Redhat Bugzilla: Bug 727875 - TCO_EN bit is disabled by TCO driver
The previous patch breaks reset watchdog behaviour on the older hardware.
It is therefor better to make sure that the behaviour for older hardware (<=ICH5 or
6300ESB) is preserved and that the behaviour for newer hardware is changed.
We therefor use the iTCO_version to see if we need the clearing of the SMI_TCO_EN
bit in the SMI_EN register.
So the new behaviour becomes:
turn_SMI_watchdog_clear_off=0 -> Do not turn off SMI clearing watchdog.
turn_SMI_watchdog_clear_off=1 -> Turn off SMI clearing watchdog when iTCO_version=1
(ICHO till ICH5 + 6300ESB only)
turn_SMI_watchdog_clear_off=2 -> Turn off SMI clearing watchdog.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch makes use of the set_memory_x() kernel API in order
to make necessary BIOS calls to source NMIs.
This is needed for SLES11 SP2 and the latest upstream kernel as it appears
the NX Execute Disable has grown in its control.
Signed-off by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off by: Wim Van Sebroeck <wim@iguana.be>
Cc: stable@kernel.org
The AMBA ID table is marked as __initdata, yet it is referenced by the
driver struct which is not. This causes a (somewhat unhelpful) section
mismatch warning:
WARNING: drivers/watchdog/sp805_wdt.o(.data+0x4c): Section mismatch in
reference from the variable sp805_wdt_driver to the (unknown
reference) .init.data:(unknown)
Fix this by removing the annotation.
Signed-off-by: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The state holders used in the PM path of the drivers report as
unused variables when compiling without CONFIG_PM so let's
move them inside CONFIG_PM.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Looks like a typo creeped in, and driver prints
s3c2410-wdt s3c2410-wdt: watchdog active, reset abled, irq abled
instead of
s3c2410-wdt s3c2410-wdt: watchdog active, reset enabled, irq enabled
Also it may completely disinform about irq status, as it prints
"irq enabled" when S3C2410_WTCON_INTEN is in fact 0.
Fix it.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Tested-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Remove the driver (that was added in v2.6.32) since the architecture
has never been merged into mainline.
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
Fairly large code churn but not much doing with that and the overall
result is a definite win.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Make this driver a user of the watchdog framework and remove now
centrally handled parts. Tested on a mini2440.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Redhat Bugzilla: Bug 727875 - TCO_EN bit is disabled by TCO driver
Jiri Slaby: 28d41f53f broke temperature sensors on a ICH10 chipset
The iTCO_wdt driver disables the SMI. This breaks good working of newer hardware.
The disabling of the SMI by the TCO logic dates back from the i810-tco driver
from Nils Faerber (around 28 July 2000). The reason for this was that some BIOSes
install handlers reset or disable the watchdog timer instead of resetting the system.
The trick to fix this was to disable the SMI (by clearing the SMI_TCO_EN bit of the
SMI_EN register) to prevent this from happening.
This however has strange effects on newer hardware. So we are in a situation that
a fix for broken old hardware affects newer hardware.
The correct solution is to make this fix an option (with the new module parameter:
turn_SMI_watchdog_clear_off) so that the default behaviour is the unfixed version.
the next patch will be to move this in the start and stop functions of the driver
and to add a new module parameter for the global_smi_en bit and to get rid of the
vendor_support code.
This fix can have an effect on old (typical ICH & ICH2 chipsets) motherboards that
have a broken BIOS implementation concerning TCO logic. In these case the module
parameter turn_SMI_watchdog_clear_off=1 will need to be added.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add WDIOC_GETTIMELEFT ioctl allowing you to check how much time is left
on the watchdog counter before a reset occurs.
Signed-off-by: Greg Lee <glee [at] swspec.com>
Signed-off-by: Padraig Brady <P@draigbrady.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@google.com>
This flag is a NOOP and can be removed now.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This is to exclude it from force threading to allow RT patch set to work.
The watchdog timers are per-CPU and the addresses of register that reset
the timer are calculated based on the current CPU. Therefore we cannot
allow it to run on a thread on a different CPU. Also we only do a
single register write, which is much faster than scheduling a handler
thread.
And while on this line remove IRQF_DISABLED as this flag is a NOP.
Signed-off-by: Venkat Subbiah<venkat.subbiah@cavium.com>
Acked-by: David Daney<david.daney@cavium.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
* 'for-linus' of git://github.com/richardweinberger/linux: (90 commits)
um: fix ubd cow size
um: Fix kmalloc argument order in um/vdso/vma.c
um: switch to use of drivers/Kconfig
UserModeLinux-HOWTO.txt: fix a typo
UserModeLinux-HOWTO.txt: remove ^H characters
um: we need sys/user.h only on i386
um: merge delay_{32,64}.c
um: distribute exports to where exported stuff is defined
um: kill system-um.h
um: generic ftrace.h will do...
um: segment.h is x86-only and needed only there
um: asm/pda.h is not needed anymore
um: hw_irq.h can go generic as well
um: switch to generic-y
um: clean Kconfig up a bit
um: a couple of missing dependencies...
um: kill useless argument of free_chan() and free_one_chan()
um: unify ptrace_user.h
um: unify KSTK_...
um: fix gcov build breakage
...
* kill duplicates with drivers/char/Kconfig
* take watchdog one into drivers/watchdog/Kconfig
* take mmapper to arch/um/Kconfig.um
* rename Kconfig.char menu to "UML Character Devices"
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
This is a module and so needs module.h so that it will still build
once the implicit presence of module.h is removed.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (121 commits)
perf symbols: Increase symbol KSYM_NAME_LEN size
perf hists browser: Refuse 'a' hotkey on non symbolic views
perf ui browser: Use libslang to read keys
perf tools: Fix tracing info recording
perf hists browser: Elide DSO column when it is set to just one DSO, ditto for threads
perf hists: Don't consider filtered entries when calculating column widths
perf hists: Don't decay total_period for filtered entries
perf hists browser: Honour symbol_conf.show_{nr_samples,total_period}
perf hists browser: Do not exit on tab key with single event
perf annotate browser: Don't change selection line when returning from callq
perf tools: handle endianness of feature bitmap
perf tools: Add prelink suggestion to dso update message
perf script: Fix unknown feature comment
perf hists browser: Apply the dso and thread filters when merging new batches
perf hists: Move the dso and thread filters from hist_browser
perf ui browser: Honour the xterm colors
perf top tui: Give color hints just on the percentage, like on --stdio
perf ui browser: Make the colors configurable and change the defaults
perf tui: Remove unneeded call to newtCls on startup
perf hists: Don't format the percentage on hist_entry__snprintf
...
Fix up conflicts in arch/x86/kernel/kprobes.c manually.
Ingo's tree did the insane "add volatile to const array", which just
doesn't make sense ("volatile const"?). But we could remove the const
*and* make the array volatile to make doubly sure that gcc doesn't
optimize it away..
Also fix up kernel/trace/ring_buffer.c non-data-conflicts manually: the
reader_lock has been turned into a raw lock by the core locking merge,
and there was a new user of it introduced in this perf core merge. Make
sure that new use also uses the raw accessor functions.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1745 commits)
dp83640: free packet queues on remove
dp83640: use proper function to free transmit time stamping packets
ipv6: Do not use routes from locally generated RAs
|PATCH net-next] tg3: add tx_dropped counter
be2net: don't create multiple RX/TX rings in multi channel mode
be2net: don't create multiple TXQs in BE2
be2net: refactor VF setup/teardown code into be_vf_setup/clear()
be2net: add vlan/rx-mode/flow-control config to be_setup()
net_sched: cls_flow: use skb_header_pointer()
ipv4: avoid useless call of the function check_peer_pmtu
TCP: remove TCP_DEBUG
net: Fix driver name for mdio-gpio.c
ipv4: tcp: fix TOS value in ACK messages sent from TIME_WAIT
rtnetlink: Add missing manual netlink notification in dev_change_net_namespaces
ipv4: fix ipsec forward performance regression
jme: fix irq storm after suspend/resume
route: fix ICMP redirect validation
net: hold sock reference while processing tx timestamps
tcp: md5: add more const attributes
Add ethtool -g support to virtio_net
...
Fix up conflicts in:
- drivers/net/Kconfig:
The split-up generated a trivial conflict with removal of a
stale reference to Documentation/networking/net-modules.txt.
Remove it from the new location instead.
- fs/sysfs/dir.c:
Fairly nasty conflicts with the sysfs rb-tree usage, conflicting
with Eric Biederman's changes for tagged directories.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (59 commits)
MAINTAINERS: linux-m32r is moderated for non-subscribers
linux@lists.openrisc.net is moderated for non-subscribers
Drop default from "DM365 codec select" choice
parisc: Kconfig: cleanup Kernel page size default
Kconfig: remove redundant CONFIG_ prefix on two symbols
cris: remove arch/cris/arch-v32/lib/nand_init.S
microblaze: add missing CONFIG_ prefixes
h8300: drop puzzling Kconfig dependencies
MAINTAINERS: microblaze-uclinux@itee.uq.edu.au is moderated for non-subscribers
tty: drop superfluous dependency in Kconfig
ARM: mxc: fix Kconfig typo 'i.MX51'
Fix file references in Kconfig files
aic7xxx: fix Kconfig references to READMEs
Fix file references in drivers/ide/
thinkpad_acpi: Fix printk typo 'bluestooth'
bcmring: drop commented out line in Kconfig
btmrvl_sdio: fix typo 'btmrvl_sdio_sd6888'
doc: raw1394: Trivial typo fix
CIFS: Don't free volume_info->UNC until we are entirely done with it.
treewide: Correct spelling of successfully in comments
...
nmi.c needs an #include <linux/mca.h>:
arch/x86/kernel/nmi.c: In function ‘unknown_nmi_error’:
arch/x86/kernel/nmi.c:286:6: error: ‘MCA_bus’ undeclared (first use in this function)
arch/x86/kernel/nmi.c:286:6: note: each undeclared identifier is reported only once for each function it appears in
Another one is the hpwdt driver:
drivers/watchdog/hpwdt.c:507:9: error: ‘NMI_DONE’ undeclared (first use in this function)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Just convert all the files that have an nmi handler to the new routines.
Most of it is straight forward conversion. A couple of places needed some
tweaking like kgdb which separates the debug notifier from the nmi handler
and mce removes a call to notify_die.
[Thanks to Ying for finding out the history behind that mce call
https://lkml.org/lkml/2010/5/27/114
And Boris responding that he would like to remove that call because of it
https://lkml.org/lkml/2011/9/21/163]
The things that get converted are the registeration/unregistration routines
and the nmi handler itself has its args changed along with code removal
to check which list it is on (most are on one NMI list except for kgdb
which has both an NMI routine and an NMI Unknown routine).
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Corey Minyard <minyard@acm.org>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: Jack Steiner <steiner@sgi.com>
Link: http://lkml.kernel.org/r/1317409584-23662-4-git-send-email-dzickus@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There are numerous broken references to Documentation files (in other
Documentation files, in comments, etc.). These broken references are
caused by typo's in the references, and by renames or removals of the
Documentation files. Some broken references are simply odd.
Fix these broken references, sometimes by dropping the irrelevant text
they were part of.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The enable function was using the global timeout variable for local operations.
This resulted in the value of the global variable being corrupted, thus
breaking the code.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-mips@linux-mips.org
On platforms with no iCRU support don't print two, (possibly conflicting),
"NMI occurred" messages when the firmware is unable to source the NMI.
Please note that one of the enhancements to the v1.3.0 hpwdt driver is to panic and allow
KDUMP to succeed even on NMIs that are unknown to the platform firmware.
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Reviewed-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use the passed watchdog_device instead of the static global variable when
testing and setting the status in watchdog_ping, watchdog_start, and
watchdog_stop. Note that the callers of these functions are actually
passing the static global variable.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch add support for the bcma bus. Broadcom uses only Mips 74K
CPUs on the new SoC and on the old ons using ssb bus there are no Mips
74K CPUs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prepare bcm47xx to support different System buses. Before adding
support for bcma it should be possible to build bcm47xx without the
need of ssb. With this patch bcm47xx does not directly contain a
ssb_bus, but a union contain all the supported system buses. As a SoC
just uses one system bus a union is a good choice.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The newly added WATCHDOG_CORE option is a bool, but the help text suggests
it can be built as a module. Fix it up.
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
At present the module does not unset the NO_REBOOT bit upon shutdown, this
causes the BIOS to fail the POST once and reset. During the next boot it
displays the following error message:
***** Warning: System BOOT Fail *****
Your system last boot fail or POST interrupted.
Please enter setup to load default and reboot again.
Press F1 to continue, DEL to enter SETUP
With this patch the NO_REBOOT flag will be unset on shutdown and thus stop
this failure from occurring.
Tested on 'ASUS P5N32-E SLI with BIOS revision 1801' and
'ASUS P5N32-E SLI PLUS with BIOS revision 1502'.
Signed-off-by: Mart Gerrits <mart1987@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Fix the usage of mod_timer() and make the driver usable. mod_timer() must
be called with an absolute timeout in jiffies. The old implementation
used a relative timeout thus the hardware watchdog was never triggered.
Signed-off-by: David Engraf <david.engraf@sysgo.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Wim Van sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: stable <stable@kernel.org>
Add min_timeout (minimum timeout) and max_timeout
values so that the framework can check if the new
timeout value is between the minimum and maximum
timeout values. If both values are 0, then the
framework will leave the check for the watchdog
device driver itself.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Add support for extra ioctl calls by adding a
ioctl watchdog operation. This operation will be
called before we do our own handling of ioctl
commands. This way we can override the internal
ioctl command handling and we can also add
extra ioctl commands. The ioctl watchdog operation
should return the appropriate error codes or
-ENOIOCTLCMD if the ioctl command should be handled
through the internal ioctl handling of the framework.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Add support for the nowayout feature to the
WatchDog Timer Driver Core framework.
This feature prevents the watchdog timer from being
stopped.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Add support for the Magic Close feature to the
WatchDog Timer Driver Core framework.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
This part add's the WDIOC_SETTIMEOUT and WDIOC_GETTIMEOUT ioctl
functionality to the WatchDog Timer Driver Core framework.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
This part add's the WDIOC_SETOPTIONS ioctl functionality
to the WatchDog Timer Driver Core framework.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
This part add's the WDIOC_KEEPALIVE ioctl functionality to the
WatchDog Timer Driver Core framework. Please note that the
WDIOF_KEEPALIVEPING bit has to be set in the watchdog_info
options field.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
This part add's the basic ioctl functionality to the
WatchDog Timer Driver Core framework. The supported
ioctl call's are:
WDIOC_GETSUPPORT
WDIOC_GETSTATUS
WDIOC_GETBOOTSTATUS
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
The WatchDog Timer Driver Core is a framework
that contains the common code for all watchdog-driver's.
It also introduces a watchdog device structure and the
operations that go with it.
This is the introduction of this framework. This part
supports the minimal watchdog userspace API (or with
other words: the functionality to use /dev/watchdog's
open, release and write functionality as defined in
the simplest watchdog API). Extra functionality will
follow in the next set of patches.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
This patch is required to enable hpwdt to work on next generation HP servers
with iLO.
Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
remove unneeded pci.h include.
and include ioport.h to avoid build errors for the region functions.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
