Jiri Pirko says:
====================
mlxsw: IPv4 UC router fixes
Ido says:
Patches 1-3 fix a long standing problem in the driver's init sequence,
which manifests itself quite often when routing daemons try to configure
an IP address on registered netdevs that don't yet have an associated
vPort.
Patches 4-9 add missing packet traps for the router to work properly and
also fix ordering issue following the recent changes to the driver's init
sequence.
The last patch isn't related to the router, but fixes a general problem
in which under certain conditions packets aren't trapped to CPU.
v1->v2:
- Change order of patch 7
- Add patch 6 following Ilan's comment
- Add patchset name and cover letter
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When packets enter the device they are classified to a priority group
(PG) buffer based on their PCP value. After their egress port and
traffic class are determined they are moved to the switch's shared
buffer and await transmission, if:
(Ingress{Port}.Usage < Thres && Ingress{Port,PG}.Usage < Thres &&
Egress{Port}.Usage < Thres && Egress{Port,TC}.Usage < Thres)
||
(Ingress{Port}.Usage < Min || Ingress{Port,PG} < Min ||
Egress{Port}.Usage < Min || Egress{Port,TC}.Usage < Min)
Packets scheduled to transmission through CPU port (trapped to CPU) use
traffic class 7, which has a zero maximum and minimum quotas. However,
when such packets arrive from PG 0 they are admitted to the shared
buffer as PG 0 has a non-zero minimum quota.
Allow all packets to be trapped to the CPU - regardless of the PG they
were classified to - by assigning a 10KB minimum quota for CPU port and
TC7.
Fixes: 8e8dfe9fdf ("mlxsw: spectrum: Add IEEE 802.1Qaz ETS support")
Reported-by: Tamir Winetroub <tamirw@mellanox.com>
Tested-by: Tamir Winetroub <tamirw@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before destroying the 802.1Q FID we should first remove the VID-to-FID
mapping. This makes mlxsw_sp_fid_destroy() symmetric with regards to
mlxsw_sp_fid_create().
Fixes: 14d39461b3 ("mlxsw: spectrum: Use per-FID struct for the VLAN-aware bridge")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While going over the code I noticed we are missing two rollbacks in the
port's creation error path. Add them and adjust the place of one of them
in the port's removal sequence so that both are symmetric.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ralue pack function needs to set op, otherwise it is 0 for add always.
Fixes: d5a1c749d2 ("mlxsw: reg: Add Router Algorithmic LPM Unicast Entry Register definition")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the conditions to generate an ICMP Redirect Message is that "the
packet is being forwarded out the same physical interface that it was
received from" (RFC 1812).
Therefore, we need to be able to trap such packets and let the kernel
decide what to do with them.
For each RIF, enable the loop-back filter, which will raise the LBERROR
trap whenever the ingress RIF equals the egress RIF.
Fixes: 99724c18fc ("mlxsw: spectrum: Introduce support for router interfaces")
Reported-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the following traps:
1) MTU Error: Trap packets whose size is bigger than the egress RIF's
MTU. If DF bit isn't set, traffic will continue to be routed in slow
path.
2) TTL Error: Trap packets whose TTL expired. This allows traceroute to
work properly.
3) OSPF packets.
Fixes: 7b27ce7bb9 ("mlxsw: spectrum: Add traps needed for router implementation")
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bbf2a4757b ("mlxsw: spectrum: Initialize ports at the end of
init sequence") moved ports initialization to the end of the init
sequence, which means ports are the first to be removed during fini.
Since the FDB delayed work is still active when ports are removed it's
possible for it to process FDB notifications of inactive ports,
resulting in a warning message.
Fix that by marking ports as inactive only after unregistering them. The
NETDEV_UNREGISTER event will invoke bridge's driver port removal
sequence that will cause the FDB (and FDB notifications) to be flushed.
Fixes: bbf2a4757b ("mlxsw: spectrum: Initialize ports at the end of init sequence")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After registering a netdevice it's possible for user space applications
to configure an IP address on it. From the driver's perspective, this
means a router interface (RIF) should be created for the PVID vPort.
Therefore, we must create the PVID vPort before registering the
netdevice.
Fixes: 99724c18fc ("mlxsw: spectrum: Introduce support for router interfaces")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when device configuration fails we emit errors to the kernel
log despite the fact we already get these from the EMAD transaction
layer, so remove them.
In addition to being unnecessary, removing these error messages will
allow us to reuse mlxsw_sp_port_add_vid() to create the PVID vPort
before registering the netdevice.
Fixes: 99724c18fc ("mlxsw: spectrum: Introduce support for router interfaces")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing a VLAN filter from the device we shouldn't return upon the
first error we encounter, as otherwise we'll have resources that will
never be freed nor used.
Instead, we should keep trying to free as much resources as possible in
a best effort mode.
Remove the error message as well, since we already get these from the
EMAD transaction code.
Fixes: 99724c18fc ("mlxsw: spectrum: Introduce support for router interfaces")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Literal loads of virtual addresses are subject to runtime relocation when
CONFIG_RELOCATABLE=y, and given that the relocation routines run with the
MMU and caches enabled, literal loads of relocated values performed with
the MMU off are not guaranteed to return the latest value unless the
memory covering the literal is cleaned to the PoC explicitly.
So defer the literal load until after the MMU has been enabled, just like
we do for primary_switch() and secondary_switch() in head.S.
Fixes: 1e48ef7fcc ("arm64: add support for building vmlinux as a relocatable PIE binary")
Cc: <stable@vger.kernel.org> # 4.6+
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Since asm/acpi.h is only included by linux/acpi.h when CONFIG_ACPI is
enabled, disabling the latter leads to the following build error on
arm64:
arch/arm64/mm/numa.c: In function ‘arm64_numa_init’:
arch/arm64/mm/numa.c:395:24: error: ‘arm64_acpi_numa_init’ undeclared (first use in this function)
if (!acpi_disabled && !numa_init(arm64_acpi_numa_init))
This patch include the asm/acpi.h explicitly in arch/arm64/mm/numa.c for
the arm64_acpi_numa_init() definition.
Fixes: d8b47fca8c ("arm64, ACPI, NUMA: NUMA support based on SRAT and SLIT")
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The raid0 MD personality does not start a raid0 array with any of its
data devices missing.
dm-raid was removing data/metadata device pairs unconditionally if it
failed to read a superblock off the respective metadata device of such
pair, resulting in failure to start arrays with the raid0 personality.
Avoid removing any data/metadata device pairs in case of raid0
(e.g. lvm2 segment type 'raid0_meta') thus allowing MD to start the
array.
Also, avoid region size validation for raid0.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
In commit:
d8152bf85d ("clocksource/drivers/mips-gic-timer: Convert init function to return error")
several return values were added to a void function resulting in the following warnings:
clocksource/mips-gic-timer.c: In function 'gic_clocksource_of_init':
clocksource/mips-gic-timer.c:175:3: warning: 'return' with a value, in function returning void [enabled by default]
clocksource/mips-gic-timer.c:183:4: warning: 'return' with a value, in function returning void [enabled by default]
clocksource/mips-gic-timer.c:190:3: warning: 'return' with a value, in function returning void [enabled by default]
clocksource/mips-gic-timer.c:195:3: warning: 'return' with a value, in function returning void [enabled by default]
clocksource/mips-gic-timer.c:200:3: warning: 'return' with a value, in function returning void [enabled by default]
clocksource/mips-gic-timer.c:211:2: warning: 'return' with a value, in function returning void [enabled by default]
clocksource/mips-gic-timer.c: At top level:
clocksource/mips-gic-timer.c:213:1: warning: comparison of distinct pointer types lacks a cast [enabled by default]
clocksource/mips-gic-timer.c: In function 'gic_clocksource_of_init':
clocksource/mips-gic-timer.c:183:18: warning: ignoring return value of 'PTR_ERR', declared with attribute warn_unused_result [-Wunused-result]
Given that the addition of the return values was intentional, it seems
that the conversion of the containing function from void to int was
simply overlooked.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Fixes: d8152bf85d ("clocksource/drivers/mips-gic-timer: Convert init function to return error")
Link: http://lkml.kernel.org/r/1471429296-9053-3-git-send-email-daniel.lezcano@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
I could not figure out why, but GCC cannot prove that the
kona_timer_init() function always initializes its two outputs,
and we get a warning for the use of the 'lsw' variable later,
which is obviously correct.
drivers/clocksource/bcm_kona_timer.c: In function 'kona_timer_init':
drivers/clocksource/bcm_kona_timer.c:119:13: error: 'lsw' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Slightly reordering the loop makes the warning disappear, after
it becomes more obvious to the compiler that the loop is
always entered on the first iteration.
As pointed out by Ray Jui, there is a related problem in the
way we deal with the loop running into the limit, as we just
keep going there with an invalid counter data, so instead we
now propagate a -ETIMEDOUT result to the caller.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: bcm-kernel-feedback-list@broadcom.com
Link: http://lkml.kernel.org/r/1471429296-9053-2-git-send-email-daniel.lezcano@linaro.org
Link: https://patchwork.kernel.org/patch/9174261/
Signed-off-by: Ingo Molnar <mingo@kernel.org>
While converting the init function to return an error, the wrong clock
was get. This leads to the wrong clock rate and slows down the kernel.
For example, it affects typical boot time:
- without fix: over 1 minute
- with fix: 15 seconds
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 12549e27c6 ("clocksource/drivers/time-armada-370-xp: Convert init function to return error")
Link: http://lkml.kernel.org/r/1471429296-9053-1-git-send-email-daniel.lezcano@linaro.org
[ Refined the changelog. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When we're really tight on space, xfs_alloc_ag_vextent_small() can
allocate a block from the AGFL and give it to the caller. Since the
caller is never the AGFL-fixing method, we must remove the OWN_AG
reverse mapping because it will clash with whatever rmap the caller
wants to set up. This bug was discovered by running generic/299
repeatedly.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
- Test fixes.
- A vsock fix.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXsSOEAAoJECgfDbjSjVRpmCIIAKe6m+gWBiC4GJHJTYP5Q+lR
c6meEwxMBTZ+EVSeqUrAIN7slXu/w4NMVE/7IOo9Y+OUGK9MpQiRDOTzw2m3ps8d
W2gEJ+kvc7wFZZKXPkrgvzSuct0yv2Ho+lhZ9wpENU8KulyjBjAZ4xUDw/4LPM7G
nmE8GwOx625N4KCJh3dw5jZsgdyVWzqPuVYUqFctOWdDEqEs4f/Zb3kHR81DoMai
crri3p0fDOo+9zYPDTteG1ILayY6yIIFiPx8jrHTdL9DS+LcBHYJMXunu4Ensjth
9xdJeqWyb20DjSjzhrjwxS7Li4FJDiG5xYHNfuf2OQb+Or7ZvUGga1PbaNa7m6I=
=nlXU
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio/vhost fixes from Michael Tsirkin:
- test fixes
- a vsock fix
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
tools/virtio: add dma stubs
vhost/test: fix after swiotlb changes
vhost/vsock: drop space available check for TX vq
ringtest: test build fix
Pull s390 fixes from Martin Schwidefsky:
"A couple of bug fixes, minor cleanup and a change to the default
config"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/dasd: fix failing CUIR assignment under LPAR
s390/pageattr: handle numpages parameter correctly
s390/dasd: fix hanging device after clear subchannel
s390/qdio: avoid reschedule of outbound tasklet once killed
s390/qdio: remove checks for ccw device internal state
s390/qdio: fix double return code evaluation
s390/qdio: get rid of spin_lock_irqsave usage
s390/cio: remove subchannel_id from ccw_device_private
s390/qdio: obtain subchannel_id via ccw_device_get_schid()
s390/cio: stop using subchannel_id from ccw_device_private
s390/config: make the vector optimized crc function builtin
s390/lib: fix memcmp and strstr
s390/crc32-vx: Fix checksum calculation for small sizes
s390: clarify compressed image code path
Use a special read-only iomap_ops implementation to support fiemap on
the attr fork.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
We'll never get nimap == 0 for a successful return from xfs_bmapi_read,
so don't try to handle it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
No need to implement it for read-only mappings.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
By bassing through an -ENOENT, similar to the old XFS implementation of
FIEMAP_FLAG_XATTR.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
[hch: split from a larger patch]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
The flag is checked as supported, but then we do an unconditional
sync of the file, regardless of whether the flag is set or not. Make
the sync conditional on having the FIEMAP_FLAG_SYNC flag set.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
iov_iter_copy_from_user_atomic disables page faults internally, no need to
do it around the call. This also brings the iomap code in line with
the original filemap version.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
This catches up with commit 2457ae ("mm: non-atomically mark page
accessed during page cache allocation where possible"), which
moved the initial access marking into the pagecache allocator.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Track the number of blocks used for the rmapbt in the AGF. When we
get to the AG reservation code we need this counter to quickly
make our reservation during mount.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
When we do DAX IO, we try to invalidate the entire page cache held
on the file. This is incorrect as it will trash the entire mapping
tree that now tracks dirty state in exceptional entries in the radix
tree slots.
What we are trying to do is remove cached pages (e.g from reads
into holes) that sit in the radix tree over the range we are about
to write to. Hence we should just limit the invalidation to the
range we are about to overwrite.
Reported-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
The space reservations was without an explaination in commit
"Add error reporting calls in error paths that return EFSCORRUPTED"
back in 2003. There is no reason to reserve disk blocks in the
transaction when allocating blocks for delalloc space as we already
reserved the space when creating the delalloc extent.
With this fix we stop running out of the reserved pool in
generic/229, which has happened for long time with small blocksize
file systems, and has increased in severity with the new buffered
write path.
[ dchinner: we still need to pass the block reservation into
xfs_bmapi_write() to ensure we don't deadlock during AG selection.
See commit dbd5c8c ("xfs: pass total block res. as total
xfs_bmapi_write() parameter") for more details on why this is
necessary. ]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
The buffer I/O accounting mechanism tracks async buffers under I/O. As
an optimization, the buffer I/O count is incremented only once on the
first async I/O for a given hold cycle of a buffer and decremented once
the buffer is released to the LRU (or freed).
xfs_buf_ioacct_dec() has an ASSERT() check for an XBF_ASYNC buffer, but
we have one or two corner cases where a buffer can be submitted for I/O
multiple times via different methods in a single hold cycle. If an async
I/O occurs first, the I/O count is incremented. If a sync I/O occurs
before the hold count drops, XBF_ASYNC is cleared by the time the I/O
count is decremented.
Remove the async assert check from xfs_buf_ioacct_dec() as this is a
perfectly valid scenario. For the purposes of I/O accounting, we really
only care about the buffer async state at I/O submission time.
Discovered-and-analyzed-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
The i40e driver was causing a kernel panic when
non-contiguous Traffic Classes, or Traffic Classes not
starting with TC0, were configured on a link partner switch.
i40e does not support non-contiguous TCs.
To fix this, the patch changes the logic when determining
the total number of TCs enabled. Before, this would use the
highest TC number enabled and assume that all TCs below it were
also enabled. Now, we create a bitmask of enabled TCs and scan
it to determine not only the number of TCs, but also if the set
of enabled TCs starts at zero and is contiguous. If not, then
DCB is disabled by only returning one TC.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
attempt_restore_of_faulty_devices() is limited to 64 when it should support
the new maximum of 253 when identifying any failed devices. It clears any
revivable devices via an MD personality hot remove and add cylce to allow
for their recovery.
Address by using existing functions to retrieve and update all failed
devices' bitfield members in the dm raid superblocks on all RAID devices
and check for any devices to clear in it.
Whilst on it, don't call attempt_restore_of_faulty_devices() for any MD
personality not providing disk hot add/remove methods (i.e. raid0 now),
because such personalities don't support reviving of failed disks.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Back when I submitted the GSO code I messed up and dropped the support for
disabling the VLAN tag filtering via the feature bit. This patch
re-enables the use of the NETIF_F_HW_VLAN_CTAG_FILTER to enable/disable the
VLAN filtering independent of toggling promiscuous mode.
Fixes: b83e30104b ("ixgbe/ixgbevf: Add support for GSO partial")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
'lvchange --refresh RaidLV' causes a mapped device suspend/resume cycle
aiming at device restore and resync after transient device failures. This
failed because flag RT_FLAG_RS_RESUMED was always cleared in the suspend path,
thus the device restore wasn't performed in the resume path.
Solve by removing RT_FLAG_RS_RESUMED from the suspend path and resume
unconditionally. Also, remove superfluous comment from raid_resume().
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
When I was adding the code for enabling VLAN promiscuous mode with SR-IOV
enabled I had inadvertently left the VLNCTRL.VFE bit unchanged as I has
assumed there was code in another path that was setting it when we enabled
SR-IOV. This wasn't the case and as a result we were just disabling VLAN
filtering for all the VFs apparently.
Also the previous patches were always clearing CFIEN which was always set
to 0 by the hardware anyway so I am dropping the redundant bit clearing.
Fixes: 1636956491 ("ixgbe: Add support for VLAN promiscuous with SR-IOV")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On LVM2 conversions via lvconvert(8), the target keeps mapped devices in
frozen state when requesting RAID devices be resynchronized. This
applies to e.g. adding legs to a raid1 device or taking over from raid0
to raid4 when the rebuild flag's set on the new raid1 legs or the added
dedicated parity stripe.
Also, fix frozen recovery for reshaping as well.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
- Add the missing <linux/io.h> header to the Intel Merrifield
driver to get rid of build mess.
- Drop two instances of pinctrl_unregister() called for drivers
using devm_* resource management.
- Remove the default debounce time for the AMD driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6AYp
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Here are a few pin control fixes for the v4.8 series, nothing special
about them:
- Add the missing <linux/io.h> header to the Intel Merrifield driver
to get rid of build mess.
- Drop two instances of pinctrl_unregister() called for drivers using
devm_* resource management.
- Remove the default debounce time for the AMD driver"
* tag 'pinctrl-v4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: intel: merrifield: Add missed header
pinctrl/amd: Remove the default de-bounce time
pinctrl: pistachio: Drop pinctrl_unregister for devm_ registered device
pinctrl: meson: Drop pinctrl_unregister for devm_ registered device
- Fix occasional decoding errors when tracing system-wide with
Intel PT (Adrian Hunter)
- Fix ip compression in Intel PT for some specific packet types not
present on current hardware (Adrian Hunter)
- Fix annotation of objects with debuginfo files (Anton Blanchard)
- Fix build on Fedora Rawhide (25) wrt using the right header to
get the major() & minor() definitions in the jitdump code, now
it is deprecated getting those using sys/types.h, one has to use
sys/sysmacros.h (Arnaldo Carvalho de Melo)
- Sync arm64/s390 kvm related header files (Arnaldo Carvalho de Melo)
- Check for dup and fdopen failures in 'perf probe' (Colin Ian King,
Arnaldo Carvalho de Melo)
- Fix showing callchains in pipe mode, i.e.
perf record -g -o - workload | perf script
now shows callchains (He Kuang)
- Show proper message when the scripts directory points to some
invalid location in 'perf script --list' (He Kuang)
- Fix 'perf mem -t store' to record 'cpu/mem-stores/P' events
again (Jiri Olsa)
- Fix ppc64le build failure when libelf is not present (Ravi Bangoria)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=VI53
-----END PGP SIGNATURE-----
Merge tag 'perf-urgent-for-mingo-20160815' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
- Fix occasional decoding errors when tracing system-wide with
Intel PT (Adrian Hunter)
- Fix ip compression in Intel PT for some specific packet types not
present on current hardware (Adrian Hunter)
- Fix annotation of objects with debuginfo files (Anton Blanchard)
- Fix build on Fedora Rawhide (25) wrt using the right header to
get the major() & minor() definitions in the jitdump code, now
it is deprecated getting those using sys/types.h, one has to use
sys/sysmacros.h (Arnaldo Carvalho de Melo)
- Sync arm64/s390 kvm related header files (Arnaldo Carvalho de Melo)
- Check for dup and fdopen failures in 'perf probe' (Colin Ian King,
Arnaldo Carvalho de Melo)
- Fix showing callchains in pipe mode, i.e.
perf record -g -o - workload | perf script
now shows callchains (He Kuang)
- Show proper message when the scripts directory points to some
invalid location in 'perf script --list' (He Kuang)
- Fix 'perf mem -t store' to record 'cpu/mem-stores/P' events
again (Jiri Olsa)
- Fix ppc64le build failure when libelf is not present (Ravi Bangoria)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
I've got reports that the Intel I-218V NIC in Intel NUC5i5RYH systems used
as a PTP slave experiences random ~10 hour clock jumps, which are resolved
if the same workaround for the 82574 and 82583 is employed, so set the
appropriate flag2 in e1000_pch_lpt_info too.
Reported-by: Rupesh Patel <rupatel@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is prepatory work for an expanding list of adapter families that have
occasional ~10 hour clock jumps when being used for PTP. Factor out the
sanitization function and convert to using a feature (bug) flag, per
suggestion from Jesse Brandeburg.
Littering functional code with device-specific checks is much messier than
simply checking a flag, and having device-specific init set flags as needed.
There are probably a number of other cases in the e1000e code that
could/should be converted similarly.
Suggested-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix PHY delay compensation math in igb_ptp_tx_hwtstamp() and
igb_ptp_rx_rgtstamp. Add PHY delay compensation in
igb_ptp_rx_pktstamp().
In the IGB driver, there are two functions that retrieve timestamps
received by the PHY - igb_ptp_rx_rgtstamp() and igb_ptp_rx_pktstamp().
The previous commit only changed igb_ptp_rx_rgtstamp(), and the change
was incorrect.
There are two instances in which PHY delay compensations should be
made:
- Before the packet transmission over the PHY, the latency between
when the packet is timestamped and transmission of the packets,
should be an add operation, but it is currently a subtract.
- After the packets are received from the PHY, the latency between
the receiving and timestamping of the packets should be a subtract
operation, but it is currently an add.
Signed-off-by: Kshitiz Gupta <kshitiz.gupta@ni.com>
Fixes: 3f544d2 (igb: adjust ptp timestamps for tx/rx latency)
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The GART aperture size can be bigger than 4GB. Therefore the offset
used in amdgpu_gart_bind and amdgpu_gart_unbind must be 64-bit.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
rtree_next_node() walks the linked list of leaf nodes to find the next
block of pages in the struct memory_bitmap. If it walks off the end of
the list of nodes, it walks the list of memory zones to find the next
region of memory. If it walks off the end of the list of zones, it
returns false.
This leaves the struct bm_position's node and zone pointers pointing
at their respective struct list_heads in struct mem_zone_bm_rtree.
memory_bm_find_bit() uses struct bm_position's node and zone pointers
to avoid walking lists and trees if the next bit appears in the same
node/zone. It handles these values being stale.
Swap rtree_next_node()s 'step then test' to 'test-next then step',
this means if we reach the end of memory we return false and leave
the node and zone pointers as they were.
This fixes a panic on resume using AMD Seattle with 64K pages:
[ 6.868732] Freezing user space processes ... (elapsed 0.000 seconds) done.
[ 6.875753] Double checking all user space processes after OOM killer disable... (elapsed 0.000 seconds)
[ 6.896453] PM: Using 3 thread(s) for decompression.
[ 6.896453] PM: Loading and decompressing image data (5339 pages)...
[ 7.318890] PM: Image loading progress: 0%
[ 7.323395] Unable to handle kernel paging request at virtual address 00800040
[ 7.330611] pgd = ffff000008df0000
[ 7.334003] [00800040] *pgd=00000083fffe0003, *pud=00000083fffe0003, *pmd=00000083fffd0003, *pte=0000000000000000
[ 7.344266] Internal error: Oops: 96000005 [#1] PREEMPT SMP
[ 7.349825] Modules linked in:
[ 7.352871] CPU: 2 PID: 1 Comm: swapper/0 Tainted: G W I 4.8.0-rc1 #4737
[ 7.360512] Hardware name: AMD Overdrive/Supercharger/Default string, BIOS ROD1002C 04/08/2016
[ 7.369109] task: ffff8003c0220000 task.stack: ffff8003c0280000
[ 7.375020] PC is at set_bit+0x18/0x30
[ 7.378758] LR is at memory_bm_set_bit+0x24/0x30
[ 7.383362] pc : [<ffff00000835bbc8>] lr : [<ffff0000080faf18>] pstate: 60000045
[ 7.390743] sp : ffff8003c0283b00
[ 7.473551]
[ 7.475031] Process swapper/0 (pid: 1, stack limit = 0xffff8003c0280020)
[ 7.481718] Stack: (0xffff8003c0283b00 to 0xffff8003c0284000)
[ 7.800075] Call trace:
[ 7.887097] [<ffff00000835bbc8>] set_bit+0x18/0x30
[ 7.891876] [<ffff0000080fb038>] duplicate_memory_bitmap.constprop.38+0x54/0x70
[ 7.899172] [<ffff0000080fcc40>] snapshot_write_next+0x22c/0x47c
[ 7.905166] [<ffff0000080fe1b4>] load_image_lzo+0x754/0xa88
[ 7.910725] [<ffff0000080ff0a8>] swsusp_read+0x144/0x230
[ 7.916025] [<ffff0000080fa338>] load_image_and_restore+0x58/0x90
[ 7.922105] [<ffff0000080fa660>] software_resume+0x2f0/0x338
[ 7.927752] [<ffff000008083350>] do_one_initcall+0x38/0x11c
[ 7.933314] [<ffff000008b40cc0>] kernel_init_freeable+0x14c/0x1ec
[ 7.939395] [<ffff0000087ce564>] kernel_init+0x10/0xfc
[ 7.944520] [<ffff000008082e90>] ret_from_fork+0x10/0x40
[ 7.949820] Code: d2800022 8b400c21 f9800031 9ac32043 (c85f7c22)
[ 7.955909] ---[ end trace 0024a5986e6ff323 ]---
[ 7.960529] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
Here struct mem_zone_bm_rtree's start_pfn has been returned instead of
struct rtree_node's addr as the node/zone pointers are corrupt after
we walked off the end of the lists during mark_unsafe_pages().
This behaviour was exposed by commit 6dbecfd345 ("PM / hibernate:
Simplify mark_unsafe_pages()"), which caused mark_unsafe_pages() to call
duplicate_memory_bitmap(), which uses memory_bm_find_bit() after walking
off the end of the memory bitmap.
Fixes: 3a20cb1779 (PM / Hibernate: Implement position keeping in radix tree)
Signed-off-by: James Morse <james.morse@arm.com>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Remove the hcd after checking for the xhci last quirks, not before.
This caused a hang on a Alpine Ridge xhci based maching which remove
the whole xhci controller when unplugging the last usb device
CC: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After a device is disconnected, xhci_stop_device() will be invoked
in xhci_bus_suspend().
Also the "disconnect" IRQ will have ISR to invoke
xhci_free_virt_device() in this sequence.
xhci_irq -> xhci_handle_event -> handle_cmd_completion ->
xhci_handle_cmd_disable_slot -> xhci_free_virt_device
If xhci->devs[slot_id] has been assigned to NULL in
xhci_free_virt_device(), then virt_dev->eps[i].ring in
xhci_stop_device() may point to an invlid address to cause kernel
panic.
virt_dev = xhci->devs[slot_id];
:
if (virt_dev->eps[i].ring && virt_dev->eps[i].ring->dequeue)
[] Unable to handle kernel paging request at virtual address 00001a68
[] pgd=ffffffc001430000
[] [00001a68] *pgd=000000013c807003, *pud=000000013c807003,
*pmd=000000013c808003, *pte=0000000000000000
[] Internal error: Oops: 96000006 [#1] PREEMPT SMP
[] CPU: 0 PID: 39 Comm: kworker/0:1 Tainted: G U
[] Workqueue: pm pm_runtime_work
[] task: ffffffc0bc0e0bc0 ti: ffffffc0bc0ec000 task.ti:
ffffffc0bc0ec000
[] PC is at xhci_stop_device.constprop.11+0xb4/0x1a4
This issue is found when running with realtek ethernet device
(0bda:8153).
Signed-off-by: Jim Lin <jilin@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enqueue the first TRB even if full_len is zero.
Without this "adb install <apk>" freezes the system.
Signed-off-by: Alban Browaeys <alban.browaeys@gmail.com>
Fixes: 86065c2719 ("xhci: don't rely on precalculated value of needed trbs in the enqueue loop")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
