The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
What B44 has been locally using as B44_PHY_ADDR_NO_LOCAL_PHY is in fact
the Broadcom Ethernet switches pseudo-PHY address (30). Update the
header to use the newly introduced constant and update comments so they
are within 80 columns and consistent.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ADM6996L switch and some Broadcom switches with two MII interfaces
like the BCM5325F connected to two MACs on the SoC, used on some
routers do not return a valid value when reading the PHY id register
and Linux thinks there is no PHY at all, but that is wrong.
This patch registers a fixed phy in the arch code and then searches it
when there is no other phy in the Ethernet driver code.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the older home routers based on the Broadcom BCM47XX SoC series
are using a MAC that is supported by b44. On most of these routers not
the internal PHY of this MAC core is used, but a switch sometimes on an
external chip or integrated into the same SoC as the Ethernet core.
For this switch a special PHY driver is needed which should not be
integrated into b44 as the same switches are also used by other
Broadcom home networking SoCs which are using different Ethernet MAC
drivers. This was tested with the b53 switch driver which is currently
on its way to mainline.
If the internal PHY is not used, b44 will now search on the MDIO bus
for a phy and use the Linux phylib subsystem to register a driver.
Support for the internal PHY must stay here, because there are some
device which are suing the internal phy.
With this patch we scan the mdio bus when the sprom or nvram says that
the PHY address is 30, if a PHY was found at this address b44 uses it.
This was tested with a BCM4704, BCM4712 and BCM5354.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the phy address is 31, this means that there is no PHY connected
to this MAC at all, no internal and no external PHY. Reading these PHY
registers causes a system reset on some routers.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY address 30 means there is no local PHY, but there could be an
external PHY like a switch connected via MII. This is the case on most
embedded home routers where this driver is used.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Ethernet core supported by b44 supports an internal PHY integrated
into the mac core, which is supported by the b44 driver and an external
PHY to which the mac core is connected. This external PHY could be a
switch connected through MII, which is often the case when this core is
used on home routers. The usage of an external PHY was assumed when the
PHY address 30 was used and an internal PHY was assumed when the PHY
address was different. To verify that b44_phy_reset() was called and
checked if it worked, otherwise PHY address 30 was assumed, an external
PHY. It is better to check the register which says which PHY is
connected to the MAC instead of checking the PHY address.
The interface to an external PHY was only activated when this register
was set.
This also changes B44_FLAG_INTERNAL_PHY to B44_FLAG_EXTERNAL_PHY, it is
easier to check.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for 64 bit stats to Broadcom b44 ethernet driver.
Signed-off-by: Kevin Groeneveld <kgroeneveld@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moves the drivers for Broadcom devices into
drivers/net/ethernet/broadcom/ and the necessary Kconfig and Makefile
changes.
CC: Eilon Greenstein <eilong@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
CC: Matt Carlson <mcarlson@broadcom.com>
CC: Gary Zambrano <zambrano@broadcom.com>
CC: "Maciej W. Rozycki" <macro@linux-mips.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
