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
commit 5c90422439
"iwlwifi: mvm: don't allow diversity if BT Coex / TT forbid it"
broke Rx with 2 chains for diversity.
This had an impact on throughput where we're using only a single
stream (11a/b/g APs, single stream APs, static SMPS).
Fixes: 5c90422439 ("iwlwifi: mvm: don't allow diversity if BT Coex / TT forbid it")
Cc: Stable <stable@vger.kernel.org> [3.16+]
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The trans cfg was not replaced for 7265-D cards. This led to a check of
the min-NVM version against a 7265-C card, causing very-old 7265-D cards
to operate incorrectly with the driver.
Fixes: 3fd0d3c170 ("iwlwifi: pcie: support 7265-D devices")
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Richard Cochran says:
====================
Fixing the "Time Counter fixes and improvements"
For this series I had only tested the build with ARCH=x86 and arm, but
others like sparc64, microblaze, powerpc, and s390 will fail because
they somehow don't indirectly include clocksource.h for the drivers in
question.
This series fixes the build issues reported by:
kbuild test robot <fengguang.wu@intel.com>
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The timecounter/cyclecounter code has moved, so users need the new include.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver uses the function, clocksource_khz2mult, and so it really must
include clocksource.h.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need for users of the timecounter/cyclecounter code to include
clocksource.h just for a single macro.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OVS development is moved to netdev mailing list. Update tree and
list in MAINTAINERS file.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* ath9k: enable Transmit Power Control (TPC) for ar9003 chips
* rtlwifi: cleanup and updates from the vendor driver
* rsi: fix memory leak related to firmware image
* ath: parameter fix for FCC DFS pattern
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJUpqFFAAoJEG4XJFUm622brwUH/iLBBtWvqbhFMKDlA9eUG0hD
z+LQkPtNR5gLYk11Qne7H8BjILDWgzdQcbyAUEpCnuplDThCDfj+8JB51gfNGpqU
pv9XwVO2Nf0afh4+hJBkBREI0vAJDod860AG+PV3E5G/WZZyt2MDxF9mk3IbvKVd
APR7cnUxsAltxjr7IWvPFY43wtbRJHbGM8EUVGkXDBaARaPipTJ7GqhwUyv45jCo
LRnW0VQ5njMZZD6DfteB9BiE+2GfZF9Ay4aOzRVJGc83NMHDBQxD7VSHVrBBgCt1
L+Ikz8O0UHG9TsoAGZqEcJ12o2iGWjVFm4TecEYsuhRA1fJmXJOispl/lnudZus=
=ZbEI
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2015-01-02' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Changes:
* ath9k: enable Transmit Power Control (TPC) for ar9003 chips
* rtlwifi: cleanup and updates from the vendor driver
* rsi: fix memory leak related to firmware image
* ath: parameter fix for FCC DFS pattern
Signed-off-by: David S. Miller <davem@davemloft.net>
Removes some functions that are not used anywhere:
enic_dev_enable2_done() enic_dev_enable2() enic_dev_deinit_done()
enic_dev_init_prov2() enic_vnic_dev_deinit()
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removes some functions that are not used anywhere:
Read_hfc32() Write_hfc32() Write_hfc16()
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
