The spu_runcntl_RW register is restored within spu_restore function.
So, at the end of spu_bind_context, the SPU context is not just loaded,
but running.
This change corrects the state switch to account the time as USER.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
There is a potential race between flushes of the entire SLB in the MFC
and the point where new entries are being established. The problem is
that we might put a ESID entry into the MFC SLB when the VSID entry has
just been cleared by the global flush.
This can be circumvented by holding the register_lock throughout both
the flushing and the creation of SLB entries.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
When we replace an SLB entry in the MFC after using up all the available
entries, there is a short window in which an incorrect entry is marked
as valid.
The problem is that the 'valid' bit is stored in the ESID, which is
always written after the VSID. Overwriting the VSID first will make the
original ESID entry point to the new VSID, which means that any
concurrent DMA accessing the old ESID ends up being redirected to the
new virtual address. A few cycles later, we write the new ESID and
everything is fine again.
That race can be closed by writing a zero entry to the ESID first, which
makes sure that the VSID is not accessed until we write the new ESID.
Note that we don't actually need to invalidate the SLB entry using the
invalidation register, which would also flush any ERAT entries for that
segment, because the segment translation does not become invalid but is
only removed from the SLB cache.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
There is a small race between the context save procedure
and the SPU interrupt handling, where we expect all interrupt
processing to have finished after disabling them, while
an interrupt is still being processed on another CPU.
The obvious fix is to call synchronize_irq() after disabling
the interrupts at the start of the context save procedure
to make sure we never access the SPU any more during an
ongoing save or even after that.
Thanks to Benjamin Herrenschmidt for pointing this out.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Currently, we get the following output from sputrace:
[5.097935954] 1606: spufs_ps_nopfn__enter (thread = 1605, spu = -1)
[5.097958164] 1606: spufs_ps_nopfn__insert (thread = 1605, spu = 15)
[5.097973529] 1607: spufs_ps_nopfn__enter (thread = 1605, spu = -1)
[5.097989174] 1607: spufs_ps_nopfn__insert (thread = 1605, spu = 14)
Which leads me to believe that 160[67] is the current thread ID, and
1605 is the context backing the psmap.
However, the 'current' and 'owner' tids are reversed - the 'current'
tid is on the right. This change puts the current thread ID in the
left-hand column instead, and renames the right to 'ctxthread'.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
At present, we have a situation where a context with no owner is
re-scheduled by spu_forget:
Thread 1: reading regs file Thread 2: context owner
spu_forget()
- ctx->owner = NULL
- set SPU_SCHED_WAS_ACTIVE
spu_acquire_saved()
- context is in saved state
spu_release_saved()
- SPU_SCHED_WAS_ACTIVE is set,
so spu_activate() the context,
which now has no owner
In spu_forget(), we shouldn't be requesting a re-schedule by setting
SPU_SCHED_WAS_ACTIVE. This change removes the set_bit in spu_forget(),
so that spu_release_saved() doesn't reinsert this destroyed context on
to the run queue.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
We have a small window where a spu context may be destroyed while
we're servicing a page fault (from another thread) to the context's
problem state mapping.
After we up_read() the mmap_sem, it's possible that the context is
destroyed by its owning thread, and so the later references to ctx
are invalid. This can maifest as a deadlock on the (now free()-ed)
context state mutex.
This change adds a reference to the context before we release the
mmap_sem, so that the context cannot be destroyed.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
m8xx_setup.c says:
/* Force all 8xx processors to use divide by 16 processor clock. */
And at the same time it is using bus-frequency for calculating
timebase. It is okay for most setups because bus-frequency is
equal to clock-frequency.
The problem emerges when cpu frequency is > 66MHz, quoting
u-boot/cpu/mpc8xx/speed.c:
if (gd->cpu_clk <= 66000000) {
sccr_reg |= SCCR_EBDF00; /* bus division factor = 1 */
gd->bus_clk = gd->cpu_clk;
} else {
sccr_reg |= SCCR_EBDF01; /* bus division factor = 2 */
gd->bus_clk = gd->cpu_clk / 2;
}
So in case of cpu clock > 66MHz, bus_clk = cpu_clk / 2. An then, from
Linux, we calculate timebase frequency as tb_freq = bus_clk / 16,
that is cpu_clk / 2 / 16, which is wrong.
This fixes the system time drifting problem on the EP885C board
running at 133MHz.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
For memory remove, we need to clean up htab mappings for the
section of the memory we are removing.
This implements support for removing htab bolted mappings for pSeries
logical partitions. Other sub-archs may need to implement similar
functionality for hotplug memory remove to work on them.
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
mpc52xx_set_psc_clkdiv is needed by PSC device drivers.
Signed-off-by: Eric Dujardin <eric.dujardin@sagem.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Setup i2c_board_info based on device tree contents. This has to be
a device_initcall since we need PCI to be probed by the time we
run it, but before the actual driver is initialized.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
At present, the __spufs_trap_data_map and __spu_trap_data_seq functions
exit if spu->flags has the SPU_CONTEXT_SWITCH_ACTIVE set. This was
resulting in suprious returns from these functions, as they may be
legitimately called when we have this bit set.
We only use it in these two sanity checks, so this change removes the
flag completely. This fixes hangs in the page-fault path of SPE apps.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Introduced by commit 79393fc46e
("kobject: convert pseries/power.c to kobj_attr interface").
sys_create_file takes a "struct attrbute *" not a "struct
kobj_addribute *".
arch/powerpc/platforms/pseries/power.c: In function 'apo_pm_init':
arch/powerpc/platforms/pseries/power.c:78: warning: passing argument 2 of 'sysfs_create_file' from incompatible pointer type
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2.6.25 has a regression where we can starve the scheduler by creating
(N_SPES+1) contexts, then running them one at a time.
The final context will never be run, as the other contexts are loaded on
the SPEs, none of which are repoted as free (ie, spu->alloc_state !=
SPU_FREE), so spu_get_idle() doesn't give us a spu to run on. Because
all of the contexts are stopped, none are descheduled by the scheduler
tick, as spusched_tick returns if spu_stopped(ctx).
This change replaces the spu_stopped() check with checking for SCHED_IDLE
in ctx->policy. We set a context's policy to SCHED_IDLE when we're not
in spu_run(). We also favour SCHED_IDLE contexts when looking for contexts
to unbind, but leave their timeslice intact for later resumption.
This patch fixes the following test in the spufs-testsuite:
tests/20-scheduler/02-yield-starvation
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Remove unused CONFIG_WANT_DEVICE_TREE
[POWERPC] Cell RAS: Remove DEBUG, and add license and copyright
[POWERPC] hvc_rtas_init() must be __init
[POWERPC] free_property() must not be __init
[POWERPC] vdso_do_func_patch{32,64}() must be __init
[POWERPC] Remove generated files on make clean
[POWERPC] Fix arch/ppc compilation - add typedef for pgtable_t
[POWERPC] Wire up new timerfd syscalls
[POWERPC] PS3: Update sys-manager button events
[POWERPC] PS3: Sys-manager code cleanup
[POWERPC] PS3: Use system reboot on restart
[POWERPC] PS3: Fix bootwrapper hang bug
[POWERPC] PS3: Fix reading pm interval in logical performance monitor
[POWERPC] PS3: Fix setting bookmark in logical performance monitor
[POWERPC] Fix DEBUG_PREEMPT warning when warning
* Add path_put() functions for releasing a reference to the dentry and
vfsmount of a struct path in the right order
* Switch from path_release(nd) to path_put(&nd->path)
* Rename dput_path() to path_put_conditional()
[akpm@linux-foundation.org: fix cifs]
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Cc: <linux-fsdevel@vger.kernel.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Steven French <sfrench@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the central patch of a cleanup series. In most cases there is no good
reason why someone would want to use a dentry for itself. This series reflects
that fact and embeds a struct path into nameidata.
Together with the other patches of this series
- it enforced the correct order of getting/releasing the reference count on
<dentry,vfsmount> pairs
- it prepares the VFS for stacking support since it is essential to have a
struct path in every place where the stack can be traversed
- it reduces the overall code size:
without patch series:
text data bss dec hex filename
5321639 858418 715768 6895825 6938d1 vmlinux
with patch series:
text data bss dec hex filename
5320026 858418 715768 6894212 693284 vmlinux
This patch:
Switch from nd->{dentry,mnt} to nd->path.{dentry,mnt} everywhere.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix cifs]
[akpm@linux-foundation.org: fix smack]
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CONFIG_DEVICE_TREE was the only user of CONFIG_WANT_DEVICE_TREE but
it was removed in commit id 2543133381
(bootwrapper: Build multiple cuImages).
This removes CONFIG_WANT_DEVICE_TREE from Kconfig and the defconfigs.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/powerpc/platforms/cell/ras.c still has DEBUG #defined, which is no
longer necessary. Disable it - this disables two pr_debugs().
While we're there this file should have a copyright notice and license,
so add both.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes the following section mismatch:
<-- snip -->
...
WARNING: vmlinux.o(.text+0x55648): Section mismatch in reference from the function .free_node() to the function .init.text:.free_property()
...
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
RCU style multiple probes support for the Linux Kernel Markers. Common case
(one probe) is still fast and does not require dynamic allocation or a
supplementary pointer dereference on the fast path.
- Move preempt disable from the marker site to the callback.
Since we now have an internal callback, move the preempt disable/enable to the
callback instead of the marker site.
Since the callback change is done asynchronously (passing from a handler that
supports arguments to a handler that does not setup the arguments is no
arguments are passed), we can safely update it even if it is outside the
preempt disable section.
- Move probe arm to probe connection. Now, a connected probe is automatically
armed.
Remove MARK_MAX_FORMAT_LEN, unused.
This patch modifies the Linux Kernel Markers API : it removes the probe
"arm/disarm" and changes the probe function prototype : it now expects a
va_list * instead of a "...".
If we want to have more than one probe connected to a marker at a given
time (LTTng, or blktrace, ssytemtap) then we need this patch. Without it,
connecting a second probe handler to a marker will fail.
It allow us, for instance, to do interesting combinations :
Do standard tracing with LTTng and, eventually, to compute statistics
with SystemTAP, or to have a special trigger on an event that would call
a systemtap script which would stop flight recorder tracing.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Mike Mason <mmlnx@us.ibm.com>
Cc: Dipankar Sarma <dipankar@in.ibm.com>
Cc: David Smith <dsmith@redhat.com>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Cc: "Frank Ch. Eigler" <fche@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-2.6.25' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Add arch-specific walk_memory_remove() for 64-bit powerpc
[POWERPC] Enable hotplug memory remove for 64-bit powerpc
[POWERPC] Add remove_memory() for 64-bit powerpc
[POWERPC] Make cell IOMMU fixed mapping printk more useful
[POWERPC] Fix potential cell IOMMU bug when switching back to default DMA ops
[POWERPC] Don't enable cell IOMMU fixed mapping if there are no dma-ranges
[POWERPC] Fix cell IOMMU null pointer explosion on old firmwares
[POWERPC] spufs: Fix timing dependent false return from spufs_run_spu
[POWERPC] spufs: No need to have a runnable SPU for libassist update
[POWERPC] spufs: Update SPU_Status[CISHP] in backing runcntl write
[POWERPC] spufs: Fix state_mutex leaks
[POWERPC] Disable G5 NAP mode during SMU commands on U3
Add a .show_options super operation to spufs.
Use generic_show_options() and save the complete option string in
spufs_fill_super().
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
simple_attr_close implementes ->release so it should be named accordingly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: <stefano.brivio@polimi.it>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg KH <greg@kroah.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sometimes simple attributes might need to return an error, e.g. for
acquiring a mutex interruptibly. In fact we have that situation in
spufs already which is the original user of the simple attributes. This
patch merged the temporarily forked attributes in spufs back into the
main ones and allows to return errors.
[akpm@linux-foundation.org: build fix]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: <stefano.brivio@polimi.it>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg KH <greg@kroah.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently the cell IOMMU fixed mapping just printks that it's been setup,
which is not particularly useful. Much more interesting is the address
ranges for the different windows. This adds one line to dmesg on a blade.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If we get a 64-bit dma mask we switch to the fixed ops and call
cell_dma_dev_setup(). If the driver then switches back to a 32-bit dma
mask for any reason we don't call cell_dma_dev_setup() again, which
has the potential to leave bogus data in dev->archdata.dma_data.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In order for the cell IOMMU fixed mapping to work we need "dma-ranges"
properties in the device tree. If there are none then there's no point
enabling the fixed mapping support.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The cell IOMMU fixed mapping support has a null pointer bug if you run
it on older firmwares that don't contain the "dma-ranges" properties.
Fix it and convert to using of_get_next_parent() while we're there.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Stop bits are only valid when the running bit is not set. Status bits
carry over from one invocation of spufs_run_spu() to another, so the
RUNNING bit gets added to the previous state of the register which may
have been a remote library call. In this case, it looks like another
library routine should be invoked, but the spe is actually running.
This fixes a problem with a testcase that exercises the scheduler.
Signed-off-by: Luke Browning <lukebrowning@us.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We don't need to update the libassist statistic with the context in a
runnable state, so do it after spu_disable_spu().
Signed-off-by: Luke Browning <lukebrowning@us.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, the kernel may fail to restart a SPE context which
has stopped and been swapped out.
This changes spu_backing_runcntl_write to emulate the real
SPU_Status register exactly. When the SPU Run Control register
is written with SPU_RunCntl[Run] set to '1', the physical SPU
automatically sets SPU_Status[R] and clears SPU_Status[CISHP].
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix various state_mutex leaks. The worst one was introduced by the
interrutible state_mutex conversion but there've been a few before
too. Notably spufs_wait now returns without the state_mutex held
when returning an error, which actually cleans up some code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luke Browning <lukebrowning@us.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It appears that with the U3 northbridge, if the processor is in NAP
mode the whole time while waiting for an SMU command to complete,
then the SMU will fail. It could be related to the weird backward
mechanism the SMU uses to get to system memory via i2c to the
northbridge that doesn't operate properly when the said bridge is
in napping along with the CPU. That is on U3 at least, U4 doesn't
seem to be affected.
This didn't show before NO_HZ as the timer wakeup was enough to make
it work it seems, but that is no longer the case.
This fixes it by disabling NAP mode on those machines while
an SMU command is in flight.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
While merging, I found a small bug that I forgot to send. I add an
offset to a value twice.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The addition of of_rtc for the Walnut board was only half complete. Select
OF_RTC in the Kconfig and include the appropriate header to make it compile.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The xics code does update the default server information when the boot
cpu is removed. This patch recognizes when the boot cpu is being
removed and updates the appropriate information based on the new 'boot
cpu'.
Failure to update this information can causes us to leave irqs pinned
to cpus that are being removed, especially when removing the boot cpu.
The cpu is removed from the kernel, but cpu dlpar remove operations
fail since we cannot return the cpu to the hypervisor.
Signed-off-by: Nathan Fonteno <nfont@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It appears that xics.c has its own of_get_cpu_node(). Remove this and
use the common one from prom.c.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This splits off the kexec path bits of the xics_teardown_cpu() routine
into its own xics_kexec_teardown_cpu() routine. With the previous
combined routine the CPPR for a cpu that is being removed may have its
CPPR reset in the plpar_eoi() call (which explicitly sets the CPPR to
a non-zero value). Splitting of the kexec bits of the code prevents
this from happening in the cpu remove path.
Once again, this does not cause the cpu remove from the kernel to
fail, but it does cause cpu dlpar operations to not be able to return
the cpu to the hypervisor.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The affinity mask in the virq descriptor needs to be set before we
reset the affinity for the virq. Without doing this the call to get
the new irq server fails and we end up leaving the virq pinned to the
cpu we are removing.
This does not fail the cpu remove from the kernel, but it does prevent
cpu dlpar remove operations from returning the cpu to the hypervisor.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
512x is very similar to 83xx and most
of this is patterned after code from 83xx.
New platform:
changed:
arch/powerpc/Kconfig
arch/powerpc/platforms/Kconfig
arch/powerpc/platforms/Kconfig.cputype
arch/powerpc/platforms/Makefile
new:
arch/powerpc/platforms/512x/*
include/asm-powerpc/mpc512x.h
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
calibrate_delay() must be __cpuinit, not __{dev,}init.
I've verified that this is correct for all users.
While doing the latter, I also did the following cleanups:
- remove pointless additional prototypes in C files
- ensure all users #include <linux/delay.h>
This fixes the following section mismatches with CONFIG_HOTPLUG=n,
CONFIG_HOTPLUG_CPU=y:
WARNING: vmlinux.o(.text+0x1128d): Section mismatch: reference to .init.text.1:calibrate_delay (between 'check_cx686_slop' and 'set_cx86_reorder')
WARNING: vmlinux.o(.text+0x25102): Section mismatch: reference to .init.text.1:calibrate_delay (between 'smp_callin' and 'cpu_coregroup_map')
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Christian Zankel <chris@zankel.net>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mainly, this involves two changes:
1) xilinx->xlnx (recognized standard is to use the stock ticker)
2) In order to have the device tree focus on describing what the
hardware is as exactly as possible, the compatible strings contain the
full IP name and IP version.
Signed-off-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Of_get_parent and of_find_compatible_node do a of_node_get, and thus a
corresponding of_code_put is needed in both the error case and the normal
return case.
The problem was found using the following semantic match.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T,T1,T2;
identifier E;
statement S;
expression x1,x2,x3;
int ret;
@@
T E;
...
* E = \(of_get_parent\|of_find_compatible_node\)(...);
if (E == NULL) S
... when != of_node_put(...,(T1)E,...)
when != if (E != NULL) { ... of_node_put(...,(T1)E,...); ...}
when != x1 = (T1)E
when != E = x3;
when any
if (...) {
... when != of_node_put(...,(T2)E,...)
when != if (E != NULL) { ... of_node_put(...,(T2)E,...); ...}
when != x2 = (T2)E
(
* return;
|
* return ret;
)
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Of_get_parent and of_find_compatible_node do an of_node_get, and thus a
corresponding of_code_put is needed in the error case.
The problem was found using the following semantic match.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T,T1,T2;
identifier E;
statement S;
expression x1,x2,x3;
int ret;
@@
T E;
...
* E = \(of_get_parent\|of_find_compatible_node\)(...);
if (E == NULL) S
... when != of_node_put(...,(T1)E,...)
when != if (E != NULL) { ... of_node_put(...,(T1)E,...); ...}
when != x1 = (T1)E
when != E = x3;
when any
if (...) {
... when != of_node_put(...,(T2)E,...)
when != if (E != NULL) { ... of_node_put(...,(T2)E,...); ...}
when != x2 = (T2)E
(
* return;
|
* return ret;
)
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/powerpc/platforms/83xx/mpc832x_rdb.c: In function ‘mpc832x_rdb_setup_arch’:
arch/powerpc/platforms/83xx/mpc832x_rdb.c:104: warning: ‘np’ is used uninitialized in this function
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The e300 c3 and c4 variants support hardware performance monitor counters
which are identical to those found in the e500.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some of the more recent e300 cores have the same performance monitor
implementation as the e500. e300 isn't book-e, so the name isn't
really appropriate. In preparation for e300 support, rename a bunch
of fsl_booke things to say fsl_emb (Freescale Embedded Performance Monitors).
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cleaned up IRQ layout and removed unsused ISU allocations.
Fixed RTC address typo from /dts-v1/ conversion.
Incorporated list suggestions to use an "iomega," vendor prefix,
and to use a node reference rather than a hard path.
Signed-off-by: Jon Loeliger <jdl@@jdl.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
I got this warning from gcc:
arch/powerpc/platforms/cell/axon_msi.c:118: warning: 'tmp' may be used uninitialized in this function
Which turns out to be a false positive, but pointed out that it was
possible for the error path in find_msi_translator() to do an extra
of_node_put on a node. This fixes it by localising the ref counting
a bit. As a side effect, the warning goes away.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There's a brown-paper-bag bug in axon_msi, we pass the address of our
FIFO directly to the hardware, without DMA mapping it. This leads to
DMA exceptions if you enable MSI & the IOMMU.
The fix is to correctly DMA map the fifo, dma_alloc_coherent() does
what we want - and we need to track the virt & phys addresses.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that we create of_platform devices earlier on cell, we can make the
axon_msi driver an of_platform driver. This makes the code cleaner in
several ways, and most importantly means we have a struct device.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently cell publishes OF devices at device_initcall() time, which
means the earliest a driver can bind to a device is also device_initcall()
time. We have a driver we want to register before other devices, so
publish the devices at subsys_initcall() time.
This should not cause any behaviour change for existing drivers, as they
are still bound at device_initcall() time.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
asm/commproc.h was renamed to asm/cpm1.h
sysdev/commproc.h was renamed to platforms/8xx/mpc8xx.h
m8xx_pic_init was renamed to mpc8xx_pics_init
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Reference count for the "neighbor" spu context was not
being correctly decremented after usage.
So, contexts used as reference during SPU affinity setup
were not being deallocated, leading to a memory leak.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently we only catch debug events through the 0x3fff status;
spufs_run_spu doesn't handle single-step SPE events.
This change adds a handler for conditions where the SPE is stopped due
to single-step-mode.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds markers two important points in the spufs code and a new
module (sputrace.ko) that allows reading these out through a proc file.
Long-term I'd rather see something like lttng extended to use the spufs
instrumentation, but for now I think this is a good enough quick
solution. We'll probably want to add various addition event in addition
to that ones I have already.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
SCCR USB bits are in a different location on the mpc8315.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch converts PPC's IOMMU to use the IOMMU helper functions. The IOMMU
doesn't allocate a memory area spanning LLD's segment boundary anymore.
iseries_hv_alloc and iseries_hv_map don't have proper device
struct. 4GB boundary is used for them.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On ACPI systems the target state set by acpi_pm_set_target() is
reset by acpi_pm_finish(), but that need not be called if the
suspend fails. All platforms that use the .set_target() global
suspend callback are affected by analogous issues.
For this reason, we need an additional global suspend callback that
will reset the target state regardless of whether or not the suspend
is successful. Also, it is reasonable to rename the .set_target()
callback, since it will be used for a different purpose on ACPI
systems (due to ACPI 1.0x code ordering requirements).
Introduce the global suspend callback .end() to be executed at the
end of the suspend sequence and rename the .set_target() global
suspend callback to .begin().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
[POWERPC] pasemi: Fix thinko in dma_direct_ops setup
The first patch will just fall through and still set dma_data to a bad
value, make it return directly instead.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
More late-caught fallout from the mainline merge. Commit
35e4a6e26d ("[POWERPC] Use
archdata.dma_data in dma_direct_ops and add the offset") claimed
"Now that all platforms using dma_direct_offset setup the
archdata.dma_data correctly, ..."
..but nope -- the pasemi iommu setup code that disables translation on
the DMA pci device didn't set dma_data correctly.
This fixes it.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support for setting up a fixed IOMMU mapping on certain
cell machines. For 64-bit devices this avoids the performance overhead of
mapping and unmapping pages at runtime. 32-bit devices are unable to use
the fixed mapping.
The fixed mapping is established at boot, and maps all of physical memory
1:1 into device space at some offset. On machines with < 30 GB of memory
we setup the fixed mapping immediately above the normal IOMMU window.
For example a machine with 4GB of memory would end up with the normal
IOMMU window from 0-2GB and the fixed mapping window from 2GB to 6GB. In
this case a 64-bit device wishing to DMA to 1GB would be told to DMA to
3GB, plus any offset required by firmware. The firmware offset is encoded
in the "dma-ranges" property.
On machines with 30GB or more of memory, we are unable to place the fixed
mapping above the normal IOMMU window as we would run out of address space.
Instead we move the normal IOMMU window to coincide with the hash page
table, this region does not need to be part of the fixed mapping as no
device should ever be DMA'ing to it. We then setup the fixed mapping
from 0 to 32GB.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Split out the ioid fetching and checking logic so we can use it elsewhere
in a subsequent patch.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add support to cell_iommu_setup_page_tables() for handling two windows,
the dynamic window and the fixed window. A fixed window size of 0
indicates that there is no fixed window at all.
Currently there are no callers who pass a non-zero fixed window, but the
upcoming fixed IOMMU mapping patch will change that.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Split the IOMMU logic out from cell_dma_dev_setup() into a separate
function. If we're not using dma_direct_ops or dma_iommu_ops we don't
know what the hell's going on, so BUG.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Split cell_iommu_setup_hardware() into two parts. Split the page table
setup into cell_iommu_setup_page_tables() and the bits that kick the
hardware into cell_iommu_enable_hardware().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Split out the logic that allocates a struct iommu into a separate
function. This can fail however the calling code has never cared - so
just return if we can't allocate an iommu.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Forgot to export this one. Needed when pasemi_mac is compiled as a module.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi: DMA engine management library
Introduce a DMA management library to manage the various DMA resources
on the PA Semi SoCs. Since several drivers need to allocate these shared
resources, provide some abstractions as well as allocation/free functions
for channels, etc.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* Allow multiple boards to be selected in a single build
* Removed Kconfig option '83xx' which existed only for compat with arch/ppc
* Removed Kconfig option 'PPC_MPC836x' since its not used
* Renamed Kconfig option 'MPC834x' to 'PPC_MPC834x' to match others
* Added a multiplatform 83xx defconfig (mpc83xx_defconfig).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Allow multiple boards to be selected in a single build
* Removed Kconfig option '85xx' which existed only for compat with arch/ppc
* Added a multiplatform 85xx defconfig (mpc85xx_defconfig). This builds
all 85xx boards except sbc8560 and stx_gp3 since these to boards have
board specific ifdef in driver code that may break all other boards
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
primarily based on mpc837x mds code.
Signed-off-by: Joe D'Abbraccio <ljd015@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
mpc8315 identical to mpc8313 here, just check compatible.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
prepare for adding support for the mpc8315 rdb, since they are
identical wrt platform code.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Now we're searching for "fsl,qe", "fsl,qe-muram", "fsl,qe-muram-data"
and "fsl,qe-ic".
Unfortunately it's still impossible to remove device_type = "qe"
from the existing device trees because older u-boots are looking for it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* "simple-bus" covers all our needs for of_platform_bus_probe()
* make device tree name just 'soc' not 'soc85..'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Rename commproc.[ch] to cpm1.[ch] to be more consistent with cpm2. Also
rename cpm2_common.c to cpm2.c as suggested by Scott Wood. Adjust the
includes accordingly.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Directly include mpc885ads.h from mpc885ads_setup.c. Now we can get rid
of the arch dependent includes in mpc8xx.h.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move cpm1 specific prototypes to asm/commproc.h and mpc8xx specific
prototypes to asm/mpc8xx.h. Adjust includes accordingly. Remove now
unneeded sysdev/commproc.h.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
m8xx_calibrate_decr seems to be a misspelled prototype for
mpc8xx_calibrate_decr. As it's not needed anyways, just remove it.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
m8xx_pic_init calls both mpc8xx_pic_init and cpm_pic_init. Renaming the
function to use the same name space as the rest of the mpc8xx
specific funtions and to be more meaningful.
m8xx_pic_init is declared in ppc8xx_pic.h but defined nowhere in the ppc
tree. Remove it.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This adds the basic support for the Wind River SBC834x boards. The
SBC8349 is more common, although it should work on the SBC8347 board
as well. Support is heavily based on the existing MPC834x_MDS code.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This adds the basic support for the Wind River SBC8548 board, implemented
as powerpc. It closely follows the implementation of the MPC8548CDS.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Currently there is no way to disable the CPM2 support. Some boards,
like the SBC8560 have their own external UART and don't have any direct
dependencies on the CPM for a serial console or anything else.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This adds support for the Wind River SBC8560 board, implemented as
powerpc. It closely follows the implementation of the MPC8560ADS.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
PSC drivers should not access the CDM registers directly. Instead provide
a common routine for setting the PSC clock parameters with the required
locking.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Update MPC5200 drivers to also look for compatible properties in the
form "fsl,mpc5200-*" to better conform to open firmware generic names
recommended practice as published here:
http://www.openfirmware.org/1275/practice/gnames/gnamv14a.html
This patch should *not* break compatibility with older device trees
which do not use the 'fsl,' prefix. The drivers will still bind against
the older names also.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Put all the mpc5200 board config option behind a menu item to get them
out of the top level of the platform support list
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Replace all lock_cpu_hotplug/unlock_cpu_hotplug from the kernel and use
get_online_cpus and put_online_cpus instead as it highlights the
refcount semantics in these operations.
The new API guarantees protection against the cpu-hotplug operation, but
it doesn't guarantee serialized access to any of the local data
structures. Hence the changes needs to be reviewed.
In case of pseries_add_processor/pseries_remove_processor, use
cpu_maps_update_begin()/cpu_maps_update_done() as we're modifying the
cpu_present_map there.
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add the base platform support for the PIKA Warp boards.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch extends the Ebony and Walnut platform code to instantiate
the existing ds1742 RTC class driver for the DS1743 RTC/NVRAM chip
found on both those boards. The patch uses a helper function to scan
the device tree and instantiate the appropriate platform_device based
on it, so it should be easy to extend for other boards which have mmio
mapped RTC chips.
Along with this, the device tree binding for the ds1743 chips is
tweaked, based on the existing DS1385 OF binding found at:
http://playground.sun.com/1275/proposals/Closed/Remanded/Accepted/346-it.txt
Although that document covers the NVRAM portion of the chip, whereas
here we're interested in the RTC portion, so it's not entirely clear
if that's a good model.
This implements only RTC class driver support - that is /dev/rtc0, not
/dev/rtc, and the low-level get/set time callbacks remain
unimplemented. That means in order to get at the clock you will
either need a modified version of hwclock which will look at
/dev/rtc0, or you'll need to configure udev to symlink rtc0 to rtc.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Commit 6d98bda79b changed the init order
for chrp_pci_fixup_vt8231_ata().
It can not work anymore because either the irq is not yet set to 14 or
pci_get_device() returns nothing. At least the printk() in
chrp_pci_fixup_vt8231_ata() does not trigger anymore.
pata_via works again on Pegasos with the change below.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently the IOMMU code allocates one page for the segment table, that
isn't safe if we have more than 132 GB of RAM.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rather than using the global variable, have celleb use its own
variable to store the direct DMA offset.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rather than using the global variable, have cell use its own variable
to store the direct DMA offset.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Celleb always uses dma_direct_ops, and sets dma_direct_offset, so it
too should set dma_data to dma_direct_offset.
Currently there's no pci_dma_dev_setup() routine for Celleb so add one.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Store the direct_dma_offset in each device's dma_data in the case
where we're using the direct DMA ops.
We need to make sure we setup the ppc_md.pci_dma_dev_setup() callback
if we're using a non-zero offset.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove the PS3 workaround needed to support sparsemem SPU mappings.
The SPU mappings no longer use sparsemem, so this workaround is no
longer needed.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add PS3 logical performance monitor (lpm) device driver.
The PS3's LV1 hypervisor provides a Logical Performance Monitor that
abstracts the Cell processor's performance monitor features for use
by guest operating systems.
Signed-off-by: Takashi Yamamoto <TakashiA.Yamamoto@jp.sony.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add PS3 logical performance monitor device support to the
PS3 system-bus and platform device registration routines.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cleanup coding errors in arch/powerpc/platforms/ps3/repository.c as
reported by sparse and checkpatch.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
PS3: Add repository polling loop to work around timing bug
On some firmware versions (e.g. 1.90), the storage device may not show up
in the repository immediately after receiving the notification message.
Add a small polling loop to make sure we don't miss it.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The PS3 hypervisor has a storage device notification mechanism to wait
until a storage device is ready. Unfortunately the storage device
probing code used this mechanism in an incorrect way, needing a
polling loop and handling of devices that are not yet ready.
This change corrects this by:
- First waiting for the reception of an asynchronous notification
that a new storage device became ready,
- Then looking up the storage device in the device repository.
On shutdown, the storage probe thread is stopped and the storage
notification device is closed using a reboot notifier.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The storage probe feature of the PS3 hypervisor returns device IDs. Add
the corresponding repository routine ps3_repository_find_device_by_id()
which can be used to retrieve the device info from the repository.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change the PS3 bus_id and dev_id from type unsigned int to u64. These
IDs are 64-bit in the repository, and the special storage notification
device has a device ID of ULONG_MAX.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
All kobjects require a dynamically allocated name now. We no longer
need to keep track if the name is statically assigned, we can just
unconditionally free() all kobject names on cleanup.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
/sys/power should not be a kset, that's overkill. This patch renames it
to power_kset and fixes up all usages of it in the tree.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This makes the code a bit simpler and and gets us one step closer to
deleting the deprecated subsys_attr code.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Manish Ahuja <mahuja@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Dynamically create the kset instead of declaring it statically. We also
rename power_subsys to power_kset to catch all users of the variable and
we properly export it so that people don't have to guess that it really
is present in the system.
The pseries code is wierd, why is it createing /sys/power if CONFIG_PM
is disabled? Oh well, stupid big boxes ignoring config options...
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't need a "default" ktype for a kset. We should set this
explicitly every time for each kset. This change is needed so that we
can make ksets dynamic, and cleans up one of the odd, undocumented
assumption that the kset/kobject/ktype model has.
This patch is based on a lot of help from Kay Sievers.
Nasty bug in the block code was found by Dave Young
<hidave.darkstar@gmail.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use cuImage bootwrapper until U-Boot port is completed.
Derived heavily from Linkstation port.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Andy Wilcox <andy@protium.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Prevents miscellaneous users from declaring it locally.
Signed-off-by: Jon Loeliger <jdl@freecale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Call of_platform_bus_probe() on the MPC8641 HPCN, similar to what is
done for other platforms.
Signed-off-by: Wade Farnsworth <wfarnsworth@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add NAND to device tree, and call of_platform_bus_probe().
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This board is also resold by Freescale under the names
"QUICCStart MPC8248 Evaluation System" and "CWH-PPC-8248N-VE".
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Update the MPC8610 HPCD files to support the audio driver. Update
booting-without-of.txt with information on the SSI device.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
IPIC is not just for 83xx anymore so make it a separate config option.
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add in missing of_node_put() after cpm2_pic_init(). This and other coding
style cleanups as suggested by Stephen Rothwell.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Define the layout of a binary blob that contains a QE firmware and instructions
on how to upload it. Add function qe_upload_firmware() to parse the blob
and perform the actual upload. Fully define 'struct rsp' in immap_qe.h to
include the actual RISC Special Registers. Added description of a new
QE firmware node to booting-without-of.txt.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds localbus and pata nodes to use CF IDE interface
on MPC8349E-mITX boards.
Patch also adds code to probe localbus.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove device_type = "usb" for 83xx SoC USB controller
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add chip specific and board specific initialization for MPC837x USB.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds support for 'mpc5200-simple-platform' compatible
boards which do not need a platform specific setup. Such boards
are supported assuming the following:
- GPIO pins are configured by the firmware,
- CDM configuration (clocking) is setup correctly by firmware,
- if the 'fsl,has-wdt' property is present in one of the
gpt nodes, then it is safe to use such gpt to reset the board,
- PCI is supported if enabled in the kernel configuration
and if there is a PCI bus node defined in the device tree.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
mpc5200 platform code defines a bunch of map functions which duplicate the
functionality of of_iomap(). Remove them and use of_iomap() instead.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch moves a generic pci init code from lite5200
platform file to a common mpc52xx_setup_pci() routine
and adds additional compatibility property verification.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Define MPC52xx specific device id list, add new
'fsl,lpb' compatible id for LocalPlus Bus.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
xlate_iomm_address() really wants the ds_addr to pass to the HV, so store
that value (instead of the BAR number) when we allocate the device bars.
This is not a fast path, so we can look up the device_node property
there instead of using the bussubno field of the pci_dn.
The other user of iseries_ds_addr() was already scanning the device tree,
so looking up a property will not slow it down any more.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Similar to of_find_compatible_node(), of_find_matching_node() and
for_each_matching_node() allow you to iterate over the device tree
looking for specific nodes, except that they take of_device_id
tables instead of strings.
This also moves of_match_node() from driver/of/device.c to
driver/of/base.c to colocate it with the of_find_matching_node which
depends on it.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move electra-ide glue over to the new pata_of_platform framework, and
add the quirks needed to that driver.
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit 473980a993 added a call to clear
the SLB shadow buffer before registering it. Unfortunately this means
that we clear out the entries that slb_initialize has previously set in
there. On POWER6, the hypervisor uses the SLB shadow buffer when doing
partition switches, and that means that after the next partition switch,
each non-boot CPU has no SLB entries to map the kernel text and data,
which causes it to crash.
This fixes it by reverting most of 473980a9 and instead clearing the
3rd entry explicitly in slb_initialize. This fixes the problem that
473980a9 was trying to solve, but without breaking POWER6.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Before we register the SLB shadow buffer, we need to invalidate the
entries in the buffer, otherwise we can end up stale entries from when
we previously offlined the CPU.
This does this invalidate as well as unregistering the buffer with
PHYP before we offline the cpu. Tested and fixes crashes seen on
970MP (thanks to tonyb) and POWER5.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Includes both flavors of plb, opb, dcr, and a pseudo 'compound' bus
for representing compound peripherals containing more than one logical
device.
Signed-off-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The logic that checks to see if a machine check is caused by an NMI will
always match when NMI hasn't been initialized, since the mpic routine
will return NO_IRQ (and that's what the nmi_virq value is as well).
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit aed3a8c9bb introduced a
definition of notify_spus_active in .../cell/spu_syscalls.c, and
another definition under #ifndef MODULE in .../cell/spufs/sched.c.
The latter is not necessary and causes the build to fail when
CONFIG_SPU_FS=y, so this removes it. It also removes the export
of do_notify_spus_active, which is unnecessary.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
By default the OpenPIC on PWRficient will bias to one core (since that
will improve changes of the other core being able to stay idle/powered
down). However, this conflicts with most irq load balancing schemes,
since setting an interrupt to be delivered to either core doesn't really
result in the load being shared. It also doesn't work well with the
soft irq disable feature of PPC, since EE will stay on until the first
interrupt is taken while soft disabled.
Set the gconf0 config bit that enables even distribution of interrupts
among the two cores.
Signed-off-by: Olof Johansson <olof@lixom.net>
Some PWRficient-based boards have a NMI button that's wired up to a GPIO
as interrupt source. By configuring the openpic accordingly, these get
delivered as a machine check with high priority, instead of as an external
interrupt.
The device tree contains a property "nmi-source" in the openpic node
for these systems, and it's the (hwirq) source for the input.
Also, for these interrupts, the IACK is read from another register than
the regular (MCACK instead), but they are EOI'd as usual. So implement
said function for the mpic driver.
Finally, move a couple of external function defines to include/ instead
of local under sysdev. Being able to mask/unmask and eoi directly saves
us from setting up a dummy irq handler that will never be called.
Signed-off-by: Olof Johansson <olof@lixom.net>
Fix a bug in the printing of the os-area magic numbers which assumed
that magic numbers were zero terminated strings. The magic numbers
are represented in memory as integers. If the os-area sections are
not initialized correctly they could contained random data that would
be printed to the display. Also unify the handling of header and db
magic numbers and make both of type array of u8.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This removes an OProfile dependency on the spufs module. This
dependency was causing a problem for multiplatform systems that are
built with support for Oprofile on Cell but try to load the oprofile
module on a non-Cell system.
Signed-off-by: Bob Nelson <rrnelson@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some machine_xx_initcall macros were recently added that check for the machine
type before calling the function. This converts the 4xx platforms to use those
for bus probing.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Remove the declarations for isa_io_base and isa_mem_base as they are declared
in pci-common.c now.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Enable PCI support for these eval boards among other things. Also selects
PCI for Rainier in the Kconfig file.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds basic support for the AMCC Makalu board to arch/powerpc.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
For EMAC support, 405EX needs to be defined to enable the corresponding
EMAC features (IBM_NEW_EMAC_EMAC4, etc.).
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
A small error caused a header file to be removed making sequoia support no
longer compile. Fix it.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This makes 4xx embedded platforms re-assign all PCI resources as we
pretty much never care about what the various firmwares have done on
these, it's generally not compatible with the way the kernel will map
the bridges.
We still need to also enable bus renumbering on some of them, but I
will do that from a separate patch after I've fixed 4xx PCIe to handle
all bus numbers.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds base support for the Katmai board, including PCI-X and
PCI-Express (but no RTC, nvram, etc... yet).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds the device-tree bits & call to ppc4xx_pci_find_bridges()
to make PCI work on the Bamboo board
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds base support for the AMCC Taishan 440GX evaluation
board.
Signed-off-by: Hugh Blemings <hugh@blemings.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This wires up the 4xx PCI support & device-tree bits for the
405GP based Walnut platform.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Brings EP405 support to arch/powerpc. The IRQ routing for the CPLD
comes from a device-tree property, PCI is working to the point where
I can see the video card, USB device, and south bridge.
This should work with both EP405 and EP405PC.
I've not totally figured out how IRQs are wired on this hardware
though, thus at this stage, expect only USB interrupts working,
pretty much the same as what arch/ppc did.
Also, the flash, nvram, rtc and temp control still have to be wired.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds some basic real mode based early udbg support for 40x
in order to debug things more easily
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This wires up the 4xx PCI support & device tree bits for
440GP based Ebony platform.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds a cputable function pointer for the CPU-side machine
check handling. The semantic is still the same as the old one,
the one in ppc_md. overrides the one in cputable, though
ultimately we'll want to change that so the CPU gets first.
This removes CONFIG_440A which was a problem for multiplatform
kernels and instead fixes up the IVOR at runtime from a setup_cpu
function. The "A" version of the machine check also tweaks the
regs->trap value to differenciate the 2 versions at the C level.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Maple and pasemi both require PCI as does CONFIG_OF_PLATFORM_PCI.
The default setting of CONFIG_ISA_DMA_API is set to match the protection
around the relevant routines in asm/dma.h.
I also had to remove the PMAC platform from the combined build. The
precis is that to build a 64 bit kernel with no PCI, you can only include
pSeries and iSeries.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Based on an original patch from Arnd Bergmann
<arnd.bergmann@de.ibm.com>
If there's no entry in the mailbox, then a read on the _info file will
return data from an uninitialised variable.
This change returns EOF if there's no mailbox info available instead.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes the behavior of spufs when a spu tries a DMA operation
based on a wrong / unavailable address.
Instead of just generating a SIGBUS signal, spufs now
generates a SIGSEGV signal and restarts the problematic DMA operation
after the execution of the application's signal handler. This allows
applications to employ user-level paging systems.
Although the restart_dma function is called before the application's
signal handler, the operation is not actually performed at this time,
since the spu context is already stopped. The operation only takes
place when spu_run is restarted (which happens automatically).
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The original spusched_timer was designed to take effect only when
a context is waiting in the runqueue.
This change adds an additional lower-freq timer has been added to
purely handle the spu_load updates. The new timer will be triggered
per LOAD_FREQ ticks.
Signed-off-by: Aegis Lin <aegislin@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
