This allows application developers to query the dvb-core API version
dynamically, helping developers understand whether certain features
will be available.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This allows application developers to determine which particular
command in a sequence is invalid, or failing with error.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove tuner_callback pointers from tuner driver configuration
and private state structures, replaced with a general-purpose
callback pointer within struct dvb_frontend.
A new parameter is added to the callback function, called
component. This allows us to use this callback pointer by
frontend components other than the tuner, if need be. So
far, this is only used by tuner drivers.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We don't want to push the ISDB-T definitions into the kernel until
we have a high level of confidence in the ISDB-T API. More testing
is required before this code is released.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Many thanks to Darron Broad for pointing out the obvious.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Also added some compat code for the older API.
Added more ISDB message/command suggestions, current not connected in dvb-core.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The frontends will be notified (if they chose) of all _get and _set commands
so they can help determine result or action. Results are now returned
to userspace correctly.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The API now assumes that ioctl calls for FE_SET_PROPERTY and all
set commands, and FE_GET_PROPERTY are get commands.
Simplification.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This helps complex demods which support different modulation types
be better informed.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For demod drivers, we want a single tuning function (set_frontend) to have
access to the properly constructed dvb_frontend_parameters structure, or
the cache values - regardless of whether the legacy or new API is being used.
This cuts down on redundant code in the demod drivers and ensures the
tuning parameters are consistent regardless of the API entry type.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After discussion the following changes were made:
1. Removed the typedefs in frontend.h, use structures.
2. In the frontend.h, remove the 16 command limit on the API and
switch to a flexible variable length API. For practical reasons
a #define limits this to 64, this should be discussed.
3. Changed dvb-core ioctl handing to deal with variable sequences
of commands.
tune-v0.0.3.c is required to use this API, it contains the interface changes.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The group preferred dtv_ over tv_, this implements it.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Hans Werner for finding the problem.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
SET_TONE and SET_VOLTAGE were not previously implemented. Two options
existed. Either cut/paste from the previous ioctl handler into the
process_properties function, which is code duplication. Or, split
the current ioctl handler into it's two major pieces.
Piece 1, responsible for input validation and semaphore acquiring
Piece 2 the processing of the previous ioctls
and finally, a new third pieces where the array of properties
is processed, and can freely call the legacy ioctl handler without
having to re-acquire the fepriv->sem semaphore. This is a clean approach
and ensures the existing legacy ioctls are processed as they were previously
(but with an extra function call) and allows the new API to share code
without duplication.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is an experimental patch to add a new tuning mechanism for
dvb frontends. Rather than passing fixed structures across the
user/kernel boundary, which need to be revised for each new modulation
type (or feature the kernel developers want to add), this implements
a simpler message based approach, allowing fe commands to be broken
down into a series of small fixed size transactions, presented
in an array.
The goal is to avoid changing the user/kernel ABI in the future, by
simply creating new frontend commands (and sequencies of commands) that
help us add support for brand new demodulator, delivery system or
statistics related commmands.
known issues:
checkpatch voilations
feedback from various developers yet to be implemented, relating
to namespace conventions, variable length array passing conventions,
and generally some optimization.
This patch should support all existing tuning mechanisms through the
new API, as well as adding 8PSK, DVB-S2 NBC-QPSK and ISDB-T API support.
For testing and exercise purposes, see the latest tune.c tool
available from http://www.steventoth.net/linux/s2
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The functions dvb_dmxdev_section_callback, dvb_dmxdev_ts_callback,
dvb_dmx_swfilter_packet, dvb_dmx_swfilter_packets, dvb_dmx_swfilter and
dvb_dmx_swfilter_204 may be called from both interrupt and process
context. Therefore they need to be protected by spin_lock_irqsave()
instead of spin_lock().
This fixes a deadlock discovered by lockdep.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixed a lot of sparse warnings: mostly warnings about shadowed variables
and signed/unsigned mismatches.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
device_create() is race-prone, so use the race-free
device_create_drvdata() instead as device_create() is going away.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
split the suckers into kernel-memory and user-memory versions,
annotate both properly.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
According to RFC 4326 (4.1) D-bit is MSB in net-endian 16bit.
dvb_net.c did
/* Set D-bit for CRC32 verification,
* if it was set originally. */
ulen |= 0x0080;
which works of little-endian (htons(1<<15) is 0x0080 there), but breaks
on big-endian.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Now that we have a specific lock to protect the network
device unicast and multicast lists, remove extraneous
grabs of the TX lock in cases where the code only needs
address list protection.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add netif_addr_{lock,unlock}{,_bh}() helpers.
Use them to protect operations that operate on or read
the network device unicast and multicast address lists.
Also use them in cases where the code simply wants to
block calls into the driver's ->set_rx_mode() and
->set_multicast_list() methods.
Signed-off-by: David S. Miller <davem@davemloft.net>
This change addresses kernel bug #10459: In kernel 2.6.25 the
budget_av driver polls for an CI slot in 100ms intervals (because no
interrupt solution for budget_av cards is feasible due to HW reasons).
If no CI/CAM is connected to the DVB card, polling times out only after 250ms.
This periodic polling leads to high CPU load.
The change increases the polling interval for empty slots from 100ms to 5s.
Intervals for remaining slot states (invalid, in progress, ready) are unchanged,
as they are either temporary conditions or no timeout should occur.
Signed-off-by: Robert Schedel <r.schedel@yahoo.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There were several issues in the past, caused by the hybrid tuner design, since
now, the same tuner can be used by drivers/media/dvb and drivers/media/video.
Kconfig items were rearranged, to split V4L/DVB core from their drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Implementation of DMX_SET_BUFFER_SIZE for dvr.
Synchronization of the code of DMX_SET_BUFFER_SIZE for demux and dvr.
Signed-off-by: Andrea Odetti <mariofutire@gmail.com>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch fixes the bug in DMX_SET_BUFFER_SIZE for the demux.
Basically it resets read and write pointers to 0 in case they are
beyond the new size of the buffer.
Signed-off-by: Andrea Odetti <mariofutire@gmail.com>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The adapter_nr module options can be used to allocate static adapter
numbers on a driver level. It avoids problems with changing DVB apapter
numbers after warm/cold boot or device unplugging and repluging.
Each driver holds DVB_MAX_ADAPTER long array of the preferred order of
adapter numbers.
options dvb-usb-dib0700 adapter_nr=7,6,5,4,3,2,1,0 would result in a
reversed allocation of adapter numbers.
With adapter_nr=2,5 it tries first to get adapter number 2 and 5. If
both are already in use it will allocate the lowest free adapter number.
Signed-off-by: Janne Grunau <janne-dvb@grunau.be>
Acked-by: Hermann Pitton <hermann.pitton@arcor.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Previously, the macro DVR_FEED, which is used to recognize and filter
out duplicate packets going to the DVR device, used the TS_PAYLOAD_ONLY
flag to identify a packet's destination.
This kind of filtering was introduced by the following two changesets:
Now, that it is possible to record TS PIDs using the demux device by
setting the output type to DMX_OUT_TSDEMUX_TAP, checking TS_PAYLOAD_ONLY
is not sufficient anymore. Therefore another flag, TS_DEMUX, is added to
specify the output type of a feed.
This allows multiple clients to filter the same TS PID on a demux device
simultaneously.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Currently (in linux-2.6.24, but linux-dvb hg looks similar), the
dmx_output_t in the dmx_pes_filter_params decides two things: whether
output is sent to demux0 or dvr0 (in dmxdev.c:dvb_dmxdev_ts_callback),
*and* whether to depacketise TS (in dmxdev.c:dvb_dmxdev_filter_start).
As it stands, those two things can't be set independently: output
destined for demux0 is depacketised, output for dvr0 isn't.
This is what you want for capturing multiple audio streams from the same
multiplex simultaneously: open demux0 several times and send
depacketised output there. And capturing a single video stream is fine
not what you want: you want multi-open (so demux0, not dvr0), but you
want the TS nature preserved (because that's what you want on output, as
you're going to re-multiplex it with the audio).
At least one existing solution -- GStreamer -- sends all its streams
simultaneously via dvr0 and demuxes again in userland, but it seems a
bit of a shame to pick out all the PIDs in kernel, stick them back
together in kernel, and send them to userland only to get unpicked
again, when the alternative is such a small API addition.
The attached patch adds a new value for dmx_output_t:
DMX_OUT_TSDEMUX_TAP, which sends TS to the demux0 device. With this
patch and a dvb-usb-dib0700 (and UK Freeview from Sandy Heath), I can
successfully capture an audio/video PID pair into a TS file that mplayer
can play back.
Signed-off-by: Peter Hartley <pdh@utter.chaos.org.uk>
Acked-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Static memory is always initialized with 0.
- Replaced in some cases C99 comments for /* */
Signed-off-by: Douglas Schilling Landgraf <dougsland@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rather than using a pointer, include struct analog_demod_ops directly
inside struct dvb_frontend. This will allow us to use dvb_attach in
the future, along with removing the need to check the ops structure
before having to check the pointer to the method being called.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
struct analog_tuner_ops no longer has any dependencies specific
to v4l2, so we can move this into dvb_frontend.h with the rest
of the tuning structures.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
