Printing IRQ # using "%x" and "%u" unsigned formats isn't quite correct as
'ndev->irq' is of type *int*, so the "%d" format needs to be used instead.
While fixing this, beautify the dev_info() message in rcar_can_probe() a bit.
Fixes: fd1159318e ("can: add Renesas R-Car CAN driver")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
rcar_can_probe() regards 0 as a wrong IRQ #, despite platform_get_irq() that it
calls returns negative error code in that case. This leads to the following
being printed to the console when attempting to open the device:
error requesting interrupt fffffffa
because rcar_can_open() calls request_irq() with a negative IRQ #, and that
function naturally fails with -EINVAL.
Check for the negative error codes instead and propagate them upstream instead
of just returning -ENODEV.
Fixes: fd1159318e ("can: add Renesas R-Car CAN driver")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Conflicts:
drivers/net/ethernet/mellanox/mlx4/main.c
net/packet/af_packet.c
Both conflicts were cases of simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Manfred Schlaegl here
http://marc.info/?l=linux-netdev&m=143482089824232&w=2
commit 514ac99c64 "can: fix multiple delivery of a single CAN frame for
overlapping CAN filters" requires the skb->tstamp to be set to check for
identical CAN skbs.
As net timestamping is influenced by several players (netstamp_needed and
netdev_tstamp_prequeue) Manfred missed a proper timestamp which leads to
CAN frame loss.
As skb timestamping became now mandatory for CAN related skbs this patch
makes sure that received CAN skbs always have a proper timestamp set.
Maybe there's a better solution in the future but this patch fixes the
CAN frame loss so far.
Reported-by: Manfred Schlaegl <manfred.schlaegl@gmx.at>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch corrects addresses of acceptance filters. These registers are not in
use, but values should be correct. Tested with MCP2515 and am3352 and also
checked datasheets for MCP2515 and MCP2510.
Signed-off-by: Tomas Krcka <tomas.krcka@nkgroup.cz>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Four minor merge conflicts:
1) qca_spi.c renamed the local variable used for the SPI device
from spi_device to spi, meanwhile the spi_set_drvdata() call
got moved further up in the probe function.
2) Two changes were both adding new members to codel params
structure, and thus we had overlapping changes to the
initializer function.
3) 'net' was making a fix to sk_release_kernel() which is
completely removed in 'net-next'.
4) In net_namespace.c, the rtnl_net_fill() call for GET operations
had the command value fixed, meanwhile 'net-next' adjusted the
argument signature a bit.
This also matches example merge resolutions posted by Stephen
Rothwell over the past two days.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces a open coded variant of a "mailbox code" definition by an
existing define, improves code readability.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds a short documentation snippet about the mailbox organization as
it's regularly not correct in freescale's datasheets.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Flexcan V10 and newer are able to receive RTR frames in a MB. Older versions
are not. Those should use flexcan in FIFO mode.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In our department we are using some older Janz ICAN3-modules in our dekstop
pcs. There we have slightly different carrier boards than the janz-cmodio
supported in the kernel sources, called CAN-PCI2 with two submodules. But the
pci configuration regions are identical. So extending the supported pci devices
to the corresponding device ids is sufficient to get the drivers working.
* The old ICAN3-modules with firmware 1.28 need more then 250ms for the restart
after reset. I've increased the timeout to 500ms.
* The janz_ican3 module uses the raw can services of the Janz-firmware, this
means firmware must be ICANOS/2. Our ICAN3-modules are equipped with
CAL/CANopen-firmware, so I must use the appropriate commands for the layer
management services.
Te driver detects the firmware after module reset and selects the commands
matching the firmware. This affects the bus on/off-command
(ican3_set_bus_state) and the configuration of the bittiming
(ican3_set_bittiming). For better diagnostics the detected firmware string is
presented as sysfs attribute (fwinfo).
Signed-off-by: Andreas Gröger <andreas24groeger@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Using IDR_SRR in RXFIFO_ID to test for the presence of data is only
valid for standard frames. For extended frames the bit is always 1 and
IDR_RTR should be used instead. This patch switches the check to use
CAN_RTR_FLAG which is correctly set when reading the ID.
The patch also changes the DW1/DW2 to be read unconditionally, since
this is necessary to remove the frame from the RXFIFO.
Signed-off-by: Jeppe Ledet-Pedersen <jlp@gomspace.com>
Acked-by: Kedareswara rao Appana <appanad@xilinx.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If NO_DMA=y:
drivers/built-in.o: In function `grcan_free_dma_buffers':
grcan.c:(.text+0x2d7716): undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `grcan_allocate_dma_buffers':
grcan.c:(.text+0x2d779c): undefined reference to `dma_alloc_coherent'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/asix_common.c
drivers/net/usb/sr9800.c
drivers/net/usb/usbnet.c
include/linux/usb/usbnet.h
net/ipv4/tcp_ipv4.c
net/ipv6/tcp_ipv6.c
The TCP conflicts were overlapping changes. In 'net' we added a
READ_ONCE() to the socket cached RX route read, whilst in 'net-next'
Eric Dumazet touched the surrounding code dealing with how mini
sockets are handled.
With USB, it's a case of the same bug fix first going into net-next
and then I cherry picked it back into net.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch silences the compiler warning:
drivers/net/can/usb/peak_usb/pcan_usb_fd.c: In function 'pcan_usb_fd_send_cmd':
drivers/net/can/usb/peak_usb/pcan_usb_fd.c:185:6: warning: 'err' may be used uninitialized in this function [-Wuninitialized]
by initialising the variable as 0.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The struct ems_cpc_msg describes the a message received from the USB device,
which uses little endian byte order. This patch marks the timestamp in struct
ems_cpc_msg accordingly.
Acked-by: Gerhard Uttenthaler <uttenthaler@ems-wuensche.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The device expects the CAN ID in little endian format.
Signed-off-by: Gerhard Uttenthaler <uttenthaler@ems-wuensche.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Change __raw accesors to endian agnostic versions to allow the driver
to work properly on big endian systems.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The hnd field of the structs does not need to be __le32: the
device just returns the value without using it itself.
Signed-off-by: Thomas Körper <thomas.koerper@esd.eu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add <ifname>-rxtx trigger, that will be activated both for tx
as rx events. This trigger mimics "activity" LED for Ethernet
devices.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Use can-dev's unregister_candev() instead of directly calling
networking unregister_netdev(). While both are functionally
equivalent, unregister_candev() might do extra stuff in the
future than just calling networking layer unregistration code.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Return EPROBE_DEFER if Regulator returns EPROBE_DEFER
If the Flexcan driver is built into kernel and a regulator is used to
enable the CAN transceiver, the Flexcan driver may not use the regulator.
When initializing the Flexcan device with a regulator defined in the device
tree, but not initialized, the regulator subsystem returns EPROBE_DEFER, hence
the Flexcan init fails.
The solution for this is to return EPROBE_DEFER if regulator is not initialized
and wait until the regulator is initialized.
Signed-off-by: Andreas Werner <kernel@andy89.org>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Making sure that the bus-off state gets passed to can_change_state().
Signed-off-by: Andri Yngvason <andri.yngvason@marel.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The PCAN USB (pro) FD adapters with firmware versions > 2.x support the
switching between ISO (default) and non-ISO conform bitstreams on the CAN bus.
The setting for the 2.x firmware adapters can be modified with the 'ip' tool
from the iproute2 package (option: fd-non-iso [on|off]).
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The PUCAN_CMD_RX_FRAME_(ENABLE|DISABLE) command has extended its purpose
and was therefore renamed to PUCAN_CMD_SET_(EN|DIS)_OPTION.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
smatch detected the following issue:
drivers/net/can/usb/gs_usb.c:904 gs_usb_probe() error:
potential null dereference 'dev'. (kzalloc returns null)
Add a check for null return from kzalloc and return -ENOMEM
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
USB endpoint's wMaxPacketSize field is an le16 entity. Use
appropriate le16_to_cpu macros to maintain endian independence.
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Current driver code arbitrarily assumes a max outstanding tx
value of 16 parallel transmissions. Meanwhile, the device
firmware provides its actual maximum inside its reply to the
CMD_GET_SOFTWARE_INFO message.
Under heavy tx traffic, if the interleaved transmissions count
increases above the limit reported by firmware, the firmware
breaks up badly, reports a massive list of internal errors, and
the candump traces hardly matches the actual frames sent and
received.
On the other hand, in certain models, the firmware can support
up to 48 tx URBs instead of just 16, increasing the driver
throughput by two-fold and reducing the possibility of -ENOBUFs.
Thus dynamically set the driver's max tx URBs value according
to firmware replies.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
net/core/sysctl_net_core.c
net/ipv4/inet_diag.c
The be_main.c conflict resolution was really tricky. The conflict
hunks generated by GIT were very unhelpful, to say the least. It
split functions in half and moved them around, when the real actual
conflict only existed solely inside of one function, that being
be_map_pci_bars().
So instead, to resolve this, I checked out be_main.c from the top
of net-next, then I applied the be_main.c changes from 'net' since
the last time I merged. And this worked beautifully.
The inet_diag.c and sysctl_net_core.c conflicts were simple
overlapping changes, and were easily to resolve.
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of tx queue wake-up events went missing due to the
outlined scenario below. Start state is a pool of 16 tx URBs,
active tx_urbs count = 15, with the netdev tx queue open.
CPU #1 [softirq] CPU #2 [softirq]
start_xmit() tx_acknowledge()
................ ................
atomic_inc(&tx_urbs);
if (atomic_read(&tx_urbs) >= 16) {
-->
atomic_dec(&tx_urbs);
netif_wake_queue();
return;
<--
netif_stop_queue();
}
At the end, the correct state expected is a 15 tx_urbs count
value with the tx queue state _open_. Due to the race, we get
the same tx_urbs value but with the tx queue state _stopped_.
The wake-up event is completely lost.
Thus avoid hand-rolled concurrency mechanisms and use a proper
lock for contexts and tx queue protection.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Enable the xilinx driver for ARM64.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Conflicts:
drivers/net/ethernet/cadence/macb.c
Overlapping changes in macb driver, mostly fixes and cleanups
in 'net' overlapping with the integration of at91_ether into
macb in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The Kvaser firmware can only read and write messages that are
not crossing the USB endpoint's wMaxPacketSize boundary. While
receiving commands from the CAN device, if the next command in
the same URB buffer crossed that max packet size boundary, the
firmware puts a zero-length placeholder command in its place
then moves the real command to the next boundary mark.
The driver did not recognize such behavior, leading to missing
a good number of rx events during a heavy rx load session.
Moreover, a tx URB context only gets freed upon receiving its
respective tx ACK event. Over time, the free tx URB contexts
pool gets depleted due to the missing ACK events. Consequently,
the netif transmission queue gets __permanently__ stopped; no
frames could be sent again except after restarting the CAN
newtwork interface.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Upon a URB submission failure, the driver calls usb_free_urb()
but then manually frees the URB buffer by itself. Meanwhile
usb_free_urb() has alredy freed out that transfer buffer since
we're the only code path holding a reference to this URB.
Remove two of such invalid manual free().
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fixes a missing initialization of ctrlmode and ctrlmode_supported fields,
for all other CAN devices than the first one. This fix only concerns
the PCAN-USB Pro FD dual-channels CAN-FD device made by PEAK-System.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When accessing CAN network interfaces with AF_PACKET sockets e.g. by dhclient
this can lead to a skb_under_panic due to missing skb initialisations.
Add the missing initialisations at the CAN skbuff creation times on driver
level (rx path) and in the network layer (tx path).
Reported-by: Austin Schuh <austin@peloton-tech.com>
Reported-by: Daniel Steer <daniel.steer@mclaren.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Header file was in arch dependent location arch/blackfin/include/asm/bfin_can.h,
Now move and merge the useful contents of header file into driver code, note
the original header file is reserved for full registers set access test by other
code so it survives.
Signed-off-by: Aaron Wu <Aaron.wu@analog.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Blackfin was built without MMU, old driver code access the IO space by
physical address, introduce the ioremap approach to be compitable with
the common style supporting MMU enabled arch.
Signed-off-by: Aaron Wu <Aaron.wu@analog.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Replace the blackfin arch dependent style of bfin_read/bfin_write with
common readw/writew
Signed-off-by: Aaron Wu <Aaron.wu@analog.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Sending data in high speed then introducing a busoff results
in spurious BUS_ERROR events from the USBCan-II firmware directly
_after_ the triggered BUS_OFF event.
In the current CAN state handling code, this will lead to an
invalid can state of ACTIVE, ERROR, or PASSIVE even though the
CAN controller has been already shut down due to the busoff.
Guard the state handling code from such invalid events.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
return type of wait_for_completion_timeout is unsigned long not int, this patch
removes the type mismatch by moving the call into the condition.
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add support for the following new PEAK-System technik CANFD USB adapters:
PCAN-USB FD single CANFD channel USB adapter
PCAN-USB Pro FD dual CANFD channels USB adapter
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Andri Yngvason <andri.yngvason@marel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add a common function that pushes the skb in the network queue with adding
timestamps information, converted from time values read from the
PEAK USB adapters.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add support for the following new PEAK-System technik CANFD USB adapters:
PCAN-USB FD single CANFD channel USB adapter
PCAN-USB Pro FD dual CANFD channels USB adapter
The communication protocol has been developed using some mechanisms that
did exist in the PCAN-USB Pro, thus, this patch also changes some
previously static functions and data into global ones.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Upgrade PEAK-System USB adapters core to the new data structures (names) and
callbacks added for the support of the CANFD extension. This specific patch
includes changes that deal with the new struct canfd_frame.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Upgrade PEAK-System USB adapters core to the new data structures (names) and
callbacks added for the support of the CANFD extension. This specific patch
does the mandatory changes to support new data bittiming specs.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add the definition of a new callback that enable any PEAK-System CAN USB
adapter to grant read access to its Bus Error Counters value. This ability is
not supported by all the PEAK-System adapters, thus, for those, the callback
pointer will be initiaized to NULL, which is correct regarding the linux-can
device driver specs.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Export the ctrlmode_supported value from the core file to each adapter specific
file. This has been mandatory for supporting the new CANFD extension.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
A "struct peak_usb_adapter" describes a certain USB adapter, as this doesn't
change during runtime, this patch marks all USB adapter definitions as const.
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch converts the list "static struct peak_usb_adapter
*peak_usb_adapters_list[]" to be used with ARRAY_SIZE not with a NULL
termination, as the size is known during compile time.
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
CAN to USB interfaces sold by the Swedish manufacturer Kvaser are
divided into two major families: 'Leaf', and 'USBcanII'. From an
Operating System perspective, the firmware of both families behave
in a not too drastically different fashion.
This patch adds support for the USBcanII family of devices to the
current Kvaser Leaf-only driver.
CAN frames sending, receiving, and error handling paths has been
tested using the dual-channel "Kvaser USBcan II HS/LS" dongle. It
should also work nicely with other products in the same category.
List of new devices supported by this driver update:
- Kvaser USBcan II HS/HS
- Kvaser USBcan II HS/LS
- Kvaser USBcan Rugged ("USBcan Rev B")
- Kvaser Memorator HS/HS
- Kvaser Memorator HS/LS
- Scania VCI2 (if you have the Kvaser logo on top)
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Acked-by: Andri Yngvason <andri.yngvason@marel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Replace most of the can interface's state and error counters
handling with the new can-dev can_change_state() mechanism.
Suggested-by: Andri Yngvason <andri.yngvason@marel.com>
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Acked-by: Andri Yngvason <andri.yngvason@marel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Update all of the can interface's state and error counters before
trying any skb allocation that can actually fail with -ENOMEM.
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Acked-by: Andri Yngvason <andri.yngvason@marel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Conflicts:
arch/arm/boot/dts/imx6sx-sdb.dts
net/sched/cls_bpf.c
Two simple sets of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
While being in an ERROR_WARNING state, and receiving further
bus error events with error counters still in the ERROR_WARNING
range of 97-127 inclusive, the state handling code erroneously
reverts back to ERROR_ACTIVE.
Per the CAN standard, only revert to ERROR_ACTIVE when the
error counters are less than 96.
Moreover, in certain Kvaser models, the BUS_ERROR flag is
always set along with undefined bits in the M16C status
register. Thus use bitwise operators instead of full equality
for checking that register against bus errors.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
On some x86 laptops, plugging a Kvaser device again after an
unplug makes the firmware always ignore the very first command.
For such a case, provide some room for retries instead of
completely exiting the driver init code.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Send expected argument to the URB completion hander: a CAN
netdevice instead of the network interface private context
`kvaser_usb_net_priv'.
This was discovered by having some garbage in the kernel
log in place of the netdevice names: can0 and can1.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Upon receiving a hardware event with the BUS_RESET flag set,
the driver kills all of its anchored URBs and resets all of
its transmit URB contexts.
Unfortunately it does so under the context of URB completion
handler `kvaser_usb_read_bulk_callback()', which is often
called in an atomic context.
While the device is flooded with many received error packets,
usb_kill_urb() typically sleeps/reschedules till the transfer
request of each killed URB in question completes, leading to
the sleep in atomic bug. [3]
In v2 submission of the original driver patch [1], it was
stated that the URBs kill and tx contexts reset was needed
since we don't receive any tx acknowledgments later and thus
such resources will be locked down forever. Fortunately this
is no longer needed since an earlier bugfix in this patch
series is now applied: all tx URB contexts are reset upon CAN
channel close. [2]
Moreover, a BUS_RESET is now treated _exactly_ like a BUS_OFF
event, which is the recommended handling method advised by
the device manufacturer.
[1] http://article.gmane.org/gmane.linux.network/239442http://www.webcitation.org/6Vr2yagAQ
[2] can: kvaser_usb: Reset all URB tx contexts upon channel close
889b77f7fd
[3] Stacktrace:
<IRQ> [<ffffffff8158de87>] dump_stack+0x45/0x57
[<ffffffff8158b60c>] __schedule_bug+0x41/0x4f
[<ffffffff815904b1>] __schedule+0x5f1/0x700
[<ffffffff8159360a>] ? _raw_spin_unlock_irqrestore+0xa/0x10
[<ffffffff81590684>] schedule+0x24/0x70
[<ffffffff8147d0a5>] usb_kill_urb+0x65/0xa0
[<ffffffff81077970>] ? prepare_to_wait_event+0x110/0x110
[<ffffffff8147d7d8>] usb_kill_anchored_urbs+0x48/0x80
[<ffffffffa01f4028>] kvaser_usb_unlink_tx_urbs+0x18/0x50 [kvaser_usb]
[<ffffffffa01f45d0>] kvaser_usb_rx_error+0xc0/0x400 [kvaser_usb]
[<ffffffff8108b14a>] ? vprintk_default+0x1a/0x20
[<ffffffffa01f5241>] kvaser_usb_read_bulk_callback+0x4c1/0x5f0 [kvaser_usb]
[<ffffffff8147a73e>] __usb_hcd_giveback_urb+0x5e/0xc0
[<ffffffff8147a8a1>] usb_hcd_giveback_urb+0x41/0x110
[<ffffffffa0008748>] finish_urb+0x98/0x180 [ohci_hcd]
[<ffffffff810cd1a7>] ? acct_account_cputime+0x17/0x20
[<ffffffff81069f65>] ? local_clock+0x15/0x30
[<ffffffffa000a36b>] ohci_work+0x1fb/0x5a0 [ohci_hcd]
[<ffffffff814fbb31>] ? process_backlog+0xb1/0x130
[<ffffffffa000cd5b>] ohci_irq+0xeb/0x270 [ohci_hcd]
[<ffffffff81479fc1>] usb_hcd_irq+0x21/0x30
[<ffffffff8108bfd3>] handle_irq_event_percpu+0x43/0x120
[<ffffffff8108c0ed>] handle_irq_event+0x3d/0x60
[<ffffffff8108ec84>] handle_fasteoi_irq+0x74/0x110
[<ffffffff81004dfd>] handle_irq+0x1d/0x30
[<ffffffff81004727>] do_IRQ+0x57/0x100
[<ffffffff8159482a>] common_interrupt+0x6a/0x6a
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Put controller into init mode in network stop to end pending transmissions. The
issue is observed in cases when transmitted frame is not acked.
Signed-off-by: Viktor Babrian <babrian.viktor@renyi.mta.hu>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In order to be able to move the stats increment from can_bus_off() into
can_change_state(), the increment had to be moved back into code that was using
can_bus_off() but not can_change_state().
As a side-effect, this patch fixes the following bugs:
* Redundant call to can_bus_off() in c_can.
* Bus-off counted twice in xilinx_can.
Signed-off-by: Andri Yngvason <andri.yngvason@marel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
We should not touch the packet after a netif_rx: it might
get freed behind our back.
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Recent Leaf firmware versions (>= 3.1.557) do not allow to send
commands for non-existing channels. If a command is sent for a
non-existing channel, the firmware crashes.
Reported-by: Christopher Storah <Christopher.Storah@invetech.com.au>
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Flooding the Kvaser CAN to USB dongle with multiple reads and
writes in very high frequency (*), closing the CAN channel while
all the transmissions are on (#), opening the device again (@),
then sending a small number of packets would make the driver
enter an almost infinite loop of:
[....]
[15959.853988] kvaser_usb 4-3:1.0 can0: cannot find free context
[15959.853990] kvaser_usb 4-3:1.0 can0: cannot find free context
[15959.853991] kvaser_usb 4-3:1.0 can0: cannot find free context
[15959.853993] kvaser_usb 4-3:1.0 can0: cannot find free context
[15959.853994] kvaser_usb 4-3:1.0 can0: cannot find free context
[15959.853995] kvaser_usb 4-3:1.0 can0: cannot find free context
[....]
_dragging the whole system down_ in the process due to the
excessive logging output.
Initially, this has caused random panics in the kernel due to a
buggy error recovery path. That got fixed in an earlier commit.(%)
This patch aims at solving the root cause. -->
16 tx URBs and contexts are allocated per CAN channel per USB
device. Such URBs are protected by:
a) A simple atomic counter, up to a value of MAX_TX_URBS (16)
b) A flag in each URB context, stating if it's free
c) The fact that ndo_start_xmit calls are themselves protected
by the networking layers higher above
After grabbing one of the tx URBs, if the driver noticed that all
of them are now taken, it stops the netif transmission queue.
Such queue is worken up again only if an acknowedgment was received
from the firmware on one of our earlier-sent frames.
Meanwhile, upon channel close (#), the driver sends a CMD_STOP_CHIP
to the firmware, effectively closing all further communication. In
the high traffic case, the atomic counter remains at MAX_TX_URBS,
and all the URB contexts remain marked as active. While opening
the channel again (@), it cannot send any further frames since no
more free tx URB contexts are available.
Reset all tx URB contexts upon CAN channel close.
(*) 50 parallel instances of `cangen0 -g 0 -ix`
(#) `ifconfig can0 down`
(@) `ifconfig can0 up`
(%) "can: kvaser_usb: Don't free packets when tight on URBs"
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Flooding the Kvaser CAN to USB dongle with multiple reads and
writes in high frequency caused seemingly-random panics in the
kernel.
On further inspection, it seems the driver erroneously freed the
to-be-transmitted packet upon getting tight on URBs and returning
NETDEV_TX_BUSY, leading to invalid memory writes and double frees
at a later point in time.
Note:
Finding no more URBs/transmit-contexts and returning NETDEV_TX_BUSY
is a driver bug in and out of itself: it means that our start/stop
queue flow control is broken.
This patch only fixes the (buggy) error handling code; the root
cause shall be fixed in a later commit.
Acked-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
use of regmap_read() and regmap_write() in c_can_hw_raminit_syscon()
is not safe as the RAMINIT register can be shared between different drivers
at least for TI SoCs.
To make the modification atomic we switch to using regmap_update_bits().
regmap_update_bits() skips writing to the register if it's read content is the
same as what is going to be written. This causes an issue for us when we
need to clear the DONE bit with the initial condition START:0, DONE:1 as
DONE bit must be written with 1 to clear it.
So we defer the clearing of DONE bit to later when we set the START bit.
There we are sure that START bit is changed from 0 to 1 so the write of
1 to already set DONE bit will happen.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
During the CAN FD standardization process within the ISO it turned out that
the failure detection capability has to be improved.
The CAN in Automation organization (CiA) defined the already implemented CAN
FD controllers as 'non-ISO' and the upcoming improved CAN FD controllers as
'ISO' compliant. See at http://www.can-cia.com/index.php?id=1937
Finally there will be three types of CAN FD controllers in the future:
1. ISO compliant (fixed)
2. non-ISO compliant (fixed, like the M_CAN IP v3.0.1 in m_can.c)
3. ISO/non-ISO CAN FD controllers (switchable, like the PEAK USB FD)
So the current M_CAN driver for the M_CAN IP v3.0.1 has to expose its non-ISO
implementation by setting the CAN_CTRLMODE_FD_NON_ISO ctrlmode at startup.
As this bit cannot be switched at configuration time CAN_CTRLMODE_FD_NON_ISO
must not be set in ctrlmode_supported of the current M_CAN driver.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When changing flags in the CAN drivers ctrlmode the provided new content has to
be checked whether the bits are allowed to be changed. The bits that are to be
changed are given as a bitfield in cm->mask. Therefore checking against
cm->flags is wrong as the content can hold any kind of values.
The iproute2 tool sets the bits in cm->mask and cm->flags depending on the
detected command line options. To be robust against bogus user space
applications additionally sanitize the provided flags with the provided mask.
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Conflicts:
drivers/net/ethernet/amd/xgbe/xgbe-desc.c
drivers/net/ethernet/renesas/sh_eth.c
Overlapping changes in both conflict cases.
Signed-off-by: David S. Miller <davem@davemloft.net>
Replacing error state change handling with the new mechanism.
Signed-off-by: Andri Yngvason <andri.yngvason@marel.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Replacing error state change handling with the new mechanism.
Signed-off-by: Andri Yngvason <andri.yngvason@marel.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Replacing error state change handling with the new mechanism.
Signed-off-by: Andri Yngvason <andri.yngvason@marel.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The handling of can error states is different between platforms.
This is an attempt to correct that problem.
I've moved this handling into a generic function for changing the
error state. This ensures that error state changes are handled
the same way everywhere (where this function is used).
This new mechanism also adds reverse state transitioning in error
frames, i.e. the user will be notified through the socket interface
when the state goes down.
Signed-off-by: Andri Yngvason <andri.yngvason@marel.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fix various spelling errors in the comments of the CAN modules.
Signed-off-by: Jeremiah Mahler <jmmahler@gmail.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Several can modules in drivers/net/can use a banner[] variable at the
top which defines a string that is used once during init. This string
is also embedded with KERN_INFO which makes it printk() specific.
Improve the code by eliminating the banner[] variable and moving the
string to where it is printed. Then switch from printk(KERN_INFO to
pr_info() for the lines that were changed.
This patch is similar to [1] which was applied to net/can.
[1]: https://lkml.org/lkml/2014/11/22/10
Signed-off-by: Jeremiah Mahler <jmmahler@gmail.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes the endianess definition as well as the usage of the
multi-byte fields in the data structures exchanged with the PEAK-System USB
adapters.
By fixing the endianess, this patch also fixes the wrong usage of a 32-bits
local variable for handling the error status 16-bits field, in function
pcan_usb_pro_handle_error().
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch sets the correct reverse sequence order to the instructions
set to run, when any failure occurs during the initialization steps.
It also adds the missing unregistration call of the can device if the
failure appears after having been registered.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patchs fixes a misplaced call to memset() that fills the request
buffer with 0. The problem was with sending PCAN_USBPRO_REQ_FCT
requests, the content set by the caller was thus lost.
With this patch, the memory area is zeroed only when requesting info
from the device.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Conflicts:
drivers/net/ieee802154/fakehard.c
A bug fix went into 'net' for ieee802154/fakehard.c, which is removed
in 'net-next'.
Add build fix into the merge from Stephen Rothwell in openvswitch, the
logging macros take a new initial 'log' argument, a new call was added
in 'net' so when we merge that in here we have to explicitly add the
new 'log' arg to it else the build fails.
Signed-off-by: David S. Miller <davem@davemloft.net>
Bosch M_CAN is CAN FD capable device. This patch implements the CAN
FD features include up to 64 bytes payload and bitrate switch function.
1) Change the Rx FIFO and Tx Buffer to 64 bytes for support CAN FD
up to 64 bytes payload. It's backward compatible with old 8 bytes
normal CAN frame.
2) Allocate can frame or canfd frame based on EDL bit
3) Bitrate Switch function is disabled by default and will be enabled
according to CANFD_BRS bit in cf->flags.
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The spec mentions there may be a delay until the value written to INIT can be
read back due to the synchronization mechanism between the two clock domains.
But it does not indicate the exact clock cycles needed. The 5us delay is a
test value and seems ok.
Without the delay, CCCR.CCE bit may fail to be set and then the initialization
fail sometimes when do repeatly up and down.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The original code missed to set the cf->can_dlc in the RTR case, so add it.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The M_CAN message RAM is usually equipped with a parity or ECC functionality.
But RAM cells suffer a hardware reset and can therefore hold arbitrary content
at startup - including parity and/or ECC bits.
To prevent the M_CAN controller detecting checksum errors when reading
potentially uninitialized TX message RAM content to transmit CAN frames the TX
message RAM has to be written with (any kind of) initial data.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
m_can uses io memory which makes it not compilable on architectures
without HAS_IOMEM such as UML:
drivers/built-in.o: In function `m_can_plat_probe':
m_can.c:(.text+0x218cc5): undefined reference to `devm_ioremap_resource'
m_can.c:(.text+0x218df9): undefined reference to `devm_ioremap'
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The variable err was of the type u32. It was being compared with < 0, and being
an unsigned variable the comparison would have been always false.
Moreover, err was getting the return value from set_reset_mode() and
xcan_set_bittiming(), and both are returning int.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
these variable were only assigned some values, but then never
reused again.
so they are safe to be removed.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
It seems struct esd_usb2 dev is not deallocated on disconnect. The patch adds
the missing deallocation.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes a typo in CAN's dev.c:
CIA -> CiA
which stands for CAN in Automation.
Signed-off-by: Roman Fietze <roman.fietze@telemotive.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
AM4372 SoC has 2 DCAN modules. Add compatible id and
raminit driver data for it. The driver data is same as AM3352
but this gives us flexibility to add AM4372 specific quirks
if required later.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
AM3352 SoC has 2 DCAN modules. Add compatible id and
raminit driver data for am3352 DCAN.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
DRA7 SoC has 2 CAN IPs. Provide compatible IDs and RAMINIT
register data for both.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
DRA7 CAN IP suffers from a problem which causes it to be prevented
from fully turning OFF (i.e. stuck in transition) if the module was
disabled while there was traffic on the CAN_RX line.
To work around this issue we select the SLEEP pin state by default
on probe and use the DEFAULT pin state on CAN up and back to the
SLEEP pin state on CAN down.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some SoCs e.g. (TI DRA7xx) need a START pulse to start the
RAMINIT sequence i.e. START bit must be set and cleared before
checking for the DONE bit status.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some TI SoCs like DRA7 have a RAMINIT register specification
different from the other AMxx SoCs and as expected by the
existing driver.
To add more insanity, this register is shared with other
IPs like DSS, PCIe and PWM.
Provides a more generic mechanism to specify the RAMINIT
register location and START/DONE bit position and use the
syscon/regmap framework to access the register.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some platforms (e.g. TI) need special RAMINIT register handling.
Provide a way to store RAMINIT register description in driver data.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
We want to have more data than just can_dev_id to be present
in the driver data e.g. TI platforms need RAMINIT register
description. Introduce the c_can_driver_data structure and move
the can_dev_id into it.
Tidy up the way it is used on probe().
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
TI's RAMINIT DONE mechanism is buggy on AM43xx SoC and may not always
be set after the START bit is set. Although it seems to work fine even
in that case. So add a timeout mechanism to c_can_hw_raminit_wait_ti().
Don't bail out in that failure case but just print an error message.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
CAN_AT91 needs HAS_IOMEM, so depends on it. The related error (with
allmodconfig under um):
CC [M] drivers/net/can/at91_can.o
drivers/net/can/at91_can.c: In function ‘at91_can_probe’:
drivers/net/can/at91_can.c:1329:2: error: implicit declaration of function ‘ioremap_nocache’ [-Werror=implicit-function-declaration]
addr = ioremap_nocache(res->start, resource_size(res));
^
drivers/net/can/at91_can.c:1329:7: warning: assignment makes pointer from integer without a cast [enabled by default]
addr = ioremap_nocache(res->start, resource_size(res));
^
drivers/net/can/at91_can.c:1384:2: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
iounmap(addr);
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/mips/net/bpf_jit.c
drivers/net/can/flexcan.c
Both the flexcan and MIPS bpf_jit conflicts were cases of simple
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to make the driver work with the common clock framework, this patch
converts the clk_enable()/clk_disable() to
clk_prepare_enable()/clk_disable_unprepare(). While there, add the missing
error handling.
Signed-off-by: David Dueck <davidcdueck@googlemail.com>
Signed-off-by: Anthony Harivel <anthony.harivel@emtrion.de>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch increases the mask in the FLEXCAN_MCR_MAXMB() to 7 bits as in the
newer flexcan cores the MAXMB field is 7 bits wide.
Reported-by: David Jander <david@protonic.nl>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
After sending a RTR frame the TX mailbox becomes a RX_EMPTY mailbox. To avoid
side effects when the RX-FIFO is full, this patch puts the TX mailbox into
TX_INACTIVE mode in the transmission complete interrupt handler. This, of
course, leaves a race window between the actual completion of the transmission
and the handling of tx-complete interrupt. However this is the best we can do
without busy polling the tx complete interrupt.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch implements the workaround mentioned in ERR005829:
ERR005829: FlexCAN: FlexCAN does not transmit a message that is enabled to
be transmitted in a specific moment during the arbitration process.
Workaround: The workaround consists of two extra steps after setting up a
message for transmission:
Step 8: Reserve the first valid mailbox as an inactive mailbox (CODE=0b1000).
If RX FIFO is disabled, this mailbox must be message buffer 0. Otherwise, the
first valid mailbox can be found using the "RX FIFO filters" table in the
FlexCAN chapter of the chip reference manual.
Step 9: Write twice INACTIVE code (0b1000) into the first valid mailbox.
Signed-off-by: David Jander <david@protonic.nl>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Apparently mailboxes may contain random data at startup, causing some of them
being prepared for message reception. This causes overruns being missed or even
confusing the IRQ check for trasmitted messages, increasing the transmit
counter instead of the error counter.
This patch initializes all mailboxes after the FIFO as RX_INACTIVE.
Signed-off-by: David Jander <david@protonic.nl>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes the initialization of the TX mailbox. It is now correctly
initialized as TX_INACTIVE not RX_EMPTY.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add PCI ID definition for the single channel PCAN ExpressCard 34 adapter. Due
to the subsystem id evaluation the correct number of channels (here 1) is
created at initialization time. Tested including the LED functionality.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Pass the correct 'mask' and 'value' bits to c_can_hw_raminit_wait_ti(). They
seem to have been swapped in the usage instances.
Reported-by: Jay Schroeder <jay.schroeder@garmin.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Apparently can_restart() runs from a (timer-) interrupt and can call
flexcan_chip_[en|dis]able(), so avoid using usleep_range()
Signed-off-by: David Jander <david@protonic.nl>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Once the CAN-bus is open and a packet is sent, the controller switches
into the PASSIVE state. Once the BUS is closed again it goes the back
err-warning. The TX error counter goes 0 -> 0x80 -> 0x7f.
This patch makes sure that the user learns about this state chang
(CAN_STATE_ERROR_WARNING => CAN_STATE_ERROR_PASSIVE)
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Matthias Klein <matthias.klein@optimeas.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In case we don't have FLEXCAN_HAS_BROKEN_ERR_STATE and the user set
CAN_CTRLMODE_BERR_REPORTING once it can not be unset again until reboot.
So in case neither hardware nor user wants the error interrupt disable
the bit.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
devm_ioremap() returns NULL on error, not an ERR_PTR().
Fixes: 33cf756569 ('can: c_can_platform: Fix raminit, use devm_ioremap() instead of devm_ioremap_resource()')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When sja1000 is not compiled as module the SJA1000 chip is only
initialized during device registration on kernel boot. Should the chip
get a hardware reset there is no way to reinitialize it without re-
booting the Linux kernel.
This patch adds a check in sja1000_start if the chip is initialized, if
not we initialize it.
Signed-off-by: Mirza Krak <mirza.krak@hostmobility.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch moves the data allocated using dma_alloc_coherent to the
corresponding managed interface and does away with the calls to free the
allocated memory in the probe and remove functions.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
this patch removes best_rate variable from can_calc_bittiming()
function which was set but was never used.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add support of the device tree probing for the Renesas R-Car CAN controllers.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When writing the driver, I didn't give enough attention to the possible sources
of the CAN clock: although the value of the CLKR register was specified by the
platform data, the driver only handled one case, that is CAN clock being
sourced from the clkp1 clock, the same that clocks the whole CAN module. In
order to fix that overlook, we'll have to handle the CAN clock separately from
the peripheral clock (however, clkp1 will be specified for a CAN device only
once)...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The patch adds the basic CAN TX/RX function support for Bosch M_CAN controller.
For TX, only one dedicated tx buffer is used for sending data.
For RX, RXFIFO 0 is used for receiving data to avoid overflow.
Rx FIFO 1 and Rx Buffers are not used currently, as well as Tx Event FIFO.
Due to the message ram can be shared by multi m_can instances
and the fifo element is configurable which is SoC dependant,
the design is to parse the message ram related configuration data from device
tree rather than hardcode define it in driver which can make the message
ram sharing fully transparent to M_CAN controller driver,
then we can gain better driver maintainability and future features upgrade.
M_CAN also supports CANFD protocol features like data payload up to 64 bytes
and bitrate switch at runtime, however, this patch still does not add the
support for these features.
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
[mkl: Squahed semicolon cleanup by Fengguang Wu]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Extend FlexCAN driver to support Vybrid. Vybrids variant of the IP
has ECC support which is controlled through the memory error
control register (MECR). There is also an errata which leads to
false positive error detections (ID e5295). This patch disables
the memory error detection completely.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The funcion flexcan_get_berr_counter() may be called from userspace even if the
interface is down, this the clocks are disabled. This patch switches on the
clocks before accessing the ecr register.
Reported-by: Ashutosh Singh <ashuleapyear@gmail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
No need to manually copy debug settings into subdir Makefiles. kbuild
has a mechanism for inheriting, so let's use it.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The raminit register is shared register for both can0 and can1. Since commit:
32766ff net: can: Convert to use devm_ioremap_resource
devm_ioremap_resource() is used to map raminit register. When using both
interfaces the mapping for the can1 interface fails, leading to a non
functional can interface.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlPE2fYACgkQjTAFq1RaXHNpmwCfY+zM07sxULHpFYoLPEHVbdVh
tXgAoIG6RVra8G8aPEBEk1MeRMAx+HRj
=2is3
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-3.17-20140715' of git://gitorious.org/linux-can/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2014-07-15
this is a pull request of 4 patches for net-next/master.
Prabhakar Lad contributes a patch that converts the c_can driver to use
the devm api. The remaining four patches by Nikita Edward Baruzdin
improve the SJA1000 driver with loopback testing support and introduce
a new testing mode presume ack, for successful transmission even if no
ACK is received.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
SJA1000 has a self test mode (STM) which does not require
acknowledgement for the successful message transmission. In this mode a
node test is possible without any other active node on the bus.
This patch adds a possibility to set STM for SJA1000 controller through
specifying the corresponding CAN_CTRLMODE_PRESUME_ACK netlink flag.
Signed-off-by: Nikita Edward Baruzdin <nebaruzdin@gmail.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This adds support for hardware loopback in SJA1000 by utilising its self
reception request (SRR) feature. Upon SRR the message is transmitted and
received simultaneously, meaning you can't have hardware loopback
without actually sending a message to the CAN bus in case of SJA1000.
Signed-off-by: Nikita Edward Baruzdin <nebaruzdin@gmail.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch uses devm_* APIs as they are device managed and make code simpler.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The commit "slip: Fix deadlock in write_wakeup" fixes a deadlock caused
by a change made in both slcan and slip. This is a direct port of that
fix.
Signed-off-by: Tyler Hall <tylerwhall@gmail.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Andre Naujoks <nautsch2@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
