Use DEFINE_PCI_DEVICE_TABLE() so we get place PCI ids table into correct section
in every case.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only files where David Miller is the primary git-signer.
wireless, wimax, ixgbe, etc are not modified.
Compile tested x86 allyesconfig only
Not all files compiled (not x86 compatible)
Added a few > 80 column lines, which I ignored.
Existing checkpatch complaints ignored.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As noticed by Alan Stern, there is still one issue with the driver:
we disable PCI IRQ on suspend, but other devices on the same IRQ
line might still need the IRQ enabled to suspend properly.
Nowadays, PCI core handles all power management work by itself, with
one condition though: if we use dev_pm_ops. So, rework the driver to
only quiesce 3c59x internal logic on suspend, while PCI core will
manage PCI device power state with IRQs disabled.
Suggested-by: Rafael J. Wysocki <rjw@sisk.pl>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following trace pops up if we try to suspend with 3c59x ethernet NIC
brought down:
root@b1:~# ifconfig eth16 down
root@b1:~# echo mem > /sys/power/state
...
3c59x 0000:00:10.0: suspend
3c59x 0000:00:10.0: PME# disabled
Trying to free already-free IRQ 48
------------[ cut here ]------------
Badness at c00554e4 [verbose debug info unavailable]
NIP: c00554e4 LR: c00554e4 CTR: c019a098
REGS: c7975c60 TRAP: 0700 Not tainted (2.6.31-rc4)
MSR: 00021032 <ME,CE,IR,DR> CR: 28242422 XER: 20000000
TASK = c79cb0c0[1746] 'bash' THREAD: c7974000
...
NIP [c00554e4] __free_irq+0x108/0x1b0
LR [c00554e4] __free_irq+0x108/0x1b0
Call Trace:
[c7975d10] [c00554e4] __free_irq+0x108/0x1b0 (unreliable)
[c7975d30] [c005559c] free_irq+0x10/0x24
[c7975d40] [c01e21ec] vortex_suspend+0x70/0xc4
[c7975d60] [c017e584] pci_legacy_suspend+0x58/0x100
This is because the driver manages interrupts without checking for
netif_running().
Though, there are few other issues with suspend/resume in this driver.
The intention of calling free_irq() in suspend() was to avoid any
possible spurious interrupts (see commit 5b039e681b
"3c59x PM fixes"). But,
- On resume, the driver was requesting IRQ just after pci_set_master(),
but before vortex_up() (which actually resets 3c59x chips).
- Issuing free_irq() on a shared IRQ doesn't guarantee that a buggy
HW won't trigger spurious interrupts in another driver that
requested the same interrupt. So, if we want to protect from
unexpected interrupts, then on suspend we should issue disable_irq(),
not free_irq().
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We found this old card which was not supported, and physically
looks similar to the other 3C905B we have (9055).
After adding the IDs it seems to work fine (MII report, dhcp, scp, ...)
Acked-by: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following build failure with gcc 3.2:
CC [M] drivers/net/3c59x.o
drivers/net/3c59x.c:2726:1: directives may not be used inside a macro argument
drivers/net/3c59x.c:2725:59: unterminated argument list invoking macro "pr_err"
drivers/net/3c59x.c: In function `dump_tx_ring':
drivers/net/3c59x.c:2727: implicit declaration of function `pr_err'
drivers/net/3c59x.c:2731: syntax error before ')' token
Apparently gcc 3.2 doesn't like #if interleaved with a macro call.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is the result of an automatic spatch transformation to convert
all ndo_start_xmit() return values of 0 to NETDEV_TX_OK.
Some occurences are missed by the automatic conversion, those will be
handled in a seperate patch.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert magic values 1 and -1 to NETDEV_TX_BUSY and NETDEV_TX_LOCKED respectively.
0 (NETDEV_TX_OK) is not changed to keep the noise down, except in very few cases
where its in direct proximity to one of the other values.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since dev->power.should_wakeup bit is used by the PCI core to
decide whether the device should wake up the system from sleep
states, set this bit by calling device_set_wakeup_enable().
This restores proper WOL for the 3c59x driver.
Reported-and-tested-by: Graeme Wilford <gwilford@gmail.com>
Reported-by: Gunnar Degnbol <degnbol@danbbs.dk>
Signed-off-by: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have some reasons to kill netdev->priv:
1. netdev->priv is equal to netdev_priv().
2. netdev_priv() wraps the calculation of netdev->priv's offset, obviously
netdev_priv() is more flexible than netdev->priv.
But we cann't kill netdev->priv, because so many drivers reference to it
directly.
This patch is a safe convert for netdev->priv to netdev_priv(netdev).
Since all of the netdev->priv is only for read.
But it is too big to be sent in one mail.
I split it to 4 parts and make every part smaller than 100,000 bytes,
which is max size allowed by vger.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Drivers need not do it any more.
Some cases had to be skipped over because the drivers
were making use of the ->last_rx value themselves.
Signed-off-by: David S. Miller <davem@davemloft.net>
This converts pretty much everything to print_mac. There were
a few things that had conflicts which I have just dropped for
now, no harm done.
I've built an allyesconfig with this and looked at the files
that weren't built very carefully, but it's a huge patch.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix possible bug where end of receive buffer could be overwritten.
The allocation needs to allow for the reserved space. This would only happen
if device received packet greater than Ethernet standard MTU.
Change this driver to use netdev_alloc_skb rather than setting skb->dev
directly. For the initial allocation it doesn't need to be GFP_ATOMIC.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This changes vortex_prob1() to handle pci_name() now returning a
constant string.
Cc: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use net_device_stats from net_device structure instead of local.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Acked-by: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The ethernet card 3c980-TX needs a mdio_sync() to initialize the ethernet
properly. This is forced by adding an EXTRA_PREAMBLE to its drv_flags.
Without this, the driver did not reconnect after a link loss.
Signed-off-by: Gunnar Larisch <Gunnar.Larisch@gmx.de>
Acked-by: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Simple compile warning fix. (against 2.6.23-git12)
Thanks,
Badari
vortex_up() should initialize 'err' for a successful return.
drivers/net/3c59x.c: In function `vortex_up':
drivers/net/3c59x.c:1494: warning: `err' might be used uninitialized in this function
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some NICs (3c905B) can not generate PME in power state PCI_D0, while others
like 3c905C can. Call pci_enable_wake() with PCI_D3hot should give proper
WOL for 3c905B.
Signed-off-by: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Tested-by: Harry Coin <hcoin@n4comm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
These have been superceded by the new ->get_sset_count() hook.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it. The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.
[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check return of pci_enable_device in vortex_up().
Also modify vortex_up to return error to callers. Handle failure of
vortex_up in vortex_open and vortex_resume.
Signed-off-by: Mark Hindley <mark@hindley.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A special sequence of ifconfig up/down and plug/unplug the cable can break
the duplex configuration of the driver.
Setting
vp->mii.full_duplex = vp->full_duplex
in vortex_up should fix this.
Addresses Bug 8575 3c59x duplex configuration broken
http://bugzilla.kernel.org/show_bug.cgi?id=8575
Cc: Martin Buck <mb-tmp-ohtmvyyn.xreary.bet@gromit.dyndns.org>
Signed-off-by: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Cc: Natalie Protasevich <protasnb@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
All drivers implement ethtool get_perm_addr the same way -- by calling
the generic function. So we can inline the generic function into the
caller and avoid going through the drivers.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 3cSOHO100-TX needs a mdio_sync() before mdio_read() to read the MII
transceiver registers properly. Adding EXTRA_PREAMBLE to drv_flags of the
3cSOHO100-TX will force this.
This problem exists already for years (I checked back to 2.6.8).
Setting duplex for the 3cSOHO100-TX was more or less a random process.
Till 2.6.15 it was more likely that the diver ends up in half
duplex mode, after the code change in 2.6.16 it was more likely
to end up in full duplex mode. I wonder why nobody noticed this earier.
Hopefully addresses
Bug 7454 3c59x (3cSOHO100-TX Hurricane) slow network bug
http://bugzilla.kernel.org/show_bug.cgi?id=7454
and
Bug 3654 3cSOHO100-TX: No MII transceiver present
http://bugzilla.kernel.org/show_bug.cgi?id=3654
Cc: Jonas Sandberg <jonassa@gmail.com>
Cc: Jon Sanchez <bugs@niluje.net>
Signed-off-by: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove broken URLs (www.scyld.com) from network drivers' logging output.
URLs in comments and other strings are left intact.
Signed-off-by: Markus Dahms <dahms@fh-brandenburg.de>
Acked-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Alan Cox <alan@redhat.com>
igned-off-by: Adrian Bunk <bunk@stusta.de>
One less thing for drivers writers to worry about.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WARNING: drivers/net/3c59x.o - Section mismatch: reference to .init.text: from .text between 'vortex_eisa_probe' (at offset 0x4580) and 'vortex_eisa_remove'
WARNING: drivers/net/3c59x.o - Section mismatch: reference to .init.text: from .text between 'vortex_eisa_probe' (at offset 0x4584) and 'vortex_eisa_remove'
WARNING: drivers/net/3c59x.o - Section mismatch: reference to .init.text: from .text between 'vortex_eisa_probe' (at offset 0x4588) and 'vortex_eisa_remove'
WARNING: drivers/net/3c59x.o - Section mismatch: reference to .init.text: from .text between 'vortex_eisa_probe' (at offset 0x458c) and 'vortex_eisa_remove'
Fixed by:
o move definition of vortex_eisa_driver below the functions it references.
o remove now unnecessary prototypes for vortex_eisa_probe and
vortex_eisa_remove.
o Make vortex_eisa_probe an __init function.
o Make vortex_eisa_remove a __devexit function.
o Wrap vortex_eisa_driver reference to vortex_eisa_remove with
__devexit_p().
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
drivers/net/3c59x.c | 28 +++++++++++++---------------
1 file changed, 13 insertions(+), 15 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Handle pci_enable_device() failure while resuming, we can safely exit here.
Signed-off-by: Monakhov Dmitriy <dmonakhov@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/net/3c59x.c::poll_vortex() contains local_irq_disable() after
local_save_flags(). Turn it into local_irq_save().
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
Add modalias attribute support for the almost forgotten now EISA bus and
(at least some) EISA-aware modules.
The modalias entry looks like (for an 3c509 NIC):
eisa:sTCM5093
and the in-module alias like:
eisa:sTCM5093*
The patch moves struct eisa_device_id declaration from include/linux/eisa.h
to include/linux/mod_devicetable.h (so that the former now #includes the
latter), adds proper MODULE_DEVICE_TABLE(eisa, ...) statements for all
drivers with EISA IDs I found (some drivers already have that DEVICE_TABLE
declared), and adds recognision of __mod_eisa_device_table to
scripts/mod/file2alias.c so that proper modules.alias will be generated.
There's no support for /lib/modules/$kver/modules.eisamap, as it's not used
by any existing tools, and because with in-kernel modalias mechanism those
maps are obsolete anyway.
The rationale for this patch is:
a) to make EISA bus to act as other busses with modalias
support, to unify driver loading
b) to foget about EISA finally - with this patch, kernel
(who still supports EISA) will be the only one who knows
how to choose the necessary drivers for this bus ;)
[akpm@osdl.org: fix the kbuild bit]
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Acked-the-net-bits-by: Jeff Garzik <jeff@garzik.org>
Acked-the-tulip-bit-by: Valerie Henson <val_henson@linux.intel.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (217 commits)
net/ieee80211: fix more crypto-related build breakage
[PATCH] Spidernet: add ethtool -S (show statistics)
[NET] GT96100: Delete bitrotting ethernet driver
[PATCH] mv643xx_eth: restrict to 32-bit PPC_MULTIPLATFORM
[PATCH] Cirrus Logic ep93xx ethernet driver
r8169: the MMIO region of the 8167 stands behin BAR#1
e1000, ixgb: Remove pointless wrappers
[PATCH] Remove powerpc specific parts of 3c509 driver
[PATCH] s2io: Switch to pci_get_device
[PATCH] gt96100: move to pci_get_device API
[PATCH] ehea: bugfix for register access functions
[PATCH] e1000 disable device on PCI error
drivers/net/phy/fixed: #if 0 some incomplete code
drivers/net: const-ify ethtool_ops declarations
[PATCH] ethtool: allow const ethtool_ops
[PATCH] sky2: big endian
[PATCH] sky2: fiber support
[PATCH] sky2: tx pause bug fix
drivers/net: Trim trailing whitespace
[PATCH] ehea: IBM eHEA Ethernet Device Driver
...
Manually resolved conflicts in drivers/net/ixgb/ixgb_main.c and
drivers/net/sky2.c related to CHECKSUM_HW/CHECKSUM_PARTIAL changes by
commit 84fa7933a3 that just happened to be
next to unrelated changes in this update.
Replace CHECKSUM_HW by CHECKSUM_PARTIAL (for outgoing packets, whose
checksum still needs to be completed) and CHECKSUM_COMPLETE (for
incoming packets, device supplied full checksum).
Patch originally from Herbert Xu, updated by myself for 2.6.18-rc3.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
As I promised last week, here is the first pass at removing all
unnecessary printk's that exist in network device drivers currently in
promiscuous mode. The duplicate messages are not needed so they have
been removed. Some of these drivers are quite old and might not need an
update, but I did them all anyway.
I am currently auditing the remaining conditional printk's and will send
out a patch for those soon.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
