This commit fixes the following compile warnings.
From v2.6.37-rc2/m68k/m68k-allmodconfig, v2.6.37-rc2/powerpc/powerpc-randconfig:
drivers/hwmon/lis3lv02d_i2c.c:222: warning: 'lis3_i2c_runtime_suspend' defined but not used
drivers/hwmon/lis3lv02d_i2c.c:231: warning: 'lis3_i2c_runtime_resume' defined but not used
Seen if CONFIG_PM_RUNTIME is not set.
From v2.6.37-rc2/sh4/sh-allyesconfig:
drivers/hwmon/lis3lv02d_i2c.c:191: warning: 'lis3lv02d_i2c_suspend' defined but not used
drivers/hwmon/lis3lv02d_i2c.c:201: warning: 'lis3lv02d_i2c_resume' defined but not used
Seen if CONFIG_PM is set but CONFIG_PM_SLEEP is not.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
This patch fixes the following compile warning.
drivers/hwmon/i5k_amb.c:500: warning: 'i5k_amb_ids' defined but not used
The warning is seen if the driver is built into the kernel (not as module).
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
On the W83795ADG, there's a single pin for BEEP and OVT#, so you
can't have both. Check the configuration and don't create beep
attributes when BEEP pin is not available.
The W83795G has a dedicated BEEP pin so the functionality is always
available there.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
When asked to clear the intrusion alarm, do so immediately. We have to
invalidate the cache to make sure the new status will be read. But we
also have to read from the status register once to clear the pending
alarm, as writing to CLR_CHS surprising won't clear it automatically.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
We can't read the intrusion state from the real-time alarm registers
as we do for all other alarm flags, because real-time alarm bits don't
stick (by definition) and the intrusion state has to stick until
explicitly cleared (otherwise it has little value.)
So we have to use the interrupt status register instead, which is read
from the same address but with a configuration bit flipped in another
register.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Don't expose raw register values to user-space. Decode and encode
temperature channels selected as temperature sources as needed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Temperature sources are not correlated directly with temperature
channels. A look-up table is required to find out which temperature
sources can be used depending on which temperature channels (both
analog and digital) are enabled.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Expose fan control method (DC vs. PWM) using the standard sysfs
attributes. I've made it read-only as the board should be wired for
a given mode, the BIOS should have set up the chip for this mode, and
you shouldn't have to change it. But it would be easy enough to make
it changeable if someone comes up with a use case.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
There were two bugs:
* Speed cruise mode was improperly reported for all fans but fan1.
* Fan control method (PWM vs. DC) was mixed with the control mode.
It will be added back as a separate attribute, as per the standard
sysfs interface.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
This clears the following build-time warnings I was seeing:
drivers/hwmon/lm95241.c: In function "set_interval":
drivers/hwmon/lm95241.c:132:15: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_max2":
drivers/hwmon/lm95241.c:278:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_max1":
drivers/hwmon/lm95241.c:277:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_min2":
drivers/hwmon/lm95241.c:249:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_min1":
drivers/hwmon/lm95241.c:248:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_type2":
drivers/hwmon/lm95241.c:220:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_type1":
drivers/hwmon/lm95241.c:219:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
This also fixes a small race in set_interval() as a side effect: by
working with a temporary local variable we prevent data->interval from
being accessed at a time it contains the interval value in the wrong
unit.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Davide Rizzo <elpa.rizzo@gmail.com>
My old mail address doesn't exist anymore. This changes all occurrences
to my new address.
Signed-off-by: Hans J. Koch <hjk@hansjkoch.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
In current implementation, the sysfs entries is not removed before return -ENODEV.
Creating the sysfs attribute should be the last thing done by the function,
after all the rest has been successful.
Otherwise there is a small window during which user-space can access the attribute
but the driver isn't ready to deal with the requests.
Fix it by moving sysfs_create_group to be the last thing done by the function.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Return proper error if i2c_check_functionality reports
the adapter does not support the capability we need.
Also remove unneeded initialization for err variable.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
adapter->id is deprecated and not set by any adapter driver, so this
was certainly not what the author wanted to use. adapter->nr maybe,
but as dev_err() already includes this value, as well as the client's
address, there's no point repeating them. Better print a simple error
message in plain English words.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add support for the IT8721F/IT8758E. These new chips differ from the
older IT87xxF chips in the following ways:
* ADC LSB is 12 mV instead of 16 mV.
* PWM values are 8-bit instead of 7-bit.
There are other minor changes we don't have to care about in the
driver.
Another change is that we will handle internal voltage scaling in the
driver instead of delegating the work to user-space.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Move conversion functions until after structure defintions. This is
needed for future changes which make use of the structures in the
conversion funtcions.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Remove the dependency on EXPERIMENTAL for all drivers which are in
the kernel tree for a long time, are known to work properly and for
which we have documentation.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Corentin Labbe <corentin.labbe@geomatys.fr>
Cc: Riku Voipio <riku.voipio@iki.fi>
Cc: Juerg Haefliger <juergh@gmail.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The ADT7468 supports a high-frequency PWM output mode where all PWM
outputs are driven by a 22.5 kHz clock. Add support for this mode, and
document it, as it may surprise the user that setting one PWM output
frequency also affects the other PWM outputs.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The ADT7468 uses the same frequency table as the ADT7463.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
Cc: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
We can mark normal_i2c const. Almost all drivers do that already, so
fix the 3 remaining ones before they are used as (bad) examples for
new drivers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: George Joseph <george.joseph@fairview5.com>
Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com>
The ams driver isn't a hardware monitoring driver, so it shouldn't
live under driver/hwmon. drivers/macintosh seems much more
appropriate, as the driver is only useful on PowerBooks and iBooks.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Stelian Pop <stelian@popies.net>
Cc: Michael Hanselmann <linux-kernel@hansmi.ch>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
The PCF8591 can't be detected, don't even try. There are plenty of
other means to instantiate i2c devices these days.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Register PCF8591 devices as hwmon devices. There's little point in
implementing the standard sysfs interface if we don't register it in
a way libsensors will pick it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Follow the standard attribute naming for the chassis intrusion
feature. I couldn't test the beeping (my board apparently doesn't do
that) but the alarm works fine.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The fan control feature of the w83795 driver is insufficiently
reviewed and tested for public consumption at this time, so make it
optional and disabled by default. We will change the default when
review and testing is deemed sufficient. Ultimately the option will
go away.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
I've made so many changes to the w83795 driver that it's only fair to
list myself as a co-author. I'll also maintain the driver for some
time. There's more work needed on the driver for sure.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cleanups suggested by Guenter Roeck, falling into 4 categories:
* Swapping test orders, because if (var == CONSTANT) is much easier to
read than if (CONSTANT == var).
* Simplifying comparisons with 0.
* Dropping unneeded masks.
* Dropping unneeded parentheses and curly braces.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
When we don't need the client pointer, calling dev_get_drvdata() is
more efficient that calling to_i2c_client() and then
i2c_get_clientdata().
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Wait until we need the pwm config register values, instead of
pre-reading them. This saves over 1 second on modprobe on my test
system.
Obviously this time is added when first accessing pwm config
attributes, however not everybody will use them, so it seems unfair
to slow down driver loading (and thus boot) for an optional feature.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Wait until we need the limit register values, instead of pre-reading
them. This saves 544 ms on modprobe on my test system. Obviously this
time is added when first running "sensors" or any other monitoring
application, but I think it is better than slowing down the boot.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Move initial register reads out of probe, to dedicated functions.
This makes the code clearer, and will be needed if we want to delay
calling these functions until they are needed, or want to call them
periodically.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cascaded conditionals are inefficient. Reorder the fields so that
PWM register addresses can be computed more efficiently.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
There is no point in reading registers during initialization if we
will refresh the values in the update function later. This is only
slowing down the driver loading with no benefit, stop doing it.
This change saves 480 ms on driver load on my test system.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
All 3 temperature sensor type sysfs functions (show_temp_mode,
store_temp_mode and show_dts_mode) can be simplified. We don't
create these files when the correponding input isn't in temperature
monitoring mode, so there is no point in handling that case.
Likewise, we don't allow changing inputs from temperature to voltage,
so the code handling this case is dead and can be removed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
VRLSB_SHIFT is a non-sense, the actual shift depends on the sensor
type (fans need 4, other sensors need 6). Get rid of it to prevent
any confusion. Also get rid of the useless masking, the meaningful
bits are always the MSb so there's nothing to mask out after
shifting.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Shorten driver load time by avoiding duplicate register access during
initialization. This saves 112 ms on modprobe on my test system.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Handle beep_enable just like all other beep bits. It doesn't need
anything special, so let's avoid redundant code. This also saves a
duplicate register read at initialization time.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The PWM duty cycle frequenty attributes are improperly named
(fanN_div instead of pwmN_div) and contain raw values instead of
actual frequencies. Rename them and fix their contents.
Also improve the logic when the user asks for a new frequency, to
always pick the closest supported frequency. The algorithm could
certainly be optimized, but the operation is infrequent enough that
I don't think it's worth the effort.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The W83795G can be configured to set the in0, in1 and/or in2 voltage
limits dynamically based on VID input pins. Switch the respective
sysfs attributes to read-only.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
