Along with z/VM NICs, there's additional device types that only support
a specific transport mode (eg. external-bridged IQD).
Identify the corresponding error code, and raise a fitting error message
so that the user knows to adjust their device configuration.
On top of that also fix the subsequent error path, so that the rejected
cmd doesn't need to wait for a timeout but gets cancelled straight away.
Fixes: 4a71df5004 ("qeth: new qeth device driver")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti says:
====================
net/sched: cls_u32: fix refcount leak
a refcount leak in the error path of u32_change() has been recently
introduced. It can be observed with the following commands:
[root@f31 ~]# tc filter replace dev eth0 ingress protocol ip prio 97 \
> u32 match ip src 127.0.0.1/32 indev notexist20 flowid 1:1 action drop
RTNETLINK answers: Invalid argument
We have an error talking to the kernel
[root@f31 ~]# tc filter replace dev eth0 ingress protocol ip prio 98 \
> handle 42:42 u32 divisor 256
Error: cls_u32: Divisor can only be used on a hash table.
We have an error talking to the kernel
[root@f31 ~]# tc filter replace dev eth0 ingress protocol ip prio 99 \
> u32 ht 47:47
Error: cls_u32: Specified hash table not found.
We have an error talking to the kernel
they all legitimately return -EINVAL; however, they leave semi-configured
filters at eth0 tc ingress:
[root@f31 ~]# tc filter show dev eth0 ingress
filter protocol ip pref 97 u32 chain 0
filter protocol ip pref 97 u32 chain 0 fh 800: ht divisor 1
filter protocol ip pref 98 u32 chain 0
filter protocol ip pref 98 u32 chain 0 fh 801: ht divisor 1
filter protocol ip pref 99 u32 chain 0
filter protocol ip pref 99 u32 chain 0 fh 802: ht divisor 1
With older kernels, filters were unconditionally considered empty (and
thus de-refcounted) on the error path of ->change().
After commit 8b64678e0a ("net: sched: refactor tp insert/delete for
concurrent execution"), filters were considered empty when the walk()
function didn't set 'walker.stop' to 1.
Finally, with commit 6676d5e416 ("net: sched: set dedicated tcf_walker
flag when tp is empty"), tc filters are considered empty unless the walker
function is called with a non-NULL handle. This last change doesn't fit
cls_u32 design, because at least the "root hnode" is (almost) always
non-NULL, as it's allocated in u32_init().
- patch 1/2 is a proposal to restore the original kernel behavior, where
no filter was installed in the error path of u32_change().
- patch 2/2 adds tdc selftests that can be ued to verify the correct
behavior of u32 in the error path of ->change().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
- move test "e9a3 - Add u32 with source match" to u32.json, and change the
match pattern to catch all hnodes
- add testcases for relevant error paths of cls_u32 module
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when users replace cls_u32 filters with new ones having wrong parameters,
so that u32_change() fails to validate them, the kernel doesn't roll-back
correctly, and leaves semi-configured rules.
Fix this in u32_walk(), avoiding a call to the walker function on filters
that don't have a match rule connected. The side effect is, these "empty"
filters are not even dumped when present; but that shouldn't be a problem
as long as we are restoring the original behaviour, where semi-configured
filters were not even added in the error path of u32_change().
Fixes: 6676d5e416 ("net: sched: set dedicated tcf_walker flag when tp is empty")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In s3fwrn5_fw_recv_frame, if fw_info->rsp is not empty, the
current code causes a crash via BUG_ON. However, s3fwrn5_fw_send_msg
does not crash in such a scenario. The patch replaces the BUG_ON
by returning the error to the callers and frees up skb.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart says:
====================
net: macb: fix probing of PHY not described in the dt
The macb Ethernet driver supports various ways of referencing its
network PHY. When a device tree is used the PHY can be referenced with
a phy-handle or, if connected to its internal MDIO bus, described in
a child node. Some platforms omitted the PHY description while
connecting the PHY to the internal MDIO bus and in such cases the MDIO
bus has to be scanned "manually" by the macb driver.
Prior to the phylink conversion the driver registered the MDIO bus with
of_mdiobus_register and then in case the PHY couldn't be retrieved
using dt or using phy_find_first (because registering an MDIO bus with
of_mdiobus_register masks all PHYs) the macb driver was "manually"
scanning the MDIO bus (like mdiobus_register does). The phylink
conversion did break this particular case but reimplementing the manual
scan of the bus in the macb driver wouldn't be very clean. The solution
seems to be registering the MDIO bus based on if the PHYs are described
in the device tree or not.
There are multiple ways to do this, none is perfect. I chose to check if
any of the child nodes of the macb node was a network PHY and based on
this to register the MDIO bus with the of_ helper or not. The drawback
is boards referencing the PHY through phy-handle, would scan the entire
MDIO bus of the macb at boot time (as the MDIO bus would be registered
with mdiobus_register). For this solution to work properly
of_mdiobus_child_is_phy has to be exported, which means the patch doing
so has to be backported to -stable as well.
Another possible solution could have been to simply check if the macb
node has a child node by counting its sub-nodes. This isn't techically
perfect, as there could be other sub-nodes (in practice this should be
fine, fixed-link being taken care of in the driver). We could also
simply s/of_mdiobus_register/mdiobus_register/ but that could break
boards using the PHY description in child node as a selector (which
really would be not a proper way to do this...).
The real issue here being having PHYs not described in the dt but we
have dt backward compatibility, so we have to live with that.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the case where the PHY isn't described in the device
tree. This is due to the way the MDIO bus is registered in the driver:
whether the PHY is described in the device tree or not, the bus is
registered through of_mdiobus_register. The function masks all the PHYs
and only allow probing the ones described in the device tree. Prior to
the Phylink conversion this was also done but later on in the driver
the MDIO bus was manually scanned to circumvent the fact that the PHY
wasn't described.
This patch fixes it in a proper way, by registering the MDIO bus based
on if the PHY attached to a given interface is described in the device
tree or not.
Fixes: 7897b071ac ("net: macb: convert to phylink")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch exports of_mdiobus_child_is_phy, allowing to check if a child
node is a network PHY.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2019-12-19
The following pull-request contains BPF updates for your *net* tree.
We've added 10 non-merge commits during the last 8 day(s) which contain
a total of 21 files changed, 269 insertions(+), 108 deletions(-).
The main changes are:
1) Fix lack of synchronization between xsk wakeup and destroying resources
used by xsk wakeup, from Maxim Mikityanskiy.
2) Fix pruning with tail call patching, untrack programs in case of verifier
error and fix a cgroup local storage tracking bug, from Daniel Borkmann.
3) Fix clearing skb->tstamp in bpf_redirect() when going from ingress to
egress which otherwise cause issues e.g. on fq qdisc, from Lorenz Bauer.
4) Fix compile warning of unused proc_dointvec_minmax_bpf_restricted() when
only cBPF is present, from Alexander Lobakin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Expand dummy prog generation such that we can easily check on return
codes and add few more test cases to make sure we keep on tracking
pruning behavior.
# ./test_verifier
[...]
#1066/p XDP pkt read, pkt_data <= pkt_meta', bad access 1 OK
#1067/p XDP pkt read, pkt_data <= pkt_meta', bad access 2 OK
Summary: 1580 PASSED, 0 SKIPPED, 0 FAILED
Also verified that JIT dump of added test cases looks good.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/df7200b6021444fd369376d227de917357285b65.1576789878.git.daniel@iogearbox.net
While testing Cilium with /unreleased/ Linus' tree under BPF-based NodePort
implementation, I noticed a strange BPF SNAT engine behavior from time to
time. In some cases it would do the correct SNAT/DNAT service translation,
but at a random point in time it would just stop and perform an unexpected
translation after SYN, SYN/ACK and stack would send a RST back. While initially
assuming that there is some sort of a race condition in BPF code, adding
trace_printk()s for debugging purposes at some point seemed to have resolved
the issue auto-magically.
Digging deeper on this Heisenbug and reducing the trace_printk() calls to
an absolute minimum, it turns out that a single call would suffice to
trigger / not trigger the seen RST issue, even though the logic of the
program itself remains unchanged. Turns out the single call changed verifier
pruning behavior to get everything to work. Reconstructing a minimal test
case, the incorrect JIT dump looked as follows:
# bpftool p d j i 11346
0xffffffffc0cba96c:
[...]
21: movzbq 0x30(%rdi),%rax
26: cmp $0xd,%rax
2a: je 0x000000000000003a
2c: xor %edx,%edx
2e: movabs $0xffff89cc74e85800,%rsi
38: jmp 0x0000000000000049
3a: mov $0x2,%edx
3f: movabs $0xffff89cc74e85800,%rsi
49: mov -0x224(%rbp),%eax
4f: cmp $0x20,%eax
52: ja 0x0000000000000062
54: add $0x1,%eax
57: mov %eax,-0x224(%rbp)
5d: jmpq 0xffffffffffff6911
62: mov $0x1,%eax
[...]
Hence, unexpectedly, JIT emitted a direct jump even though retpoline based
one would have been needed since in line 2c and 3a we have different slot
keys in BPF reg r3. Verifier log of the test case reveals what happened:
0: (b7) r0 = 14
1: (73) *(u8 *)(r1 +48) = r0
2: (71) r0 = *(u8 *)(r1 +48)
3: (15) if r0 == 0xd goto pc+4
R0_w=inv(id=0,umax_value=255,var_off=(0x0; 0xff)) R1=ctx(id=0,off=0,imm=0) R10=fp0
4: (b7) r3 = 0
5: (18) r2 = 0xffff89cc74d54a00
7: (05) goto pc+3
11: (85) call bpf_tail_call#12
12: (b7) r0 = 1
13: (95) exit
from 3 to 8: R0_w=inv13 R1=ctx(id=0,off=0,imm=0) R10=fp0
8: (b7) r3 = 2
9: (18) r2 = 0xffff89cc74d54a00
11: safe
processed 13 insns (limit 1000000) [...]
Second branch is pruned by verifier since considered safe, but issue is that
record_func_key() couldn't have seen the index in line 3a and therefore
decided that emitting a direct jump at this location was okay.
Fix this by reusing our backtracking logic for precise scalar verification
in order to prevent pruning on the slot key. This means verifier will track
content of r3 all the way backwards and only prune if both scalars were
unknown in state equivalence check and therefore poisoned in the first place
in record_func_key(). The range is [x,x] in record_func_key() case since
the slot always would have to be constant immediate. Correct verification
after fix:
0: (b7) r0 = 14
1: (73) *(u8 *)(r1 +48) = r0
2: (71) r0 = *(u8 *)(r1 +48)
3: (15) if r0 == 0xd goto pc+4
R0_w=invP(id=0,umax_value=255,var_off=(0x0; 0xff)) R1=ctx(id=0,off=0,imm=0) R10=fp0
4: (b7) r3 = 0
5: (18) r2 = 0x0
7: (05) goto pc+3
11: (85) call bpf_tail_call#12
12: (b7) r0 = 1
13: (95) exit
from 3 to 8: R0_w=invP13 R1=ctx(id=0,off=0,imm=0) R10=fp0
8: (b7) r3 = 2
9: (18) r2 = 0x0
11: (85) call bpf_tail_call#12
12: (b7) r0 = 1
13: (95) exit
processed 15 insns (limit 1000000) [...]
And correct corresponding JIT dump:
# bpftool p d j i 11
0xffffffffc0dc34c4:
[...]
21: movzbq 0x30(%rdi),%rax
26: cmp $0xd,%rax
2a: je 0x000000000000003a
2c: xor %edx,%edx
2e: movabs $0xffff9928b4c02200,%rsi
38: jmp 0x0000000000000049
3a: mov $0x2,%edx
3f: movabs $0xffff9928b4c02200,%rsi
49: cmp $0x4,%rdx
4d: jae 0x0000000000000093
4f: and $0x3,%edx
52: mov %edx,%edx
54: cmp %edx,0x24(%rsi)
57: jbe 0x0000000000000093
59: mov -0x224(%rbp),%eax
5f: cmp $0x20,%eax
62: ja 0x0000000000000093
64: add $0x1,%eax
67: mov %eax,-0x224(%rbp)
6d: mov 0x110(%rsi,%rdx,8),%rax
75: test %rax,%rax
78: je 0x0000000000000093
7a: mov 0x30(%rax),%rax
7e: add $0x19,%rax
82: callq 0x000000000000008e
87: pause
89: lfence
8c: jmp 0x0000000000000087
8e: mov %rax,(%rsp)
92: retq
93: mov $0x1,%eax
[...]
Also explicitly adding explicit env->allow_ptr_leaks to fixup_bpf_calls() since
backtracking is enabled under former (direct jumps as well, but use different
test). In case of only tracking different map pointers as in c93552c443 ("bpf:
properly enforce index mask to prevent out-of-bounds speculation"), pruning
cannot make such short-cuts, neither if there are paths with scalar and non-scalar
types as r3. mark_chain_precision() is only needed after we know that
register_is_const(). If it was not the case, we already poison the key on first
path and non-const key in later paths are not matching the scalar range in regsafe()
either. Cilium NodePort testing passes fine as well now. Note, released kernels
not affected.
Fixes: d2e4c1e6c2 ("bpf: Constant map key tracking for prog array pokes")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/ac43ffdeb7386c5bd688761ed266f3722bb39823.1576789878.git.daniel@iogearbox.net
proc_dointvec_minmax_bpf_restricted() has been firstly introduced
in commit 2e4a30983b ("bpf: restrict access to core bpf sysctls")
under CONFIG_HAVE_EBPF_JIT. Then, this ifdef has been removed in
ede95a63b5 ("bpf: add bpf_jit_limit knob to restrict unpriv
allocations"), because a new sysctl, bpf_jit_limit, made use of it.
Finally, this parameter has become long instead of integer with
fdadd04931 ("bpf: fix bpf_jit_limit knob for PAGE_SIZE >= 64K")
and thus, a new proc_dolongvec_minmax_bpf_restricted() has been
added.
With this last change, we got back to that
proc_dointvec_minmax_bpf_restricted() is used only under
CONFIG_HAVE_EBPF_JIT, but the corresponding ifdef has not been
brought back.
So, in configurations like CONFIG_BPF_JIT=y && CONFIG_HAVE_EBPF_JIT=n
since v4.20 we have:
CC net/core/sysctl_net_core.o
net/core/sysctl_net_core.c:292:1: warning: ‘proc_dointvec_minmax_bpf_restricted’ defined but not used [-Wunused-function]
292 | proc_dointvec_minmax_bpf_restricted(struct ctl_table *table, int write,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Suppress this by guarding it with CONFIG_HAVE_EBPF_JIT again.
Fixes: fdadd04931 ("bpf: fix bpf_jit_limit knob for PAGE_SIZE >= 64K")
Signed-off-by: Alexander Lobakin <alobakin@dlink.ru>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191218091821.7080-1-alobakin@dlink.ru
Maxim Mikityanskiy says:
====================
This series addresses the issue described in the commit message of the
first patch: lack of synchronization between XSK wakeup and destroying
the resources used by XSK wakeup. The idea is similar to napi_synchronize.
The series contains fixes for the drivers that implement XSK.
v2 incorporates changes suggested by Björn:
1. Call synchronize_rcu in Intel drivers only if the XDP program is
being unloaded.
2. Don't forget rcu_read_lock when wakeup is called from xsk_poll.
3. Use xs->zc as the condition to call ndo_xsk_wakeup.
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Use synchronize_rcu to wait until the XSK wakeup function finishes
before destroying the resources it uses:
1. ixgbe_down already calls synchronize_rcu after setting __IXGBE_DOWN.
2. After switching the XDP program, call synchronize_rcu to let
ixgbe_xsk_wakeup exit before the XDP program is freed.
3. Changing the number of channels brings the interface down.
4. Disabling UMEM sets __IXGBE_TX_DISABLED before closing hardware
resources and resetting xsk_umem. Check that bit in ixgbe_xsk_wakeup to
avoid using the XDP ring when it's already destroyed. synchronize_rcu is
called from ixgbe_txrx_ring_disable.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191217162023.16011-5-maximmi@mellanox.com
Use synchronize_rcu to wait until the XSK wakeup function finishes
before destroying the resources it uses:
1. i40e_down already calls synchronize_rcu. On i40e_down either
__I40E_VSI_DOWN or __I40E_CONFIG_BUSY is set. Check the latter in
i40e_xsk_wakeup (the former is already checked there).
2. After switching the XDP program, call synchronize_rcu to let
i40e_xsk_wakeup exit before the XDP program is freed.
3. Changing the number of channels brings the interface down (see
i40e_prep_for_reset and i40e_pf_quiesce_all_vsi).
4. Disabling UMEM sets __I40E_CONFIG_BUSY, too.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191217162023.16011-4-maximmi@mellanox.com
After disabling resources necessary for XSK (the XDP program, channels,
XSK queues), use synchronize_rcu to wait until the XSK wakeup function
finishes, before freeing the resources.
Suspend XSK wakeups during switching channels. If the XDP program is
being removed, synchronize_rcu before closing the old channels to allow
XSK wakeup to complete.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191217162023.16011-3-maximmi@mellanox.com
The XSK wakeup callback in drivers makes some sanity checks before
triggering NAPI. However, some configuration changes may occur during
this function that affect the result of those checks. For example, the
interface can go down, and all the resources will be destroyed after the
checks in the wakeup function, but before it attempts to use these
resources. Wrap this callback in rcu_read_lock to allow driver to
synchronize_rcu before actually destroying the resources.
xsk_wakeup is a new function that encapsulates calling ndo_xsk_wakeup
wrapped into the RCU lock. After this commit, xsk_poll starts using
xsk_wakeup and checks xs->zc instead of ndo_xsk_wakeup != NULL to decide
ndo_xsk_wakeup should be called. It also fixes a bug introduced with the
need_wakeup feature: a non-zero-copy socket may be used with a driver
supporting zero-copy, and in this case ndo_xsk_wakeup should not be
called, so the xs->zc check is the correct one.
Fixes: 77cd0d7b3f ("xsk: add support for need_wakeup flag in AF_XDP rings")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191217162023.16011-2-maximmi@mellanox.com
Jose Abreu says:
====================
net: stmmac: Fixes for -net
Fixes for stmmac.
1) Fixes the filtering selftests (again) for cases when the number of multicast
filters are not enough.
2) Fixes SPH feature for MTU > default.
3) Fixes the behavior of accepting invalid MTU values.
4) Fixes FCS stripping for multi-descriptor packets.
5) Fixes the change of RX buffer size in XGMAC.
6) Fixes RX buffer size alignment.
7) Fixes the 16KB buffer alignment.
8) Fixes the enabling of 16KB buffer size feature.
9) Always arm the TX coalesce timer so that missed interrupts do not cause
a TX queue timeout.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If TX Coalesce timer is enabled we should always arm it, otherwise we
may hit the case where an interrupt is missed and the TX Queue will
timeout.
Arming the timer does not necessarly mean it will run the tx_clean()
because this function is wrapped around NAPI launcher.
Fixes: 9125cdd1be ("stmmac: add the initial tx coalesce schema")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XGMAC supports maximum MTU that can go to 16KB. Lets add this check in
the calculation of RX buffer size.
Fixes: 7ac6653a08 ("stmmac: Move the STMicroelectronics driver")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 16KB RX Buffer must also be 16 byte aligned. Fix it.
Fixes: 7ac6653a08 ("stmmac: Move the STMicroelectronics driver")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to align the RX buffer size to at least 16 byte so that IP
doesn't mis-behave. This is required by HW.
Changes from v2:
- Align UP and not DOWN (David)
Fixes: 7ac6653a08 ("stmmac: Move the STMicroelectronics driver")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When switching between buffer sizes we need to clear the previous value.
Fixes: d6ddfacd95 ("net: stmmac: Add DMA related callbacks for XGMAC2")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the last received buffer contains the FCS field. Check for end of
packet before trying to strip the FCS field.
Fixes: 88ebe2cf7f ("net: stmmac: Rework stmmac_rx()")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The maximum MTU value is determined by the maximum size of TX FIFO so
that a full packet can fit in the FIFO. Add a check for this in the MTU
change callback.
Also check if provided and rounded MTU does not passes the maximum limit
of 16K.
Changes from v2:
- Align MTU before checking if its valid
Fixes: 7ac6653a08 ("stmmac: Move the STMicroelectronics driver")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split Header feature needs to know the size of RX buffer but current
code is determining it too late. Fix this by moving the RX buffer
computation to earlier stage.
Changes from v2:
- Do not try to align already aligned buffer size
Fixes: 67afd6d1cf ("net: stmmac: Add Split Header support and enable it in XGMAC cores")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running the MC and UC filter tests we setup a multicast address
that its expected to be blocked. If the number of available multicast
registers is zero, driver will always pass the multicast packets which
will fail the test.
Check if available multicast addresses is enough before running the
tests.
Fixes: 091810dbde ("net: stmmac: Introduce selftests support")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel may sleep while holding a spinlock.
The function call path (from bottom to top) in Linux 4.19 is:
net/nfc/nci/uart.c, 349:
nci_skb_alloc in nci_uart_default_recv_buf
net/nfc/nci/uart.c, 255:
(FUNC_PTR)nci_uart_default_recv_buf in nci_uart_tty_receive
net/nfc/nci/uart.c, 254:
spin_lock in nci_uart_tty_receive
nci_skb_alloc(GFP_KERNEL) can sleep at runtime.
(FUNC_PTR) means a function pointer is called.
To fix this bug, GFP_KERNEL is replaced with GFP_ATOMIC for
nci_skb_alloc().
This bug is found by a static analysis tool STCheck written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dev_hold has to be called always in rx_queue_add_kobject.
Otherwise usage count drops below 0 in case of failure in
kobject_init_and_add.
Fixes: b8eb718348 ("net-sysfs: Fix reference count leak in rx|netdev_queue_add_kobject")
Reported-by: syzbot <syzbot+30209ea299c09d8785c9@syzkaller.appspotmail.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: David Miller <davem@davemloft.net>
Cc: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Jouni Hogander <jouni.hogander@unikie.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As flower rules are added, they are given a stats ID based on the number
of rules that can be supported in firmware. Only after the initial
allocation of all available IDs does the driver begin to reuse those that
have been released.
The initial allocation of IDs was modified to account for multiple memory
units on the offloaded device. However, this introduced a bug whereby the
counter that controls the IDs could be decremented before the ID was
assigned (where it is further decremented). This means that the stats ID
could be assigned as -1/0xfffffff which is out of range.
Fix this by only decrementing the main counter after the current ID has
been assigned.
Fixes: 467322e262 ("nfp: flower: support multiple memory units for filter offloads")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dsa_link_touch() is not exported, or defined outside of the
file it is in so make it static to avoid the following warning:
net/dsa/dsa2.c:127:17: warning: symbol 'dsa_link_touch' was not declared. Should it be static?
Signed-off-by: Ben Dooks (Codethink) <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/atheros/ag71xx.c: In function 'ag71xx_probe':
drivers/net/ethernet/atheros/ag71xx.c:1776:30: warning: passing argument 2 of
'of_get_phy_mode' makes pointer from integer without a cast [-Wint-conversion]
In file included from drivers/net/ethernet/atheros/ag71xx.c:33:
./include/linux/of_net.h:15:69: note: expected 'phy_interface_t *'
{aka 'enum <anonymous> *'} but argument is of type 'int'
Fixes: 0c65b2b90d ("net: of_get_phy_mode: Change API to solve int/unit warnings")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix missing '*' kernel-doc notation that causes this warning:
../include/linux/netdevice.h:1779: warning: bad line: spinlock
Fixes: ab92d68fc2 ("net: core: add generic lockdep keys")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk->sk_pacing_shift can be read and written without lock
synchronization. This patch adds annotations to
document this fact and avoid future syzbot complains.
This might also avoid unexpected false sharing
in sk_pacing_shift_update(), as the compiler
could remove the conditional check and always
write over sk->sk_pacing_shift :
if (sk->sk_pacing_shift != val)
sk->sk_pacing_shift = val;
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ql_alloc_large_buffers() has the usual RX buffer allocation
loop where it allocates skbs and maps them for DMA. It also
treats failure as a fatal error.
There are (at least) three bugs in the error paths:
1. ql_free_large_buffers() assumes that the lrg_buf[] entry for the
first buffer that couldn't be allocated will have .skb == NULL.
But the qla_buf[] array is not zero-initialised.
2. ql_free_large_buffers() DMA-unmaps all skbs in lrg_buf[]. This is
incorrect for the last allocated skb, if DMA mapping failed.
3. Commit 1acb8f2a7a ("net: qlogic: Fix memory leak in
ql_alloc_large_buffers") added a direct call to dev_kfree_skb_any()
after the skb is recorded in lrg_buf[], so ql_free_large_buffers()
will double-free it.
The bugs are somewhat inter-twined, so fix them all at once:
* Clear each entry in qla_buf[] before attempting to allocate
an skb for it. This goes half-way to fixing bug 1.
* Set the .skb field only after the skb is DMA-mapped. This
fixes the rest.
Fixes: 1357bfcf71 ("qla3xxx: Dynamically size the rx buffer queue ...")
Fixes: 0f8ab89e82 ("qla3xxx: Check return code from pci_map_single() ...")
Fixes: 1acb8f2a7a ("net: qlogic: Fix memory leak in ql_alloc_large_buffers")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot reported a memory leak when an allocation fails within
genradix_prealloc() for output streams. That's because
genradix_prealloc() leaves initialized members initialized when the
issue happens and SCTP stack will abort the current initialization but
without cleaning up such members.
The fix here is to always call genradix_free() when genradix_prealloc()
fails, for output and also input streams, as it suffers from the same
issue.
Reported-by: syzbot+772d9e36c490b18d51d1@syzkaller.appspotmail.com
Fixes: 2075e50caf ("sctp: convert to genradix")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Tested-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First set of fixes for v5.5. Fixing security issues, some regressions
and few major bugs.
mwifiex
* security fix for handling country Information Elements (CVE-2019-14895)
* security fix for handling TDLS Information Elements
ath9k
* fix endian issue with ath9k_pci_owl_loader
mt76
* fix default mac address handling
iwlwifi
* fix merge damage which lead to firmware crashing during boot on some devices
* fix device initialisation regression on some devices
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJd+P4eAAoJEG4XJFUm622bnOQH/RHSFFQNjxfPboZoozKb0/mT
6YtrG+0K1z8E21Os2bd+s4aRJgq1oGKDocMie5y53M38qQ5N3FchzcGopNRCRy/a
gF1PzEqceOysbEtPOx4yI+c0Gfi7rS0SjEyf2XKGowXsoIZh4j+1xlWbF/JtHt6n
J901W1GW0ZUCHaP8KuZcbsS2nfdV8tFW2NQW3Xuhy+nOdBhNRL/lKSvlhZLCCAfY
f1eJrB0rAzQpCqw8Wuz2JzWsxBiTt+6Ucuzv4EkFVrt7Xnj00feghTKJkVDqa+fL
B9hTiiYh8sLGJkYHsZLDZIzAdOW8jmun1I+XFsjdl7ucLRYz6U8NL9jc6oIGK00=
=KJmM
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-2019-12-17' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.5
First set of fixes for v5.5. Fixing security issues, some regressions
and few major bugs.
mwifiex
* security fix for handling country Information Elements (CVE-2019-14895)
* security fix for handling TDLS Information Elements
ath9k
* fix endian issue with ath9k_pci_owl_loader
mt76
* fix default mac address handling
iwlwifi
* fix merge damage which lead to firmware crashing during boot on some devices
* fix device initialisation regression on some devices
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon reusing the ptp_qoriq driver, the ptp_qoriq_free() function was
used on the remove path to free any allocated resources.
The ptp_qoriq IRQ is among these resources that are freed in
ptp_qoriq_free() even though it is also a managed one (allocated using
devm_request_threaded_irq).
Drop the resource managed version of requesting the IRQ in order to not
trigger a double free of the interrupt as below:
[ 226.731005] Trying to free already-free IRQ 126
[ 226.735533] WARNING: CPU: 6 PID: 749 at kernel/irq/manage.c:1707
__free_irq+0x9c/0x2b8
[ 226.743435] Modules linked in:
[ 226.746480] CPU: 6 PID: 749 Comm: bash Tainted: G W
5.4.0-03629-gfd7102c32b2c-dirty #912
[ 226.755857] Hardware name: NXP Layerscape LX2160ARDB (DT)
[ 226.761244] pstate: 40000085 (nZcv daIf -PAN -UAO)
[ 226.766022] pc : __free_irq+0x9c/0x2b8
[ 226.769758] lr : __free_irq+0x9c/0x2b8
[ 226.773493] sp : ffff8000125039f0
(...)
[ 226.856275] Call trace:
[ 226.858710] __free_irq+0x9c/0x2b8
[ 226.862098] free_irq+0x30/0x70
[ 226.865229] devm_irq_release+0x14/0x20
[ 226.869054] release_nodes+0x1b0/0x220
[ 226.872790] devres_release_all+0x34/0x50
[ 226.876790] device_release_driver_internal+0x100/0x1c0
Fixes: d346c9e86d ("dpaa2-ptp: reuse ptp_qoriq driver")
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently noticed that we're tracking programs related to local storage maps
through their prog pointer. This is a wrong assumption since the prog pointer
can still change throughout the verification process, for example, whenever
bpf_patch_insn_single() is called.
Therefore, the prog pointer that was assigned via bpf_cgroup_storage_assign()
is not guaranteed to be the same as we pass in bpf_cgroup_storage_release()
and the map would therefore remain in busy state forever. Fix this by using
the prog's aux pointer which is stable throughout verification and beyond.
Fixes: de9cbbaadb ("bpf: introduce cgroup storage maps")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: Roman Gushchin <guro@fb.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/1471c69eca3022218666f909bc927a92388fd09e.1576580332.git.daniel@iogearbox.net
* disable AQL on most drivers, addressing the iwlwifi issues
* fix double-free on network namespace changes
* fix TID field in frames injected through monitor interfaces
* fix ieee80211_calc_rx_airtime()
* fix NULL pointer dereference in rfkill (and remove BUG_ON)
-----BEGIN PGP SIGNATURE-----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=tvTq
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-net-2019-10-16' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A handful of fixes:
* disable AQL on most drivers, addressing the iwlwifi issues
* fix double-free on network namespace changes
* fix TID field in frames injected through monitor interfaces
* fix ieee80211_calc_rx_airtime()
* fix NULL pointer dereference in rfkill (and remove BUG_ON)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Selecting MSCC_OCELOT_SWITCH is not possible when NET_VENDOR_MICROSEMI
is disabled:
WARNING: unmet direct dependencies detected for MSCC_OCELOT_SWITCH
Depends on [n]: NETDEVICES [=y] && ETHERNET [=n] && NET_VENDOR_MICROSEMI [=n] && NET_SWITCHDEV [=y] && HAS_IOMEM [=y]
Selected by [m]:
- NET_DSA_MSCC_FELIX [=m] && NETDEVICES [=y] && HAVE_NET_DSA [=y] && NET_DSA [=y] && PCI [=y]
Add a Kconfig dependency on NET_VENDOR_MICROSEMI, which also implies
CONFIG_NETDEVICES.
Depending on a vendor config violates menuconfig locality for the DSA
driver, but is the smallest compromise since all other solutions are
much more complicated (see [0]).
https://www.spinics.net/lists/netdev/msg618808.html
Fixes: 5605194877 ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the implementation of gmac_setup_txqs() the allocated desc_ring is
leaked if TX queue base is not aligned. Release it via
dma_free_coherent.
Fixes: 4d5ae32f5e ("net: ethernet: Add a driver for Gemini gigabit ethernet")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were several issues with 53568438e3 ("net: dsa: b53: Add support for port_egress_floods callback") that resulted in breaking connectivity for standalone ports:
- both user and CPU ports must allow unicast and multicast forwarding by
default otherwise this just flat out breaks connectivity for
standalone DSA ports
- IP multicast is treated similarly as multicast, but has separate
control registers
- the UC, MC and IPMC lookup failure register offsets were wrong, and
instead used bit values that are meaningful for the
B53_IP_MULTICAST_CTRL register
Fixes: 53568438e3 ("net: dsa: b53: Add support for port_egress_floods callback")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefano Garzarella says:
====================
vsock/virtio: fix null-pointer dereference and related precautions
This series mainly solves a possible null-pointer dereference in
virtio_transport_recv_listen() introduced with the multi-transport
support [PATCH 1].
PATCH 2 adds a WARN_ON check for the same potential issue
and a returned error in the virtio_transport_send_pkt_info() function
to avoid crashing the kernel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
virtio_transport_get_ops() and virtio_transport_send_pkt_info()
can only be used on connecting/connected sockets, since a socket
assigned to a transport is required.
This patch adds a WARN_ON() on virtio_transport_get_ops() to check
this requirement, a comment and a returned error on
virtio_transport_send_pkt_info(),
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit da765a2f59 ("bpf: Add poke dependency tracking for prog array
maps") wrongly assumed that in case of prog load errors, we're cleaning
up all program tracking via bpf_free_used_maps().
However, it can happen that we're still at the point where we didn't copy
map pointers into the prog's aux section such that env->prog->aux->used_maps
is still zero, running into a UAF. In such case, the verifier has similar
release_maps() helper that drops references to used maps from its env.
Consolidate the release code into __bpf_free_used_maps() and call it from
all sides to fix it.
Fixes: da765a2f59 ("bpf: Add poke dependency tracking for prog array maps")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/1c2909484ca524ae9f55109b06f22b6213e76376.1576514756.git.daniel@iogearbox.net
In rfkill_register, the struct rfkill pointer is first derefernced
and then checked for NULL. This patch removes the BUG_ON and returns
an error to the caller in case rfkill is NULL.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Link: https://lore.kernel.org/r/20191215153409.21696-1-pakki001@umn.edu
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In function xenvif_disconnect_queue(), the value of queue->rx_irq is
zeroed *before* queue->task is stopped. Unfortunately that task may call
notify_remote_via_irq(queue->rx_irq) and calling that function with a
zero value results in a NULL pointer dereference in evtchn_from_irq().
This patch simply re-orders things, stopping all tasks before zero-ing the
irq values, thereby avoiding the possibility of the race.
Fixes: 2ac061ce97 ("xen/netback: cleanup init and deinit code")
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Acked-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
