msleep(USB_RESUME_TIMEOUT) must be done when the controller drives
the resume. This is true after HPRT0_RES is written.
Moreover, restore the delay after controller power is up.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This part 2 pull request contains only the patches
which make sure everybody on linux uses the same
resume timeout value.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=RqsO
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-testing
Felipe writes:
usb: generic resume timeout for v4.1
This part 2 pull request contains only the patches
which make sure everybody on linux uses the same
resume timeout value.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix using the bare number to set the 'bDescriptorType' field of the Hub
Descriptor while the value is #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As usual, a big pile of commits. This time a total
of 111 non-merge commits.
Other than the usual set of cleanups and non-critical
fixes, we have some interesting work for AM335x's MUSB
babble recovery. Now that takes a lot less time and we
don't have to Reset MUSB all the time.
The printer gadget has been converted to configfs interface
and the atmel udc has learned suspend/resume with wakeup.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=U+M2
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.1 merge window
As usual, a big pile of commits. This time a total
of 111 non-merge commits.
Other than the usual set of cleanups and non-critical
fixes, we have some interesting work for AM335x's MUSB
babble recovery. Now that takes a lot less time and we
don't have to Reset MUSB all the time.
The printer gadget has been converted to configfs interface
and the atmel udc has learned suspend/resume with wakeup.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The dwc2-pci driver should be compiled as a module when configured to
do so. If the dwc2-pci is configured as a module but actually
built-in, it can cause build errors due to the fact that the
generic-phy will be allowed to compile as a module causing undefined
references.
Reported-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When the HCD is disconnected, the DMA transfers still in-flight were cleaned-up
but the count of available DMA channels (e.g. available_host_channels) was not
reset.
The pool of DMA channels can be depleted when doing unclean
disconnection of USB peripherals, and reaches the point where no
transfer was possible until the next reboot/reload of the driver.
Tested by putting a programmable USB mux on the port and randomly
plugging/unpluging a USB HUB with USB mass-storage key, USB-audio and
USB-ethernet dongle connected to its downstream ports, and also doing the
disconnection early while the devices are still enumerating to get more URBs
in-flight.
After the patch, the devices are still enumerating after thousands of cycles,
while the port was totally dead before.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The dwc2-pci driver requires the generic PHY. This fixes undefined
reference issues when it is not selected.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If device is configured to work only in HOST or DEVICE mode, there is
no point in initializing both subdrivers. This patch also fixes
resource leakage if host subdriver fails to initialize.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The pci driver now registers a platform driver, like in dwc3, and lets
its probe function do all the initialization. This allows it to
account for changes to the platform driver that were not added to the
pci driver. Also future changes to the probe function don't have to be
duplicated. This also has the effect of adding device and DRD mode to
the pci driver. Tested on the Synopsys HAPS PCIe platform.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When dwc2 controller detects a disconnect interrupt,
dwc2_hcd_disconnect() should be called immediately to do clean-up
jobs and set port_connect_status_change flag to notify usb hub
driver disconnect status.
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Removed FIXME from usb/dwc3/dwc3-pci.c by moving definition of
PCI_VENDOR_ID_SYNOPSYS shared with usb/dwc2 to linux/pci_ids.h.
Signed-off-by: Joseph Kogut <joseph.kogut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Here's the big pull request for Gadgets and PHYs. It's
a total of 217 non-merge commits with pretty much everything
being touched.
The most important bits are a ton of new documentation for
almost all usb gadget functions, a new isp1760 UDC driver,
several improvements to the old net2280 UDC driver, and
some minor tracepoint improvements to dwc3.
Other than that, a big list of minor cleanups, smaller bugfixes
and new features all over the place.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=bGMq
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.20 merge window
Here's the big pull request for Gadgets and PHYs. It's
a total of 217 non-merge commits with pretty much everything
being touched.
The most important bits are a ton of new documentation for
almost all usb gadget functions, a new isp1760 UDC driver,
several improvements to the old net2280 UDC driver, and
some minor tracepoint improvements to dwc3.
Other than that, a big list of minor cleanups, smaller bugfixes
and new features all over the place.
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to the DWC2 datasheet, the HWCFG1 register stores
the configured endpoint directions for endpoints 0-15 in bit positions
0-31.
==========================
Endpoint Direction (EpDir)
This 32-bit field uses two bits per endpoint to determine the endpoint
direction.
Endpoint
Bits [31:30]: Endpoint 15 direction
Bits [29:28]: Endpoint 14 direction
....
Bits [3:2]: Endpoint 1 direction
Bits[1:0]: Endpoint 0 direction (always BIDIR)
==========================
The DWC2 driver is currently interpreting the contents of the register
as directions for endpoints 1-15 which leads to an error in determining
the configured endpoint directions in the core because the first 2 bits
determine the direction of endpoint 0 and not 1.
This is based on testing/next branch in Felipe's git.
Signed-off-by: Roshan Pius <rpius@chromium.org>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It is currently possible to configure the dwc2 driver as built-in
when host mode or dual-role is enabled, but the USB core is
a loadable module. This leads to a link failure:
drivers/built-in.o: In function `_dwc2_hcd_start':
:(.text+0x84538): undefined reference to `usb_hcd_resume_root_hub'
drivers/built-in.o: In function `_dwc2_hcd_urb_dequeue':
:(.text+0x84aa0): undefined reference to `usb_hcd_check_unlink_urb'
:(.text+0x84e4c): undefined reference to `usb_hcd_unlink_urb_from_ep'
:(.text+0x84e74): undefined reference to `usb_hcd_giveback_urb'
drivers/built-in.o: In function `dwc2_assign_and_init_hc':
:(.text+0x86b98): undefined reference to `usb_hcd_unmap_urb_for_dma'
drivers/built-in.o: In function `_dwc2_hcd_urb_enqueue':
:(.text+0x8717c): undefined reference to `usb_hcd_link_urb_to_ep'
:(.text+0x872f4): undefined reference to `usb_hcd_unlink_urb_from_ep'
drivers/built-in.o: In function `dwc2_host_complete':
:(.text+0x875d4): undefined reference to `usb_hcd_unlink_urb_from_ep'
:(.text+0x87600): undefined reference to `usb_hcd_giveback_urb'
drivers/built-in.o: In function `dwc2_hcd_init':
:(.text+0x87ba8): undefined reference to `usb_disabled'
:(.text+0x87d38): undefined reference to `usb_create_hcd'
:(.text+0x88094): undefined reference to `usb_add_hcd'
:(.text+0x880dc): undefined reference to `usb_put_hcd'
drivers/built-in.o: In function `dwc2_hcd_remove':
:(.text+0x8821c): undefined reference to `usb_remove_hcd'
:(.text+0x8823c): undefined reference to `usb_put_hcd'
drivers/built-in.o: In function `dwc2_hc_handle_tt_clear.isra.10':
:(.text+0x88e2c): undefined reference to `usb_hub_clear_tt_buffer'
drivers/built-in.o: In function `dwc2_hcd_qtd_add':
:(.text+0x8b554): undefined reference to `usb_calc_bus_time'
To fix the problem, this patch changes the dependencies so that
dwc2 host mode can only be enabled if either the USB core is
built-in or both USB and dwc2 are modules.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
USB reset interrupt is no more used to reset the controller.
Thus, reset the controller in pullup callback as described by
Synopsys programming guide. Otherwise enumeration sometimes
fails when usb configuration is switched without physical
disconnection.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Defines are more readable and searchable than constants.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
hsotg->phyif is set in dwc2_gadget_init according to phy interface
width. Use it for configuration instead of hardcoded value.
Moreover, set USB turnaround time according to phy width.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Print debug message according to zlp direction. Always saying
"Sending" is misleading.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pullup doesn't need to be enabled during usb reset since it is
already enabled. This leads to shorter chirp-k duration if done
during usb reset.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add a flag to request physical reset of the controller when
s3c_hsotg_core_init_disconnected is called.
During the usb reset, controller must not be fully reconfigured and
resetted. Else this leads to shorter chirp-k duration during
enumeration.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When using DMA, dwc2 requires buffers to be 4 bytes aligned. Use
bounce buffers if they are not.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove dead code as well.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
s3c_hsotg_process_req_feature comments was not correct
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Handle SET_FEATURE TEST_MODE request sent by the host.
Slightly rework FEATURE request handling to allow parsing
other request types than Endpoint.
Also add a debugfs to change test mode value from user space.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When clearing HALT on an endpoint, req->complete of in progress
requests must be called with locks off. New request should only be
started if there is not already a pending request on the endpoint.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When a remote wakeup happens during bus_suspend, hcd needs to resume
its root hub.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix using the bare number to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare number to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This reverts commit 0cf884e819.
Even after applying the follow-on patch at
https://patchwork.kernel.org/patch/5325111
there are still problems with device connect on the Altera SOCFPGA
platform at least. One possible fix would be to add a whitelist
to enable suspend/resume on platforms where it does work correctly.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes the following problem: data transmission in direction
IN break unless the GSNPSID register access is done with spinlock held.
This issue occurs at least in Exynos4412 SoC, probably in many SoC's
from Exynos familly.
The problem is described here:
https://lkml.org/lkml/2014/12/22/185
And there is linux mailing list discussion:
https://lkml.org/lkml/2015/1/14/17
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If usb bus is reset without a physical disconnection, all endpoints
will remain open. Call s3c_hsotg_disconnect() from reset handler to
report a disconnect to gadget framework. hsotg->connected is checked
in s3c_hsotg_disconnect() before processing disconnect.
In some cases, USBRst is seen before EnumDone and after it as well.
So move setting of hsotg->connected to set-address to avoid reporting
extra disconnection in this case.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When booting with id pin grounded, dwc2 default to host mode.
Thus, force device mode prior initializing gadget part.
Else fifo init will fail since fifo values are not correct
in host mode.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This callback informs the driver about the total amount of current it
is allowed to draw. Share this information with the phy so that
current limits can be set for charging for example.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Gadget must be informed about disconnection when pullup is
removed.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
After all endpoints are disabled, fifo_map should have reached 0.
Its a bug if if didn't, so warn about it and reset it to 0 so that
driver can continue using all the fifos.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When selecting different alt setting, s3c_hsotg_ep_enable can be
called with fifo already allocated. Allocate fifo again only if
required and after deallocating the previous fifo.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Current algorithm picks the first fifo which is equal to or greater
than the required size. This can result in bigger fifos assigned to
endpoints with smaller maxps. Change the algorithm to pick the
smallest fifo which is greater than or equal to the required size.
Moreover, only use signed variables when required.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This flag is set before sending the zlp. So use present tense instead
of the past tense.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Enable phy driver to report vbus session. This allows us to remove
D+ pullup when vbus is not present.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Can't stay in the loop forever. Break it after timeout.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The warning is probably good but it has false positives in both dma and non-dma
cases. So its not very helpful in either.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to programming guide, zero length packet should be
programmed on its own and should not be counted in DIEPTSIZ.PktCnt
with other packets.
For ep0, this is the zlp for DATA IN stage (if required) and not for
the STATUS stage.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Manage ep0 state in software to add handling of status OUT stage.
Just toggling hsotg->setup in s3c_hsotg_handle_outdone leaves it in
wrong state in 2-stage control transfers.
Moreover, ensure that for setup-packet s3c_hsotg_handle_outdone is
called either from SetupDone or OutDone but not both. Dwc2 ip v3.00a
generates both SetupDone and OutDone on setup packets.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
kill_all_requests() can flush the fifo. Call it after disabling the
endpoint.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When matching tx fifo to endpoint, consider all fifos instead of
hard limiting to 8
Moreover, print error in case no fifo could be found.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
< 15 check doesn't show debug information for endpoint 15.
It is possible to have less than 15 endpoints so use limit
provided by hardware configuration.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
These members are only occupying space.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
