The skcipher conversion for ARM missed the select on CRYPTO_SIMD,
causing build failures if SIMD was not otherwise enabled.
Fixes: da40e7a4ba ("crypto: aes-ce - Convert to skcipher")
Fixes: 211f41af53 ("crypto: aesbs - Convert to skcipher")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Currently the memory controller and master priorities drivers are
enabled in da850.dtsi. For boards for which there are no settings
defined, this makes these drivers emit error messages.
Disable the nodes in da850.dtsi and only enable them for da850-lcdk -
the only board that currently needs them.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Currently the mmc driver is polling the gpio to know if the
card was removed.
By using a gpio descriptor instead of the platform callbacks,
the driver will be able to register the gpio using the mmc core
APIs designed for this purpose.
This has the advantage that an irq will be registered, and
polling is no longer needed. Also, a dependency on platform
callbacks is removed for this board.
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
[nsekhar@ti.com: minor commit message edit]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Currently the mmc driver is polling the gpio to know if the
card was removed.
By using a gpio descriptor instead of the platform callbacks,
the driver will be able to register the gpio using the mmc core
APIs designed for this purpose.
This has the advantage that an irq will be registered, and
polling is no longer needed. Also, a dependency on platform
callbacks is removed for this board.
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
[nsekhar@ti.com: minor commit message edit]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Currently the mmc driver is polling the gpio to know if the
card was removed.
By using a gpio descriptor instead of the platform callbacks,
the driver will be able to register the gpio using the mmc core
APIs designed for this purpose.
This has the advantage that an irq will be registered, and
polling is no longer needed. Also, a dependency on platform
callbacks is removed for this board.
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
In order to avoid Linux generating a random mac address on every boot,
add an ethernet0 alias that will allow u-boot to patch the dtb with
the MAC address programmed into the EEPROM.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
udplite conflict is resolved by taking what 'net-next' did
which removed the backlog receive method assignment, since
it is no longer necessary.
Two entries were added to the non-priv ethtool operations
switch statement, one in 'net' and one in 'net-next, so
simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull ARM fix from Russell King:
"This resolves the ksyms issues by reverting the commit which
introduced the breakage"
There was what I consider to be a better fix, but it's late in the rc
game, so I'll take the revert.
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
Revert "arm: move exports to definitions"
The usual bunch of DT additions, but most notably:
- A31 DRM driver
- A31 audio codec
- WiFi for the A80-Based boards and the CHIP
- Support for the NextThing Co CHIP Pro (the first board with NAND
enabled)
- New board: NanoPi M1
-----BEGIN PGP SIGNATURE-----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=cln8
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.10-bis' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Pull "Allwinner DT additions for 4.10, bis" from Maxime Ripard:
The usual bunch of DT additions, but most notably:
- A31 DRM driver
- A31 audio codec
- WiFi for the A80-Based boards and the CHIP
- Support for the NextThing Co CHIP Pro (the first board with NAND
enabled)
- New board: NanoPi M1
* tag 'sunxi-dt-for-4.10-bis' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (41 commits)
ARM: dts: sun6i: hummingbird-a31: Enable display output through VGA bridge
ARM: dts: sun5i: Add touchscreen node to reference-design-tablet.dtsi
ARM: sunxi: Add the missing clocks to the pinctrl nodes
ARM: dts: sun7i: bananapi-m1-plus: Enable USB OTG
ARM: dts: sun7i: bananapi-m1-plus: Add PMIC regulators
ARM: dts: sun7i: bananapi-m1-plus: Enable USB PHY for USB host support
ARM: sun8i: sina33: Enable USB gadget
ARM: dts: sun8i: reference-design-tablet: ldo_io1 is vcc-touchscreen
ARM: dts: sun8i: replace enable-sdio-wakeup with wakeup-source for BananaPi M1+
ARM: gr8: evb: Add i2s codec
ARM: dts: sun6i: sina31s: Enable internal audio codec
ARM: dts: sun6i: hummingbird: Enable internal audio codec
ARM: dts: sun6i: Add audio codec device node
ARM: gr8: evb: Enable SPDIF
ARM: dts: sun8i: Add SPI controller node in H3
ARM: dts: sun8i: Add SPI pinctrl node in H3
ARM: dts: sun8i: Add dts file for NanoPi M1 SBC
ARM: dts: sun8i: Use the common file in NanoPi NEO SBC
ARM: dts: sun8i: Add common dtsi file for NanoPi SBCs
ARM: dts: sun9i: cubieboard4: Enable AP6330 WiFi
...
remove legacy support of orion5x ls-chl
-----BEGIN PGP SIGNATURE-----
iGoEABECACoFAlgwDyEjHGdyZWdvcnkuY2xlbWVudEBmcmVlLWVsZWN0cm9ucy5j
b20ACgkQCwYYjhRyO9XvjwCffCGDTTvUAn1iBzbI+ijo3Zx1+iwAnAt3aa2pXiSI
Aya4ElGbmbfODIbo
=cSoP
-----END PGP SIGNATURE-----
Merge tag 'mvebu-soc-4.10-1' of git://git.infradead.org/linux-mvebu into next/soc
Pull "mvebu soc for 4.10 (part 1)" from Gregory CLEMENT:
remove legacy support of orion5x ls-chl
* tag 'mvebu-soc-4.10-1' of git://git.infradead.org/linux-mvebu:
ARM: orion5x: remove legacy support of ls-chl
Add missing pinmux declaration for netgear NASes
Fix i2c compatible string for netgear NASes
Fix on a wrong comment about PLL frequency
Fix spelling mistake of the manufacturer's name of the Topkick
Add dt support for the orion5x ls-chl Linkstation device
First step of fixing DTC warning for Armada 370, 375 and XP
-----BEGIN PGP SIGNATURE-----
iGoEABECACoFAlgwC9wjHGdyZWdvcnkuY2xlbWVudEBmcmVlLWVsZWN0cm9ucy5j
b20ACgkQCwYYjhRyO9VAsgCfdqwKz5V7XP/xfkIUxoykhtrLL4QAoJlAAwV+UG2U
Gbvc3BMoymvienDl
=06ld
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.10-1' of git://git.infradead.org/linux-mvebu into next/dt
Pull "mvebu dt for 4.10 (part 1)" from Gregory CLEMENT:
Add missing pinmux declaration for netgear NASes
Fix i2c compatible string for netgear NASes
Fix on a wrong comment about PLL frequency
Fix spelling mistake of the manufacturer's name of the Topkick
Add dt support for the orion5x ls-chl Linkstation device
First step of fixing DTC warning for Armada 370, 375 and XP
* tag 'mvebu-dt-4.10-1' of git://git.infradead.org/linux-mvebu: (30 commits)
ARM: dts: armada-375: Fixup ethernet child DT warning
ARM: dts: armada-375: Fixup memory DT warning
ARM: dts: armada-375: Remove skeleton.dtsi
ARM: dts: armada-375: Fixup pinctrl DT warnings
ARM: dts: armada-375: Fixup pcie DT warnings
ARM: dts: armada-375: Fixup mdio DT warning
ARM: dts: armada-375: Use the node labels
ARM: dts: armada-375: Add node labels
ARM: dts: armada-370-xp: Fixup regulator DT warning
ARM: dts: armada-370-xp: Remove button address and fixup names
ARM: dts: armada-370-xp: Remove address from dsa unit name
ARM: dts: armada-370-xp: Fixup memory DT warning
ARM: dts: armada-370-xp: Fixup l2-cache DT warning
ARM: dts: armada-370-xp: Remove skeleton.dtsi
ARM: dts: armada-370: Fixup pcie DT warnings
ARM: dts: armada-xp: Fixup pcie DT warnings
ARM: dts: armada-370-xp: Fixup mdio DT warning
ARM: dts: armada-370-xp: Use the node labels
ARM: dts: armada-370-xp: add node labels
ARM: dts: armada-370-xp: move the cpurst node in the common file
...
from http://lkml.kernel.org/r/20161021085848.1754-1-narmstrong@baylibre.com
Changes since v1 Pull Request at : http://lkml.kernel.org/r/1305c61f-b1ef-7caf-7788-67e2b907e873@baylibre.com
- Clarify copyright dates in commit message
- Remove linux/arch/... lines from the top of the files
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Xa6Z
-----END PGP SIGNATURE-----
Merge tag 'oxnas-arm-soc-for-4.10-v2' of https://github.com/OXNAS/linux into next/soc
Pull "ARM: OXNAS SoC updates for 4.10" from Neil Armstrong:
- Add SMP support for the Oxford Semiconductor OX820 SoC
from http://lkml.kernel.org/r/20161021085848.1754-1-narmstrong@baylibre.com
Changes since v1 Pull Request at : http://lkml.kernel.org/r/1305c61f-b1ef-7caf-7788-67e2b907e873@baylibre.com
- Clarify copyright dates in commit message
- Remove linux/arch/... lines from the top of the files
* tag 'oxnas-arm-soc-for-4.10-v2' of https://github.com/OXNAS/linux:
ARM: oxnas: Add OX820 config and makefile entry
ARM: oxnas: Add OX820 SMP support
Add PCIe support to the ARTPEC-6 SoC. This uses the existing
pcie-artpec6 driver.
So, all that is needed is device tree entries in the DTS.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Jesper Nilsson <jespern@axis.com>
Since the ARTPEC-6 machine port already uses syscon,
MACH_ARTPEC6 should select MFD_SYSCON.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Jesper Nilsson <jespern@axis.com>
Merge "IDE to PATA change in ARM defconfigs from Bartlomiej Zolnierkiewicz:
On Monday, October 31, 2016 07:14:13 PM Bartlomiej Zolnierkiewicz wrote:
> On Monday, October 31, 2016 03:46:22 PM Russell King - ARM Linux wrote:
> > On Wed, Oct 26, 2016 at 07:01:12PM +0200, Bartlomiej Zolnierkiewicz wrote:
> > > On Wednesday, July 13, 2016 04:37:31 PM Arnd Bergmann wrote:
> > > > I'd be fine with just getting a pull request with all the patches that
> > > > had no negative feedback and that were not already applied (if any).
> > >
> > > Here it is (sorry for taking so long).
> >
> > I've just been digging in the dmesg logs from when I was using the
> > Assabet+Neponset as my firewall, and it was having to use the IDE
> > ide-cs driver rather than the pata pcmcia driver.
> >
> > I don't recall whether the pata pcmcia driver was a problem or not,
> > as the PCMCIA interface can't cope with _any_ 32-bit accesses. I
> > think PATA tries to use the "highest" possible access size by
> > default...
>
> It doesn't actually - it defaults to 16-bits for PIO data access and
> you must explicitly enable 32-bits using ATA_PFLAG_PIO32 port flag
> (pata_pcmcia doesn't set it so it should be okay). Also taskfile
> registers are accessed using 8-bits access by default transport
> functions (which are used by pata_pcmcia).
Please also note that:
- assebet_defconfig currently doesn't even enable ide-cs
(CONFIG_BLK_DEV_IDECS) in the mainline kernel
- neponset_defconfig doesn't even enable IDE (CONFIG_IDE)
in the mainline kernel
so there is no risk of breaking anything..
* 'v4.9-rc2-arm-configs-pata' of https://github.com/bzolnier/linux:
arm: spitz_defconfig: convert to use libata PATA drivers
arm: s3c2410_defconfig: convert to use libata PATA drivers
arm: netwinder_defconfig: convert to use libata PATA drivers
arm: jornada720_defconfig: convert to use libata PATA drivers
arm: ixp4xx_defconfig: convert to use libata PATA drivers
arm: h3600_defconfig: convert to use libata PATA drivers
arm: corgi_defconfig: convert to use libata PATA drivers
arm: am200epdkit_defconfig: convert to use libata PATA drivers
arm: omap1_defconfig: convert to use libata PATA drivers
arm: collie_defconfig: convert to use libata PATA drivers
arm: shannon_defconfig: disable IDE subsystem
arm: mainstone_defconfig: disable IDE subsystem
arm: lart_defconfig: disable IDE subsystem
arm: cerfcube_defconfig: disable IDE subsystem
arm: badge4_defconfig: disable IDE subsystem
arm: assabet_defconfig: disable IDE subsystem
The I2C nodes are missing #address-cells and #size-cells.
This is causing warning at device tree compilation when
some I2C device sub-nodes are defined.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=nQve
-----END PGP SIGNATURE-----
Merge tag 'sti-dt-for-v4.9-rc-round2' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti into fixes
Pull "STi DT fix" from Patrice Chotard:
The I2C nodes are missing #address-cells and #size-cells.
This is causing warning at device tree compilation when
some I2C device sub-nodes are defined.
* tag 'sti-dt-for-v4.9-rc-round2' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti:
ARM: dts: STiH407-family: fix i2c nodes
A renaming of the GR8 DTSI and DTS to make it explicitly part of the sun5i
family.
-----BEGIN PGP SIGNATURE-----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=Mw6R
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.9-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Pull "Allwinner fixes for 4.9, second iteration" from Maxime Ripard:
A renaming of the GR8 DTSI and DTS to make it explicitly part of the sun5i
family.
* tag 'sunxi-fixes-for-4.9-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: gr8: Rename the DTSI and relevant DTS
This machine is an open hardware router by cz.nic driven by a
Marvell Armada 385.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Tomas Hlavacek <tmshlvck@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch fixes the following DTC warnings with W=1:
Warning (unit_address_vs_reg): Node /regulators/regulator@0 has a unit
name, but no reg property
Warning (unit_address_vs_reg): Node /regulators/regulator@1 has a unit
name, but no reg property
Warning (unit_address_vs_reg): Node /regulators/regulator@2 has a unit
name, but no reg property
Warning (unit_address_vs_reg): Node /regulators/regulator@3 has a unit
name, but no reg property
Warning (unit_address_vs_reg): Node /regulators/regulator@4 has a unit
name, but no reg property
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Add xo entry to sdhc clock node on all qcom platforms.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add a device node for the Product Register, which provides SoC product
and revision information.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Product Register, which provides SoC product
and revision information.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Product Register, which provides SoC product
and revision information.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Product Register, which provides SoC product
and revision information.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Product Register, which provides SoC product
and revision information.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Product Register, which provides SoC product
and revision information.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Product Register, which provides SoC product
and revision information.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the SK-RZG1E board dependent part of the Ether device node.
Enable DHCP and NFS root for the kernel booting.
Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial device tree for the R8A7745 SoC based SK-RZG1E board.
The board has 1 debug serial port (SCIF2); include support for it,
so that the serial console can work.
Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the IRQC interrupt controller in the R8A7745 device tree.
Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A7745 part of the Ether device node.
Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe [H]SCIF{|A|B} ports in the R8A7745 device tree.
Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
[simon: consistently use tabs for indentation]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe SYS-DMAC0/1 in the R8A7745 device tree.
Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The initial R8A7745 SoC device tree including CPU0, GIC, timer, SYSC, RST,
CPG, and the required clock descriptions.
Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the SK-RZG1M board dependent part of the Ether device node.
Enable DHCP and NFS root for the kernel booting.
Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial device tree for the R8A7743 SoC based SK-RZG1M board.
The board has one debug serial port (SCIF0); include support for it, so
that the serial console can work.
Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the IRQC interrupt controller in the R8A7743 device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A7743 part of the Ether device node.
Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe [H]SCIF{|A|B} ports in the R8A7743 device tree.
Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
[simon: consistently use tabs for indentation]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe SYS-DMAC0/1 in the R8A7743 device tree.
Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The initial R8A7743 SoC device tree including CPU0, GIC, timer, SYSC, RST,
CPG, and the required clock descriptions.
Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
And the sd-uhs-sdr104 property to SDHI0.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
And the sd-uhs-sdr104 property to SDHI0.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Add the sd-uhs-sdr104 property to SDHI0.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Make it possible to fallback to GPIO for I2C4 on the EXIO-B connector.
This is based on reference work for the I2C0 core of the lager/r8a7790
by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[wsa: rebased and fixed aliases]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Make it possible to fallback to GPIO for I2C1 on the EXIO-C connector.
This is based on reference work for the I2C0 core of the lager/r8a7790
by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[wsa: rebased and fixed aliases]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Make it possible to select which I2C1 IP core you want to run on the
EXIO-A connector.
This is based on reference work for the I2C0 core of the lager board
by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[wsa: rebased and fixed aliases]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
The rename from i2cexio to i2cexio0 is in preparation for adding
i2cexio1 which will use the demuxer for IIC1/I2C1.
The reindexing from i2c8 to i2c10 is to allow space for grouping of
additional GPIO buses to be added by follow-up patches to support demuxing
of other i2c buses.
Also note that fallback to GPIO is not provided by the hardware for IIC0/I2C0.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[wsa: rebased, fixed alias and removed typo in commit message]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
The parent clock of the HSUSB clock is the HP clock, not the MP clock.
Fixes: c7bab9f929 ("ARM: shmobile: r8a7794: Add USB clocks to device tree")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update the PFC pin groups and function names of DU interface for
r8a7794 ALT board.
The currently specified pin groups and function names prevented PFC and
DU interfaces from being correctly configured:
sh-pfc e6060000.pin-controller: function 'du' not supported
sh-pfc e6060000.pin-controller: invalid function du in map table
sh-pfc e6060000.pin-controller: function 'du' not supported
sh-pfc e6060000.pin-controller: invalid function du in map table
sh-pfc e6060000.pin-controller: function 'du' not supported
sh-pfc e6060000.pin-controller: invalid function du in map table
sh-pfc e6060000.pin-controller: function 'du' not supported
sh-pfc e6060000.pin-controller: invalid function du in map table
rcar-du: probe of feb00000.display failed with error -22
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Identify the SoC type and revision, and register this information with
the SoC bus, so it is available under /sys/devices/soc0/, and can be
checked where needed using soc_device_match().
Identification is done using the Product Register or Common Chip Code
Register, as declared in DT (PRR only for now), or using a hardcoded
fallback if missing.
Example:
Detected Renesas R-Car Gen2 r8a7791 ES1.0
...
# cat /sys/devices/soc0/{machine,family,soc_id,revision}
Koelsch
R-Car Gen2
r8a7791
ES1.0
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Odroid XU3/4 didn't need to use the cd-gpios for detecting card.
Because host controller has the CDETECT register through SDx_CDN line.
Host controller can know whether card is inserted or not with this
register.
When I have checked the Odroid XU3/4, they are using CDETECT register
(not using exteranl cd-gpio).
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
devicetree binding for stmmac states:
- compatible: Should be "snps,dwmac-<ip_version>", "snps,dwmac"
For backwards compatibility: "st,spear600-gmac" is also supported.
No functional change intended.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The AM571x-IDK board is a board based on TI's AM5718 SOC
which has a single core 1.5GHz A15 processor. This board is a
development platform for the Industrial market with:
- 1GB of DDR3L
- Dual 1Gbps Ethernet
- HDMI,
- PRU-ICSS
- uSD
- 16GB eMMC
- CAN
- RS-485
- PCIe
- USB3.0
- Video Input Port
- Industrial IO port and expansion connector
The link to the data sheet and TRM can be found here:
http://www.ti.com/product/AM5718
Initial support is only for basic peripherals.
Signed-off-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
phy-phandle is now a preferred method to reference a PHY device.
Especially in regards to cpsw it enables PHY specific settings like
max-speed etc. being specified in DTS.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The PMICs have POWERHOLD set by default which prevents PMIC shutdown
even on DEV_CTRL On bit set to 0 as the Powerhold has higher priority.
So to enable pmic power off this property lets one over ride the default
value and enable pmic power off.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The PMICs have POWERHOLD set by default which prevents PMIC shutdown
even on DEV_CTRL On bit set to 0 as the Powerhold has higher priority.
So to enable pmic power off this property lets one over ride the default
value and enable pmic power off.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
While the clk lookup table is making reference to "ohci"
other subsystems (such as phy) are trying to match "ohci.0"
Since there is a single ohci instance, instead of changing
the clk name, change the dev id to -1, and add the "-da8xx"
postfix to match the driver name that will also be changed
in a subsequent patch.
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This reverts commit 4dd1837d75.
Moving the exports for assembly code into the assembly files breaks
KSYM trimming, but also breaks modversions.
While fixing the KSYM trimming is trivial, fixing modversions brings
us to a technically worse position that we had prior to the above
change:
- We end up with the prototype definitions divorsed from everything
else, which means that adding or removing assembly level ksyms
become more fragile:
* if adding a new assembly ksyms export, a missed prototype in
asm-prototypes.h results in a successful build if no module in
the selected configuration makes use of the symbol.
* when removing a ksyms export, asm-prototypes.h will get forgotten,
with armksyms.c, you'll get a build error if you forget to touch
the file.
- We end up with the same amount of include files and prototypes,
they're just in a header file instead of a .c file with their
exports.
As for lines of code, we don't get much of a size reduction:
(original commit)
47 files changed, 131 insertions(+), 208 deletions(-)
(fix for ksyms trimming)
7 files changed, 18 insertions(+), 5 deletions(-)
(two fixes for modversions)
1 file changed, 34 insertions(+)
3 files changed, 7 insertions(+), 2 deletions(-)
which results in a net total of only 25 lines deleted.
As there does not seem to be much benefit from this change of approach,
revert the change.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Refactor the oxnas Kconfig entries among the OX810SE and OX820 configs,
and add the files to support the OX820 SMP feature.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Oxford Semiconductor OX820 is a ARM11MPcore based SoC sharing some
features with the OX810 earlier SoC.
This patch adds the core to wake up the second core.
Clarifications about Copyrights dates :
- hotplug.c was taken from an old versatile code by Ma Haijun and left verbatim
- headsmp.S was taken from an old versatile code and adapted by Ma Haijun
- platsmp.c is a mix from versatile code, Ma Haijun code and my code for DT
Hence the 2002/2003 ARM Coryrights and 2013 Ma Haijun Copyrights.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The I2C nodes are missing #address-cells and #size-cells. This is
causing warning at device tree compilation when some I2C device
sub-nodes are defined.
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Install the callbacks via the state machine and let the core invoke
the callbacks on the already online CPUs.
smp_call_function_single() has been removed because the function is already
invoked on the target CPU.
[ tglx: Added protection agaist hotplug back according to discussion with Will ]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: rt@linuxtronix.de
Cc: Will Deacon <will.deacon@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/20161117183541.8588-16-bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable the davinci ohci driver as a module for usb
tested with the omap138-lcdk board.
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The Hummingbird A31 board has a VGA DAC which converts RGB output
from the LCD interface to VGA analog signals.
Add nodes for the VGA DAC, its power supply, and enable this part
of the display pipeline.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Just like on sun8i all sun5i tablets use the same interrupt and power
gpios for their touchscreens. I've checked all known a13 fex files and
only the UTOO P66 uses a different gpio for the interrupt.
Add a touchscreen node to sun5i-reference-design-tablet.dtsi, which
fills in the necessary gpios to avoid duplication in the tablet dts files,
just like we do in sun8i-reference-design-tablet.dtsi.
This will make future patches adding touchscreen nodes to a13 tablets
simpler.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The pin controllers also use the two oscillators for debouncing. Add them
to the DTs.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The Bananapi M1+ supports USB OTG, with the PMIC doing VBUS sensing.
Enable the USB OTG related functions.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Bananapi M1+, like other Allwinner A20 based boards, uses the
AXP209 PMIC to supply its power.
Add the AXP209 regulators.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The 2 USB host ports are directly tied to the 2 USB hosts in the SoC.
The 2 host pairs were already enabled, but the USB PHY wasn't.
VBUS on the 2 ports are always on.
Enable the USB PHY.
Fixes: 04c85ecad3 ("ARM: dts: sun7i: Add dts file for Bananapi M1 Plus
board")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The micro-USB on the SinA33 has a somewhat interesting design in the sense
that it has a micro USB connector, but the VBUS is (supposed to be)
controlled through an (unpopulated) jumper.
Obviously, that doesn't work really well, and only the peripheral mode
really works. Still enable it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On some Q8 and other tablets ldo_io1 is used as vcc-touchscreen,
config at as such in sun8i-reference-design-tablet.dtsi.
Note that it will only be enabled when it us actually referenced by
a foo-supply property in the touchscreen node, so for tablets which
do not use ldo_io1 as vcc-touchscreen, it will be disabled.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Though the mmc core driver will continue to support the legacy
"enable-sdio-wakeup" property to enable SDIO as the wakeup source,
"wakeup-source" is the new standard binding.
This patch replaces the legacy "enable-sdio-wakeup" with the unified
"wakeup-source" property in order to avoid any further copy-paste
duplication.
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The GR8-EVB comes with a wm8978 codec connected to the i2s bus.
Add a card in order to have it working
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The SinA31s routes the SoC's LINEOUT pins to a line out jack, and MIC1
to a microphone jack, with MBIAS providing phantom power.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Hummingbird A31 has headset and line in audio jacks and an onboard
mic routed to the pins for the SoC's internal codec. The line out pins
are routed to an onboard speaker amp, whose output is available on a
pin header.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A31 SoC includes the Allwinner audio codec, capable of 24-bit
playback up to 192 kHz and 24-bit capture up to 48 kHz.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The GR8-EVB has a SPDIF out connector. Enable it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
H3 SPI subsystem is almost same as A31 SPI except buffer size, so those
DT properties are reusable.
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
H3 supports two SPI controllers. Four pins (MOSI, MISO, SCLK, SS) are
configured through the pinctrl subsystem.
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
NanoPi M1 is the Allwinner H3 based board.
This patch enables UART for debug console, LEDs, GPIO key switch, 3 USB
host ports, a micro SD slot and related power and pin controls by using
NanoPi common dtsi file.
Cc: James Pettigrew <james@innovum.com.au>
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
NanoPi common dtsi supports all components of NEO SBC, so just include it.
Cc: James Pettigrew <james@innovum.com.au>
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch provides a common file for NanoPi M1 and Neo SBC.
Those have common features below.
* UART0
* 2 LEDs
* USB host (EHCI3, OHCI3) and PHY
* MicroSD
* GPIO key switch
Cc: James Pettigrew <james@innovum.com.au>
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The board has a Ampak AP6330 WiFi/BT/FM module. Inside it is a Broadcom
BCM4330 WiFi/BT/FM combo IC. The WiFi portion is connected to mmc1, with
the enabling pin connected to PL2. The AC100 RTC provides a low power
clock signal.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The board has a Ampak AP6330 WiFi/BT/FM module. Inside it is a Broadcom
BCM4330 WiFi/BT/FM combo IC. The WiFi portion is connected to mmc1, with
the enabling pin connected to PL2. The AC100 RTC provides a low power
clock signal.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the A80, mmc1 is available on pingroup G. Designs mostly use this
to connect to an SDIO WiFi chip.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The I2C1 and SPI2 buses are exposed on the CHIP headers, and are not
explicitly dedicated to anything.
Add them to the DTS with the muxing already set, but keep them disabled.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Some boards use the LCD in RGB565. Enable the pin muxing option.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
All the sun5i have the SPI2 pins exposed on the PE bank. Add them to the
DT.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The SPI2 pins on the sun5i PB bank are only available on the A10s. Rename
the A10s only bank so that it doesn't confuse people on the other SoCs
whose indexing would start at b.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The CHIP uses a 1-Wire bus to discover the DIPs. Enable the bus in the DT.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The WiFi chip is powered through a GPIO and two regulators in parallel.
Since that case is not supported yet, just set them as always on before we
rework the regulator framework to deal with those.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The CHIP Pro is a small embeddable board. It features a GR8, an AXP209
PMIC, a 512MB SLC NAND and a WiFi/BT chip.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The UART3 pins were missing from the DTSI. Add them.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The UART2 pins were missing from the DTSI. Add them.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The PWM controller has two different channels, but only the first pin was
exposed in the DTSI. Add the other one.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
There was a dumb copy and paste mistake here, fix it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The GR8 has access to the UART3 controller, which was missing in the
DTSI. Add it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The LCD0 controller on the A31 can do RGB output up to 8 bits per
channel. Add the pins for RGB888 output.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A31 has 2 parallel display pipelines, which can be intermixed.
However the driver currently only supports one of them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
sun7i-a20-olimex-som-evb.dts doesn't contain cpu-supply needed for
voltage-scaling with cpufreq-dt so define it.
The default voltages are defined in sun7i-a20.dtsi.
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we have support for the VGA bridges using our DRM driver, enable
the display engine for the Olimex A13-Olinuxino.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The pinmux setting nodes for the A31 were added out of alphabetical
order. Sort them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviews have found that sun5i was a better prefix after all for the GR8.
Rename the relevant device trees before it's too late.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This is good for consistency even if there is no difference in compiled
code. LTO might rely on this eventually. No need to preserve the extern
attribute as it is the default with function prototypes.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a sysfs cpu_capacity attribute with which it is possible to read and
write (thus over-writing default values) CPUs capacity. This might be
useful in situations where values needs changing after boot.
The new attribute shows up as:
/sys/devices/system/cpu/cpu*/cpu_capacity
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With the introduction of cpu capacity-dmips-mhz bindings, CPU capacities
can now be calculated from values extracted from DT and information
coming from cpufreq. Add parsing of DT information at boot time, and
complement it with cpufreq information. We keep code that can produce
same information, based on different DT properties and hard-coded
values, as fall-back for backward compatibility.
Caveat: the information provided by this patch will start to be used in
the future. We need to #define arch_scale_cpu_capacity to something
provided in arch, so that scheduler's default implementation (which gets
used if arch_scale_cpu_capacity is not defined) is overwritten.
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Acked-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The polarity of the card detect pin is inverted.
Change it to reflect the right polarity for the board
which is ACTIVE_LOW.
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
cleanups, GPIO line naming, and the node for the new thermal driver.
-----BEGIN PGP SIGNATURE-----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=CBTE
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=pDtt
-----END PGP SIGNATURE-----
Merge tag 'bcm2835-dt-next-2016-11-18' into devicetree/next
This pull request brings in DT changes for BCM2835: pinctrl setup
cleanups, GPIO line naming, and the node for the new thermal driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The Kconfig and file naming for the PM8xxx driver is totally
confusing:
- Kconfig options MFD_PM8XXX and MFD_PM8921_CORE, some in-kernel
users depending on or selecting either at random.
- A driver file named pm8921-core.c even if it is indeed
used by the whole PM8xxx family of chips.
- An irqchip named pm8xxx since it was (I guess) realized that
the driver was generic for all pm8xxx PMICs.
As I may want to add support for PM8901 this is starting to get
really messy. Fix this situation by:
- Remove the MFD_PM8921_CORE symbol and rely solely on MFD_PM8XXX
and convert all users, including LEDs Kconfig and ARM defconfigs
for qcom and multi_v7 to use that single symbol.
- Renaming the driver to qcom-pm8xxx.c to fit along the two
other qcom* prefixed drivers.
- Rename functions withing the driver from 8921 to 8xxx to
indicate it is generic.
- Just drop the =m config from the pxa_defconfig, I have no clue
why it is even there, it is not a Qualcomm platform. (Possibly
older Kconfig noise from saveconfig.)
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Pull ARM fixes from Russell King:
"A few more ARM fixes:
- the assembly backtrace code suffers problems with the new printk()
implementation which assumes that kernel messages without KERN_CONT
should have newlines inserted between them. Fix this.
- fix a section naming error - ".init.text" rather than ".text.init"
- preallocate DMA debug memory at core_initcall() time rather than
fs_initcall(), as we have some core drivers that need to use DMA
mapping - and that triggers a kernel warning from the DMA debug
code.
- fix XIP kernels after the ro_after_init changes made this data
permanently read-only"
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: Fix XIP kernels
ARM: 8628/1: dma-mapping: preallocate DMA-debug hash tables in core_initcall
ARM: 8624/1: proc-v7m.S: fix init section name
ARM: fix backtrace
This enables the usb otg controller for the lcdk board.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This adds the device tree node for the usb otg
controller present in the da850 family of SoC's.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Currently, suspend/resume support is only available on da850 platforms,
and the platform PM code has dependencies on da850 functions. However,
CONFIG_SUSPEND might be enabled even when da850 support is not, causing
build failure:
arch/arm/mach-davinci/built-in.o: In function `davinci_pm_init':
pm_domain.c:(.init.text+0x1fb8): undefined reference to `da8xx_get_mem_ctlr'
pm_domain.c:(.init.text+0x20b0): undefined reference to `da8xx_syscfg1_base'
Fix this by only building the PM core when da850 is enabled.
Reported-by: Sekhar Nori <nsekhar@ti.com>
Fixes: aa9aa1ec2d ("ARM: davinci: PM: rework init, remove platform device")
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Child of mvpp2 ethernet do not have a reg property so the unit name
should not contain an address: remove them.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e141 arm64: dts: kill skeleton.dtsi").
These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
As it was previously done for kirkwood and for aramda 370/XP, this adds
missing node labels to Armada 375 and SoC specific nodes to allow to
reference them more easily.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The gpio-key nodes do not have a reg property, so remove the address from
the unit name.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The dsa node does not have a reg property, so remove the address from the
unit name.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
l2-cache which is either an aurora-outer-cache or an aurora-system-cache
has a reg property so the unit name should contain an address.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e141 arm64: dts: kill skeleton.dtsi").
These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
PCIe has a ranges property, so the unit name should contain an address.
Take the opportunity to use the node label instead of the full name.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
PCIe has a range property, so the unit name should contain an address.
Take the opportunity to use the node label instead of the full name.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
MDIO has a reg property so the unit name should contain an address.
Take the opportunity to use the node label instead of the full name.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Use the node label when possible. As a result it flattens the device tree
and it makes more visible the IP blocks specific to each SoC variant.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
As it was previously done for kirkwood, this adds missing node labels to
Armada 370 and XP common and SoC specific nodes to allow to reference
them more easily.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
