The 100c08 scratch page is mapped using dma_map_page() before the TTM
layer has had a chance to set the DMA mask. This means we are still
running with the default of 32 when this code executes, and this causes
problems for platforms with no memory below 4 GB (such as AMD Seattle)
So move the dma_map_page() to the .oneinit hook, which executes after the
DMA mask has been set.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The 100c10 scratch page is mapped using dma_map_page() before the TTM
layer has had a chance to set the DMA mask. This means we are still
running with the default of 32 when this code executes, and this causes
problems for platforms with no memory below 4 GB (such as AMD Seattle)
So move the dma_map_page() to the .oneinit hook, which executes after the
DMA mask has been set.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Doing direct 64 bit divisions in kernel code leads to references to
undefined symbols on 32 bit architectures. Replace such divisions with
calls to div64_s64 to make the module usable on 32 bit archs.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Karol Herbst <karolherbst@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This enables memory reclocking on Maxwell. Sadly without a PMU firmware it
is useless for gm20x gpus.
Signed-off-by: Karol Herbst <karolherbst@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
I'm quite sure that those coefficients are real close, because while
testing the biggest error compared to nvidia was around -1.5% (biggest
error with right coefficients is 12.5mV / 600mV = 2%).
These coefficients were REed by modifing the voltage map entries and by
calculating the set voltage back until I was able to forecast which voltage
nvidia sets for a given voltage map entry.
With these formulars I am able to precisely predict at which exact
temperature Nvidia down- or upvolts due to a changed therm reading.
That's why I am quite sure these are right, or at least really really
close.
v4: Use better coefficients and speedo.
v5: Add error message when speedo is missing.
Signed-off-by: Karol Herbst <karolherbst@gmail.com>
Reviewed-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
v5: Squashed speedo related commits.
Signed-off-by: Karol Herbst <karolherbst@gmail.com>
Reviewed-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Since gf100 we need a speedo value for calculating the voltage. The readout
will be added in a later patch.
Signed-off-by: Karol Herbst <karolherbst@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Depending on the value a different formular is used to calculated the
voltage for this entry.
Signed-off-by: Karol Herbst <karolherbst@gmail.com>
Reviewed-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
If we calculate the voltage in the table right, we get all kinds of values,
which never fit the hardware steps, so we use the closest higher value the
hardware can do.
v3: Simplify the implementation.
v5: Initialize best_err with volt->max_uv.
Signed-off-by: Karol Herbst <karolherbst@gmail.com>
Reviewed-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
0: base clock from the vbios is max clock (default)
1: boost only to boost clock from the vbios
2: boost to max clock available
v2: Moved into nvkm_cstate_valid.
v4: Check the existence of the clocks before limiting.
v5: Default to boost level 0.
Signed-off-by: Karol Herbst <karolherbst@gmail.com>
Reviewed-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This table contains three important clocks:
base clock: This is the non boosted max clock.
tdp clock: The clock at wich the vbios guarentees the TDP won't ever be
exceeded at max load (seems to be always the same as the base
clock, but behaves differently).
boost clock: The avg clock the gpu will stay boosted to. It doesn't seem to
affect the behaviour of the nvidia driver at all though.
v2: Make clear that base/boost/tdp fields are ids.
v5: Rename Base clock to vpstate.
Make vbios pointers 32bit.
Signed-off-by: Karol Herbst <karolherbst@gmail.com>
Reviewed-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We should never allow to select a cstate which current voltage (depending
on the temperature) is higher than
1. the max volt entries in the voltage map table.
2. what tha gpu actually can volt to.
v3: Use find_best for all cstates before actually trying.
Add nvkm_cstate_get function to get cstate by index.
v5: Cstates with voltages lower then min_uv are valid.
Move nvkm_cstate_get into the previous commit.
Signed-off-by: Karol Herbst <karolherbst@gmail.com>
Reviewed-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Now the cstatei parameter can be used of the nvkm_cstate_prog function to
select a specific cstate.
v5: Make a constant for the magic value.
Use list_last_entry.
Add nvkm_cstate_get here instead of in the next commit.
Signed-off-by: Karol Herbst <karolherbst@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The voltage entries actually may map to a different voltage depending on
the current temperature.
v2: Only read the temperature when actually needed.
v5: Be smarter about using max().
Don't read the temperature anymore.
Signed-off-by: Karol Herbst <karolherbst@gmail.com>
Reviewed-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This way other subdevs can notify the clk subdev about temperature changes
without the need of clk to poll that value.
Also make this function safe to be called from an interrupt handler.
Signed-off-by: Karol Herbst <karolherbst@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
It is better to read out the id out of the cstate struct directly instead
of iterating over the list of cstates over and over again. Especially when
we start saving pointers to a nvkm_cstate struct, it makes things easier.
v5: Rename field to id.
Signed-off-by: Karol Herbst <karolherbst@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Each pstate has its own voltage map entry like each cstate has.
The voltages of those entries act as a floor value for the currently
selected pstate and nvidia never sets a voltage below them.
Signed-off-by: Karol Herbst <karolherbst@gmail.com>
Reviewed-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
There are at least three "max" entries, which specify the max voltage.
Because they are actually normal voltage map entries, they can also be
affected by the temperature.
Nvidia respects those entries and if they get changed, nvidia uses the
lower voltage from all three.
We shouldn't exceed those voltages at any given time.
v2: State what those entries do in the source.
v3: Add the third max entry.
v5: Better describe the entries.
Signed-off-by: Karol Herbst <karolherbst@gmail.com>
Reviewed-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
nvkm_volt_map_min is a copy of nvkm_volt_map, which always returns the
lowest possible voltage for a cstate.
nvkm_volt_map will get a temperature parameter there later and also fix
the voltage calculation, so that this functions will be completly
different later.
Signed-off-by: Karol Herbst <karolherbst@gmail.com>
Reviewed-by: Martin Peres <martin.peres@free.fr>
Tested-by: Pierre Moreau <pierre.morrow@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
There is a field in the voltage table which tells us if the VIDs are taken
from the entries or calculated through the header.
v2: Don't break older versions.
v5: Reverse flag name.
Signed-off-by: Karol Herbst <karolherbst@gmail.com>
Reviewed-by: Martin Peres <martin.peres@free.fr>
Tested-by: Pierre Moreau <pierre.morrow@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Some Fermi+ GPUs specify VID information via voltage table entries, rather
than describing them as a range in the header.
The mask may be bigger than 0x1fffff, but this value is already >2V, so it
will be fine for now.
This patch fixes volting issues on those cards enabling them to switch
cstates.
v6: rework message
Signed-off-by: Karol Herbst <karolherbst@gmail.com>
Reviewed-by: Martin Peres <martin.peres@free.fr>
Tested-by: Pierre Moreau <pierre.morrow@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Previously we parsed that table a bit wrong:
1. The entry layout depends on the sensor type used.
2. We have all resitors in one entry for the INA3221.
3. The config is already included in the vbios.
This commit addresses that issue and with that we should be able to read
out the right power consumption for every GPU with a INA209, INA219 and
INA3221.
Signed-off-by: Karol Herbst <karolherbst@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This can show up on SPARC or other architectures that don't handle
unaligned accesses. The kernel normally fixes these up, but it shouldn't
have to.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96836
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
gk20a_ibus_init_ibus_ring() can be called from gk20a_ibus_intr(), in
non-interruptible context. Replace use of usleep_range() with udelay().
Reported-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The dma-mapping core and the implementations do not change the DMA
attributes passed by pointer. Thus the pointer can point to const data.
However the attributes do not have to be a bitfield. Instead unsigned
long will do fine:
1. This is just simpler. Both in terms of reading the code and setting
attributes. Instead of initializing local attributes on the stack
and passing pointer to it to dma_set_attr(), just set the bits.
2. It brings safeness and checking for const correctness because the
attributes are passed by value.
Semantic patches for this change (at least most of them):
virtual patch
virtual context
@r@
identifier f, attrs;
@@
f(...,
- struct dma_attrs *attrs
+ unsigned long attrs
, ...)
{
...
}
@@
identifier r.f;
@@
f(...,
- NULL
+ 0
)
and
// Options: --all-includes
virtual patch
virtual context
@r@
identifier f, attrs;
type t;
@@
t f(..., struct dma_attrs *attrs);
@@
identifier r.f;
@@
f(...,
- NULL
+ 0
)
Link: http://lkml.kernel.org/r/1468399300-5399-2-git-send-email-k.kozlowski@samsung.com
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Acked-by: Mark Salter <msalter@redhat.com> [c6x]
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com> [cris]
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> [drm]
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Fabien Dessenne <fabien.dessenne@st.com> [bdisp]
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com> [vb2-core]
Acked-by: David Vrabel <david.vrabel@citrix.com> [xen]
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> [xen swiotlb]
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Richard Kuo <rkuo@codeaurora.org> [hexagon]
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Acked-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> [s390]
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no> [avr32]
Acked-by: Vineet Gupta <vgupta@synopsys.com> [arc]
Acked-by: Robin Murphy <robin.murphy@arm.com> [arm64 and dma-iommu]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Due to the GPU preventing us from touching NV_PLTCG_LTCS_LTSS_CBC_BASE,
we cannot provide CBC/ZBC support without signed PMU firmware to handle
the task for us...
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
GFxxx/GM1xx support the selection of 64/128KiB big pages globally.
GM2xx supports the same, as well as another mode where the page size
can be selected per-instance.
We default to 128KiB pages (With per-instance for GM200, but the current
code selects 128KiB there already) as the MMU code isn't currently able
to handle otherwise.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Makes common the code that was previously used by the PMU table parsing,
as it appears other tables need this too.
Not much of an idea what this is all about...
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Corresponds with GT215. Don't rely on the lock test logic being
unconditionally enabled, and disable test logic when done (presumably
to save power).
v2: Remove warning, nvkm_msec already warns on time-out
Signed-off-by: Roy Spliet <nouveau@spliet.org>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Defer the loading of firmware files to the chip-specific part of secure
boot. This allows implementations to retry loading firmware if the first
attempt failed ; for the GM200 implementation, this happens when trying
to reset a falcon, typically in reaction to GR init.
Firmware loading may fail for a variety of reasons, such as the
filesystem where they reside not being ready at init time. This new
behavior allows GR to be initialized the next time we try to use it if
the firmware has become available.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Make it possible to call gm20x_secboot_prepare_blobs() several times
after either success or failure without re-building already existing
blobs. The function will now try to load firmware files that have
previously failed before returning success.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Some members were documented in the wrong structure.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We shouldn't set voltages below the min or above the max voltage the gpu is
able to set, so save the range for future lookups.
Signed-off-by: Karol Herbst <karolherbst@gmail.de>
Reviewed-by: Martin Peres <martin.peres@free.fr>
Tested-by: Pierre Moreau <pierre.morrow@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This patch adds support for advanced features supported by the
Noise-Aware PLL of Maxwell. Glitchless switch allows the PL field to be
updated without disabling the PLL first if the SYNC_MODE bit of the CFG
register is set.
More significantly, DFS allows the PLL to monitor the actual input
voltage and to dynamically lower the output frequency accordingly. This
allows the clock to be more tolerant of lower voltages.
These improvements are only supported for Tegra speedos >= 1.
Also add the voltage table that is suitable for GM20B's NAPLL. This
change needs to be done atomically for the right voltages to be used by
the clock driver.
v2. Fix build on non-Tegra platforms
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Strip the _ prefix off the gk20a clock constructor.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
