The coverity checker detected a use-after-free error in
drivers/media/video/cpia2/cpia2_v4l.c::cpia2_close() (coverity
error #1281).
What happens is that we lock cam->busy_lock, then proceed to free
resources, and in the case of (--cam->open_count == 0) we finish off by
doing a kfree(cam) and then at the end of the function we do a
mutex_unlock(&cam->busy_lock) which will explode since it'll dereference
the free'd `cam' :
...
mutex_lock(&cam->busy_lock);
...
if (--cam->open_count == 0) {
...
if (!cam->present) {
video_unregister_device(dev);
kfree(cam);
}
}
mutex_unlock(&cam->busy_lock); <--- PROBLEM, cam no longer around.
...
Since this only happens in the case of open_count going down to zero I
don't see a problem with just releasing the mutex after unregistering the
device and just before the kfree(). In this case there is nothing around
that we can race against; we are in the release method, open_count is zero,
(!cam->present) and the device has just been unregistered, so letting go of
the mutex at this point looks safe to me.
Patch below to implement that solution.
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
clear EN_I2SIN_ENABLE bit for ASUS PVR-416 to enable audio
streaming in both raw video and blackbird mpeg encoder modes.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch makes the following needlessly global code static:
- pwc-ctrl.c: pwc_get_leds()
- pwc_preferred_compression
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Make two needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for FusionHDTV 3 Gold (original revision), using the
card definition for FusionHDTV3 Gold-Q
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There's a call at cx88-tvaudio to reset DMA sound on channel change; that
call was killing cx88-alsa whenever the channel was changed, resulting
in no sound. Remove those calls if cx88-alsa is selected to be compiled.
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx88-alsa was resetting the card on load, causing the IRQ IR handler
to go away (maybe others, too). There's no actual need to reset the
card, though, so that line was removed
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There was an unmasked bit in the keycodes that was causing random
behaviour (the code could be N or N+1). Masked that bit now.
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This Kconfig description is incorrect, due to a previous merge a while back.
CONFIG_SAA711X builds module saa7115, which is the newer module, and is
not obsoleted.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- fix missing line in VSB snr decoding logic for lgdt3303
Signed-off-by: Mac Michaels <wmichaels@earthlink.net>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ovcamship is used only on some USB webcams (OV511 and W9968CF)
Bettet to leave this item just after those webcams.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add detection for the LifeView3000 NTSC model (right now the PAL version is
the only one in there, which is sort of annoying for me living in the US
and all.. sigh...)
This is one of those things that I like to classify "as a works for me so
take it or leave it" :-) . Not that worried because its an $18 video
capture card that didn't look it was selling to well in the US, but then
again who knows.
The documentation needs updating too I bet but its behind anyways usually
to what is in the code.
Signed-off-by: Zac Bowling <zac@zacbowling.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix missing $() on variable name in dvb/ttpci/Makefile
Fix AV7110 firmware dependencies so that parallel builds work correctly.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Uneeded extern prototype is removed, as the function is
prototyped at media/v4l2-common.h.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch splits up dvb_pll_attach and isl6421_attach function calls
such that the lines do not exceed 80 columns. This patch is purely cosmetic,
with no functional change at all.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- moved CX88_BOARD_DVICO_FUSIONHDTV_DVB_T_DUAL frontend_attach code up
to share the #ifdef block with CX88_BOARD_DVICO_FUSIONHDTV_DVB_T_PLUS
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds support for a newer version of this device
using the zl10353 frontend instead of the mt352 frontend.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds support for a newer version of this device
using the zl10353 frontend instead of the mt352 frontend.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cinergyt2_poll()" shouldn't return (POLLIN | POLLRDNORM | POLLPRI) when
there are no pending events. User space programs that do non-bocking IO
using "select()" and/or "poll()" would otherwise produce high system load.
Acked-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Axel Dyks <xl@xlsigned.net>
Acked-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The description of the card has been updated to it's full name/model.
The tuner has also been switched to a more compatible one (radio
wasn't working, now it is)
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds support for Satelco EasyWatch DVB-S light card,
a clone of the KNC 1, with PCI subsystem ID 1894:001e
Signed-off-by: Lothar Englisch <Lothar.Englisch@lycos.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The zoran driver uses strncpy() in an unsafe way. This patch uses the proper
sizeof()-1 size parameter. Since all strncpy() targets are initialised with
memset() the trailing '\0' is already set. Where std->name was the target for
the strncpy() we overwrote 8 Bytes of the std structure with zeros.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The videodev.h and videodev2.h describe the public API for V4L and V4L2.
It shouldn't have there any kernel-specific stuff. Those were moved to
v4l2-dev.h.
This patch removes some uneeded headers and include v4l2-common.h on all
V4L driver. This header includes device implementation of V4L2 API provided
on v4l2-dev.h as well as V4L2 internal ioctls that provides connections
between master driver and its i2c devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Sub-carrier frequency for PAL/M is slicely different than NTSC/M.
Without this patch, colors don't work on PAL/M.
Setting method also improved to allow other video standards to be included.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Several common handling codes were removed. Maybe even more
stuff may be handled at common infrastructure.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Videodev now is capable of better handling V4L2 api, by
processing V4L2 ioctls and using callbacks to the driver.
The drivers should be migrated to the newer way and the older
one will be obsoleted soon.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch makes the needlessly global
alps_tdee4_stv0297_tuner_set_params() static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- use eeprom data to detect Osprey 230
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Adds support for the Y0400052 remote supplied with this card.
In addition to adding a number of buttons to the current winfast definition,
it enables all the keys currently masked out with #ifdef 0.
It is supplied separately as it remaps two keys from the current definition,
The teletext button now sends KEY_TEXT instead of KEY_SUBTITLE, as that
keycode is used by the subtitle button.
KEY_BACK was changed to KEY_LAST to group it with KEY_NEXT.
Other then that the keys don't overlap, so this should support several
different versions of the Leadtek remotes.
Signed-off-by: Malcolm Valentine <farkit@iinet.net.au>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add DVB-T and PAL-G television support for Winfast DTV2000H
Signed-off-by: Malcolm Valentine <farkit@iinet.net.au>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Enabled s-video and composite video inputs.
- Updated comments to reflect the current support for this card.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
NTSC sliced VBI support by Christopher Neufeld <television@cneufeld.ca>
with additional fixes by Hans Verkuil <hverkuil@xs4all.nl>.
Signed-off-by: Christopher Neufeld <television@cneufeld.ca>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The dvb_frontend_ops is a pointer inside dvb_frontend. That's why every demod-driver
is having a field of dvb_frontend_ops in its private-state-struct and
using the reference for filling the pointer-field in dvb_frontend.
- It saves at least two lines of code per demod-driver,
- reduces object size (one less dereference per frontend_ops-access),
- be coherent with dvb_tuner_ops,
- makes it a little bit easier for newbies to understand how it works and
- avoids stupid mistakes because you would have to copy the dvb_frontend_ops
always, before you could assign the static pointer directly, which was
dangerous.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some of the dvb_tuner_ops-pointer were set before having a dvb_frontend creating.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added support for a new cx88 card, including it's remote
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
I had broken the mt352 tuning when a non-directly connected PLL was used -
uncommon, but this is what is used on the pinnacle card.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Minor code cleanup on the genpix-module.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is a patch which includes support for the GENPIX 8PSK->USB module. The
board supports QPSK, BPSK and 8PSK decoding (though I don't think it will be
DVB-S2 compliant) With the following patch, the boad is equivalent to a budget
card (no CA Module)
The patch which adds 8psk suppot will follow, but is seperate, as it requires
DVB-S2 support
More info on the board can be found at www.genpix-electronics.com (and they
host the requisite firmwares there as well)
Signed off by: Alan Nisota <alannisota@gmail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This functionality was used when remote control input for BTTV was handled
by a standalone module, to hook some functions of that module into the main
bttv core.
Since that module is now extinct, this can go away
Signed-off-by: Ricardo Cerqueira <rmcc@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This adds support for the older (?) Pinnacle PCTV remotes (with all buttons
colored in grey). There's no autodetection for the type of remote, though;
saa7134 defaults to the colored one, to use the grey remote the
"pinnacle_remote=1" option must be passed to the saa7134 module
Signed-off-by: Sylvain Pasche <sylvain.pasche@gmail.com>
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Adds a usbvideo driver for the Logitech Quickcam Messenger USB webcam.
Signed-off-by: Jaya Kumar <jayakumar.video@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Add support for ProLink Pixelview Playtv@P7000
Raw video and MPEG encoded video confirmed to work properly.
SVideo, Composite and FM inputs are untested - disabled for now.
Signed-off-by: Angelo Marconi <am@massalombarda.net>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some code had pointless gotos that just didn't make any sense. They didn't
make the code smaller, or faster, or easier to understand.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch changes the sweeprate for TT C1500 using QAM64.
It has been proven to work using QAM64 at a SRate of 6875 for the two
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rework diseqc support to be more in line with the other demod drivers.
Fix Nova-S-Plus/Nova-SE2 diseqc.
Cleanup API.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The calls to set the pll ops were in the wrong place - moved them.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The soft reset (de)assert commands where not at the right place.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Stop/start microcontroller when changing sampling frequency to prevent
tinny audio.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The actual offset of the start of VBI data is incorrectly documented for both
the cx2388x and bt8x8. For the cx2388x, it appears to be about 220 to 224 +
VBI_V_DEL*2. The driver has been incorrectly reporting an offset of 244.
This patch adjusts VBI_V_DEL to 10, so that the offset of 244 is correct.
This is the same offset as the bttv driver, and expected by some software.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
VBI (Closed Caption, CC) capturing never worked in NTSC mode with the
cx88 driver.
They were tested with libzvbi and a patched version of tvtime.
Signed-off-by: Michael H. Schimek <mschimek@gmx.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Christoph Pfister <christophpfister@bluemail.ch>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added autodetection for PCI subsystem id 1822:0019 to use
the card definition for CX88_BOARD_DNTV_LIVE_DVB_T_PRO
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Christoph Pfister <christophpfister@bluemail.ch>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
These cards need special handling for CI - reinitialising the frontend
device when the CI module is reset. Additionally the tda10021 needs to be set
into a different transport stream mode when a CI module is present.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Since the filename of the cx23416 encoder firmware image
is defined in cx2341x.h, we don't need to explicitly define
it in cx88-blackbird.c anymore.
This changeset removes BLACKBIRD_FIRM_ENC_FILENAME,
replacing all occurrances with CX2341X_FIRM_ENC_FILENAME.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added code to cx88-blackbird.c to treat the VIDIOC_S_FREQUENCY ioctl
to stop mpeg stream before changing the frequency and restart it after.
It seems that the mpeg stream needs to be paused while changing the
channel frequency, otherwise the mpeg encoder enters into a bad state,
producing artifacts.
Signed-off-by: Valentin Zagura <puthre@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx88-blackbird uses the same encoder firmware for the cx23416 chip that is
used by ivtv and pvrusb2.
This patch alters the driver to expect the cx23416 encoder firmware to be
located in the file, "v4l-cx2341x-enc.fw", instead of using
"blackbird-fw-enc.bin"
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch removes all of the BLACKBIRD_API #define's, instead
using the equivalent CX2341X_ENC #define's in cx2341x.h
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
moved from if to ifndef.
Also added such tests at gentree script. Gentree updated to its latest
version.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix some problems regarding support for Unidirectional Lightweight
Encapsulation (ULE) in dvbnet.c.
The original ULE code was based on a draft. In the meantime, ULE has been
published in RFC 4326 (ftp://ftp.rfc-editor.org/in-notes/rfc4326.txt).
With these fixes, and some additions (which are included in the patch), the
decaps code should now be complient to RFC4326.
Signed-off-by: Christian Praehauser <cpraehaus@cosy.sbg.ac.at>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch contains the following possible cleanups:
- make the following needlessly global functions static:
- em28xx-core.c: em28xx_accumulator_set()
- em28xx-core.c: em28xx_capture_area_set()
- em28xx-core.c: em28xx_scaler_set()
- em28xx-core.c: em28xx_isocIrq()
- remove the following unused EXPORT_SYMBOL's:
- em28xx-cards.c: em28xx_boards
- em28xx-cards.c: em28xx_bcount
- em28xx-cards.c: em28xx_id_table
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
I'd missed some of these out, breaking the av7110 tuning. I then checked for
more and added them in where necessary. They may not actually be necessary
in all these locations, but if not, they'll simply have no effect.
Add small delay to stv0299 pll gate control to fix tuning problems.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added config switch to stv0297 to control i2c STOP during write behaviour.
Update frontend init in dvb-ttusb-budget.
Enable i2c STOP on other users of stv0297.
Signed-off-by: Thomas Kaiser <linux-dvb AT kaiser-linux.li>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert lnbp21.h into a linux kernel module.
Fix up previous users to use it.
Convert dvb-ttusb-budget to use it.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch contains the following possible cleanup:
- make needlessly global functions static
- remove unused #ifndef kzalloc kzalloc() #define
- remove inline's from functions
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some systems use a previous config information to generate
a default config. This seems to cause troubles on some
systems.
This patch also fixes compilation for AV7110 firmware
inside V4L/DVB tree.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Don't try and set the tuner ops if the demod was not detected.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
I'd missed the i2c gate ctrl function out of the tda10046, so tuning didn't work
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Johannes Stezenbach suggested this change - definite improvement.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rename pll calls to appropriate tuner calls.
Remove pll functions from demod structures.
Hook tuner call into tuner_ops.
Attach dvb-pll where possible.
Add pll gate control calls where appropriate.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for the AverMedia 6 Eyes MJPEG card.
- Updated drivers/media/video/Kconfig with AVS6EYES
options.
- Added CONFIG_VIDEO_ZORAN_AVS6EYES to
drivers/media/video/Makefile.
- Added I2C_DRIVERID_BT866 and I2C_DRIVERID_KS0127 to
include/linux/i2c-id.h
- Added drivers/media/video/ks0127.c, imported and modified from
the Marvel project.
- Added drivers/media/video/ks0127.h, imported and modified from
the Marvel project.
- Added drivers/media/video/bt866.c, ported from a 2.4 version
by Christer Weinigel.
- Added AVS6EYES to drivers/media/video/zoran_card.c
- Added input_mux to all cards in drivers/media/video/zoran_card.c
- Added input mux module parameter to drivers/media/video/zoran_card.c
- Added AVS6EYES to card_type in drivers/media/video/zoran.h
- Added input_mux to card_info in drivers/media/video/zoran.h
- Upped BUZ_MAX_INPUT in drivers/media/video/zoran.h from 8 to 16,
as the AVS6EYES has 10.
- Updated Documentation/video4linux/Zoran with information about AVS6EYES.
Signed-off-by: Martin Samuelsson <sam@home.se>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is a patch fixing a small bug in zc0301_start_transfer()
introduced in the ZC0301 driver v1.04.
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
I had forgotten to rename some of the tuner functions in the refactoring.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Trim excess documentation down to the essentials.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rename pll calls to appropriate tuner calls.
Remove pll functions from demod structures.
Hook tuner call into tuner_ops.
Attach dvb-pll where possible.
Add pll gate control calls where appropriate.
Sort out the hybrid cards to work with the revamped mt352/sl10353 demods
supporting external tuners.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add no_tuner setting like in mt352.
Update to use correct tuner API calls.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Make it use set_params/pllbuf as appropriate so it works with
dvb_pll_attach()ed tuners.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rename pll calls to appropriate tuner calls.
Remove pll functions from demod structures.
Hook tuner call into tuner_ops.
Attach dvb-pll where possible.
Add pll gate control calls where appropriate.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rename pll calls to appropriate tuner calls.
Remove pll functions from demod structures.
Hook tuner call into tuner_ops.
Remove BUG_ON() and convert to a soft error.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rename pll calls to appropriate tuner calls.
Remove pll functions from demod structures.
Hook tuner call into tuner_ops.
Add pll gate control calls where appropriate.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rename pll calls to appropriate tuner calls.
Add pll gate control calls where appropriate.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rename pll calls to appropriate tuner calls.
Remove pll functions from demod structures.
Hook tuner call into tuner_ops.
Add pll gate control calls where appropriate.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rename pll calls to appropriate tuner calls.
Remove pll functions from demod structures.
Hook tuner call into tuner_ops.
Attach dvb-pll where possible.
Add pll gate control calls where appropriate.
Move europa specific code from tda1104x into card driver using ops overrides
(this is how it should ebe done instead of hacking card specific code into
the demod driver).
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rename pll calls to appropriate tuner calls.
Remove pll functions from demod structures.
Hook tuner call into tuner_ops.
Add pll gate control calls where appropriate.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rename pll calls to appropriate tuner calls.
Remove pll functions from demod structures.
Hook tuner call into tuner_ops.
Add pll gate control calls where appropriate.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rename pll calls to appropriate tuner calls.
Remove pll functions from demod structures.
Hook tuner call into tuner_ops.
Add pll gate control calls where appropriate.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rename pll calls to appropriate tuner calls.
Remove pll functions from demod structures.
Hook tuner call into tuner_ops.
Add pll gate control calls where appropriate.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rename pll calls to appropriate tuner calls.
Remove pll functions from demod structures.
Hook tuner call into tuner_ops.
Add pll gate control calls where appropriate.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert to tuner_ops calls.
Remove pll function pointers from structure.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert to tuner_ops calls.
Remove pll function pointers from structure.
Remove unneeded tuner calls.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert to tuner_ops calls.
Remove pll function pointers from structure.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert to tuner_ops calls.
Remove pll function pointers from structure.
Use standardised pllbuf call.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert to tuner_ops calls.
Remove pll function pointers from structure.
Remove unneeded tuner calls.
Add i2c gate control function.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert to tuner_ops calls.
Remove pll function pointers from structure.
Remove unneeded tuner calls.
Standardise the calls used to retrieve tuner data.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Make it call the tuner calls - in case someone wants to use it to develop a
tuner without a demod.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert to tuner_ops calls.
Remove pll function pointers from structure.
Remove unneeded tuner calls.
Remove unneeded sleep function completely.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert to tuner_ops calls.
Remove pll function pointers from structure.
Remove unneeded tuner calls.
Add i2c gate control function.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert to tuner_ops calls.
Remove pll function pointer from structure.
Use standardised pllbuf function.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert to tuner_ops calls.
Remove pll function pointers from structure.
Remove unneeded tuner calls.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert to tuner_ops calls.
Remove pll function pointers from structure.
Remove unneeded tuner calls.
Add i2c gate control function.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert to tuner_ops calls.
Remove pll function pointers from structure.
Remove unneeded tuner calls.
Add i2c gate control function.
Remove europa specific hack (moved into appropriate card driver)
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert to tuner_ops calls.
Remove pll function pointers from structure.
Remove unneeded tuner calls.
Add i2c gate control function.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert to tuner_ops calls.
Remove pll function pointers from structure.
Remove unneeded tuner calls.
Add i2c gate control function.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert to tuner_ops calls.
Remove pll function pointers from structure.
Remove unneeded tuner calls.
Add i2c gate control function.
Remove extra exported function.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert to tuner_ops calls.
Remove pll function pointers from structure.
Remove unneeded tuner calls.
Add i2c gate control function.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert to tuner_ops calls.
Remove pll function pointers from structure.
Remove unneeded tuner calls.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert to tuner_ops calls.
Remove pll function pointers from structure.
Remove unneeded tuner calls.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert to tuner_ops calls.
Remove pll function pointers from structure.
Remove unneeded tuner calls.
Add i2c gate control function.
Remove extra exported pll gate control function.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert to tuner_ops calls.
Remove pll function pointers from structure.
Remove unneeded tuner calls.
Add i2c gate control function.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert to tuner_ops calls.
Remove pll function pointers from structure.
Remove unneeded tuner calls.
Add i2c gate control function.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add tuner_ops structure.
Add calls into dvb_frontend to support the new tuner architecture.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
move all pll_set functions for lg-tdvs-h06xf atsc tuners to a standalone header
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add v4l2 compatibility
Include the decompressor (legal problem has been resolv by Alan Cox)
Faster decoder and easier to maintain, optimize, ...
Can export to userland compressed stream
Support more cameras, lot of bugs are fixed.
Signed-off-by: Luc Saillard <luc@saillard.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch fixes the display name for LG TDVS-H06xF tuners
in both tuner and dvb-pll modules.
Changing the names of the actual pll_desc struct and tuner definitions
has been held back until after the dvb tuner refactoring gets merged.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch cleans up the buffer queue when the MPEG stream is closed,
preventing the message, 'cx8802_timeout'
Signed-off-by: Valentin Zagura <puthre@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- make the following needlessly global struct static:
dvb-usb/cxusb.c: cxusb_mt352_config
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The KWorld HardwareMpegTV XPert uses a multistandard tuner, tda8290 + tda8275.
Without checking the video standard in blackbird_probe, the encoder defaults
to PAL, even if the incoming video stream is NTSC. This patch checks the video
standard set by the cx2388x decoder, and sets the encoding height and frame
accordingly.
This patch is designed to only affect the KWorld HardwareMpegTV XPert.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This changeset removes pll_init, and instead sets the tuner
auxiliary byte in pll_set.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- clear I2SIN to deliver the audio stream to the cx23416 mpeg encoder.
- enable blackbird support on the KWorld HardwareMpegTV XPert
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- removed test for CX88_BOARD_HAUPPAUGE_ROSLYN prior to determining whether
the video standard in use is NTSC or PAL.
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Since I reordered the CI/frontend detection, it turns out the frontend needs
to have a GPIO set to power it on; otherwise frontend init fails.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch cleans up a potential mess that has yet to occur in the
card-specific part of cx88-tvaudio.c that sets sound input from external adc.
It may be a good idea to move this setting into cx88-cards.c in the future.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds support for KWorld MCE 200 Deluxe.
Raw video is working perfectly, MPEG capture using
cx88-blackbird is also working, but the quality
could be improved.
svideo and radio until they can be tested also.
Signed-off-by: Valentin Zagura <puthre@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch moves the EXPORT_SYMBOL's from
drivers/media/common/saa7146_vv_ksyms.c to the files with the actual
functions.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds support for the new revision of the DViCO
FusionHDTV DVB-T Lite, based on the zl10353 demod instead
of mt352.
Both mt352 and zl10353 revisions of this card have the
same PCI subsystem ID.
Acked-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Ack'd-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Currently in /sys/class/dvb/dvbX.demuxY/ we have:
dev
uevent
With the patch, we have (for a PCI DVB device):
dev
device -> ../../../devices/pci0000:00/0000:00:1e.0/0000:03:0d.0
uevent
So userspace tools can (finally) work out which physical device a DVB adapter
refers to. Previously you had to kinda look through dmesg and hope that it
hadn't been dumped out of the buffer. This makes debugging a lot easier if
the system has been up for a long time!
This is done by adding an extra 'struct device *' parameter to
dvb_register_adapter(). It will work with any kind of standard
linux 'device'. Additionally, if someone has an embedded system which does
things differently, they can simply supply 'NULL' and the behaviour will be
as before - the link will simply not appear.
Ack'd-by: Manu Abraham <manu@linuxtv.org>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Changeset 395c7c4d8f0c changed several dprintks from level 1 to level 0
(always on). They generate four lines every time DMA starts, which don't
containing any information with a use outside of debugging. This turns them
back to level 1.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If you have more than DVB_MAX_ADAPTERS in your machine, this causes an oops.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Adds the FE_GET_FRONTEND ioctl to the or51132 frontend. Current modulation is
read from the hardware, while frequency is taken from the driver's state.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- new cards should always be added to the end of the list.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The ioctl DMX_GET_EVENT has never been implemented.
I guess no software is using it because of its lack of implementation.
Future software won't use it, too, because this API doesn't make much
sense the way it is: Frontend events have their own different API.
Scrambling events can't be generated in a useful way by the hardware I
know of.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A few lines that do nothing in the or51132 frontend, removed.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
As QAM_64, QAM_256, and QAM_AUTO all use the same firmware, switching
between these modulations doesn't require a firmware re-load. This also
fixes a mishandled error condition, in which the firmware file is loaded
into the kernel, the clock mode is changed, but then the firmware upload
to the device fails. The modulation change is aborted, but the clock
mode would still be changed.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Use new routing input defines in em28xx-cards.c
- Fix S-Video settings for tvp5150-based cards (input was copied from saa7115
based cards and worked only because S-Video was selected in the default: case)
- Replace VIDIOC_S_INPUT by VIDIOC_INT_S_VIDEO_ROUTING in em28xx-video.c
- Remove the now obsolete VIDIOC_S_INPUT handler in saa7115.c
- Add VIDIOC_INT_G/S_VIDEO_ROUTING in tvp5150.c
- Add new media/tvp5150.h with the routing defines.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some saa7115-based cards use a different crystal frequency and a different
audio clock generation. Add a new VIDIOC_INT_S_CRYSTAL_FREQ command to be
able to set these values.
Also change the default APLL setting to 0. It makes no sense to have the
audio clock independent from the video clock, this can lead to audio/video
synchronization problems. Setting this to 0 is also consistent with the old
saa7114.c source and the way the Hauppauge Windows driver sets it.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- improve handling of the EXTERN input: don't start an unnecessary carrier scan
- improve the LOG_STATUS output
- ensure that a carrier scan is started again when switching back to the tuner.
- set correct prescale for L-NICAM
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There is some old code in the or51133 firmware loading function that
has no effect. Left a comment to in case it helps someone trying
to reverse engineer the chip.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Move <linux/usb_input.h> to <linux/usb/input.h> and remove some
redundant includes.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Various drivers use xmit_lock internally to synchronise with their
transmission routines. They do so without setting xmit_lock_owner.
This is fine as long as netpoll is not in use.
With netpoll it is possible for deadlocks to occur if xmit_lock_owner
isn't set. This is because if a printk occurs while xmit_lock is held
and xmit_lock_owner is not set can cause netpoll to attempt to take
xmit_lock recursively.
While it is possible to resolve this by getting netpoll to use
trylock, it is suboptimal because netpoll's sole objective is to
maximise the chance of getting the printk out on the wire. So
delaying or dropping the message is to be avoided as much as possible.
So the only alternative is to always set xmit_lock_owner. The
following patch does this by introducing the netif_tx_lock family of
functions that take care of setting/unsetting xmit_lock_owner.
I renamed xmit_lock to _xmit_lock to indicate that it should not be
used directly. I didn't provide irq versions of the netif_tx_lock
functions since xmit_lock is meant to be a BH-disabling lock.
This is pretty much a straight text substitution except for a small
bug fix in winbond. It currently uses
netif_stop_queue/spin_unlock_wait to stop transmission. This is
unsafe as an IRQ can potentially wake up the queue. So it is safer to
use netif_tx_disable.
The hamradio bits used spin_lock_irq but it is unnecessary as
xmit_lock must never be taken in an IRQ handler.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mixing "depends on I2C" and "select I2C" within the media subsystem
leads to the following problem:
Warning! Found recursive dependency: I2C DVB_BUDGET DVB_BUDGET_PATCH
DVB_AV7110 VIDEO_SAA7146_VV VIDEO_SAA7146 I2C
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
reference to .init.text: from .text between 'dvb_bt8xx_probe'
(at offset 0x122c) and 'dvb_bt8xx_remove'
reference to .init.text: from .text between 'dvb_bt8xx_probe'
(at offset 0x1267) and 'dvb_bt8xx_remove'
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If CONFIG_VIDEO_DEV=m and CONFIG_VIDEO_V4L1_COMPAT=y, v4l1-compat should
be built as a module (currently, it isn't built at all leading to
problems with modules using it).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch fixes two off-by-one errors spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
drivers/media/video/vivi.c: In function `vivi_map_sg':
drivers/media/video/vivi.c:799: error: `DMA_NONE' undeclared (first use in this function)
drivers/media/video/vivi.c:799: error: (Each undeclared identifier is reported only once
drivers/media/video/vivi.c:799: error: for each function it appears in.)
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Frequency range values in the current driver for the LG TDVS H06xF tuners
appear to have been a transposing of the 5 in the mid range 160-455 instead
of 165-450.
This patch corrects the pll programming for these tuners as per the datasheet.
Signed-off-by: Rusty Scott <rustys@ieee.org>
Signed-off-by: Mac Michaels <wmichaels1@earthlink.net>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There is a missing break in card initialization function. Might screw
up initialization of Terratec Cinergy 400 TV.
Signed-off-by: Mikhail Gusarov <dottedmag@dottedmag.net>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The fast firmware load hack in cx25840 uses private data. In fact, it
breaks pvrusb2 and doesn't work at all with ivtv. It is a unsafe
implementation and so it is removed.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch prevents a bug where the frontend is unable to tune after waking
from powered down state. Now, the device remains powered on until it is
disconnected, just like the windows driver. It seems that the bluebird
firmware is unable to successfully handle tuning after a powered down state.
This patch fixes all of the FusionHDTV Bluebird USB2 devices. The Medion
MD95700 will still behave as before, since it was unaffected by this bug.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
*) Allow forcing the bandselect value with a module parameter to
facilitate determining the correct bandselect frequencies.
*) Changes the bandselect frequency thresholds based on experiments
with the above parameter in conjunction with the values in the spec.
Signed-off-by: Yeasah Pell <yeasah at schwide.net>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
*) Sets an additional tuner parameter (demodulator sample gain) that
wasn't being set before.
*) Removes the low symbol rate tuner parameter tweaks in the previous
patch -- it appears those tweaks are not necessary with the demodulator
sample gain set correctly.
*) Cleanup and document the demodulator register initialization sequence.
*) Change set_fec routine to disable FEC auto scan when a specific code
rate is selected.
*) Remove error message when reported FEC is invalid (which happens
sometimes when the card has no signal)
Signed-off-by: Yeasah Pell <yeasah at schwide.net>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The previous DISEQC code didn't wait, so it was unreliable
Signed-off-by: Yeasah Pell <yeasah at schwide.net>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Current debug messages at cx24123 are next to useless, since they don't
print the values sent/read to registers. With this patch, debug=1 will
show comprehensive messages. debug=2 will show also read/write operations
at I2C bus.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
- fixed the reception of channels with low symbol rates.
( The VGA1 and VGA2 offsets recommended by cx24109 docs for
symbol rates from 1 to 5 MSps do not work. I changed them
to values found experimentally. The charge pump current
and FILTUNE voltage are now set to values recommended in
the docs. This improves reception for symbol rates < 15 MSps.
The values written in the SYSSymbolRate registers are calculated
with better precision. )
- fixed the cx24123_get_fec() function. It was returning the values
for DCII mode.
- removed some unused variables
Signed-off-by: Vadim Catana <skystar at moldova.cc>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In several places we use dev->devno right after we kfree() dev. This fixes
coverity bug id #1065
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L1 API is depreciated and should be removed soon from kernel. This patch
adds two new options, one to disable V4L1 drivers, and another to disable
V4L1 compat module. This way, it would be easy to check what still depends
on V4L1 stuff, allowing also to test if app works fine with V4L2 only support.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Witout this patch tv out don't work properly with my pvr350 card.
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The computation in cx88_risc_buffer suffers from the mistake:
a non-zero padding value can cause more page borders to be crossed,
leading to big buffer over-runs.
This patch changes the additive constant from 3 + 4 to 4
It also changees the constant in cx88_risc_databuffer from 3 + 4 to 2,
because 2 dwords are the correct vaule.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It looks like the HD3000 was prototyped with the 7610 tuner when
the driver was developed, but the cards appear to have always shipped
with the 7612 tuner and the driver was never adjusted for it.
The definition needs to be corrected.
- The HD-3000 was prototyped with a Thomson DTT7610,
but production versions used a DTT7612 tuner.
- This patch changes both dvb-pll settings and V4L tuner type.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Spotted a couple more places where it fails to check if
dvb_register_adapter() fails.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Now that the CI code reinitialises the frontend, need to move the CI
initialisation to after the frontend init in order to ensure the frontend is
always in a good state. Fixes an oops caused by the frontend being NULL as
well.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When disable_ir=1 parameter is used, or when saa7134_input_init1()
fails for any other reason, dev->remote will remain NULL, and the
driver will oops in saa7134_hwinit2(). Therefore dev->remote must be
checked before dereferencing.
Signed-off-by: Sergey Vlasov <vsu@altlinux.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It turns out the firmware on the TT budget-ci 1.1 slots doesn't generate
interrupts. This patch adds support for this using polling mode on these
slots.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This mutex is meant to stop two devices getting the same ID. dvbdev_get_free_id()
scans the list of already allocated devices to find a free id.
Unfortunately, since the mutex is unlocked before the card is added to the
above list, it is still possible for two of them to get the same id.
Its debatable whether this mutex lock is actually needed, but I'm unwilling
to just remove it in case something does depend on it.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There are tree mistakes on bttv_risc_overlay.
1) When skip_odd is true, the number of lines for which
instructions are written is (height+1)/2, not height/2.
2) This occurs when clipping: the number of instruction bytes
written can be as much as 8 + 12*nclips, not 8 + 8*nclips, as
currently estimated.
3) Coverity check were wrong with nskips=0, since it means that
it can clipped at most one line.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild:
kconfig: fix typo in change count initialization
kconfig: recenter menuconfig
kconfig: revert conf behaviour change
kconfig: fix default value for choice input
kbuild: fix NULL dereference in scripts/mod/modpost.c
kbuild: fix mode of checkstack.pl and other files.
kbuild: rebuild initramfs if content of initramfs changes
kbuild: properly pass options to hostcc when doing make O=..
kbuild: modules_install for external modules must not remove existing modules
kbuild: fix make dir/
ver_linux: don't print reiser4progs version if none found
kbuild: mips: fix sed regexp to generate asm-offset.h
kbuild: fix building single targets with make O=.. single-target
kbuild: use relative path to -I
kbuild: fix unneeded rebuilds in drivers/net/chelsio after moving source tree
kbuild: fix unneeded rebuilds in drivers/media/video after moving source tree
kbuild: fix garbled text in modules.txt
These are the last conversions of pci_set_dma_mask(),
pci_set_consistent_dma_mask() and pci_dma_supported() to use DMA_xBIT_MASK
constants from linux/dma-mapping.h
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Using a relative path has the advantage that when the kernel source
tree is moved the relevant .o files will not be rebuild just because
the path to the kernel src has changed.
This also got rid of a user of TOPDIR - which has been deprecated for a long time now.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
This fixes some uneeded rebuilds under drivers/media/video after moving
the source tree. The makefiles used $(src) and $(srctree) for include
paths, which is unnecessary. Changed to use relative paths.
Compile tested, produces byte-identical code to the previous makefiles.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Fix address space warning (from sparse):
drivers/media/video/cpia2/cpia2_core.c:2355:6: error: symbol 'cpia2_read' redeclared with different type (originally declared at drivers/media/video/cpia2/cpia2.h:458) - incompatible argument 2 (different address spaces)
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Renamed various msp3400 routing defines to be more consistent and less
confusing. Esp. the MSP_DSP_OUT defines were confusing since it is really
a DSP input.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Remove old DECODER_ commands from tvp5150.c, replacing them with newer
ones if appropriate.
- Small VIDIOC_G_TUNER fixes in msp3400 and tuner.
- Fix VIDIOC_S_TUNER support in em28xx.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- msp3400c did not detect the second carrier, thus being always mono.
- properly mute the msp3400c while detecting the carrier.
- fix checks on the presence of scart2/3 inputs and scart 2 output.
- implement proper audio mode fallbacks for msp3400c/d, identical to the
way msp3400g works.
- MODE_STEREO no longer produces dual languages when set for a bilingual
transmission, instead it falls back to LANG1. Use LANG1_LANG2 to hear
both languages of a bilingual transmission. This is much more intuitive
for the user and is in accordance with the preferred usage in the v4l2
specification.
- bttv tried to implement v4l2 calls with v4l1 calls to the i2c devices,
completely mangling the audmode/rxsubchans handling. v4l2 calls now do
v4l2 calls to the i2c devices.
- fixed broken i2c_vidiocschan in bttv.
- add start/end lines to LOG_STATUS.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The sliced VBI defines added in videodev2.h are removed since requires
more discussion.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch fixes a dependency problem that affected the indentation order
within the individual frontend selection support menus for cx88-dvb.
- created a boolean dependency link for VIDEO_CX88_VP3054, so that
it's tristate value will be the same as that of VIDEO_CX88_DVB.
- VIDEO_CX88_VP3054 is automatically selected by VIDEO_CX88_DVB_ALL_FRONTENDS,
but is otherwise selected by VIDEO_CX88_DVB_VP3054, offered as an option
under VIDEO_CX88_DVB_MT352
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Unfortunately on the budget-av board, the CAM reset line is tied to the
frontend reset line, so resetting the CAM also zaps the frontend. This
breaks the tda1004x at least, and causes it to fail to tune until the
budget-av module is reloaded. This patch adds an exported function to dvb_frontend
that allows a card to forcibly reinitialise a frontend. The budget-av now
does this on CAM reset, which corrects this problem.
since they do not tie the CAM reset line to the frontend reset line.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The dvr device could be opened multiple times simultaneously in O_RDONLY mode.
Each open after the first would allocate a new dvr buffer (1880 KB) and leak
the old buffer. The first close would de-allocate the dvr buffer and cause
all other open dvrs to stop working. This patch allows only a single O_RDONLY
open of the drv device, as per the API specification. Multiple O_WRONLY opens
are still allowed and don't appear to cause any problems.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
