stex_internal_copy copies an in-kernel buffer to a sg list by using
scsi_kmap_atomic_sg. Some functions calls stex_internal_copy with
sg_count in struct st_ccb, which is the value that dma_map_sg
returned. However it might be shorter than the actual number of sg
entries (if the IOMMU merged the sg entries).
scsi_kmap_atomic_sg doesn't see sg->dma_length so stex_internal_copy
should be called with the actual number of sg entries
(i.e. scsi_sg_count), because if the sg entries were merged,
stex_direct_copy wrongly think that the data length in the sg list is
shorter than the actual length.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
stex_direct_copy copies an in-kernel buffer to a sg list in order to
spoof some SCSI commands. stex_direct_copy calls dma_map_sg and then
stex_internal_copy with the value that dma_map_sg returned. It calls
scsi_kmap_atomic_sg to copy data.
scsi_kmap_atomic_sg doesn't see sg->dma_length so if dma_map_sg merges
sg entries, stex_internal_copy gets the smaller number of sg entries
than the acutual number, which means it wrongly think that the data
length in the sg list is shorter than the actual length.
stex_direct_copy shouldn't call dma_map_sg and it doesn't need since
this code path doesn't involve dma transfers. This patch removes
stex_direct_copy and simply calls stex_internal_copy with the actual
number of sg entries.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Commit 3163f725a5 introduced locking in
lpfc_sli_hbqbuf_fill_hbqs, but missed unlocking on one exit.
Reported-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
the check in the residual case has an incorrect test of scsi_status
(the logic is reversed, it should be scsi_status != 0 instead of
!scsi_status. Since we checked a few lines above that scsi_status was
non-zero, just eliminate this test
Signed-off-by: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The libsas error handler has two fairly fatal bugs
1. scsi_sas_task_done calls scsi_eh_finish_cmd() too early. This
happens if the task completes after it has been aborted but before
the error handler starts up. Because scsi_eh_finish_cmd()
decrements host_failed and adds the task to the done list, the
error handler start check (host_failed == host_busy) never passes
and the eh never starts.
2. The multiple task completion paths sas_scsi_clear_queue_... all
simply delete the task from the error queue. This causes it to
disappear into the ether, since a command must be placed on the
done queue to be finished off by the error handler. This behaviour
causes the HBA to hang on pending commands.
Fix 1. by moving the SAS_TASK_STATE_ABORTED check to an exit clause at
the top of the routine and calling ->scsi_done() unconditionally (it
is a nop if the timer has fired). This keeps the task in the error
handling queue until the eh starts.
Fix 2. by making sure every task goes through task complete followed
by scsi_eh_finish_cmd().
Tested this by firing resets across a disk running a hammer test (now
it actually survives without hanging the system)
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
arcmsr_iop_message_xfer() is called from atomic context under the
queuecommand scsi_host_template handler. James Bottomley pointed out
that the current GFP_KERNEL|GFP_DMA flags are wrong: firstly we are in
atomic context, secondly this memory is not used for DMA.
Also removed some unneeded casts.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Cc: Nick Cheng <nick.cheng@areca.com.tw>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
ioc->name is used in the printk's after ioc has been freed. Free
after prinks to fix this.
This patch fixes two use-after-free's introduced by
commit e78d5b8f1e and spotted by the
Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch makes the following needlessly global functions static:
- __iscsi_unblock_session()
- iscsi_session_state_name()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch makes the needlessly global lpfc_disable_node() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6:
modules: do not try to add sysfs attributes if !CONFIG_SYSFS
POWERPC: fix typo in pseries/power.c
PM: Remove unbalanced mutex_unlock() from dpm_resume()
UIO: fix Greg's stupid changes
stable_kernel_rules: fix must already be in mainline
ide: mark "ide=reverse" option as obsolete
Driver core: Fix error handling in bus_add_driver().
driver-core: fix kernel-doc function parameters
cpufreq: fix kobject reference count handling
slabinfo: fall back from /sys/kernel/slab to /sys/slab
Fix broken utf-8 encodings in ja_JP translation of stable_kernel_rules.txt
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/pci-2.6:
PCI: Fix wrong reference counter check for proc_dir_entry
PCI: fix up setup-bus.c #ifdef
PCI: don't load acpi_php when acpi is disabled
PCI: quirks: set 'En' bit of MSI Mapping for devices onHT-based nvidia platform
PCI: kernel-doc: fix pci-acpi warning
PCI: irq: patch for Intel ICH10 DeviceID's
PCI: pci_ids: patch for Intel ICH10 DeviceID's
PCI: AMD SATA IDE mode quirk
PCI: drivers/pcmcia/i82092.c: fix up after pci_bus_region changes
PCI: hotplug: acpiphp_ibm: Remove get device information
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (23 commits)
ehci-fsl: add PPC_MPC837x to default y
USB: POWERPC: ehci: fix ppc build
USB: usb-storage: don't access beyond the end of the sg buffer
USB: quirks and unusual_devs entry for Actions flash drive
USB: usb-storage: unusual_devs entry for Oracom MP3 player
USB: serial: move zte MF330 from sierra to option
USB: add new vernier product id to ldusb.c
USB: gadget: queue usb USB_CDC_GET_ENCAPSULATED_RESPONSE message
USB: Add another Novatel U727 ID to the device table for usbserial
USB: storage: Nikon D80 new FW still needs Fixup
USB: usb-storage: don't clear-halt when Get-Max-LUN stalls
USB: option: Added vendor id for Dell 5720 broadband modem
USB: option: Add Kyocera KPC680 ids
USB: quirks for known quirky audio devices
USB: fix previous sparse fix which was incorrect
USB: fix error handling in trancevibrator
USB: g_printer, fix empty if statement
USB: ehci-fsl: mpc834x config symbol is PPC_MPC834x, not MPC834x
USB: fix usb open suspend race in cdc-acm
USB: usb: yet another Dell wireless CDMA/EVDO modem
...
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 4835/1: Fix stale comment in struct machine_desc description
[ARM] 4829/1: add .get method to pxa-cpufreq to silence a warning
[ARM] 4828/1: fix 3 warnings in drivers/video/pxafb.c
[ARM] 4827/1: fix two warnings in drivers/i2c/busses/i2c-pxa.c
[ARM] 4826/1: Orion: Register the RTC interrupt on the TS-209
[ARM] pxa: fix clock lookup to find specific device clocks
The below implements the getgeo hook for Xen block devices. Extracted
from the xen-unstable tree where it has been used for ages.
It is useful to have because it allows things like grub2 (used by the
Debian installer images) to work in a guest domain without having to
sprinkle Xen specific hacks around the place.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch converts USB_EHCI_FSL config option into the verbose
bool, so we'll able to select it for other freescale processors
with built-in EHCI controller.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently, this setup:
CONFIG_USB_ARCH_HAS_EHCI=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_EHCI_HCD_PPC_OF=y
Will fail to build:
CC drivers/usb/host/ehci-hcd.o
drivers/usb/host/ehci-hcd.c:1018:2: error: #error "missing bus glue for ehci-hcd"
make[3]: *** [drivers/usb/host/ehci-hcd.o] Error 1
ehci-hcd.c actually contains OF_PLATFORM_DRIVER glue, so error is bogus.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1035) fixes a bug in usb_stor_access_xfer_buf() (the bug
was originally found by Boaz Harrosh): The routine must not attempt to
write beyond the end of a scatter-gather list or beyond the number of
bytes requested. It also fixes up the formatting of a few comments
and similar whitespace issues.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1033) adds a quirks entry and an unusual_devs entry for
the Actions Semiconductor flash drive. This device has a 64-byte
string descriptor, which it doesn't terminate with a 0-length packet.
Oddly enough, the reporter's logs show that when the device was
plugged in at boot time, it changes its behavior completely -- it uses
a different product ID, product string descriptor, and bDeviceClass.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1034) was written by Leonid Petrov, reported by Robert
Spitzenpfeil, and updated by me. It adds an unusual_devs entry with
the IGNORE_RESIDUE flag for the Oracom MP3 player. Together with the
change to the Get-Max-LUN routine in as1032, it makes the player usable.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move the Onda H600/ZTE MF33 device from the sierra driver to the option
driver.
The reason it was moved is because the sierra driver is starting to support
more and more sierra proprietary features, so it makes more sense to keep
sierra only devices in there.
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I have a new ldusb device to go into the device table. Jiri has merged
the change for hiddev quirks already.
From: Stephen Ware <stephen.ware@eqware.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 0cf4f2de0a introduced a bug, which
prevents sending an USB_CDC_GET_ENCAPSULATED_RESPONSE message. This
breaks the RNDIS initialization (especially / only Windoze machines
dislike this behavior...).
Signed-off-by: Benedikt Spranger <b.spranger@linutronix.de>
Signed-off-by: Jan Altenberg <jan.altenberg@linutronix.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add new BCD numbers for Nikon D80 Firmware revision v1.10 to the
unusual_devs.h file.
Signed-off-by: Konstantin Kletschke <konsti@ku-gbr.de>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1032) removes the Clear-Halt calls in
usb_stor_Bulk_max_lun(). Evidently some devices (such as the Oracom
MP3 player) really don't like to receive these requests when their
bulk endpoints aren't halted.
The only reason for adding them originally was to get an ancient
ZIP-100 drive to work. But since this device has only a single LUN,
we don't need to send it a Get-Max-LUN request at all. Adding an
unusual_devs entry for the ZIP-100 with the SINGLE_LUN flag set will
cause this step to be skipped.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this is a small patch to add support for a rebranded Novatel modem (see
http://ubuntuforums.org/archive/index.php/t-608388.html for details).
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
RESET_RESUME entries for some sound devices that need it.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The previous fix for a "sparse" warning in ehci_urb_dequeue() was
incorrect. After rescheduling interrupt transfers it returned the
URB's completion status, not status for the dequeue operation itself.
This patch resolves that issue, cleans up the code in the reschedule
path, and shrinks the object code by a dozen bytes.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
trancevibrator should not pretend success if it returns an error.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A bug every C programmer makes at some point in time...
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Craig W. Nadler <craig@nadler.us>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The config symbol for mpc834x processors is CONFIG_PPC_MPC834x,
not CONFIG_MPC834x.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this fixes a race between open and disconnect in the CDC ACM driver.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
if you fail in open() you must decrement the pm counter again.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
The option driver
- violates DMA coherency rules
- allocates ~16500 bytes in one chunk
This patch splits out the buffers and uses __get_free_page() to avoid
higher order allocations.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-By: Matthias Urlichs <matthias@urlichs.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix wrong counter check for proc_dir_entry in pci_proc_detach_device().
The pci_proc_detach_device() returns with -EBUSY before calling
remove_proc_entry() if the reference counter of proc_dir_entry is not
0. But this check is wrong and pci_proc_detach_device() always fails
because the reference counter of proc_dir_entry is initialized with 1
at creating time and decremented in remove_proc_entry(). This bug
cause strange behaviour as followings:
- Accessing /proc/bus/pci/XXXX/YY file after hot-removing pci adapter
card causes kernel panic.
- Repeating hot-add/hot-remove of pci adapter card increases files
with the same name under /proc/bus/pci/XXXX/ directory. For example:
# pwd
/proc/bus/pci/0002:09
# ls
01.0
# for i in `seq 5`
> do
> echo 0 > /sys/bus/pci/slots/0009_0032/power
> echo 1 > /sys/bus/pci/slots/0009_0032/power
> done
# ls
01.0 01.0 01.0 01.0 01.0 01.0
The pci_proc_detach_device() should check if the reference counter is
not larger than 1 instead.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use upper_32_bits(): no code changes, one less ifdef.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
According to HT spec, to get message interrupt from devices mapped to HT
interrupt message, the 'En' bit of MSI Mapping capability need to be set.
The patch do this setting in quirks code for the devices on HT-based nvidia
platform.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Andy Currid <acurrid@nvidia.com>
Signed-off-by: Peer Chen <pchen@nvidia.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix PCI kernel-doc warning:
Warning(linux-2.6.24-git12//drivers/pci/pci-acpi.c:166): No description found for parameter 'hid'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PCI: modify SATA IDE mode quirk
When initialize and resume, SB600/700/800 need to set SATA mode
correctly.
Signed-off-by: Crane Cai <crane.cai@amd.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/pcmcia/i82092.c: In function 'i82092aa_set_mem_map':
drivers/pcmcia/i82092.c:650: warning: format '%lx' expects type 'long unsigned int', but argument 3 has type 'resource_size_t'
drivers/pcmcia/i82092.c:650: warning: format '%lx' expects type 'long unsigned int', but argument 4 has type 'resource_size_t'
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/pci/hotplug/acpiphp_ibm.c:ibm_find_acpi_device() is not
large enough to accommodate data returned by the _CID method
executed from acpi_get_object_info().
This patch eliminates the problem by letting ACPI code
(instead of driver code) determine and obtain a correctly
sized buffer.
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove an unnecessary unlocking of dpm_list_mtx in the error path
in drivers/base/power/main.c:dpm_suspend() .
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes two bugs with UIO that cropped up recently in -rc1
1) WARNING: at fs/sysfs/file.c:334 sysfs_open_file when trying to open
a map addr/size file - complaining about missing sysfs_ops for ktype
2) Permission denied when reading uio/uio0/maps/map0/{addr,size} when
files are mode S_IRUGO
Also fix a typo: attr_attribute -> addr_attribute
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- it is valid only if "Probe IDE PCI devices in the PCI bus order
(DEPRECATED)" config option is used
- Greg needs to remove pci_get_device_reverse() for PCI core changes
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- If the allocation of ->priv fails, the reference on the bus
must be dropped.
- If adding the kobject fails, kobject_put must be called to
clean things up.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix drivers/base/ missing kernel-doc parameters:
Warning(linux-2.6.24-git12//drivers/base/driver.c:133): No description found for parameter 'drv'
Warning(linux-2.6.24-git12//drivers/base/driver.c:133): No description found for parameter 'kobj'
Warning(linux-2.6.24-git12//drivers/base/driver.c:133): No description found for parameter 'fmt'
Warning(linux-2.6.24-git12//drivers/base/power/main.c:530): No description found for parameter 'state'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The cpufreq core should not take an extra kobject reference count for no
reason, and then refuse to release it. This has been reported as
keeping machines from properly powering down all the way.
Signed-off-by: Balaji Rao <balajirrao@gmail.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Yi Yang <yi.y.yang@intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Frans Pop <elendil@planet.nl>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
suspend_device() can become static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
The last line of the comment preceding the definition of
acpi_pci_choose_state() is incorrect. Remove it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
CC drivers/acpi/executer/exregion.o
drivers/acpi/executer/exregion.c: In function
‘acpi_ex_pci_config_space_handler’:
drivers/acpi/executer/exregion.c:369: attention : passing argument 3 of
‘acpi_os_read_pci_configuration’ from incompatible pointer type
exposed by 10270d4838http://bugzilla.kernel.org/show_bug.cgi?id=9989
Signed-off-by: Ming Lin <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We must pin all resources and make sure the PCI subsystem
won't relocate us, as the addresses are hardwired into hardware.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This silences sparse when run on zd1211rw.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This silences a few sparse warnings. There are two more where
I can't follow the code.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes the pcicore driver to not die a horrible
crash death when inserting a cardbus card.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes the SSB watchdog access for devices without a chipcommon.
These devices have the watchdog on the extif.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes the baud settings for new devices
like the Linksys WRT350n.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
'u64' is not necessarily 'unsigned long long'
drivers/net/wireless/ath5k/base.c: In function 'ath5k_beacon_update_timers':
drivers/net/wireless/ath5k/base.c:2130: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
drivers/net/wireless/ath5k/base.c:2130: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
drivers/net/wireless/ath5k/base.c: In function 'ath5k_intr':
drivers/net/wireless/ath5k/base.c:2391: warning: format '%llx' expects type 'long long unsigned int', but argument 6 has type 'u64'
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sparse sees int -> bool cast as an error:
hw.c:3754:10: warning: cast truncates bits from constant value (ffffffea becomes 0)
Fix it by converting the rettype to int and check appropriately.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Omitted lock causes sparse warning
drivers/net/wireless/ath5k/base.c:1682:1: warning: context imbalance in 'ath5k_tasklet_rx' - different lock contexts for basic block
Add the lock to the guilty fail path.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on report from Cavan Carroll <cavancarroll@hotmail.com>:
http://bugzilla.kernel.org/show_bug.cgi?id=9863
Cc: Cavan Carroll <cavancarroll@hotmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix libata kernel-doc parameter:
Warning(linux-2.6.25-rc2-git3//drivers/ata/libata-scsi.c:845): No description found for parameter 'rq'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
this will fix crash bug when doing rmmod to the driver, this is because the
port_stop function get called later and it could access the device's registers.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Acked-by: Mark Lord <mlord@pobox.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch implements libata.force module parameter which can
selectively override ATA port, link and device configurations
including cable type, SATA PHY SPD limit, transfer mode and NCQ.
For example, you can say "use 1.5Gbps for all fan-out ports attached
to the second port but allow 3.0Gbps for the PMP device itself, oh,
the device attached to the third fan-out port chokes on NCQ and
shouldn't go over UDMA4" by the following.
libata.force=2:1.5g,2.15:3.0g,2.03:noncq,udma4
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
this fixes crash bug as the iomap table is not valid for integrated controllers.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Acked-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The sata_mv driver can be loaded as a platform device, as is done by
various Orion (ARM) based devices. The driver needs to define a module
alias for the platform driver so udev will load it automatically.
Tested with Debian on a QNAP TS-209.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Acked-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use ld_qdi and ld_winbond to avoid shadowing static int
variables qdi and winbond. The ld_ prefix refers to
legacy_data.
drivers/ata/pata_legacy.c:777:21: warning: symbol 'qdi' shadows an earlier one
drivers/ata/pata_legacy.c:128:12: originally declared here
drivers/ata/pata_legacy.c:811:21: warning: symbol 'qdi' shadows an earlier one
drivers/ata/pata_legacy.c:128:12: originally declared here
drivers/ata/pata_legacy.c:848:21: warning: symbol 'qdi' shadows an earlier one
drivers/ata/pata_legacy.c:128:12: originally declared here
drivers/ata/pata_legacy.c:882:21: warning: symbol 'qdi' shadows an earlier one
drivers/ata/pata_legacy.c:128:12: originally declared here
drivers/ata/pata_legacy.c:1040:21: warning: symbol 'winbond' shadows an earlier one
drivers/ata/pata_legacy.c:129:12: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When deleting the veth driver, veth_close calls netif_carrier_off
for the two extremities of the network device. netif_carrier_off on
the peer device will fire an event and hold a reference on the peer
device. Just after, the peer is unregistered taking the rtnl_lock while
the linkwatch_event is scheduled. If __linkwatch_run_queue does not
occurs before the unregistering, unregister_netdevice will wait for
the dev refcount to reach zero holding the rtnl_lock and linkwatch_event
will wait for the rtnl_lock and hold the dev refcount.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Matheos Worku <Matheos.Worku@Sun.COM>
1) niu_enable_alt_mac() needs to be adjusted so that the mask
is computed properly for the BMAC case.
2) BMAC has 6 alt MAC addresses available, not 7.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'agp-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/agp-2.6:
agp: fix missing casts that produced a warning.
agp: add support for 662/671 to agp driver
fix historic ioremap() abuse in AGP
agp/sis: Suspend support for SiS AGP
agp/sis: Clear bit 2 from aperture size byte as well
* 'drm-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/sis: add pciid for SiS 662/671 chipset
drm: add new rv380 pciid
drm: add support for passing state into the suspend hooks.
drm/i915: Fix hibernate save/restore of VGA attribute regs
drm/i915 more registers for S3 (DSPCLK_GATE_D, CACHE_MODE_0, MI_ARB_STATE)
drm/i915: restore pipeconf regs unconditionally
drm/i915: save/restore interrupt state
drm: convert drm from nopage to fault.
i915: wrap chipset types requiring hw status set ioctl
drm/radeon: add initial rs690 support to drm.
TSC is used even on machines when CONFIG_X86_TSC is not set (X86_TSC
means _require_ TSC), but it is not properly disabled when it is
unusable, because ACPI code understood the config switch as "may use
TSC".
This actually fixes suspend problems on my x60.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch fixes two NULL dereferences introduced by commit
06386bbfd2 and spotted by the Coverity
checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mthca: Free correct MPT on error exit from mthca_fmr_alloc()
IPoIB/cm: Fix ipoib_cm_dev_stop() cleanup when drain times out
In hibernate, we may end up calling the VGA save regs function twice, so we need to make sure it's idempotent. That means leaving ARX in index mode after the first save operation. Fixes hibernate on 965.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Failing to preserve the MI_ARB_STATE register was causing FIFO underruns on
the VGA output on my HP 2510p after resume.
Signed-off-by: Dave Airlie <airlied@redhat.com>
On many chipsets, the checks for DPLL enable or VGA mode will prevent the pipeconf regs from being restored, which could result in a blank display or X failing to come back after resume. So restore them unconditionally along with actually restoring pipe B's palette correctly.
Signed-off-by: Dave Airlie <airlied@redhat.com>
On resume, if the interrupt state isn't restored correctly, we may end
up with a flood of unexpected or ill-timed interrupts, which could cause
the kernel to disable the interrupt or vblank events to happen at the
wrong time. So save/restore them properly.
Signed-off-by: Dave Airlie <airlied@linux.ie>
Remove redundant vma range checks.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
When mthca_fmr_alloc() returns an error, it should free the MPT at the
index key, not mr->ibmr.lkey, since the lkey has been mangled by
hw_index_to_key() and no longer is the real index. This bug causes
corruption of the MPT table free bitmap when mthca_fmr_alloc() fails.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit efcd9971 ("IPoIB/cm: Factor out ipoib_cm_free_rx_reap_list()")
introduced a bug in ipoib_cm_dev_stop() when the receive drain times
out. In that case, the function moves all the pending rx stuff into a
private list but then calls ipoib_cm_free_rx_reap_list(), which
handles a different list.
Fix this by moving everything to the rx_reap_list that will actually
get freed up.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=906>.
Signed-off-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This fixes a bug that can't handle a passthru command with more than
two sg entries.
Big thanks to Tim Pepper for debugging the problem.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Mark Salyzyn <Mark_Salyzyn@adaptec.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] qdio: FCP/SCSI write I/O stagnates on LPAR
[S390] Fix futex_atomic_cmpxchg_std inline assembly.
[S390] dcss: Fix Unlikely(x) != y
[S390] sclp: clean up send/receive naming scheme
[S390] etr: fix compile error on !SMP
[S390] qdio: fix qdio_activate timeout handling.
[S390] Initialize per cpu lowcores on cpu hotplug.
[S390] find bit corner case.
[S390] dasd: fix locking in __dasd_device_process_final_queue
[S390] Make sure enabled wait psw is loaded in default_idle.
[S390] Let NR_CPUS default to 32/64 on s390/s390x.
[S390] cio: Do timed recovery on workqueue.
[S390] cio: Remember to initialize recovery_lock.
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
libata: implement drain buffers
libata: eliminate the home grown dma padding in favour of
block: clear drain buffer if draining for write command
block: implement request_queue->dma_drain_needed
block: add request->raw_data_len
block: update bio according to DMA alignment padding
libata: update ATAPI overflow draining
elevator: make elevator_get() attempt to load the appropriate module
cfq-iosched: add hlist for browsing parallel to the radix tree
block: make blk_rq_map_user() clear ->bio if it unmaps it
fs/block_dev.c: remove #if 0'ed code
make struct def_blk_aops static
make blk_settings_init() static
make blk_ioc_init() static
make blk-core.c:request_cachep static again
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] HP ProLiant WatchDog driver
[WATCHDOG] blackfin Watchdog driver: relocate all strings used in __init functions to __initdata
[WATCHDOG] Convert mtx1 wdt to be a platform device and use generic GPIO API
[WATCHDOG] Add support for SB1 hardware watchdog
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (60 commits)
[NIU]: Bump driver version and release date.
[NIU]: Fix BMAC alternate MAC address indexing.
net: fix kernel-doc warnings in header files
[IPV6]: Use BUG_ON instead of if + BUG in fib6_del_route.
[IPV6]: dst_entry leak in ip4ip6_err. (resend)
bluetooth: do not move child device other than rfcomm
bluetooth: put hci dev after del conn
[NET]: Elminate spurious print_mac() calls.
[BLUETOOTH] hci_sysfs.c: Kill build warning.
[NET]: Remove MAC_FMT
net/8021q/vlan_dev.c: Use print_mac.
[XFRM]: Fix ordering issue in xfrm_dst_hash_transfer().
[BLUETOOTH] net/bluetooth/hci_core.c: Use time_* macros
[IPV6]: Fix hardcoded removing of old module code
[NETLABEL]: Move some initialization code into __init section.
[NETLABEL]: Shrink the genl-ops registration code.
[AX25] ax25_out: check skb for NULL in ax25_kick()
[TCP]: Fix tcp_v4_send_synack() comment
[IPV4]: fix alignment of IP-Config output
Documentation: fix tcp.txt
...
If running on LPAR, qdio might overlook an incoming buffer in certain
scenarios. The patch makes sure that incoming buffers are detected
immediately in all situations.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make state change events adjust the correct mask by cleaning up
naming inconsistencies. Also remove chance for lockup by removing
unnecessary mask related check before reading events.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Current code in qdio_activate waits for at least 5 seconds
until it returns. It may return earlier if an error occurs,
but not if everything is ok. This large timeout value
became visible with commit dfa77f611f
"qdio: set QDIO_ACTIVATE_TIMEOUT to 5s", which intended to
fix the timeout value which was zero. In turn setting an
FCP adapter online took 5 seconds.
In practice waiting for 5ms before continuing is sufficient
as pointed out by Utz Bacher and Cornelia Huck.
Cc: Utz Bacher <utz.bacher@de.ibm.com>
Cc: Jan Glauber <jan.glauber@de.ibm.com>
Cc: Ursula Braun <braunu@de.ibm.com>
Cc: Martin Peschke <mp3@de.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
After setting the status of the cqr and releasing the lock for the
block cqr queue, we call the cqr callback function, which will usually
just trigger the dasd_block_tasklet. But when the tasklet is already
running the cqr might be processed before we invoke the callback
function. In rare cases the callback pointer may already be invalid
by the time we want to call it, which will result in a panic.
Solution: Call the callback function first and then release the lock.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We can't do our recovery in softirq context, so we schedule it from
our timer function.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This just updates the libata slave configure routine to take advantage
of the block layer drain buffers. It also adjusts the size lengths in
the atapi code to add the drain buffer to the DMA length so the driver
knows it can rely on it.
I suspect I should also be checking for AHCI as well as ATA_DEV_ATAPI,
but I couldn't see how to do that easily.
tj: * atapi_drain_needed() added such that draining is applied to only
misc ATAPI commands.
* q->bounce_gfp used when allocating drain buffer.
* Now duplicate ATAPI PIO drain logic dropped.
* ata_dev_printk() used instead of sdev_printk().
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
that provided by the block layer
ATA requires that all DMA transfers begin and end on word boundaries.
Because of this, a large amount of machinery grew up in ide to adjust
scatterlists on this basis. However, as of 2.5, the block layer has a
dma_alignment variable which ensures both the beginning and length of a
DMA transfer are aligned on the dma_alignment boundary. Although the
block layer does adjust the beginning of the transfer to ensure this
happens, it doesn't actually adjust the length, it merely makes sure
that space is allocated for transfers beyond the declared length. The
upshot of this is that scatterlists may be padded to any size between
the actual length and the length adjusted to the dma_alignment safely
knowing that memory is allocated in this region.
Right at the moment, SCSI takes the default dma_aligment which is on a
512 byte boundary. Note that this aligment only applies to transfers
coming in from user space. However, since all kernel allocations are
automatically aligned on a minimum of 32 byte boundaries, it is safe to
adjust them in this manner as well.
tj: * Adjusting sg after padding is done in block layer. Make libata
set queue alignment correctly for ATAPI devices and drop broken
sg mangling from ata_sg_setup().
* Use request->raw_data_len for ATAPI transfer chunk size.
* Killed qc->raw_nbytes.
* Separated out killing qc->n_iter.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
With padding and draining moved into it, block layer now may extend
requests as directed by queue parameters, so now a request has two
sizes - the original request size and the extended size which matches
the size of area pointed to by bios and later by sgs. The latter size
is what lower layers are primarily interested in when allocating,
filling up DMA tables and setting up the controller.
Both padding and draining extend the data area to accomodate
controller characteristics. As any controller which speaks SCSI can
handle underflows, feeding larger data area is safe.
So, this patch makes the primary data length field, request->data_len,
indicate the size of full data area and add a separate length field,
request->raw_data_len, for the unmodified request size. The latter is
used to report to higher layer (userland) and where the original
request size should be fed to the controller or device.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
For misc ATAPI commands which transfer variable length data to the
host, overflow can occur due to application or hardware bug. Such
overflows can be ignored safely as long as overflow data is properly
drained. libata HSM implementation has this implemented in
__atapi_pio_bytes() and recently updated for 2.6.24-rc but it requires
further improvements. Improve drain logic such that...
* Report overflow errors using ehi desc mechanism instead of printing
directly.
* Properly calculate the number of bytes to be drained considering
actual number of consumed bytes for partial draining.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
BMAC port alternate MAC address index needs to start at 1. Index 0 is
used for the main MAC address.
Signed-off-by: Matheos Worku <matheos.worku@sun.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several AGP drivers right now use ioremap_nocache() on kernel ram in order
to turn a page of regular memory uncached.
There are two problems with this:
1) This is a total nightmare for the ioremap() implementation to keep
various mappings of the same page coherent.
2) It's a total nightmare for the AGP code since it adds a ton of
complexity in terms of keeping track of 2 different pointers to
the same thing, in terms of error handling etc etc.
This patch fixes this by making the AGP drivers use the new
set_memory_XX APIs instead.
Note: amd-k7-agp.c is built on Alpha too, and generic.c is built
on ia64 as well, which do not yet have the set_memory_*() APIs,
so for them some we have a few ugly #ifdefs - hopefully they'll
be fixed soon.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This driver reports voltage, temperature and fan sensor readings
on an ADT7473 chip.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This patch fixes the missing residual count setting in DMA mode,
which was introduced during the conversion to blk-end-request.
The residual count could be used by the request submitter.
So if it isn't set correctly, some upper layers does not work.
(e.g. wodim for CD burning.)
The bug is in only DMA mode.
In PIO mode, we are setting the residual count correctly,
so no need to fix.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Reported-by: Andreas Schwab <schwab@suse.de>
Tested-by: Andreas Schwab <schwab@suse.de>
Tested-by: Laura Garcia <nevola@gmail.com>
Tested-by: Borislav Petkov <petkovbb@googlemail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Prefetch needs to be set for some ide devices to work when connected to
a ht6560b interface. This was not always done properly, causing a system
with a HD and CD on the primary interface to not work properly. Or, in
effect, hang hard.
This patch forces prefetch on devices before checking whether it
is necessary to change the settings in the interface
This patch should also be applied to 2.4. I don't currently have a
2.4 tree around.
(also change my email address)
Signed-off-by: Jan Evert van Grootheest <janevert@caiway.nl>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
According to the datasheet, ht6560b only supports up to PIO mode 4.
[bart: manually ported it over 2.6.25-rc2]
Signed-off-by: Jan Evert van Grootheest <janevert@caiway.nl>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
[bart: manually ported it over via82cxxx changes]
From: Andrew Smith <asmith@tranquility.fsbusiness.co.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
commit 8ac4ce742c ("ide: fix host drivers
depending on ide_generic to probe for interfaces (take 2)") moved probing
to falconide but forgot to take care of Atari specific locking - fix it.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
commit 29dd59755a ("ide: remove ide_setup_ports")
forgot to take into account the base addresses for the CONTROL registers for
falconide and macide, as pointed out by Michael Schmitz.
Falconide was tested on Aranym.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/nes: Fix possible array overrun
RDMA/nes: Fix VLAN support
RDMA/nes: Fix MAC interrupt erroneously masked on ifdown
IB: Fix return value in ib_device_register_sysfs()
In nes_create_qp(), the test
if (nesqp->mmap_sq_db_index > NES_MAX_USER_WQ_REGIONS) {
is used to error out if the db_index is too large; however, if the
test doesn't trigger, then the index is used as
nes_ucontext->mmap_nesqp[nesqp->mmap_sq_db_index] = nesqp;
and mmap_nesqp is declared as
struct nes_qp *mmap_nesqp[NES_MAX_USER_WQ_REGIONS];
which leads to an array overrun if the index is exactly equal to
NES_MAX_USER_WQ_REGIONS. Fix this by bailing out if the index is
greater than or equal to NES_MAX_USER_WQ_REGIONS.
This was spotted by the Coverity checker (CID 2162).
Acked-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Hp is providing a Hardware WatchDog Timer driver that will only work with the
specific HW Timer located in the HP ProLiant iLO 2 ASIC. The iLO 2 HW Timer
will generate a Non-maskable Interrupt (NMI) 9 seconds before physically
resetting the server, by removing power, so that the event can be logged to
the HP Integrated Management Log (IML), a Non-Volatile Random Access Memory
(NVRAM). The logging of the event is performed using the HP ProLiant ROM via
an Industry Standard access known as a BIOS Service Directory Entry.
Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch converts the MTX-1 to be a platform device, use the available
generic GPIO API for the MTX-1 board and register the miscdev alias.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Support watchdog timers built into SiByte MIPS SoCs.
Signed-off-by: Andy Sharp <andy.sharp@onstor.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Thanks to Martin Michlmayr <tbm@cyrius.com> for reporting this issue:
The zoran driver fails to compile on the ARM Orion platform with:
In file included from drivers/media/video/zoran_procfs.c:50:
drivers/media/video/zoran.h:232: error: expected identifier before numeric
constant
The reason is that drivers/media/video/zoran.h defines an enum with
GPIO_MAX in it, but Orion contains a #define GPIO_MAX 32 in
include/asm-arm/arch-orion/orion.h
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There was a possible race condition in the increment/decrement of
the active device references counter.
Thanks to Trent Piepho (xyzzy@speakeasy.org) for bringing it up.
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The initial work to convert the bttv driver to V4L2 "Partial conversion
from V4L1 to V4L2" (e84619b174), missed
the line which set the appropriate overlay crop structure in the newly
allocated bttv_buffer. This then causes a divide error in the
bttv_calc_geo function.
Signed-off-by: Robert Fitzsimons <robfitz@273k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
drivers/built-in.o: In function `set_type':
tuner-core.c:(.text+0x8879d): undefined reference to `xc5000_attach'
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The spinlock is held over too large a region: pscratch is a permanent
address (it's allocated at boot time and never changes). All you need
the smp lock for is mediating the scratch in use flag, so fix this by
moving the spinlock into the case where we set the pscratch_busy flag
to false.
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
scsi/qla2xxx/qla_dfs.c: In function 'qla2x00_dfs_fce_show':
scsi/qla2xxx/qla_dfs.c:26: warning: format '%llx' expects type 'long long unsigned int', but argument 3 has type 'uint64_t'
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The panic occurs if we get a MSGIN or MSGOUT for an unidentified SCB
(meaning we didn't identify the outstanding command it was for). For
MSGIN this is wrong because it could be an unsolicited negotiation
MSGIN from the target.
Still panic on unsolicited MSGOUT because this would represent a
mistake in the negotiation phases. However, we should fix this as
well. The specs say we should go to bus free for unexpected msgin.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
scsi_debug does at several places:
for_each_sg(sdb->table.sgl, sg, sdb->table.nents, k) {
kaddr = (unsigned char *)
kmap_atomic(sg_page(sg), KM_USER0);
We cannot do something like that with the clustering enabled (or we
can use scsi_kmap_atomic_sg).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Apparently the fix to [SCSI] fas216: Use scsi_eh API for REQUEST_SENSE
invocation didn't show up in the final version sent to linus.
Correct this omission.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
From conversations with the maintainers the _p isn't needed so kill it.
That removes the last non ISA _p user from the SCSI layer to my knowledge.
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: "Yang, Bo" <Bo.Yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Verified all the arches necessary select the CONFIG_64BIT symbol. This
also kills the warning (since it was using the 32-bit case) on parisc64
and mips64.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This driver has been failing under heavy load with
aic94xx: escb_tasklet_complete: REQ_TASK_ABORT, reason=0x6
aic94xx: escb_tasklet_complete: Can't find task (tc=4) to abort!
The second message is because the driver fails to identify the task
it's being asked to abort. On closer inpection, there's a thinko in
the for each task loop over pending tasks in both the REQ_TASK_ABORT
and REQ_DEVICE_RESET cases where it doesn't look at the task on the
pending list but at the one on the ESCB (which is always NULL).
Fix by looking at the right task. Also add a print for the case where
the pending SCB doesn't have a task attached.
Not sure if this will fix all the problems, but it's a definite first
step.
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
one system: initrd get courrupted:
RAMDISK: Compressed image found at block 0
RAMDISK: incomplete write (-28 != 2048) 134217728
crc error
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 388k freed
init_special_inode: bogus i_mode (177777)
Warning: unable to open an initial console.
init_special_inode: bogus i_mode (177777)
init_special_inode: bogus i_mode (177777)
Kernel panic - not syncing: No init found. Try passing init= option to kernel.
bisected to
commit 9927c68864
Author: James Bottomley <James.Bottomley@HansenPartnership.com>
Date: Sun Feb 3 15:48:56 2008 -0600
[SCSI] ses: add new Enclosure ULD
changes:
1. change char to unsigned char to avoid type change later.
2. preserve len for page1
3. need to move desc_ptr even the entry is not enclosure_component_device/raid.
so keep desc_ptr on right position
4. record page7 len, and double check if desc_ptr out of boundary before touch.
5. fix typo in subenclosure checking: should use hdr_buf instead.
[jejb: style fixes]
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
It currently isn't possible to open the frontend device of cx88-mpeg devices
(DVB or Blackbird) multiple times concurrently. (for instance, to attach a
signal monitoring tool while reading a stream, or to send a frequency change
ioctl) This patch fixes that condition.
Signed-off-by: Roland Stoll <roland@xindex.de>
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Do away with the need to set tuner=63 on cx88xx with recent HVR-1300 boards
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Together with Oliver Neukum from Novell, USB autosuspend support was added.
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch combines all the finished discussions and its resulting patches from
the mailing list.
The version 1.0.6 is mainly influenced by Oliver Neukum. He found a lot of
small issues, that are fixed with this patch now. For me the most interesting
thing is, that it's now safer to use it on other architectures.
The history for version 1.0.6 is:
- fixed coverity checker warnings in *_usb_driver_disconnect
- probe()/open() race by correct ordering in probe()
- DMA coherency rules by separate allocation of all buffers
- use of endianness macros
- abuse of spinlock, replaced by mutex
- racy handling of timer in disconnect, replaced by delayed_work
- racy interruptible_sleep_on(), replaced with wait_event_interruptible()
- handle signals in read()
The driver is tested with all Debian/testing radio programs and rdsd. The patch
is tested against checkpatch.pl v1.12.
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some cards need the diseqc signal modulated, while some just need
the envelope to control the LNB supply.
This fixes Bug 9887
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
fix the following build warning:
radio-si470x.c: In function 'si470x_get_rds_registers':
radio-si470x.c:562: warning: format '%ld' expects type 'long int',
but argument 3 has type 'unsigned int'
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
em28xx driver is capable of handling more than one usb device. However, isoc
transfers require a large amount of data to be transfered.
Before this patch, just one em28xx board were enough to allocate more than 50%
URBs:
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 8
B: Alloc=480/800 us (60%), #Int= 0, #Iso= 2
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
So, only one board could use an USB host at the same time. After the patch, it
is possible to use more than one em28xx at the same time, on the same usb host,
if the image size is slower or equal to 345600, since those images will
require about 30% of the URBs:
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 8
B: Alloc=232/800 us (29%), #Int= 0, #Iso= 2
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
So, in thesis, after the patch, it would be possible to use up to 3 boards by
each usb host, if the devices are generating small images.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Improves audio configurations on em28xx:
- mutes audio before changing amux;
- adds a delay after setting audio src;
- waits up to 50ms for ac97 busy.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
drivers/media/video/em28xx/em28xx-core.c: In function 'em28xx_set_audio_source':
drivers/media/video/em28xx/em28xx-core.c:276: warning: 'no_ac97' may be used uninitialized in this function
This looks like a genuine bug to me.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
'!' has a higher priority than '&': bitanding has no effect.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
videobuf functions at close() method already locks videobuf. It makes no sense
to keep the locking at empress close() method.
There is also a lock at open() method. I'm not sure if it is safe to remove the
locking there.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Improved display of still pictures (VIDEO_STILLPICTURE ioctl).
Ensure that both fields are displayed for progressive frames.
Thanks to Reinhard Nissl and Klaus Schmidinger for finding out
that the FREEZE command does this.
Thanks-to: Reinhard Nissl <rnissl@gmx.de>
Thanks-to: Klaus Schmidinger <Klaus.Schmidinger@cadsoft.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for KNC TV Station Plus X4, sub-system id 0x1894:0x0015.
Based on a patch submitted by Johannes Deisenhofer.
Thanks-to: Johannes Deisenhofer <jo.deisenhofer@googlemail.com>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thanks to Darren Salt <linux@youmustbejoking.demon.co.uk> for pointing this
issue.
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Adrian used the coverity checker against radio-si470x and found this:
> The Coverity checker spotted the following check-after-use in
> drivers/media/radio/radio-si470x.c:
>
> <-- snip -->
> static void si470x_usb_driver_disconnect(struct usb_interface *intf)
> {
> struct si470x_device *radio = usb_get_intfdata(intf);
>
> del_timer_sync(&radio->timer); <------------------
> flush_scheduled_work();
>
> usb_set_intfdata(intf, NULL);
> if (radio) { <------------------
> video_unregister_device(radio->videodev);
> kfree(radio->buffer);
> kfree(radio);
> }
> }
> <-- snip -->
>
> Either "radio" can be NULL and this case has to be properly handled or
> the NULL check is not required.
These two lines should indeed better be inside the if statement.
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch makes the following needlessly global functions static:
- em28xx-core.c:em28xx_write_reg_bits()
- em28xx-video.c:em28xx_vdev_init()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch makes the following needlessly global functions static:
- stk_sensor_outb()
- stk_sensor_inb()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Jaime Velasco Juan <jsagarribay@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
stk_camera_cleanup() can become static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Jaime Velasco Juan <jsagarribay@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
tuner_list can become static - and it's anyway a way too generic name
for a global variable - see commit b00ef4b8d8
for a completely different global variable of the same name I just made
static...
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch fixes an off-by-one error spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
saa7134-dvb: add missing dvb_attach around tda10046_attach
This patch adds a possibly missing dvb_attach for tda10046_attach.
This removes the hard dependency of saa7134-dvb on tda1004x module.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch changed the request_region() validation to avoid invalid return.
Thanks to Roland Kletzing <devzero@web.de> for bug report and data collection.
Signed-off-by: Douglas Schilling Landgraf <dougsland@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
I updated the radio-si470x driver another time. Here are the commented history entries:
- number of seek_retries changed to tune_timeout
The last versions checked for the end of frequency tuning by polling a si470x register.
Therefore polling depended on the usb utilization.
This was changed to have a constant timeout now.
- fixed problem with incomplete tune operations by own buffers
The last version used a shared buffer to assembly the USB HID reports.
It sometimes happened, that multiple functions were modifing this buffer simultanuously.
When sending such reports, the hardware returned USB stalls (-EPIPE).
Now buffers of the correct size (smaller than before) are allocated as local variables.
- optimization of variables
The size of some variables has been reduced to allow the compiler to generate more optimized code.
- improved error logging
At some important location, error checking was improved.
Especially the usb transfers to access si470x registers and the tuning functions were modified.
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch does fix potential NULL pointer dereference
due to logical typo error.
The issue is pointed out by
Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
CC: Sakari Ailus <sakari.ailus@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thanks to Angelo Lisco for his initial patch we missed and to
Ahmet Dogan Ugurel confirming such a device functional.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This adds support for analog inputs and DVB-T.
Good sensitivity for DVB-T currently needs to use analog TV first.
DVB-S support is not yet completed, but is on the way.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It also enumerates now the separate composite input at first
and adds mute ability to radio and external audio-in.
Many thanks to Daftcho Tabakov for reporting the flaws and testing.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
S-Video is unconfirmed, but likely correct.
The remote is not yet investigated.
Thanks go to Sioux for providing code and asking to fix the auto
detection.
Signed-off-by: sioux <sioux_it@libero.it>
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
printk should use KERN_* levels.
CC: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
