First, the siginfo preamble wasn't quite right; we need to indicate
that we are padding up to 4 ints of preamble for 64-bit code, and
then for compat mode we need to pad differently, using only 3 ints.
Second, the C ABI requires a save area of two registers, not two
pointers, since in compat mode we have 64-bit registers all of which
we need to save, even though we only have 32-bit VAs.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
We were using the same 5-sec minsec for the clocksource and sched_clock
that we were using for the clock_event_device. For the clock_event_device
that's exactly right since it has a short maximum countdown time.
But for sched_clock we want to avoid wraparound when converting from
ticks to nsec over a much longer window, so we force a shift of 10.
And for clocksource it seems dodgy to use a 5-sec minsec as well, so we
copy some other platforms and force a shift of 22.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This commit is primarily changes caused by reviewing "sparse"
and "checkpatch" output on our sources, so is somewhat noisy, since
things like "printk() -> pr_err()" (or whatever) throughout the
codebase tend to get tedious to read. Rather than trying to tease
apart precisely which things changed due to which type of code
review, this commit includes various cleanups in the code:
- sparse: Add declarations in headers for globals.
- sparse: Fix __user annotations.
- sparse: Using gfp_t consistently instead of int.
- sparse: removing functions not actually used.
- checkpatch: Clean up printk() warnings by using pr_info(), etc.;
also avoid partial-line printks except in bootup code.
- checkpatch: Use exposed structs rather than typedefs.
- checkpatch: Change some C99 comments to C89 comments.
In addition, a couple of minor other changes are rolled in
to this commit:
- Add support for a "raise" instruction to cause SIGFPE, etc., to be raised.
- Remove some compat code that is unnecessary when we fully eliminate
some of the deprecated syscalls from the generic syscall ABI.
- Update the tile_defconfig to reflect current config contents.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The C file (tile-desc_{32,64}.c) was about 300KB before this change,
and is now shrunk down to 100K. The original file included support
for BFD in the binutils toolchain, which is not necessary in the
kernel; the kernel version only needs to include enough support to
enable the single-stepper and backtracer.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
This network (the "UDN") connects all the cpus on the chip in a
wormhole-routed dynamic network. Subrectangles of the chip can
be allocated by a "create" ioctl on /dev/hardwall, and then to access the
UDN in that rectangle, tasks must perform an "activate" ioctl on that
same file object after affinitizing themselves to a single cpu in
the region. Sending a wormhole-routed message that tries to leave
that subrectangle causes all activated tasks to receive a SIGILL
(just as they would if they tried to access the UDN without first
activating themselves to a hardwall rectangle).
The original submission of this code to LKML had the driver
instantiated under /proc/tile/hardwall. Now we just use a character
device for this, conventionally /dev/hardwall. Some futures planning
for the TILE-Gx chip suggests that we may want to have other types of
devices that share the general model of "bind a task to a cpu, then
'activate' a file descriptor on a pseudo-device that gives access to
some hardware resource". As such, we are using a device rather
than, for example, a syscall, to set up and activate this code.
As part of this change, the compat_ptr() declaration was fixed and used
to pass the compat_ioctl argument to the normal ioctl. So far we limit
compat code to 2GB, so the difference between zero-extend and sign-extend
(the latter being correct, eventually) had been overlooked.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
This model is based on the on-chip interrupt model used by the
TILE-Gx next-generation hardware, and interacts much more cleanly
with the Linux generic IRQ layer.
The change includes modifications to the Tilera hypervisor, which
are reflected in the hypervisor headers in arch/tile/include/arch/.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
It turns out there is some variance on the calling conventions for
these syscalls, and <asm-generic/syscalls.h> is already the mechanism
used to handle this. Switch arch/tile over to using that mechanism and
tweak the calling conventions for a couple of tile syscalls to match
<asm-generic/syscalls.h>.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This change is the core kernel support for TILEPro and TILE64 chips.
No driver support (except the console driver) is included yet.
This includes the relevant Linux headers in asm/; the low-level
low-level "Tile architecture" headers in arch/, which are
shared with the hypervisor, etc., and are build-system agnostic;
and the relevant hypervisor headers in hv/.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Reviewed-by: Paul Mundt <lethal@linux-sh.org>
