This patch by Luke Zhang fixes a couple of issues with the WM9712
support in ac97_patch.c
Changes:-
o Fix Out3 ZC switch invert.
o Extend capture volume control to 6 bits.
o Change Mic 1 volume mask to 5 bits (31).
o Add Mic 2 volume.
Signed-off-by: Luke Zhang <lzhang@intrinsyc.com>
Signed-off-by: Liam Girdwood <liam.girdwood@wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
There are additional IDs for Si3054 codec based HDA modems. Most of
them were discovered on discuss@linmodems.org list - Thanks to MarvS
and all linmodems.org folks.
Signed-off-by: Sasha Khapyorsky <sashak@alsa-project.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Untested, but this should fix up the bulk of the totally mechanical
issues, and should make the actual detail fixing easier.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] Use CONFIG_GENERIC_TIME and define TOD clock source.
[PATCH] sysrq: irq change build fix.
[S390] irq change build fixes.
[S390] cio: 0 is a valid chpid.
[S390] monwriter buffer limit.
[S390] ap bus poll thread priority.
Fixup broken UML build due to 7d12e780e0
"IRQ: Maintain regs pointer globally rather than passing to IRQ handlers".
Cc: David Howells <dhowells@redhat.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo "Blaisorblade" Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is some confusion about the meaning of 'bufsz' for a sunrpc server.
In some cases it is the largest message that can be sent or received. In
other cases it is the largest 'payload' that can be included in a NFS
message.
In either case, it is not possible for both the request and the reply to be
this large. One of the request or reply may only be one page long, which
fits nicely with NFS.
So we remove 'bufsz' and replace it with two numbers: 'max_payload' and
'max_mesg'. Max_payload is the size that the server requests. It is used
by the server to check the max size allowed on a particular connection:
depending on the protocol a lower limit might be used.
max_mesg is the largest single message that can be sent or received. It is
calculated as the max_payload, rounded up to a multiple of PAGE_SIZE, and
with PAGE_SIZE added to overhead. Only one of the request and reply may be
this size. The other must be at most one page.
Cc: Greg Banks <gnb@sgi.com>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes a bug introduced in 2.6.18.
If a drive is added to a raid1 using older tools (mdadm-1.x or raidtools)
then it will be included in the array without any resync happening.
It has been submitted for 2.6.18.1.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SD cards extend the protocol by allowing the host to query a card how many
blocks were successfully stored on the medium. This allows us to safely write
chunks of blocks at once.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is required for the SWARM GenBus IDE interface to be recognized.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a kerneldoc warning and reorderd the description for is_init().
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add MAINTAINERS entries for new scx200_hrt and pc8736x_gpio drivers, and
take over maintenance of scx200_gpio, authored by Christer Weinigel (which
I've hacked at), who no longer has the hardware.
Also take over hwmon/pc87360, authored by Jean Delvare, who's dropped
maintenance to dedicate more time to hwmon subsystem.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Christer Weinigel <christer@weinigel.se>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Trivial typo fix in the "syntax error if percpu macros are incorrectly
used" patch. I misspelled "identifier" in all places. D'Oh!
Thanks to Dirk Mueller to point this out.
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
annotate, fix the bogus argument of vmap() in it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The recent header cleanup removed PAGE_SIZE from the exported information as
it depends on the configuration.
BTW This has possibly other consequences, as the core dump code is using
PAGE_SIZE directly, which may need fixing as well.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
avoid unnecessary xchg() use in set_mb()
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jump to the correct exit label after exception
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Provide a tickadj compatibility define for archs still using it.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a way for a no_page() handler to request a retry of the faulting
instruction. It goes back to userland on page faults and just tries again
in get_user_pages(). I added a cond_resched() in the loop in that later
case.
The problem I have with signal and spufs is an actual bug affecting apps and I
don't see other ways of fixing it.
In addition, we are having issues with infiniband and 64k pages (related to
the way the hypervisor deals with some HV cards) that will require us to muck
around with the MMU from within the IB driver's no_page() (it's a pSeries
specific driver) and return to the caller the same way using NOPAGE_REFAULT.
And to add to this, the graphics folks have been following a new approach of
memory management that involves transparently swapping objects between video
ram and main meory. To do that, they need installing PTEs from a no_page()
handler as well and that also requires returning with NOPAGE_REFAULT.
(For the later, they are currently using io_remap_pfn_range to install one PTE
from no_page() which is a bit racy, we need to add a check for the PTE having
already been installed afer taking the lock, but that's ok, they are only at
the proof-of-concept stage. I'll send a patch adding a "clean" function to do
that, we can use that from spufs too and get rid of the sparsemem hacks we do
to create struct page for SPEs. Basically, that provides a generic solution
for being able to have no_page() map hardware devices, which is something that
I think sound driver folks have been asking for some time too).
All of these things depend on having the NOPAGE_REFAULT exit path from
no_page() handlers.
Signed-off-by: Benjamin Herrenchmidt <benh@kernel.crashing.org>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reduce the NUMA text size of mm/slab.o a little on x86 by using a local
variable to store the result of numa_node_id().
text data bss dec hex filename
16858 2584 16 19458 4c02 mm/slab.o (before)
16804 2584 16 19404 4bcc mm/slab.o (after)
[akpm@osdl.org: use better names]
[pbadari@us.ibm.com: fix that]
Cc: Christoph Lameter <christoph@lameter.com>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a more correct fix for the way the ohci hcd was referencing pt_regs
in the unlink paths.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Tim and Ananiev report that the recent WARN_ON_ONCE changes cause increased
cache misses with the tbench workload. Apparently due to the access to the
newly-added static variable.
Rearrange the code so that we don't touch that variable unless the warning is
going to trigger.
Also rework the logic so that the static variable starts out at zero, so we
can move it into bss.
It would seem logical to mark the static variable as __read_mostly too. But
it would be wrong, because that would put it back into the vmlinux image, and
the kernel will never read from this variable in normal operation anyway.
Unless the compiler or hardware go and do some prefetching on us?
For some reason this patch shrinks softirq.o text by 40 bytes.
Cc: Tim Chen <tim.c.chen@intel.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "Ananiev, Leonid I" <leonid.i.ananiev@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Squash this warning:
kernel/audit.c: In function 'kauditd_thread':
kernel/audit.c:367: warning: no return statement in function returning non-void
We might as test kthread_should_stop(), although it's not very pointful at
present.
The code which starts this thread looks racy - the kernel could start multiple
threads.
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix too slow clock by using CONFIG_GENERIC_TIME and adding a
clock source for the s390 time-of-day clock. As added benefit
we get rid of the s390 specific definition of do_gettimeofday
and do_settimeofday.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
drivers/char/sysrq.c: In function `sysrq_handle_crashdump':
drivers/char/sysrq.c:98: warning: implicit declaration of function `get_irq_regs'
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In order to determine chpid validity, we need to check whether the
corresponding path is specified in the pim.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make max_bufs a global (per linux guest) limit.
Signed-off-by: Melissa Howland <melissah@us.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The ap bus is supposed to have a low priority. We must use 19 instead
of -20, which is just the opposite.
Signed-off-by: Christian Borntraeger <cborntra@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix up some of the buildbreaks from the irq handler changes.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.infradead.org/~dhowells/irq-2.6:
IRQ: Maintain regs pointer globally rather than passing to IRQ handlers
IRQ: Typedef the IRQ handler function type
IRQ: Typedef the IRQ flow handler function type
The UDF filesystem can't be mounted in read-write mode any more,
because of forgotten braces.
Signed-off-by: Peter Osterlund <petero2@telia.com>
[ Duh! ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6:
[PATCH] i386: fix rwsem build bug on CONFIG_M386=y
[PATCH] x86-64: Annotate interrupt frame backlink in interrupt handlers
[PATCH] x86-64: Fix FPU corruption
[PATCH] x86: Terminate the kernel stacks for the unwinder
[PATCH] i386: Fix PCI BIOS config space access
[PATCH] x86-64: Calgary IOMMU: print PCI bus numbers in hex
[PATCH] x86-64: Calgary IOMMU: Update Jon's contact info
[PATCH] x86-64: Calgary IOMMU: Fix off by one when calculating register space location
[PATCH] x86-64: Calgary IOMMU: deobfuscate calgary_init
[PATCH] i386: Update defconfig
[PATCH] x86-64: Update defconfig
[ Manually skipped commits that incorrectly ignored AC in kernel space.
The alignment fault is defined to only happen for CPL3 anyway - Linus ]
commit 0181944fe6 adds a
'extended_error_logging' global variable to qla2xxx which is defined by
qla4xxx too.
Trying to build both drivers results in the following error:
LD drivers/scsi/built-in.o
drivers/scsi/qla4xxx/built-in.o: In function `qla4xxx_slave_configure':
drivers/scsi/qla4xxx/ql4_os.c:1433: multiple definition of `extended_error_logging'
drivers/scsi/qla2xxx/built-in.o:drivers/scsi/qla2xxx/qla_os.c:2166:
first defined here
make[2]: *** [drivers/scsi/built-in.o] Error 1
make[1]: *** [drivers/scsi] Error 2
make: *** [drivers] Error 2
The following patch simply adds a qla2_ (qla4_ respectively) prefix to
the variable name.
Signed-off-by: Frederik Deweerdt <frederik.deweerdt@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CONFIG_M386 turns on spinlock-based generic rwsems - which surprises the
semaphore.S rwsem stubs. Tested both with and without CONFIG_M386.
Reported-by: Klaus Knopper <knopper@knopper.net>
Triaged-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andi Kleen <ak@suse.de>
This reverts an earlier patch that was found to cause FPU
state corruption. I think the corruption happens because
unlazy_fpu() can cause FPU exceptions and when it happens
after the current switch some processing would affect
the state in the wrong process.
Thanks to Douglas Crosher and Tom Hughes for testing.
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Always make sure RIP/EIP is 0 in the registers stored on the top
of the stack of a kernel thread. This makes sure the unwinder code
won't try a fallback but knows the stack has ended.
AK: this patch is a bit mysterious. in theory they should be terminated
anyways, but it seems to fix at least one crash. Anyways double termination
probably doesn't hurt.
Signed-off-by: Andi Kleen <ak@suse.de>
Make the references to the bus number in hex instead of decimal, as
that is the way that lspci prints out the bus numbers.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Also add copyright for work done after leaving IBM.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
The purpose of the code being modified is to determine the location
of the calgary chip address space. This is done by a magical formula
of FE0MB-8MB*OneBasedChassisNumber+1MB*(RioNodeId-ChassisBase) to
find the offset where BIOS puts it. In this formula,
OneBasedChassisNumber corresponds to the NUMA node, and rionodeid is
always 2 or 3 depending on which chip in the system it is. The
problem was that we had an off by one error that caused us to account
some busses to the wrong chip and thus give them the wrong address
space.
Fixes RH bugzilla #203971.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-bu: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
calgary_init's for loop does not correspond to the actual device being
checked, which makes its upperbound check for array overflow useless.
Changing this to a do-while loop is the correct way of doing this.
There should be no possibility of spinning forever in this loop, as
pci_get_device states that it will go through all iterations, then
return NULL (thus breaking the loop).
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
Typedef the IRQ handler function type.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1356d1e5fd256997e3d3dce0777ab787d0515c7a commit)
