This resolves the merge problems with:
drivers/usb/dwc3/gadget.c
drivers/usb/musb/tusb6010.c
that had been seen in linux-next.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of ep0 out, if length is not aligned to maxpacket size then we use
dwc->ep_bounce_addr for dma transfer and not request->dma. Since, we have
alreday done memcpy from dwc->ep0_bounce to request->buf, so we do not need to
issue cache sync function. In fact, cache sync function will bring wrong data
in request->buf from request->dma in this scenario.
So, cache sync function must not be executed in case of ep0 bounced.
Cc: <stable@vger.kernel.org> # v3.4 v3.5
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 68d3e66 (usb: dwc3: ep0: fix for possible early
delayed_status) added handling for early delayed status,
but the current code only works because so far delayed
status will always be on the IN direction.
This patch makes the code more robust by making sure that
we can handle all directions properly.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Due to the late Silicon limitation found, we are
now pre-starting DATA phase's TRBs. If, still, we
get XferNotReady(DATA) we will ignore it unless
we're getting it for the wrong direction.
In that case we must keep the error case handling
plus add a ENDTRANSFER command to forcefully end
the Data TRB we started previously, then continue
to SetStall and so on.
Signed-off-by: Felipe Balbi <balbi@ti.com>
We uncovered a limitation of this core WRT to the
Link Layer Compliance Suite's TD7.06.
On that test, host will start a GetDescriptor(DEVICE)
standard request, but it will do so only on the
SETUP phase, meaning there will *NOT* be any DATA or
STATUS phases.
The idea of the test is to verify robustness of the
IP WRT framing errors, so the test will send a
sequence of different SETUP_DPs each with a different
framing error and the Suite expects us to be able to
receive all SETUP_DPs with no timeouts.
This core, has the ability to tell us which phase the
host is expecting before we start it. Whenever we
receive a TP or DP when no transfers are cached on
the internal IP's caches, the IP will generate a
XferNotReady event with status informing us (in case
of physical ep0/ep1) if it's related to DATA or STATUS
phases - SETUP phase is expected to be prestarted.
Because we're always waiting for XferNotReady
events for DATA and STATUS phases, we will never
be able to know that the Host wants to start another
SETUP phase instead, which will render us "not
compliant" with TD7.06.
In order to "fix" the problem we must not rely
on XferNotReady events for the DATA phase and try
to always pre-start DATA transfers on physical
endpoints 0 and 1. If host goes back to SETUP phase
from DATA phase we will receive a XferComplete for
that phase with TRB's status set to SETUP_PENDING,
which is only useful for printing a debugging log as
the core expects us to still go through to the STATUS
phase, initiate a CONTROL_STATUS TRB just so it
completes right away and, only then, we go back to
the pending SETUP phase.
SNPS has decided to modify the programming model of
the core so that on-demand DATA phases will not be
supported anymore. Note that this limitation does not
affect 2-stage transfers, meaning that if TD7.06 would
start a 2-stage transfer instead of a 3-stage transfer,
we would receive a "fake" XferNotReady(STATUS) which
would complete right after being initiated with
SETUP_PENDING status.
Other endpoints are also not affected, so we can still
use on-demand transfers on Bulk/Isoc/Interrupt endpoints.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Databook doesn't say we should stall if we
get XferNotReady(STATUS) while we're expecting
something else.
Instead of stalling and restarting, tests have
proven that ignoring the event is far more
effective.
This problem has been caught while rewriting
ep0 handling in order we pass Link Layer TD7.6.
Signed-off-by: Felipe Balbi <balbi@ti.com>
We can return early from each if () branch
and split the special cases for clarity. While
at that also add a comment to the delayed_status
case.
Signed-off-by: Felipe Balbi <balbi@ti.com>
As per databook, ACCEPT{U1,U2}ENA bits should be set after receiving
SetConfiguration Command.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
set_halt for ep0 is called to stall a deferred control responses by the
gadget. We already have a function to stall default control endpoint.
This patch points set_halt for ep0 to the already available function.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Michel Sanches <michel.sanches@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In case we try to start an invalid test mode, we
will call dwc3_ep0_stall_and_restart() but we will
also call dwc3_ep0_out_start() which will start
a second transfer on ep0.
Let's prevent any problems by returning early in
the error case.
Signed-off-by: Felipe Balbi <balbi@ti.com>
That's a much more intuitive name as that function
is only called at the completion of a Status Phase.
It also matches dwc3_ep0_complete_data() for
the completion of Data Phase.
Signed-off-by: Felipe Balbi <balbi@ti.com>
USB is always little endian, but this driver
could run on non little endian cpus. Let's
be carefull with that.
Signed-off-by: Felipe Balbi <balbi@ti.com>
On our Transfer Not Ready handlers, only
dwc3_ep0_do_control_status() had a different
list of parameters.
Align on the parameters in order to keep consistency.
No functional changes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
IS_ALIGNED provides a much faster operation for
checking proper size alignment then a modulo
operation. Let's use it.
Reported-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When DWC3_EP_PENDING_REQUEST flag is set for a Control OUT Data
phase transfer, we would be missing the proper handling for
unaligned OUT requests, thus hanging a transfer.
Since proper handling is already done on dwc3_ep0_do_control_data(),
we simply re-factor that function so it can be re-used from
__dwc3_gadget_ep0_queue().
Reported-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
we're now have DWC3_EP0_BOUNCE_SIZE to tell
us the actual size of the bufer. Let's use that
instead of ep0 wMaxPacketSize.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This pull request contains one workaround for a Silicon
Issue found on all RTL releases prior to 2.20a, which
would cause a metastability state on Run/Stop bit.
We also have some patches implementing a few extra Standard
requests introduced by USB3 spec (Set SEL and Set Isoch Delay),
as well as one patch, which has been pending for a long time,
implementing LPM support.
Last, but not least, we are splitting the host address space
out of the dwc3 core driver otherwise xHCI won't be able to
request_mem_region() its own address space. This patch is
only needed because we are (as we should) re-using the xHCI
driver, which is a completely separate module.
Together with these three big changes, come a few extra preparatory
patches which most move code around, define macros and so on, as
well as a fix for Isochronous transfers which hasn't been triggered
before.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=qgf/
-----END PGP SIGNATURE-----
Merge tag 'dwc3-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
usb: dwc3: patches for v3.5 merge window
This pull request contains one workaround for a Silicon
Issue found on all RTL releases prior to 2.20a, which
would cause a metastability state on Run/Stop bit.
We also have some patches implementing a few extra Standard
requests introduced by USB3 spec (Set SEL and Set Isoch Delay),
as well as one patch, which has been pending for a long time,
implementing LPM support.
Last, but not least, we are splitting the host address space
out of the dwc3 core driver otherwise xHCI won't be able to
request_mem_region() its own address space. This patch is
only needed because we are (as we should) re-using the xHCI
driver, which is a completely separate module.
Together with these three big changes, come a few extra preparatory
patches which most move code around, define macros and so on, as
well as a fix for Isochronous transfers which hasn't been triggered
before.
[ resolved conflicts and build error in drivers/usb/dwc3/gadget.c - gregkh]
This is basically a noop for DWC3. We don't have
to do anything. Basically we test if the request
parameters are correct, cache the Isochronous
Delay and return success.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch implements Set SEL Standard Request
support for dwc3 driver. It needs to issue a command
to the controller passing the timing we received on
the data phase of the Set SEL request.
Signed-off-by: Felipe Balbi <balbi@ti.com>
On device loading the driver enables LPM and the acceptance of U1 and U2
states. The [Set|Clear]Feature requests for "U1/U2" are forwarded
directly to the hardware and allow / forbid the initiation of the low
power links.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Without this default case returning an error,
thus replying with a stall, we would fail
USB30CV TD 9.11 Bad Feature test case.
Cc: stable@vger.kernel.org
Signed-off-by: Gerard Cauvy <g-cauvy1@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
due to a HW limitation we have a bounce buffer for ep0
out transfers which are not aligned with MaxPacketSize.
On such case we were not increment r->actual as we should.
This patch fixes that mistake.
Cc: stable@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
To allow ep0 out transfers of upto bounce buffer size
instead of maxpacketsize, use the transfer size as multiple
of ep0 maxpacket size.
Cc: stable@vger.kernel.org
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Partha Basak <p-basak2@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Here are the changes for v3.4 merge window.
It includes a new glue layer for Samsung's Exynos platform, a simplification of
memory management on DWC3 driver by using dev_xxx functions, a few
optimizations to IRQ handling by dropping memcpy() and using bitshifts, a fix
for TI's OMAP5430 TX Fifo Allocation, two fixes on USB2 test mode
implementation (one on debugfs and one on ep0), and several minor changes such
as whitespace cleanups, simplification of a few parts of the code, decreasing a
long delay to something a bit saner, dropping a header which was included twice
and so on.
The highlight on this merge is the support for Samsung's Exynos platform,
increasing the number of different users for this driver to three.
Note that Samsung Exynos glue layer will only compile on platforms which
provide implementation for the clk API for now. Once Samsung supports
pm_runtime, that limitation can be dropped from the Makefile.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=4Z2+
-----END PGP SIGNATURE-----
Merge tag 'dwc3-for-v3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
usb: dwc3: changes for v3.4 merge window
Here are the changes for v3.4 merge window.
It includes a new glue layer for Samsung's Exynos platform, a simplification of
memory management on DWC3 driver by using dev_xxx functions, a few
optimizations to IRQ handling by dropping memcpy() and using bitshifts, a fix
for TI's OMAP5430 TX Fifo Allocation, two fixes on USB2 test mode
implementation (one on debugfs and one on ep0), and several minor changes such
as whitespace cleanups, simplification of a few parts of the code, decreasing a
long delay to something a bit saner, dropping a header which was included twice
and so on.
The highlight on this merge is the support for Samsung's Exynos platform,
increasing the number of different users for this driver to three.
Note that Samsung Exynos glue layer will only compile on platforms which
provide implementation for the clk API for now. Once Samsung supports
pm_runtime, that limitation can be dropped from the Makefile.
Conflicts:
drivers/usb/dwc3/gadget.c
Transfer resource index is cleared in hardware when XFERCOMPLETE
event is generated, so clear the driver's res_trans_idx variable
immediately after that event is received. The upcoming hibernation
patches depend on this change.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
For am5536udc we have just simple coding style fixes. Nothing that has any
potential to cause any issues going forward.
With mv_udc, there's only one single change removing an unneeded NULL check.
at91_udc also only saw a single change this merge window, and that's only
removing a duplicated header.
The Renesas controller has a few more involved changes. Support for SUDMAC was
added, there's now a special handling of IRQ resources for when the IRQ line is
shared between Renesas controller and SUDMAC, we also had a bug fix where
Renesas controller would sleep in atomic context while doing DMA transfers from
a tasklet. There were also a set of minor cleanups.
The FSL UDC also had a scheduling in atomic context bug fix, but that's all.
Thanks to Sebastian, the dummy_hcd now works better than ever with support for
scatterlists and streams. Sebastian also added SuperSpeed descriptors to the
serial gadgets.
The highlight on this merge is the addition of a generic API for mapping and
unmapping usb_requests. This will avoid code duplication on all UDC controllers
and also kills all the defines for DMA_ADDR_INVALID which UDC controllers
sprinkled around. A few of the UDC controllers were already converted to use
this new API.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=RR+f
-----END PGP SIGNATURE-----
Merge tag 'gadget-for-v3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
USB: Gadget: changes for 3.4
This merge is rather big. Here's what it contains:
For am5536udc we have just simple coding style fixes. Nothing that has any
potential to cause any issues going forward.
With mv_udc, there's only one single change removing an unneeded NULL check.
at91_udc also only saw a single change this merge window, and that's only
removing a duplicated header.
The Renesas controller has a few more involved changes. Support for SUDMAC was
added, there's now a special handling of IRQ resources for when the IRQ line is
shared between Renesas controller and SUDMAC, we also had a bug fix where
Renesas controller would sleep in atomic context while doing DMA transfers from
a tasklet. There were also a set of minor cleanups.
The FSL UDC also had a scheduling in atomic context bug fix, but that's all.
Thanks to Sebastian, the dummy_hcd now works better than ever with support for
scatterlists and streams. Sebastian also added SuperSpeed descriptors to the
serial gadgets.
The highlight on this merge is the addition of a generic API for mapping and
unmapping usb_requests. This will avoid code duplication on all UDC controllers
and also kills all the defines for DMA_ADDR_INVALID which UDC controllers
sprinkled around. A few of the UDC controllers were already converted to use
this new API.
Conflicts:
drivers/usb/dwc3/gadget.c
those routines have everything we need to map/unmap
USB requests and it's better to use them.
In order to achieve that, we had to add a simple
change on how we allocate and use our setup buffer;
we cannot allocate it from coherent anymore otherwise
the generic map/unmap routines won't be able to easily
know that the GetStatus request already has a DMA
address.
Signed-off-by: Felipe Balbi <balbi@ti.com>
this will get rid of a useless memcpy on
IRQ handling, thus improving driver performance.
Tested with OMAP5430 running g_mass_storage on
SuperSpeed and HighSpeed.
Note that we are removing the little endian access
of the TRB and all accesses will be in System endianness,
if there happens to be a system in BE, bit 12 of GSBUSCFG0
should be set so that HW does byte invariant BE accesses
when fetching TRBs.
Signed-off-by: Felipe Balbi <balbi@ti.com>
When host requests us to enter a test mode,
we cannot directly enter the test mode before
Status Phase is completed, otherwise the core
will never be able to deliver the Status ZLP
to host, because it has already entered the
requested Test Mode.
In order to fix the error, we move the actual
start of Test Mode right after we receive
Transfer Complete event of the status phase.
Signed-off-by: Gerard Cauvy <g-cauvy1@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We need to dynamically re-size TxFifos for the
cases where default values will not do.
While at that, we create a simple function which,
for now, will just allocate one full packet fifo
space for each of the enabled endpoints.
This can be improved later in order to allow for
better throughput by allocating more space for
endpoints which could make good use of that like
isochronous and bulk.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Mass Storage gadget will take some time to handle
the SetConfiguration request, but even on those
cases we should move to CONFIGURED state.
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are some situations were we might need to
enable USB Test Modes without having access to a
Host stack. In such situations we cannot rely
solely on USB Control Messages to enable test
features.
For those cases, we will also allow test mode
to be enabled via debugfs and this patch is a
preparation for that.
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 34c60a7 (usb: dwc3: ep0: tidy up Pending
Request handling) introduced a compile warning
by leaving an unused variable.
This patch fixes that warning:
drivers/usb/dwc3/ep0.c: In function ‘__dwc3_gadget_ep0_queue’:
drivers/usb/dwc3/ep0.c:129:8: warning: unused variable ‘type’
[-Wunused-variable]
Signed-off-by: Felipe Balbi <balbi@ti.com>
The way our code was written, we should never have
a DWC3_EP_PENDING_REQUEST flag set out of a Data Phase
and the code in __dwc3_gadget_ep0_queue() did not
reflect that situation properly.
Tidy up that case to avoid any possible mistakes
when starting requests for IRQs which are long
gone.
Cc: stable@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is a very small possibility (previously unimagined
by us) that the whole Mass Storage delayed status happens
rather early, before we even get our XferNotReady event.
In that case, we will be queueing a request to ep0 while
we're still on Setup Phase and we would be waiting for
another usb_ep_queue() forever.
Handle such cases by clearing dwc->delayed_status so that
we start control status from the next XferNotReady like
there was no wait for Delayed Status.
Tested against Linux 3.2-rc3 and USB30CV tool from USB-IF
(on a Windows XP with USB3 PCIe card).
Signed-off-by: Felipe Balbi <balbi@ti.com>
previous commit fixed part of it but it was still
calling usb_ep_queue() from IRQ context without
loosing locks. That cannot be done otherwise we will
have a recursive locking.
Also, we need to assign the 'dep' pointer on
dwc->ep0_usb_req otherwise we will have a NULL
pointer dereference on dwc3_map_buffer_to_dma().
Signed-off-by: Felipe Balbi <balbi@ti.com>
Instead of special functions and shortcuts for sending our internal
answers to the host we started doing what the gadget does and used the
public API for this. Since we only were using a few fields the
usb_request was enough. Later added the list handling in order to
synchronize the host / gadget events and now we require to have the
dwc3_request struct around our usb_request or else we touch memory that
does not belong to us. So this patch does this.
Reported-by: Partha Basak <p-basak2@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
DWC3 revisions <1.88a have an issue which would
case a missing Disconnect event if cable is
disconnected while there's a Setup packet
pending the FIFO.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since the re-worked ep0 handling (which uses HW's hints to recognize the ep0
status) we lost the delayed status handling. This is used by the file and mass
storage gadget to gain some extra time so setup its internal status before it
can proceed further requests.
In particular the storage gadget does nothing on USB_REQ_SET_CONFIGURATION but
wakes up a thread which handles the request. If the udc driver continues ep0
handling before the thread did its work then then endpoint is not yet
configured and further requests will fail. Once the gadget is ready, it will
enqueue an empty packet which is used for synchronization.
In order to fix this issue, the patch does the following:
Set ->delayed_status once the delayed_status has been notices and do not
continue on the next XferNotReady event. We will continues ep0 processing once
the gadget enqueued the zero packet for synchronization.
A cleaner approach would be to enforce the gadget to enqueue an empty
(zero) request even for the status phase but this would do for now.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We wait for the XferNotReady before we start the transfer and by then we
know ep0 state in which we supposed to be.
This is some cleanup work for the following patch in which we require to
know the ep0 state before the transfer completes.
While here, also change the argument to dwc3_ep0_do_control_status() so
we don't require the complete event structure but only the required
piece of information.
Inspired-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
sparse caught three mistakes on this driver,
fix them:
drivers/usb/dwc3/ep0.c:806:29: warning: duplicate const
drivers/usb/dwc3/debugfs.c:481:15: warning: symbol 'dwc3_debugfs_init' \
was not declared. Should it be static?
drivers/usb/dwc3/debugfs.c:518:16: warning: symbol 'dwc3_debugfs_exit' \
was not declared. Should it be static?
Signed-off-by: Felipe Balbi <balbi@ti.com>
There were a few coding style issues with this driver
which are now fixed:
drivers/usb/dwc3/debugfs.c:48: WARNING: Use #include \
<linux/uaccess.h> instead of <asm/uaccess.h>
drivers/usb/dwc3/debugfs.c:484: ERROR: space required \
before the open brace '{'
drivers/usb/dwc3/ep0.c:261: WARNING: line over 80 characters
drivers/usb/dwc3/ep0.c:287: WARNING: suspect code indent \
for conditional statements (16, 23)
drivers/usb/dwc3/gadget.c:749: WARNING: line over 80 characters
drivers/usb/dwc3/gadget.c:1267: WARNING: line over 80 characters
drivers/usb/dwc3/gadget.h:116: WARNING: line over 80 characters
drivers/usb/dwc3/io.h:42: WARNING: Use #include \
<linux/io.h> instead of <asm/io.h>
Signed-off-by: Felipe Balbi <balbi@ti.com>
