The PCI core uses a fixed 50ms timeout when waiting for VPD accesses to
complete. When an access does not complete within this period, a warning
is logged and an error returned to the caller.
While this default timeout is valid for most hardware, some devices can
experience longer access delays under certain circumstances. For example,
one of the IBM CXL Flash devices can take up to ~120ms in a worst-case
scenario. These types of devices can benefit from an extended timeout.
To support devices with a longer access delay, increase the timeout in
pci_vpd_wait() to 125ms. The PCI specification is silent with respect to
VPD delays, therefore there is no concern for violating a threshold.
Tested-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Bart reported a problem wіth an out of bounds access in the low-level IRQ
affinity code, which we root caused to the qla2xxx driver assigning all its
MSI-X vectors to the pre and post vectors, and not having any left for the
actually spread IRQs.
Fix this issue by not asking for affinity assignment when there are no
vectors to assign left.
Fixes: 402723ad5c ("PCI/MSI: Provide pci_alloc_irq_vectors_affinity()")
Link: https://lkml.kernel.org/r/1485359225.3093.3.camel@sandisk.com
Reported-by: Bart Van Assche <bart.vanassche@sandisk.com>
Tested-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The only way to call iproc_pcie_pltfm_probe() is to match an entry in
iproc_pcie_of_match_table[], so match cannot be NULL.
Use of_device_get_match_data() to retrieve the pcie->type. No functional
change intended.
Based-on-suggestion-from: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The only way to call ls_pcie_probe() is to match an entry in
ls_pcie_of_match[], so match cannot be NULL.
Use of_device_get_match_data() to retrieve the drvdata pointer. No
functional change intended.
Based-on-suggestion-from: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This is a DT-only driver, so the only way to call rcar_pcie_probe() is to
match an entry in rcar_pcie_of_match[], so of_id cannot be NULL.
Furthermore, of_id->data can only be NULL if an rcar_pcie_of_match[] entry
has a NULL .data member. That's a driver defect, and we don't want to
return -EINVAL, which is easy to ignore. We'd rather take the NULL pointer
dereference so we notice the problem and fix it.
Use of_device_get_match_data() to retrieve the hw_init_fn pointer. No
functional change intended.
Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
The "port" variable was allocated with devm_kzalloc() so if we free it with
kfree() it will be freed twice. Also I changed it to propogate the error
from devm_ioremap_resource() instead of returning -ENOMEM.
Fixes: c5d4603961 ("PCI: Add MCFG quirks for X-Gene host controller")
Also-posted-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Tanmay Inamdar <tinamdar@apm.com>
This causes CPU hangs when the system is reset by the watchdog, as the GPRs
aren't cleared, but the clocks are back to disabled state.
If the bootloader uses PCIe, it must take care to bring it down into a safe
state, before passing control to the Linux kernel. This is the only way to
get a properly operating system at all times and circumstances.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_lock is an IRQ-safe spinlock that protects all accesses to PCI
configuration space (see PCI_OP_READ() and PCI_OP_WRITE() in pci/access.c).
The pci_cfg_access_unlock() path acquires pci_lock, then p->pi_lock (inside
wake_up_all()). According to lockdep, there is a possible path involving
snbep_uncore_pci_read_counter() that could acquire them in the reverse
order: acquiring p->pi_lock, then pci_lock, which could result in a
deadlock. Lockdep details are in the bugzilla below.
Avoid the possible deadlock by dropping pci_lock before waking up any
config access waiters.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=192901
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When CONFIG_PM_SLEEP is disabled, we get harmless build warnings:
host/pcie-rockchip.c:1267:12: error: 'rockchip_pcie_resume_noirq' defined but not used [-Werror=unused-function]
host/pcie-rockchip.c:1240:12: error: 'rockchip_pcie_suspend_noirq' defined but not used [-Werror=unused-function]
Marking both functions as __maybe_unused avoids the warning without the
need for #ifdef around them.
Fixes: 013dd3d5e1 ("PCI: rockchip: Add system PM support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Use readl_poll_timeout() instead of open-coding it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI core will write to the bridge window config multiple times while
they are enabled. This can lead to mbus failures like this:
mvebu_mbus: cannot add window '4:e8', conflicts with another window
mvebu-pcie mbus:pex@e0000000: Could not create MBus window at [mem 0xe0000000-0xe00fffff]: -22
For me this is happening during a hotplug cycle. The PCI core is not
changing the values, just writing them twice while active.
The patch addresses the general case of any change to an active window, but
not atomically. The code is slightly refactored so io and mem can share
more of the window logic.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Rename the simple pointer name as "ep" instead of "exynos_pcie". After
applying this patch, it can save the 10 characthers within one line.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Intel 200-series chipsets have the same errata as 100-series: the ACS
capability doesn't follow the PCIe spec, the capability and control
registers are dwords rather than words. Add PCIe root port device IDs to
existing quirk.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In a struct pcie_link_state, link->root points to the pcie_link_state of
the root of the PCIe hierarchy. For the topmost link, this points to
itself (link->root = link). For others, we copy the pointer from the
parent (link->root = link->parent->root).
Previously we recognized that Root Ports originated PCIe hierarchies, but
we treated PCI/PCI-X to PCIe Bridges as being in the middle of the
hierarchy, and when we tried to copy the pointer from link->parent->root,
there was no parent, and we dereferenced a NULL pointer:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000090
IP: [<ffffffff9e424350>] pcie_aspm_init_link_state+0x170/0x820
Recognize that PCI/PCI-X to PCIe Bridges originate PCIe hierarchies just
like Root Ports do, so link->root for these devices should also point to
itself.
Fixes: 51ebfc92b7 ("PCI: Enumerate switches below PCI-to-PCIe bridges")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=193411
Link: https://bugzilla.opensuse.org/show_bug.cgi?id=1022181
Tested-by: lists@ssl-mail.com
Tested-by: Jayachandran C. <jnair@caviumnetworks.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v4.2+
The conversion to the new hotplug state machine introduced a regression
where a successful hotplug registration would be treated as an error,
effectively disabling the MSI driver forever.
Fix it by doing the proper check on the return value.
Fixes: 9c248f8896 ("PCI/xgene-msi: Convert to hotplug state machine")
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Duc Dang <dhdang@apm.com>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: stable@vger.kernel.org
Since we need to change the implementation, stop exposing internals.
Provide kref_read() to read the current reference count; typically
used for debug messages.
Kills two anti-patterns:
atomic_read(&kref->refcount)
kref->refcount.counter
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
All multi-MSI allocations are now done through pci_irq_alloc_vectors(), so
remove the old pci_enable_msi_range() and pci_enable_msi_exact()
interfaces.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The pci-thunder-pem driver was initially developed for cn88xx SoCs. The
cn81xx and cn83xx members of the same family of SoCs have a slightly
different configuration of interrupt resources in the PEM hardware, which
prevents the INTA legacy interrupt source from functioning with the current
driver.
There are two fixes required:
1) Don't fixup the PME interrupt on the newer SoCs as it already has the
proper value.
2) Report MSI-X Capability Table Size of 2 for the newer SoCs, so the core
MSI-X code doesn't inadvertently clobber the INTA machinery that happens to
reside immediately following the table.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Rockchip's RC produces a 100MHz reference clock but there are two methods
for the PHY to generate it:
(1) Use the system PLL to generate a 100MHz clock. The PHY will relock
it, filter signal noise, and output the reference clock. ASPM L0s
works correctly, but circuit noise issues make it difficult to pass
the TX compatibility test.
(2) Share the SoC's 24MHZ crystal oscillator with the PHY and force the
PHY's PLL to generate 100MHz internally. In this case, exit from
ASPM L0s sometimes fails due to a design error in the RC receiver
circuit. Even if we use extended-synch, the PHY sometimes fails to
relock the bits from FTS, which will hang the system.
We want the flexibility to use both clocking methods, so add a DT property,
"aspm-no-l0s". If that's present, disable L0s to avoid the issues with
case (2).
[bhelgaas: changelog]
Reported-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
Fix kernel-doc warnings in pci/msi.c:
..//drivers/pci/msi.c:623: warning: No description found for parameter 'affd'
..//drivers/pci/msi.c:623: warning: Excess function parameter 'affinity' description in 'msi_capability_init'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When a PCI card is not connected, the following messages are seen on mx6:
imx6q-pcie 1ffc000.pcie: phy link never came up
imx6q-pcie 1ffc000.pcie: Link never came up
The first one comes from the pcie-designware.c core file, so remove
the redundant one from the imx6 driver.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
ibm_apci_table_attr is not modified after being initialized by
ibm_acpiphp_init(). It is passed as an argument to the functions
sysfs_{remove/create}_bin_file(), but both the arguments are const.
Add __ro_after_init to its declaration.
[bhelgaas: changelog]
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
R-Car PCIe does not support hotplug so it is appropriate to treat the
absence of a PCIe card as an -ENODEV error.
Signed-off-by: Harunobu Kurokawa <harunobu.kurokawa.dn@renesas.com>
[simon: updated changelog]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add system PM support for Rockchip's RC. For pre S3, the EP is configured
into D3 state which guarantees the link state should be in L1. So we could
send PME_Turn_Off message to the EP and wait for its ACK to make the link
state into L2 or L3 without the aux-supply. This could help save more
power which I think should be very important for mobile devices.
As note that there is a 5s timeout for RC to wait for the PMA_ACK after
sending PME_Turn_Off. Technically it should depend on the hierarchy of
devices but seems PCIe core framework doesn't handle the L2/3 for S3 at
all. So that means we should presume to set a default value for PME_ACK.
From the bug report[1], we could find a statement that Microsoft Windows
versions typically wait for 5 seconds. So we are prone to take 5s for this
timeout here.
[1] https://lists.launchpad.net/kernel-packages/msg123315.html
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
A PCI-to-PCIe bridge (a "reverse bridge") has a PCI or PCI-X primary
interface and a PCI Express secondary interface. The PCIe interface is a
Downstream Port that originates a Link. See the "PCI Express to PCI/PCI-X
Bridge Specification", rev 1.0, sections 1.2 and A.6.
The bug report below involves a PCI-to-PCIe bridge and a PCIe switch below
the bridge:
00:1e.0 Intel 82801 PCI Bridge to [bus 01-0a]
01:00.0 Pericom PI7C9X111SL PCIe-to-PCI Reversible Bridge to [bus 02-0a]
02:00.0 Pericom Device 8608 [PCIe Upstream Port] to [bus 03-0a]
03:01.0 Pericom Device 8608 [PCIe Downstream Port] to [bus 0a]
01:00.0 is configured as a PCI-to-PCIe bridge (despite the name printed by
lspci). As we traverse a PCIe hierarchy, device connections alternate
between PCIe Links and internal Switch logic. Previously we did not
recognize that 01:00.0 had a secondary link, so we thought the 02:00.0
Upstream Port *did* have a secondary link. In fact, it's the other way
around: 01:00.0 has a secondary link, and 02:00.0 has internal Switch logic
on its secondary side.
When we thought 02:00.0 had a secondary link, the pci_scan_slot() ->
only_one_child() path assumed 02:00.0 could have only one child, so 03:00.0
was the only possible downstream device. But 03:00.0 doesn't exist, so we
didn't look for any other devices on bus 03.
Booting with "pci=pcie_scan_all" is a workaround, but we don't want users
to have to do that.
Recognize that PCI-to-PCIe bridges originate links on their secondary
interfaces.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=189361
Fixes: d0751b98df ("PCI: Add dev->has_secondary_link to track downstream PCIe links")
Tested-by: Blake Moore <blake.moore@men.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v4.2+
Previously we checked for iATU unroll support by reading PCIE_ATU_VIEWPORT
even on platforms, e.g., Keystone, that do not have ATU ports. This can
cause bad behavior such as asynchronous external aborts:
OF: PCI: MEM 0x60000000..0x6fffffff -> 0x60000000
Unhandled fault: asynchronous external abort (0x1211) at 0x00000000
pgd = c0003000
[00000000] *pgd=80000800004003, *pmd=00000000
Internal error: : 1211 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.9.0-00009-g6ff59d2-dirty #7
Hardware name: Keystone
task: eb878000 task.stack: eb866000
PC is at dw_pcie_setup_rc+0x24/0x380
LR is at ks_pcie_host_init+0x10/0x170
Move the dw_pcie_iatu_unroll_enabled() check so we only call it on
platforms that do not use the ATU. These platforms supply their own
->rd_other_conf() and ->wr_other_conf() methods.
[bhelgaas: changelog]
Fixes: a0601a4705 ("PCI: designware: Add iATU Unroll feature")
Fixes: 416379f9eb ("PCI: designware: Check for iATU unroll support after initializing host")
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-By: Joao Pinto <jpinto@synopsys.com>
CC: stable@vger.kernel.org # v4.9+
Previously we didn't check the type of device before trying to apply Type 1
(PCI-X) or Type 2 (PCIe) Setting Records from _HPX.
We don't support PCI-X Setting Records, so this was harmless, but the
warning was useless.
We do support PCIe Setting Records, and we didn't check whether a device
was PCIe before applying settings. I don't think anything bad happened on
non-PCIe devices because pcie_capability_clear_and_set_word(),
pcie_cap_has_lnkctl(), etc., would fail before doing any harm. But it's
ugly to depend on those internals.
Check the device type before attempting to apply Type 1 and Type 2 Setting
Records (Type 0 records are applicable to PCI, PCI-X, and PCIe devices).
A side benefit is that this prevents useless "not supported" warnings when
a BIOS supplies a Type 1 (PCI-X) Setting Record and we try to apply it to
every single device:
pci 0000:00:00.0: PCI-X settings not supported
After this patch, we'll get the warning only when a BIOS supplies a Type 1
record and we have a PCI-X device to which it should be applied.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=187731
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Remove res_to_dev_res() debug message. This is printed from a lookup
function. If the message is important, it should be printed from the
caller with more context.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Highlights include:
- Support for the kexec_file_load() syscall, which is a prereq for secure and
trusted boot.
- Prevent kernel execution of userspace on P9 Radix (similar to SMEP/PXN).
- Sort the exception tables at build time, to save time at boot, and store
them as relative offsets to save space in the kernel image & memory.
- Allow building the kernel with thin archives, which should allow us to build
an allyesconfig once some other fixes land.
- Build fixes to allow us to correctly rebuild when changing the kernel endian
from big to little or vice versa.
- Plumbing so that we can avoid doing a full mm TLB flush on P9 Radix.
- Initial stack protector support (-fstack-protector).
- Support for dumping the radix (aka. Linux) and hash page tables via debugfs.
- Fix an oops in cxl coredump generation when cxl_get_fd() is used.
- Freescale updates from Scott: "Highlights include 8xx hugepage support,
qbman fixes/cleanup, device tree updates, and some misc cleanup."
- Many and varied fixes and minor enhancements as always.
Thanks to:
Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V, Anshuman Khandual,
Anton Blanchard, Balbir Singh, Bartlomiej Zolnierkiewicz, Christophe Jaillet,
Christophe Leroy, Denis Kirjanov, Elimar Riesebieter, Frederic Barrat,
Gautham R. Shenoy, Geliang Tang, Geoff Levand, Jack Miller, Johan Hovold,
Lars-Peter Clausen, Libin, Madhavan Srinivasan, Michael Neuling, Nathan
Fontenot, Naveen N. Rao, Nicholas Piggin, Pan Xinhui, Peter Senna Tschudin,
Rashmica Gupta, Rui Teng, Russell Currey, Scott Wood, Simon Guo, Suraj
Jitindar Singh, Thiago Jung Bauermann, Tobias Klauser, Vaibhav Jain.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xOzf
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights include:
- Support for the kexec_file_load() syscall, which is a prereq for
secure and trusted boot.
- Prevent kernel execution of userspace on P9 Radix (similar to
SMEP/PXN).
- Sort the exception tables at build time, to save time at boot, and
store them as relative offsets to save space in the kernel image &
memory.
- Allow building the kernel with thin archives, which should allow us
to build an allyesconfig once some other fixes land.
- Build fixes to allow us to correctly rebuild when changing the
kernel endian from big to little or vice versa.
- Plumbing so that we can avoid doing a full mm TLB flush on P9
Radix.
- Initial stack protector support (-fstack-protector).
- Support for dumping the radix (aka. Linux) and hash page tables via
debugfs.
- Fix an oops in cxl coredump generation when cxl_get_fd() is used.
- Freescale updates from Scott: "Highlights include 8xx hugepage
support, qbman fixes/cleanup, device tree updates, and some misc
cleanup."
- Many and varied fixes and minor enhancements as always.
Thanks to:
Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V, Anshuman
Khandual, Anton Blanchard, Balbir Singh, Bartlomiej Zolnierkiewicz,
Christophe Jaillet, Christophe Leroy, Denis Kirjanov, Elimar
Riesebieter, Frederic Barrat, Gautham R. Shenoy, Geliang Tang, Geoff
Levand, Jack Miller, Johan Hovold, Lars-Peter Clausen, Libin,
Madhavan Srinivasan, Michael Neuling, Nathan Fontenot, Naveen N.
Rao, Nicholas Piggin, Pan Xinhui, Peter Senna Tschudin, Rashmica
Gupta, Rui Teng, Russell Currey, Scott Wood, Simon Guo, Suraj
Jitindar Singh, Thiago Jung Bauermann, Tobias Klauser, Vaibhav Jain"
[ And thanks to Michael, who took time off from a new baby to get this
pull request done. - Linus ]
* tag 'powerpc-4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (174 commits)
powerpc/fsl/dts: add FMan node for t1042d4rdb
powerpc/fsl/dts: add sg_2500_aqr105_phy4 alias on t1024rdb
powerpc/fsl/dts: add QMan and BMan nodes on t1024
powerpc/fsl/dts: add QMan and BMan nodes on t1023
soc/fsl/qman: test: use DEFINE_SPINLOCK()
powerpc/fsl-lbc: use DEFINE_SPINLOCK()
powerpc/8xx: Implement support of hugepages
powerpc: get hugetlbpage handling more generic
powerpc: port 64 bits pgtable_cache to 32 bits
powerpc/boot: Request no dynamic linker for boot wrapper
soc/fsl/bman: Use resource_size instead of computation
soc/fsl/qe: use builtin_platform_driver
powerpc/fsl_pmc: use builtin_platform_driver
powerpc/83xx/suspend: use builtin_platform_driver
powerpc/ftrace: Fix the comments for ftrace_modify_code
powerpc/perf: macros for power9 format encoding
powerpc/perf: power9 raw event format encoding
powerpc/perf: update attribute_group data structure
powerpc/perf: factor out the event format field
powerpc/mm/iommu, vfio/spapr: Put pages on VFIO container shutdown
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ut0k
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"PCI changes:
- add support for PCI on ARM64 boxes with ACPI. We already had this
for theoretical spec-compliant hardware; now we're adding quirks
for the actual hardware (Cavium, HiSilicon, Qualcomm, X-Gene)
- add runtime PM support for hotplug ports
- enable runtime suspend for Intel UHCI that uses platform-specific
wakeup signaling
- add yet another host bridge registration interface. We hope this is
extensible enough to subsume the others
- expose device revision in sysfs for DRM
- to avoid device conflicts, make sure any VF BAR updates are done
before enabling the VF
- avoid unnecessary link retrains for ASPM
- allow INTx masking on Mellanox devices that support it
- allow access to non-standard VPD for Chelsio devices
- update Broadcom iProc support for PAXB v2, PAXC v2, inbound DMA,
etc
- update Rockchip support for max-link-speed
- add NVIDIA Tegra210 support
- add Layerscape LS1046a support
- update R-Car compatibility strings
- add Qualcomm MSM8996 support
- remove some uninformative bootup messages"
* tag 'pci-v4.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (115 commits)
PCI: Enable access to non-standard VPD for Chelsio devices (cxgb3)
PCI: Expand "VPD access disabled" quirk message
PCI: pciehp: Remove loading message
PCI: hotplug: Remove hotplug core message
PCI: Remove service driver load/unload messages
PCI/AER: Log AER IRQ when claiming Root Port
PCI/AER: Log errors with PCI device, not PCIe service device
PCI/AER: Remove unused version macros
PCI/PME: Log PME IRQ when claiming Root Port
PCI/PME: Drop unused support for PMEs from Root Complex Event Collectors
PCI: Move config space size macros to pci_regs.h
x86/platform/intel-mid: Constify mid_pci_platform_pm
PCI/ASPM: Don't retrain link if ASPM not possible
PCI: iproc: Skip check for legacy IRQ on PAXC buses
PCI: pciehp: Leave power indicator on when enabling already-enabled slot
PCI: pciehp: Prioritize data-link event over presence detect
PCI: rcar: Add gen3 fallback compatibility string for pcie-rcar
PCI: rcar: Use gen2 fallback compatibility last
PCI: rcar-gen2: Use gen2 fallback compatibility last
PCI: rockchip: Move the deassert of pm/aclk/pclk after phy_init()
..
These changes include:
* Support for the ACPI IORT table on ARM systems and patches to
make the ARM-SMMU driver make use of it
* Conversion of the Exynos IOMMU driver to device dependency
links and implementation of runtime pm support based on that
conversion
* Update the Mediatek IOMMU driver to use the new
struct device->iommu_fwspec member
* Implementation of dma_map/unmap_resource in the generic ARM
dma-iommu layer
* A number of smaller fixes and improvements all over the place
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=EYLL
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"These changes include:
- support for the ACPI IORT table on ARM systems and patches to make
the ARM-SMMU driver make use of it
- conversion of the Exynos IOMMU driver to device dependency links
and implementation of runtime pm support based on that conversion
- update the Mediatek IOMMU driver to use the new struct
device->iommu_fwspec member
- implementation of dma_map/unmap_resource in the generic ARM
dma-iommu layer
- a number of smaller fixes and improvements all over the place"
* tag 'iommu-updates-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (44 commits)
ACPI/IORT: Make dma masks set-up IORT specific
iommu/amd: Missing error code in amd_iommu_init_device()
iommu/s390: Drop duplicate header pci.h
ACPI/IORT: Introduce iort_iommu_configure
ACPI/IORT: Add single mapping function
ACPI/IORT: Replace rid map type with type mask
iommu/arm-smmu: Add IORT configuration
iommu/arm-smmu: Split probe functions into DT/generic portions
iommu/arm-smmu-v3: Add IORT configuration
iommu/arm-smmu-v3: Split probe functions into DT/generic portions
ACPI/IORT: Add support for ARM SMMU platform devices creation
ACPI/IORT: Add node match function
ACPI: Implement acpi_dma_configure
iommu/arm-smmu-v3: Convert struct device of_node to fwnode usage
iommu/arm-smmu: Convert struct device of_node to fwnode usage
iommu: Make of_iommu_set/get_ops() DT agnostic
ACPI/IORT: Add support for IOMMU fwnode registration
ACPI/IORT: Introduce linker section for IORT entries probing
ACPI: Add FWNODE_ACPI_STATIC fwnode type
iommu/arm-smmu: Set SMTNMB_TLBEN in ACR to enable caching of bypass entries
...
Pull s390 updates from Martin Schwidefsky:
"The main bulk of the s390 patches for the 4.10 merge window:
- Add support for the contiguous memory allocator.
- The recovery for I/O errors in the dasd device driver is improved,
the driver will now remove channel paths that are not working
properly.
- Additional fields are added to /proc/sysinfo, the extended
partition name and the partition UUID.
- New naming for PCI devices with system defined UIDs.
- The last few remaining alloc_bootmem calls are converted to
memblock.
- The thread_info structure is stripped down and moved to the
task_struct. The only field left in thread_info is the flags field.
- Rework of the arch topology code to fix a fake numa issue.
- Refactoring of the atomic primitives and add a new preempt_count
implementation.
- Clocksource steering for the STP sync check offsets.
- The s390 specific headers are changed to make them usable with
CLANG.
- Bug fixes and cleanup"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (70 commits)
s390/cpumf: Use configuration level indication for sampling data
s390: provide memmove implementation
s390: cleanup arch/s390/kernel Makefile
s390: fix initrd corruptions with gcov/kcov instrumented kernels
s390: exclude early C code from gcov profiling
s390/dasd: channel path aware error recovery
s390/dasd: extend dasd path handling
s390: remove unused labels from entry.S
s390/vmlogrdr: fix IUCV buffer allocation
s390/crypto: unlock on error in prng_tdes_read()
s390/sysinfo: show partition extended name and UUID if available
s390/numa: pin all possible cpus to nodes early
s390/numa: establish cpu to node mapping early
s390/topology: use cpu_topology array instead of per cpu variable
s390/smp: initialize cpu_present_mask in setup_arch
s390/topology: always use s390 specific sched_domain_topology_level
s390/smp: use smp_get_base_cpu() helper function
s390/numa: always use logical cpu and core ids
s390: Remove VLAIS in ptff() and clear_table()
s390: fix machine check panic stack switch
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJYT5HMAAoJELDendYovxMvhNQH/1g/3ahM4JKN8Z0SbjKBEdQm
yj2xOj6cE3l6wMSUblKjZD2DLLhpmcHT/E97Xro/lZQEfQJoMXXWWDFowMU/P1LA
mJxb7Fzq5Wr+6eGSAlIQB270MrpNi/luf+CWHMwVA3V7R3KRXwonOdGQSkISIzCd
tgIydEA3a9r2+HgeIBpZFZ4GcSrJQU75krMyl2tjD1C+jeYVd+zdoj2OnDsZQDZQ
hDWApMpNbpSBAn7JtSSdXWSTBsGH0lUECebeYPhPQ2sX2P6Y8+UCGwA7i6FFdbTa
agXfVSdRz8dCe3k19VcKDAw6nK9BTTMnEeEHmkmygIh6wuHPP44CzigTXIbJoXI=
=zjfm
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.10-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from Juergen Gross:
"Xen features and fixes for 4.10
These are some fixes, a move of some arm related headers to share them
between arm and arm64 and a series introducing a helper to make code
more readable.
The most notable change is David stepping down as maintainer of the
Xen hypervisor interface. This results in me sending you the pull
requests for Xen related code from now on"
* tag 'for-linus-4.10-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (29 commits)
xen/balloon: Only mark a page as managed when it is released
xenbus: fix deadlock on writes to /proc/xen/xenbus
xen/scsifront: don't request a slot on the ring until request is ready
xen/x86: Increase xen_e820_map to E820_X_MAX possible entries
x86: Make E820_X_MAX unconditionally larger than E820MAX
xen/pci: Bubble up error and fix description.
xen: xenbus: set error code on failure
xen: set error code on failures
arm/xen: Use alloc_percpu rather than __alloc_percpu
arm/arm64: xen: Move shared architecture headers to include/xen/arm
xen/events: use xen_vcpu_id mapping for EVTCHNOP_status
xen/gntdev: Use VM_MIXEDMAP instead of VM_IO to avoid NUMA balancing
xen-scsifront: Add a missing call to kfree
MAINTAINERS: update XEN HYPERVISOR INTERFACE
xenfs: Use proc_create_mount_point() to create /proc/xen
xen-platform: use builtin_pci_driver
xen-netback: fix error handling output
xen: make use of xenbus_read_unsigned() in xenbus
xen: make use of xenbus_read_unsigned() in xen-pciback
xen: make use of xenbus_read_unsigned() in xen-fbfront
...
Pull irq updates from Thomas Gleixner:
"The irq department provides:
- a major update to the auto affinity management code, which is used
by multi-queue devices
- move of the microblaze irq chip driver into the common driver code
so it can be shared between microblaze, powerpc and MIPS
- a series of updates to the ARM GICV3 interrupt controller
- the usual pile of fixes and small improvements all over the place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (25 commits)
powerpc/virtex: Use generic xilinx irqchip driver
irqchip/xilinx: Try to fall back if xlnx,kind-of-intr not provided
irqchip/xilinx: Add support for parent intc
irqchip/xilinx: Rename get_irq to xintc_get_irq
irqchip/xilinx: Restructure and use jump label api
irqchip/xilinx: Clean up print messages
microblaze/irqchip: Move intc driver to irqchip
ARM: virt: Select ARM_GIC_V3_ITS
ARM: gic-v3-its: Add 32bit support to GICv3 ITS
irqchip/gic-v3-its: Specialise readq and writeq accesses
irqchip/gic-v3-its: Specialise flush_dcache operation
irqchip/gic-v3-its: Narrow down Entry Size when used as a divider
irqchip/gic-v3-its: Change unsigned types for AArch32 compatibility
irqchip/gic-v3: Use nops macro for Cavium ThunderX erratum 23154
irqchip/gic-v3: Convert arm64 GIC accessors to {read,write}_sysreg_s
genirq/msi: Drop artificial PCI dependency
irqchip/bcm7038-l1: Implement irq_cpu_offline() callback
genirq/affinity: Use default affinity mask for reserved vectors
genirq/affinity: Take reserved vectors into account when spreading irqs
PCI: Remove the irq_affinity mask from struct pci_dev
...
Pull smp hotplug updates from Thomas Gleixner:
"This is the final round of converting the notifier mess to the state
machine. The removal of the notifiers and the related infrastructure
will happen around rc1, as there are conversions outstanding in other
trees.
The whole exercise removed about 2000 lines of code in total and in
course of the conversion several dozen bugs got fixed. The new
mechanism allows to test almost every hotplug step standalone, so
usage sites can exercise all transitions extensively.
There is more room for improvement, like integrating all the
pointlessly different architecture mechanisms of synchronizing,
setting cpus online etc into the core code"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (60 commits)
tracing/rb: Init the CPU mask on allocation
soc/fsl/qbman: Convert to hotplug state machine
soc/fsl/qbman: Convert to hotplug state machine
zram: Convert to hotplug state machine
KVM/PPC/Book3S HV: Convert to hotplug state machine
arm64/cpuinfo: Convert to hotplug state machine
arm64/cpuinfo: Make hotplug notifier symmetric
mm/compaction: Convert to hotplug state machine
iommu/vt-d: Convert to hotplug state machine
mm/zswap: Convert pool to hotplug state machine
mm/zswap: Convert dst-mem to hotplug state machine
mm/zsmalloc: Convert to hotplug state machine
mm/vmstat: Convert to hotplug state machine
mm/vmstat: Avoid on each online CPU loops
mm/vmstat: Drop get_online_cpus() from init_cpu_node_state/vmstat_cpu_dead()
tracing/rb: Convert to hotplug state machine
oprofile/nmi timer: Convert to hotplug state machine
net/iucv: Use explicit clean up labels in iucv_init()
x86/pci/amd-bus: Convert to hotplug state machine
x86/oprofile/nmi: Convert to hotplug state machine
...
* pci/host-vmd:
PCI: vmd: Fix suspend handlers defined-but-not-used warning
PCI: vmd: Use SRCU as a local RCU to prevent delaying global RCU
PCI: vmd: Remove unnecessary pci_set_drvdata()
* pci/host-rockchip:
PCI: rockchip: Move the deassert of pm/aclk/pclk after phy_init()
PCI: rockchip: Split out rockchip_cfg_atu()
PCI: rockchip: Clean up bit definitions for PCIE_RC_CONFIG_LCS
PCI: rockchip: Correct the use of FTS mask
PCI: rockchip: Remove the pointer to L1 substate cap
PCI: rockchip: Specify the link capability
PCI: rockchip: Fix negotiated lanes calculation
PCI: rockchip: Add Kconfig COMPILE_TEST
PCI: rockchip: Mark RC as common clock architecture
PCI: rockchip: Provide captured slot power limit and scale
PCI: rockchip: Add three new resets as required properties
PCI: Don't attempt to claim shadow copies of ROM
PCI: designware: Check for iATU unroll support after initializing host
PCI: qcom: Fix pp->dev usage before assignment
PCI: designware-plat: Update author email address
PCI: layerscape: Fix drvdata usage before assignment
PCI: designware-plat: Change maintainer to Jose Abreu
* pci/host-rcar:
PCI: rcar: Add gen3 fallback compatibility string for pcie-rcar
PCI: rcar: Use gen2 fallback compatibility last
PCI: rcar-gen2: Use gen2 fallback compatibility last
* pci/host-hv:
PCI: hv: Allocate physically contiguous hypercall params buffer
PCI: hv: Delete the device earlier from hbus->children for hot-remove
PCI: hv: Fix hv_pci_remove() for hot-remove
PCI: hv: Use the correct buffer size in new_pcichild_device()
PCI: hv: Make unnecessarily global IRQ masking functions static
* pci/host-altera:
PCI: altera: Remove redundant error message in altera_pcie_parse_dt()
PCI: altera: Use builtin_platform_driver() to simplify the code
* pci/virtualization:
PCI: Add comments about ROM BAR updating
PCI: Decouple IORESOURCE_ROM_ENABLE and PCI_ROM_ADDRESS_ENABLE
PCI: Remove pci_resource_bar() and pci_iov_resource_bar()
PCI: Don't update VF BARs while VF memory space is enabled
PCI: Separate VF BAR updates from standard BAR updates
PCI: Update BARs using property bits appropriate for type
PCI: Ignore BAR updates on virtual functions
PCI: Do any VF BAR updates before enabling the BARs
PCI: Support INTx masking on ConnectX-4 with firmware x.14.1100+
PCI: Convert Mellanox broken INTx quirks to be for listed devices only
PCI: Convert broken INTx masking quirks from HEADER to FINAL
net/mlx4_core: Use device ID defines
PCI: Add Mellanox device IDs
* pci/pm:
x86/platform/intel-mid: Constify mid_pci_platform_pm
PCI: pciehp: Add runtime PM support for PCIe hotplug ports
ACPI / hotplug / PCI: Make device_is_managed_by_native_pciehp() public
ACPI / hotplug / PCI: Use cached copy of PCI_EXP_SLTCAP_HPC bit
PCI: Unfold conditions to block runtime PM on PCIe ports
PCI: Consolidate conditions to allow runtime PM on PCIe ports
PCI: Activate runtime PM on a PCIe port only if it can suspend
PCI: Speed up algorithm in pci_bridge_d3_update()
PCI: Autosense device removal in pci_bridge_d3_update()
PCI: Don't acquire ref on parent in pci_bridge_d3_update()
USB: UHCI: report non-PME wakeup signalling for Intel hardware
PCI: Check for PME in targeted sleep state
There is at least one Chelsio 10Gb card which uses VPD area to store some
non-standard blocks (example below). However pci_vpd_size() returns the
length of the first block only assuming that there can be only one VPD "End
Tag".
Since 4e1a635552 ("vfio/pci: Use kernel VPD access functions"), VFIO
blocks access beyond that offset, which prevents the guest "cxgb3" driver
from probing the device. The host system does not have this problem as its
driver accesses the config space directly without pci_read_vpd().
Add a quirk to override the VPD size to a bigger value. The maximum size
is taken from EEPROMSIZE in drivers/net/ethernet/chelsio/cxgb3/common.h.
We do not read the tag as the cxgb3 driver does as the driver supports
writing to EEPROM/VPD and when it writes, it only checks for 8192 bytes
boundary. The quirk is registered for all devices supported by the cxgb3
driver.
This adds a quirk to the PCI layer (not to the cxgb3 driver) as the cxgb3
driver itself accesses VPD directly and the problem only exists with the
vfio-pci driver (when cxgb3 is not running on the host and may not be even
loaded) which blocks accesses beyond the first block of VPD data. However
vfio-pci itself does not have quirks mechanism so we add it to PCI.
This is the controller:
Ethernet controller [0200]: Chelsio Communications Inc T310 10GbE Single Port Adapter [1425:0030]
This is what I parsed from its VPD:
===
b'\x82*\x0010 Gigabit Ethernet-SR PCI Express Adapter\x90J\x00EC\x07D76809 FN\x0746K'
0000 Large item 42 bytes; name 0x2 Identifier String
b'10 Gigabit Ethernet-SR PCI Express Adapter'
002d Large item 74 bytes; name 0x10
#00 [EC] len=7: b'D76809 '
#0a [FN] len=7: b'46K7897'
#14 [PN] len=7: b'46K7897'
#1e [MN] len=4: b'1037'
#25 [FC] len=4: b'5769'
#2c [SN] len=12: b'YL102035603V'
#3b [NA] len=12: b'00145E992ED1'
007a Small item 1 bytes; name 0xf End Tag
0c00 Large item 16 bytes; name 0x2 Identifier String
b'S310E-SR-X '
0c13 Large item 234 bytes; name 0x10
#00 [PN] len=16: b'TBD '
#13 [EC] len=16: b'110107730D2 '
#26 [SN] len=16: b'97YL102035603V '
#39 [NA] len=12: b'00145E992ED1'
#48 [V0] len=6: b'175000'
#51 [V1] len=6: b'266666'
#5a [V2] len=6: b'266666'
#63 [V3] len=6: b'2000 '
#6c [V4] len=2: b'1 '
#71 [V5] len=6: b'c2 '
#7a [V6] len=6: b'0 '
#83 [V7] len=2: b'1 '
#88 [V8] len=2: b'0 '
#8d [V9] len=2: b'0 '
#92 [VA] len=2: b'0 '
#97 [RV] len=80: b's\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00'...
0d00 Large item 252 bytes; name 0x11
#00 [VC] len=16: b'122310_1222 dp '
#13 [VD] len=16: b'610-0001-00 H1\x00\x00'
#26 [VE] len=16: b'122310_1353 fp '
#39 [VF] len=16: b'610-0001-00 H1\x00\x00'
#4c [RW] len=173: b'\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00'...
0dff Small item 0 bytes; name 0xf End Tag
10f3 Large item 13315 bytes; name 0x62
!!! unknown item name 98: b'\xd0\x03\x00@`\x0c\x08\x00\x00\x00\x00\x00\x00\x00\x00\x00'
===
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
It's not very enlightening to see
pci 0000:07:00.0: [Firmware Bug]: VPD access disabled
in the dmesg log because there's no clue about what the firmware bug is.
Expand the message to explain why we're disabling VPD.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Remove the "PCI Express Hot Plug Controller Driver" version message. I
don't think it contains any useful information. Remove unused #defines
and move the author information to a comment.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Remove the "PCI Hot Plug PCI Core" version message. I don't think it
contains any useful information. Remove unused #defines and move the
author information to a comment.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Remove the "service driver %s loaded" and unloaded messages. All service
drivers already log something in their probe functions, where they can log
more useful details.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
All other AER-related log messages use the PCI device, e.g.,
"pci 0000:00:1c.0", not the PCIe service device, e.g.,
"aer 0000:00:1c.0:pcie02".
Change the probe error messages to match the rest and include a little
context.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Remove the unused DRIVER_VERSION, DRIVER_AUTHOR, and DRIVER_DESC macros.
The author information is already included in a comment above.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We already log a "Signaling PME" whenever the PME service driver claims a
Root Port. In fact, we also log the same message for every device in the
hierarchy below the Root Port.
Log the "Signaling PME" once (only for the Root Port, since we can
trivially find out which devices are below the Root Port), and include the
IRQ number in the message to help connect the dots with /proc/interrupts.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since we register pcie_pme_driver only for PCI_EXP_TYPE_ROOT_PORT, the PME
driver never claims Root Complex Event Collectors.
Remove unused code related to Root Complex Event Collectors.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Move PCI configuration space size macros (PCI_CFG_SPACE_SIZE and
PCI_CFG_SPACE_EXP_SIZE) from drivers/pci/pci.h to
include/uapi/linux/pci_regs.h so they can be used by more drivers and
eliminate duplicate definitions.
[bhelgaas: Expand comment to include PCI-X details]
Signed-off-by: Wang Sheng-Hui <shhuiw@foxmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This struct never needs to be modified. The size of pci-mid.o ELF
sections changes thusly:
-.data 56
+.data 0
-.rodata 32
+.rodata 88
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Some (defective) PCIe devices are not able to reliably do link retraining.
Check to see if ASPM is possible between link partners before configuring
common clocking, and doing the resulting link retraining. If ASPM is not
possible, there is no reason to risk losing access to a device due to an
unnecessary link retraining.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PAXC and PAXCv2 buses do not support legacy IRQs so there is no reason to
even try and map them. Without a change like this, one cannot create VFs
on Nitro ports since legacy interrupts are checked as part of the PCI
device creation process. Testing on PAXC hardware showed that VFs are
properly created with only the change to not set pcie->map_irq, but just to
be safe the change in iproc_pcie_setup() will ensure that pdev_fixup_irq()
will not panic.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
If an error occurs when enabling a slot, pciehp_power_thread() turns off
the power indicator. But if the only error is that the slot was already
enabled, we should leave the power indicator on.
Return success if called to enable an already-enabled slot.
This is in the same spirit of the special handling for EEXISTS when
pciehp_configure_device() determines the slot devices already exist.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
If Slot Status indicates changes in both Data Link Layer Status and
Presence Detect, prioritize the Link status change.
When both events are observed, pciehp currently relies on the Slot Status
Presence Detect State (PDS) to agree with the Link Status Data Link Layer
Active status. The Presence Detect State, however, may be set to 1 through
out-of-band presence detect even if the link is down, which creates
conflicting events.
Since the Link Status accurately reflects the reachability of the
downstream bus, the Link Status event should take precedence over a
Presence Detect event. Skip checking the PDC status if we handled a link
event in the same handler.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Add fallback compatibility string for the R-Car Gen 3 family. This is in
keeping with the both the existing fallback compatibility string for the
R-Car Gen 2 family and the fallback scheme being adopted wherever
appropriate for drivers for Renesas SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Improve readability by listing fallback compatibility strings after the
more-specific compatibility strings they provide a fallback for.
This does not affect run-time behaviour as it is the order in the DTB that
determines which compatibility string is used.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Improve readability by listing fallback compatibility strings after the
more-specific compatibility strings they provide a fallback for.
This does not affect run-time behaviour as it is the order in the DTB that
determines which compatibility string is used.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move deassert of pm/aclk/pclk after phy_init() as we want to optimize the
logic of reset control and reuse rockchip_pcie_init_port() later which
should fully follow the cold boot procedure of ROM code.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Split out a new function, rockchip_cfg_atu(), in order to re-configure the
ATU when missing these information after wakeup from S3.
[bhelgaas: add "dev" temporary, return 0 when known]
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
PCIE_RC_CONFIG_LCS contains control and status bits specific to the PCIe
link. The layout for this register looks the same as the existing
PCI_EXP_LNKCTL and PCI_EXP_LNKSTA. So let's reuse them.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We're trying to mask out bits[23:8] while retaining [32:24, 7:0], but we're
doing the inverse. That doesn't have too much effect, since we're setting
all the [23:8] bits to 1, and the other bits are only relevant for modes
we're currently not using. But we should get this right.
Fixes: ca19890840 ("PCI: rockchip: Fix wrong transmitted FTS count")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Per the errata of TRM, the RC can't support L1 substate, so remove the L1
substate cap as well as operation for PCIE_RC_CONFIG_L1_SUBSTATE_CTRL2.
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
rk3399 supports PCIe 2.x link speeds marginally at best, and on some
boards, the link won't train at 5 GT/s at all. Rather than sacrifice 500ms
waiting for training that will never happen, let's use the helper function,
of_pci_get_max_link_speed(), to get the max link speed from DT and specify
link capability.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The calculation of negotiated lanes is wrong: it should be shifted by
PCIE_CORE_PL_CONF_LANE_SHIFT, but it is shifted by
PCIE_CORE_PL_CONF_LANE_MASK instead. Let's fix it.
Fixes: e77f847df5 ("PCI: rockchip: Add Rockchip PCIe controller support")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Allow selection of the Rockchip driver for compile testing, even if we
aren't building for ARCH_ROCKCHIP.
[bhelgaas: changelog]
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The default value of common clock configuration is zero indicating
Rockchip's RC is using asynchronous clock architecture but actually we are
using common clock. This will confuse some EP drivers if they need some
different settings referring to this value.
Set the Common Clock Configuration bit in the Link Control Register.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If vpcie3v3 is available, we could provide these information via RC's
configure register to make EP able to know the power limit.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add Makefile comments to explain the Kconfig and build strategy for ARM64
drivers that work around not-quite-ECAM issues. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use builtin_platform_driver() helper to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Fix the following warnings:
drivers/pci/host/vmd.c:731:12: warning: ‘vmd_suspend’ defined but not used [-Wunused-function]
static int vmd_suspend(struct device *dev)
^
drivers/pci/host/vmd.c:739:12: warning: ‘vmd_resume’ defined but not used [-Wunused-function]
static int vmd_resume(struct device *dev)
^
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Reviewed-by: Keith Busch <keith.busch@intel.com>
SRCU lets synchronize_srcu() depend on VMD-local RCU primitives, preventing
long delays from locking up RCU in other systems. VMD performs a
synchronize when removing a device, but will hit all IRQ lists if the
device uses all VMD vectors. This patch will not help VMD's RCU
synchronization, but will isolate the read side delays to the VMD
subsystem. Additionally, the use of SRCU in VMD's ISR will keep it
isolated from any other RCU waiters in the rest of the system.
Tested using concurrent FIO and NVMe resets:
[global]
rw=read
bs=4k
direct=1
ioengine=libaio
iodepth=32
norandommap
timeout=300
runtime=1000000000
[nvme0]
cpus_allowed=0-63
numjobs=8
filename=/dev/nvme0n1
[nvme1]
cpus_allowed=0-63
numjobs=8
filename=/dev/nvme1n1
while (true) do
for i in /sys/class/nvme/nvme*; do
echo "Resetting ${i##*/}"
echo 1 > $i/reset_controller;
sleep 5
done;
done
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
The Tegra PCI host controller driver no longer relies on any of the 32-bit
ARM glue for PCI, so it can be enabled on 64-bit configurations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
The PCIe host controller found on Tegra X1 is very similar to its
predecessor on Tegra K1. A bug was introduced in the new revision that
is worked around by always enabling the performance counter, otherwise
accesses to configuration space will block for a number of seconds.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Tegra210's PCIe controller has a bug that requires the PCA (performance
counter) feature to be enabled. If this isn't done, accesses to device
configuration space will hang the chip for tens of seconds. Implement the
workaround.
Based on commit 514e19138af2 ("pci: tegra: implement PCA enable
workaround") from U-Boot by Stephen Warren <swarren@nvidia.com>.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Tegra is one of the remaining platforms that still use the traditional
pci_common_init_dev() interface for probing PCI host bridges.
This demonstrates how to convert it to the pci_register_host interface I
just added in a previous patch. This leads to a more linear probe sequence
that can handle errors better because we avoid callbacks into the driver,
and it makes the driver architecture independent.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Allow PCI host bridge drivers to use the new host bridge interfaces to
register their host bridge.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Provide a way to allocate driver-specific data along with a PCI host bridge
structure. The bridge's ->private field points to this data.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Make the existing pci_host_bridge structure a proper device that is usable
by PCI host drivers in a more standard way. In addition to the existing
pci_scan_bus(), pci_scan_root_bus(), pci_scan_root_bus_msi(), and
pci_create_root_bus() interfaces, this unfortunately means having to add
yet another interface doing basically the same thing, and add some extra
code in the initial step.
However, this time it's more likely to be extensible enough that we won't
have to do another one again in the future, and we should be able to reduce
code much more as a result.
The main idea is to pull the allocation of 'struct pci_host_bridge' out of
the registration, and let individual host drivers and architecture code
fill the members before calling the registration function.
There are a number of things we can do based on this:
* Use a single memory allocation for the driver-specific structure
and the generic PCI host bridge
* consolidate the contents of driver-specific structures by moving
them into pci_host_bridge
* Add a consistent interface for removing a PCI host bridge again
when unloading a host driver module
* Replace the architecture specific __weak pcibios_*() functions with
callbacks in a pci_host_bridge device
* Move common boilerplate code from host drivers into the generic
function, based on contents of the structure
* Extend pci_host_bridge with additional members when needed without
having to add arguments to pci_scan_*().
* Move members of struct pci_bus into pci_host_bridge to avoid
having lots of identical copies.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
PCIe controllers in X-Gene SoCs are not ECAM compliant: software needs to
configure additional controller's register to address device at
bus:dev:function.
Add a quirk to discover controller MMIO register space and configure
controller registers to select and address the target secondary device.
The quirk will only be applied for X-Gene PCIe MCFG table with
OEM revison 1, 2, 3 or 4 (PCIe controller v1 and v2 on X-Gene SoCs).
Tested-by: Jon Masters <jcm@redhat.com>
Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
ThunderX pass1.x requires to emulate the EA headers for on-chip devices
hence it has to use custom pci_thunder_ecam_ops for accessing PCI config
space (pci-thunder-ecam.c). Add new entries to MCFG quirk array where it
can be applied while probing ACPI based PCI host controller.
ThunderX pass1.x is using the same way for accessing off-chip devices
(so-called PEM) as silicon pass-2.x so we need to add PEM quirk entries
too.
Quirk is considered for ThunderX silicon pass1.x only which is identified
via MCFG revision 2.
ThunderX pass 1.x requires the following accessors:
NUMA node 0 PCI segments 0- 3: pci_thunder_ecam_ops (MCFG quirk)
NUMA node 0 PCI segments 4- 9: thunder_pem_ecam_ops (MCFG quirk)
NUMA node 1 PCI segments 10-13: pci_thunder_ecam_ops (MCFG quirk)
NUMA node 1 PCI segments 14-19: thunder_pem_ecam_ops (MCFG quirk)
[bhelgaas: change Makefile/ifdefs so quirk doesn't depend on
CONFIG_PCI_HOST_THUNDER_ECAM]
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
ThunderX PCIe controller to off-chip devices (so-called PEM) is not fully
compliant with ECAM standard. It uses non-standard configuration space
accessors (see thunder_pem_ecam_ops) and custom configuration space
granulation (see bus_shift = 24). In order to access configuration space
and probe PEM as ACPI-based PCI host controller we need to add MCFG quirk
infrastructure. This involves:
1. A new thunder_pem_acpi_init() init function to locate PEM-specific
register ranges using ACPI.
2. Export PEM thunder_pem_ecam_ops structure so it is visible to MCFG quirk
code.
3. New quirk entries for each PEM segment. Each contains platform IDs,
mentioned thunder_pem_ecam_ops and CFG resources.
Quirk is considered for ThunderX silicon pass2.x only which is identified
via MCFG revision 1.
ThunderX pass 2.x requires the following accessors:
NUMA Node 0 PCI segments 0- 3: pci_generic_ecam_ops (ECAM-compliant)
NUMA Node 0 PCI segments 4- 9: thunder_pem_ecam_ops (MCFG quirk)
NUMA Node 1 PCI segments 10-13: pci_generic_ecam_ops (ECAM-compliant)
NUMA Node 1 PCI segments 14-19: thunder_pem_ecam_ops (MCFG quirk)
[bhelgaas: adapt to use acpi_get_rc_resources(), update Makefile/ifdefs so
quirk doesn't depend on CONFIG_PCI_HOST_THUNDER_PEM]
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Pull the register resource lookup out of thunder_pem_init() so we can
easily add a corresponding lookup using ACPI. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCIe controller in Hip05/Hip06/Hip07 SoCs is not completely
ECAM-compliant. It is non-ECAM only for the RC bus config space; for any
other bus underneath the root bus it does support ECAM access.
Add specific quirks for PCI config space accessors. This involves:
1. New initialization call hisi_pcie_init() to obtain RC base
addresses from PNP0C02 at the root of the ACPI namespace (under \_SB).
2. New entry in common quirk array.
[bhelgaas: move to pcie-hisi.c and change Makefile/ifdefs so quirk doesn't
depend on CONFIG_PCI_HISI]
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The Qualcomm Technologies QDF2432 SoC does not support accesses smaller
than 32 bits to the PCI configuration space. Register the appropriate
quirk.
[bhelgaas: add QCOM_ECAM32 macro, ifdef for ACPI and PCI_QUIRKS]
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The acpi_get_rc_resources() is used to get the RC register address that can
not be described in MCFG. It takes the _HID & segment to look for and
outputs the RC address resource. Use PNP0C02 devices to describe such RC
address resource. Use _UID to match segment to tell which root bus the
PNP0C02 resource belongs to.
[bhelgaas: add dev argument, wrap in #ifdef CONFIG_PCI_QUIRKS]
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_update_resource() updates a hardware BAR so its address matches the
kernel's struct resource UNLESS it's a disabled ROM BAR. We only update
those when we enable the ROM.
It's not obvious from the code why ROM BARs should be handled specially.
Apparently there are Matrox devices with defective ROM BARs that read as
zero when disabled. That means that if pci_enable_rom() reads the disabled
BAR, sets PCI_ROM_ADDRESS_ENABLE (without re-inserting the address), and
writes it back, it would enable the ROM at address zero.
Add comments and references to explain why we can't make the code look more
rational.
The code changes are from 755528c860 ("Ignore disabled ROM resources at
setup") and 8085ce084c ("[PATCH] Fix PCI ROM mapping").
Link: https://lkml.org/lkml/2005/8/30/138
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Remove the assumption that IORESOURCE_ROM_ENABLE == PCI_ROM_ADDRESS_ENABLE.
PCI_ROM_ADDRESS_ENABLE is the ROM enable bit defined by the PCI spec, so if
we're reading or writing a BAR register value, that's what we should use.
IORESOURCE_ROM_ENABLE is a corresponding bit in struct resource flags.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
pci_std_update_resource() only deals with standard BARs, so we don't have
to worry about the complications of VF BARs in an SR-IOV capability.
Compute the BAR address inline and remove pci_resource_bar(). That makes
pci_iov_resource_bar() unused, so remove that as well.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
If we update a VF BAR while it's enabled, there are two potential problems:
1) Any driver that's using the VF has a cached BAR value that is stale
after the update, and
2) We can't update 64-bit BARs atomically, so the intermediate state
(new lower dword with old upper dword) may conflict with another
device, and an access by a driver unrelated to the VF may cause a bus
error.
Warn about attempts to update VF BARs while they are enabled. This is a
programming error, so use dev_WARN() to get a backtrace.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Previously pci_update_resource() used the same code path for updating
standard BARs and VF BARs in SR-IOV capabilities.
Split the VF BAR update into a new pci_iov_update_resource() internal
interface, which makes it simpler to compute the BAR address (we can get
rid of pci_resource_bar() and pci_iov_resource_bar()).
This patch:
- Renames pci_update_resource() to pci_std_update_resource(),
- Adds pci_iov_update_resource(),
- Makes pci_update_resource() a wrapper that calls the appropriate one,
No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
hv_do_hypercall() assumes that we pass a segment from a physically
contiguous buffer. A buffer allocated on the stack may not work if
CONFIG_VMAP_STACK=y is set.
Use kmalloc() to allocate this buffer.
Reported-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
On DT based systems, the of_dma_configure() API implements DMA
configuration for a given device. On ACPI systems an API equivalent to
of_dma_configure() is missing which implies that it is currently not
possible to set-up DMA operations for devices through the ACPI generic
kernel layer.
This patch fills the gap by introducing acpi_dma_configure/deconfigure()
calls that for now are just wrappers around arch_setup_dma_ops() and
arch_teardown_dma_ops() and also updates ACPI and PCI core code to use
the newly introduced acpi_dma_configure/acpi_dma_deconfigure functions.
Since acpi_dma_configure() is used to configure DMA operations, the
function initializes the dma/coherent_dma masks to sane default values
if the current masks are uninitialized (also to keep the default values
consistent with DT systems) to make sure the device has a complete
default DMA set-up.
The DMA range size passed to arch_setup_dma_ops() is sized according
to the device coherent_dma_mask (starting at address 0x0), mirroring the
DT probing path behaviour when a dma-ranges property is not provided
for the device being probed; this changes the current arch_setup_dma_ops()
call parameters in the ACPI probing case, but since arch_setup_dma_ops()
is a NOP on all architectures but ARM/ARM64 this patch does not change
the current kernel behaviour on them.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> [pci]
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Tomasz Nowicki <tn@semihalf.com>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Tomasz Nowicki <tn@semihalf.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Tomasz Nowicki <tn@semihalf.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The BAR property bits (0-3 for memory BARs, 0-1 for I/O BARs) are supposed
to be read-only, but we do save them in res->flags and include them when
updating the BAR.
Mask the I/O property bits with ~PCI_BASE_ADDRESS_IO_MASK (0x3) instead of
PCI_REGION_FLAG_MASK (0xf) to make it obvious that we can't corrupt bits
2-3 of I/O addresses.
Use PCI_ROM_ADDRESS_MASK for ROM BARs. This means we'll only check the top
21 bits (instead of the 28 bits we used to check) of a ROM BAR to see if
the update was successful.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
VF BARs are read-only zero, so updating VF BARs will not have any effect.
See the SR-IOV spec r1.1, sec 3.4.1.11.
We already ignore these updates because of 70675e0b6a ("PCI: Don't try to
restore VF BARs"); this merely restructures it slightly to make it easier
to split updates for standard and SR-IOV BARs.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Previously we enabled VFs and enable their memory space before calling
pcibios_sriov_enable(). But pcibios_sriov_enable() may update the VF BARs:
for example, on PPC PowerNV we may change them to manage the association of
VFs to PEs.
Because 64-bit BARs cannot be updated atomically, it's unsafe to update
them while they're enabled. The half-updated state may conflict with other
devices in the system.
Call pcibios_sriov_enable() before enabling the VFs so any BAR updates
happen while the VF BARs are disabled.
[bhelgaas: changelog]
Tested-by: Carol Soto <clsoto@us.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In the code to handle PAXB v2 based MSI steering, the logic aligns the MSI
register address to the size of supported inbound mapping range. This is
incorrect since it rounds "up" the starting address to the next aligned
address, but what we want is the starting address to be rounded "down" to
the aligned address.
This patch fixes the issue and allows MSI writes to be properly steered to
the GIC.
Fixes: 4b073155fbd3 ("PCI: iproc: Add support for the next-gen PAXB controller")
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add support for the MSM8996/APQ8096 PCIe controller. MSM8996 supports Gen
1/2, one lane, 3 PCIe root complexes with support for MSI and legacy
interrupts, and it conforms to PCI Express Base 2.1 specification.
Add a post_init callback to qcom_pcie_ops, as the PCIe pipe clocks are only
setup after the phy is powered on. It also adds an ltssm_enable callback
as it is very much different from other supported SoCs in the driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Most error branches following the call to pci_enable_device() contain a
call to pci_disable_device(). Add these calls where they are missing.
This issue was found with Hector.
Signed-off-by: Quentin Lambert <lambert.quentin@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add support for the next generation of the iProc PAXB host controller, used
in Stingray.
Signed-off-by: Oza Oza <oza.oza@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Per PCIe spec r3.0, sec 2.3.1.1, the Read Completion Boundary (RCB)
determines the naturally aligned address boundaries on which a Read Request
may be serviced with multiple Completions:
- For a Root Complex, RCB is 64 bytes or 128 bytes
This value is reported in the Link Control Register
Note: Bridges and Endpoints may implement a corresponding command bit
which may be set by system software to indicate the RCB value for the
Root Complex, allowing the Bridge/Endpoint to optimize its behavior
when the Root Complex’s RCB is 128 bytes.
- For all other system elements, RCB is 128 bytes
Per sec 7.8.7, if a Root Port only supports a 64-byte RCB, the RCB of all
downstream devices must be clear, indicating an RCB of 64 bytes. If the
Root Port supports a 128-byte RCB, we may optionally set the RCB of
downstream devices so they know they can generate larger Completions.
Some BIOSes supply an _HPX that tells us to set RCB, even though the Root
Port doesn't have RCB set, which may lead to Malformed TLP errors if the
Endpoint generates completions larger than the Root Port can handle.
The IBM x3850 X6 with BIOS version -[A8E120CUS-1.30]- 08/22/2016 supplies
such an _HPX and a Mellanox MT27500 ConnectX-3 device fails to initialize:
mlx4_core 0000:41:00.0: command 0xfff timed out (go bit not cleared)
mlx4_core 0000:41:00.0: device is going to be reset
mlx4_core 0000:41:00.0: Failed to obtain HW semaphore, aborting
mlx4_core 0000:41:00.0: Fail to reset HCA
------------[ cut here ]------------
kernel BUG at drivers/net/ethernet/mellanox/mlx4/catas.c:193!
After 6cd33649fa ("PCI: Add pci_configure_device() during enumeration")
and 7a1562d4f2 ("PCI: Apply _HPX Link Control settings to all devices
with a link"), we apply _HPX settings to *all* devices, not just those
hot-added after boot.
Before 7a1562d4f2, we didn't touch the Mellanox RCB, and the device
worked. After 7a1562d4f2, we set its RCB to 128, and it failed.
Set the RCB to 128 iff the Root Port supports a 128-byte RCB. Otherwise,
set RCB to 64 bytes. This effectively ignores what _HPX tells us about
RCB.
Note that this change only affects _HPX handling. If we have no _HPX, this
does nothing with RCB.
[bhelgaas: changelog, clear RCB if not set for Root Port]
Fixes: 6cd33649fa ("PCI: Add pci_configure_device() during enumeration")
Fixes: 7a1562d4f2 ("PCI: Apply _HPX Link Control settings to all devices with a link")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=187781
Tested-by: Frank Danapfel <fdanapfe@redhat.com>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Myron Stowe <myron.stowe@redhat.com>
CC: stable@vger.kernel.org # v3.18+
Export pcie_find_root_port() so we can use it outside of PCIe-AER error
injection.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Mellanox devices were marked as having INTx masking ability broken. As a
result, the VFIO driver fails to start when more than one device function
is passed-through to a VM if both have the same INTx pin.
Prior to Connect-IB, Mellanox devices exposed to the operating system one
PCI function per all ports. Starting from Connect-IB, the devices are
function-per-port. When passing the second function to a VM, VFIO will
fail to start.
Exclude ConnectX-4, ConnectX4-Lx and Connect-IB from the list of Mellanox
devices marked as having broken INTx masking:
- ConnectX-4 and ConnectX4-LX firmware version is checked. If INTx
masking is supported, we unmark the broken INTx masking.
- Connect-IB does not support INTx currently so will not cause any
problem.
[bhelgaas: call pci_disable_device() always, after iounmap()]
Fixes: 11e42532ad ("PCI: Assume all Mellanox devices have broken INTx masking")
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Change Mellanox's broken_intx_masking() quirk from an "all Mellanox
devices" to a quirk for listed devices only.
[bhelgaas: remove #defines, reorder to keep other quirks together]
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Convert all quirk_broken_intx_masking() quirks from HEADER to FINAL.
The quirk sets dev->broken_intx_masking, which is only used by
pci_intx_mask_supported(), which is not needed until after FINAL
quirks have been run.
[bhelgaas: changelog]
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Hardware that supports only 32-bit config writes is not spec-compliant.
For example, if software performs a 16-bit write, we must do a 32-bit read,
merge in the 16 bits we intend to write, followed by a 32-bit write. If
the 16 bits we *don't* intend to write happen to have any RW1C (write-one-
to-clear) bits set, we just inadvertently cleared something we shouldn't
have.
Add a rate-limited warning when we do sub-32 bit config writes. Remove
similar probe-time warnings from some of the affected host bridge drivers.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Enthusiastically-Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com> # rockchip
Acked-by: Thierry Reding <treding@nvidia.com>
Currently the revision isn't available via sysfs/libudev thus if one wants
to know the value one needs to read through the config file, which can be
quite time-consuming because it wakes/powers up the device.
There are at least two userspace components which could make use the new
file: libpciaccess and libdrm. The former wakes up _every_ PCI device,
which can be observed via glxinfo when using Mesa 10.0+ drivers. The
latter, in association with Mesa 13.0, can lead to 2-3 second delays while
starting firefox, thunderbird or chromium.
Link: https://bugs.freedesktop.org/show_bug.cgi?id=98502
Tested-by: Mauro Santos <registo.mailling@gmail.com>
Signed-off-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch
CC: Greg KH <gregkh@linuxfoundation.org>
Linux 4.8 added support for runtime suspending PCIe ports to D3hot with
commit 006d44e49a ("PCI: Add runtime PM support for PCIe ports"), but
excluded hotplug ports. Those are now afforded runtime PM by the present
commit.
Hotplug ports require a few extra considerations:
- The configuration space of the port remains accessible in D3hot, so all
the functions to read or modify the Slot Status and Slot Control
registers need not be modified. Even turning on slot power doesn't seem
to require the port to be in D0, at least the PCIe spec doesn't say so
and I confirmed that by testing with a Thunderbolt controller.
- However D0 is required to access devices on the secondary bus. This
happens in pciehp_check_link_status() and pciehp_configure_device() (both
called from board_added()) and in pciehp_unconfigure_device() (called
from remove_board()), so acquire a runtime PM ref for their invocation.
- The hotplug port stays active as long as it has active children. If all
hotplugged devices below the port runtime suspend, the port is allowed to
runtime suspend as well. Plug and unplug detection continues to work in
D3hot.
- Hotplug interrupts are delivered in-band, so while the hotplug port
itself is allowed to go to D3hot, its parent ports must stay in D0 for
interrupts to come through. Add a corresponding restriction to
pci_dev_check_d3cold().
- Runtime PM may only be allowed if the hotplug port is handled natively by
the OS. On ACPI systems, the port may alternatively be handled by the
firmware and things break if the OS puts the port into D3 behind the
firmware's back: E.g. Thunderbolt hotplug ports on non-Macs are handled
by Intel's firmware in System Management Mode and the firmware is known
to access devices on the port's secondary bus without checking first if
the port is in D0: https://bugzilla.kernel.org/show_bug.cgi?id=53811
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CC: Mika Westerberg <mika.westerberg@linux.intel.com>
We're about to add runtime PM of hotplug ports, but we need to restrict it
to ports that are handled natively by the OS: If they're handled by the
firmware (which is the case for Thunderbolt on non-Macs), things would
break if the OS put the ports into D3hot behind the firmware's back.
To determine if a hotplug port is handled natively, one has to walk up from
the port to the root bridge and check the cached _OSC Control Field for the
value of the "PCI Express Native Hot Plug control" bit. There's already a
function to do that, device_is_managed_by_native_pciehp(), but it's private
to drivers/pci/hotplug/acpiphp_glue.c and only compiled in if
CONFIG_HOTPLUG_PCI_ACPI is enabled.
Make it public and move it to drivers/pci/pci-acpi.c, so that it is
available in the more general CONFIG_ACPI case.
The function contains a check if the device in question is a hotplug port
and returns false if it's not. The caller we're going to add doesn't need
this as it only calls the function if it actually *is* a hotplug port.
Move the check out of the function into the single existing caller.
Rename it to pciehp_is_native() and add some kerneldoc and polish.
No functional change intended.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We cache the PCI_EXP_SLTCAP_HPC bit in pci_dev->is_hotplug_bridge on device
probe, so there's no need to read it again when adding the ACPI hotplug
context.
Here's the call chain to prove that no ordering issue is introduced:
pci_scan_child_bus [drivers/pci/probe.c]
pci_scan_slot
pci_scan_single_device
pci_scan_device
pci_setup_device
set_pcie_hotplug_bridge
[is_hotplug_bridge bit is set here]
pci_scan_bridge
pci_add_new_bus
pci_alloc_child_bus
pcibios_add_bus [arch/(x86|arm64|ia64)/...]
acpi_pci_add_bus [drivers/pci/pci-acpi.c]
acpiphp_enumerate_slots [drivers/pci/hotplug/acpiphp_glue.c]
acpiphp_add_context
device_is_managed_by_native_pciehp
[is_hotplug_bridge bit is queried here]
No functional change intended.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The conditions to block D3 on parent ports are currently condensed into a
single expression in pci_dev_check_d3cold(). Upcoming commits will add
further conditions for hotplug ports, making this expression fairly large
and impenetrable. Unfold the conditions to maintain readability when they
are amended.
No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Mika Westerberg <mika.westerberg@linux.intel.com>
CC: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The conditions to allow runtime PM on PCIe ports are currently spread
across two different files: The condition relating to hotplug ports is
located in portdrv_pci.c whereas all other conditions are located in pci.c.
Consolidate all conditions in a single place in pci.c, thus making it
easier to follow the logic and amend conditions down the road.
Note that the condition relating to hotplug ports is inserted *before* the
condition relating to the "pcie_port_pm=force" command line option, so
runtime PM is not afforded to hotplug ports even if this option is given.
That's exactly how the code behaved up until now. If this is not desired,
the ordering of the conditions can simply be reversed.
No functional change intended.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently pcie_portdrv_probe() activates runtime PM on a PCIe port even
if it will never actually suspend because the BIOS is too old or the
"pcie_port_pm=off" option was specified on the kernel command line.
A few CPU cycles can be saved by not activating runtime PM at all in these
cases, because rpm_idle() and rpm_suspend() will bail out right at the
beginning when calling rpm_check_suspend_allowed(), instead of carrying out
various locking and assignments, invoking rpm_callback(), getting back
-EBUSY and rolling everything back.
The conditions checked in pci_bridge_d3_possible() are all static, they
never change during uptime of the system, hence it's safe to call this to
determine if runtime PM should be activated.
No functional change intended.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After a device has been added, removed or had its D3cold attributes
changed, we recheck whether its parent bridge may runtime suspend to D3hot
with pci_bridge_d3_update().
The most naive algorithm would be to iterate over the bridge's children and
check if any of them are blocking D3.
The function already tries to be a bit smarter than that by first checking
the device that was changed. If this device already blocks D3 on the
bridge, then walking over all the other children can be skipped. A
drawback of this approach is that if the device is *not* blocking D3, it
will be checked a second time by pci_walk_bus(). But that's cheap and is
outweighed by the performance gain of potentially skipping pci_walk_bus()
altogether.
The algorithm can be optimized further by taking into account if D3 is
currently allowed for the bridge, as shown in the following truth table:
(a) remove && bridge_d3: D3 is currently allowed for the bridge and
removing one of its children won't change
that. No action necessary.
(b) remove && !bridge_d3: D3 may now be allowed for the bridge if the
removed child was the only one blocking it.
Check all its siblings to verify that.
(c) !remove && bridge_d3: D3 may now be disallowed but this can only
be caused by the added/changed child, not
any of its siblings. Check only that single
device.
(d) !remove && !bridge_d3: D3 may now be allowed for the bridge if the
changed child was the only one blocking it.
Check all its siblings to verify that.
By checking beforehand if the changed child
is blocking D3, we may be able to skip
checking its siblings.
Currently we do not special-case option (a) and in case of option (c) we
gratuitously call pci_walk_bus(). Speed up the algorithm by adding these
optimizations. Reword the comments a bit in an attempt to improve clarity.
No functional change intended.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The algorithm to update the flag indicating whether a bridge may go to D3
makes a few optimizations based on whether the update was caused by the
removal of a device on the one hand, versus the addition of a device or the
change of its D3cold flags on the other hand.
The information whether the update pertains to a removal is currently
passed in by the caller, but the function may as well determine that itself
by examining the device in question, thereby allowing for a considerable
simplification and reduction of the code.
Out of several options to determine removal, I've chosen the function
device_is_registered() because it's cheap: It merely returns the
dev->kobj.state_in_sysfs flag. That flag is set through device_add() when
the root bus is scanned and cleared through device_remove(). The call to
pci_bridge_d3_update() happens after each of these calls, respectively, so
the ordering is correct.
No functional change intended.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This function is always called with an existing pci_dev struct, which
holds a reference on the pci_bus struct it resides on, which in turn
holds a reference on pci_bus->bridge, which is the pci_dev's parent.
Hence there's no need to acquire an additional ref on the parent.
More specifically, the pci_dev exists until pci_destroy_dev() drops the
final reference on it, so all calls to pci_bridge_d3_update() must be
finished before that. It is arguably the caller's responsibility to ensure
that it doesn't call pci_bridge_d3_update() with a pci_dev that might
suddenly disappear, but in any case the existing callers are all safe:
- The call in pci_destroy_dev() happens before the call to put_device().
- The call in pci_bus_add_device() is synchronized with pci_destroy_dev()
using pci_lock_rescan_remove().
- The calls to pci_d3cold_disable() from the xhci and nouveau drivers
are safe because a ref on the pci_dev is held as long as it's bound to
a driver.
- The calls to pci_d3cold_enable() / pci_d3cold_disable() when modifying
the sysfs "d3cold_allowed" entry are also safe because kernfs_drain()
waits for existing sysfs users to finish before removing the entry,
and pci_destroy_dev() is called way after that.
No functional change intended.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add support for inbound DMA mapping. The range of the inbound mapping is
configured by the optional device tree property 'dma-ranges'.
While inbound mapping is done automatically in the ASIC on most iProc-based
SoCs, newer ASICs (e.g., Stingray) require inbound mapping to be configured
explicitly in software.
[bhelgaas: fold in fixes to avoid 32-bit division in iproc_pcie_ib_write()
and uninitialized return value in iproc_pcie_setup_ib() from Arnd Bergmann
<arnd@arndb.de>]
Signed-off-by: Oza Oza <oza.oza@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Improve the iProc PCIe outbound mapping code by making it more generic and
removing redundant device tree properties 'brcm,pcie-ob-window-size' and
'brcm,pcie-ob-oarr-size'. The driver is still backward compatible to
device tree binaries with the two properties specified.
The driver now automatically configures the correct mapping window size and
number of mapping windows based on the value of device tree property
'ranges' and the capability of of the iProc PCIe controller.
Signed-off-by: Oza Oza <oza.oza@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Add support for the second generation of the iProc PCIe PAXC host
controller.
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
After we send a PCI_EJECTION_COMPLETE message to the host, the host will
immediately send us a PCI_BUS_RELATIONS message with
relations->device_count == 0, so pci_devices_present_work(), running on
another thread, can find the being-ejected device, mark the
hpdev->reported_missing to true, and run list_move_tail()/list_del() for
the device -- this races hv_eject_device_work() -> list_del().
Move the list_del() in hv_eject_device_work() to an earlier place, i.e.,
before we send PCI_EJECTION_COMPLETE, so later the
pci_devices_present_work() can't see the device.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jake Oshins <jakeo@microsoft.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
CC: Haiyang Zhang <haiyangz@microsoft.com>
CC: Vitaly Kuznetsov <vkuznets@redhat.com>
1. We don't really need such a big on-stack buffer when sending the
teardown_packet: vmbus_sendpacket() here only uses sizeof(struct
pci_message).
2. In the hot-remove case (PCI_EJECT), after we send PCI_EJECTION_COMPLETE
to the host, the host will send a RESCIND_CHANNEL message to us and the
host won't access the per-channel ringbuffer any longer, so we needn't send
PCI_RESOURCES_RELEASED/PCI_BUS_D0EXIT to the host, and we shouldn't expect
the host's completion message of PCI_BUS_D0EXIT, which will never come.
3. We should send PCI_BUS_D0EXIT after hv_send_resources_released().
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jake Oshins <jakeo@microsoft.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
CC: Haiyang Zhang <haiyangz@microsoft.com>
CC: Vitaly Kuznetsov <vkuznets@redhat.com>
We don't really need such a big on-stack buffer. vmbus_sendpacket() here
only uses sizeof(struct pci_child_message).
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jake Oshins <jakeo@microsoft.com>
I returned to Synopsys and so I am sending this patch to update the email
address of the pcie-designware-plat author.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
During enumeration with multi-function EP devices, access to the
configuration space of a non-existent function results in an unsupported
request being returned as expected. By default the PAXB-based iProc PCIe
controller forwards this as an APB error to the host system and that causes
an exception, which is undesired.
Disable this undesired behaviour and let the kernel PCI stack deal with an
access to the non-existent function, in which case a vendor ID of 0xffff is
returned and handled gracefully.
Reported-by: JD Zheng <jiandong.zheng@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: JD Zheng <jiandong.zheng@broadcom.com>
Reviewed-by: Oza Oza <oza.oza@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
