this patch registers the wakeup irq, sets a gpio pin to indicate the
status of system for suspend/resume operations, and adds the machine to
the supported machines for use with the simtec-pm
Signed-off-by: David Anders <danders@amltd.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Switch arch/arm/kernel/apm.c from using kernel_thread - whose export
is deprecated - to kthread.
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
hi,
a quick find -iname \*.[ch] | xargs grep "> ARRAY_SIZE(", revealed
these in the icst drivers.
If i == ARRAY_SIZE, we get past the idx2s array.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds another hook into sharpsl_pm to notify the machine
specific driver immediately after resume. This is needed to support the Sharp SL-6000 (Tosa).
Signed-off-by: Dirk Opfer <Dirk@Opfer-Online.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Locomo chip has a SPI interface which is used for SD/MMC cards (only collie).
This patch adds the definition for the SPI device inside the Locomo chip.
Signed-off-by: Dirk Opfer <Dirk@Opfer-Online.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert LOMOMO to use struct device * for GPIOs instead of struct
locomo_dev. This enables access to the GPIOs from code which is not
a locomo device itself (such as audio). Access for gpio 31 is removed
for error handling (no such hardware exists).
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ARM Versatile board PCI config space read routines are broken for byte
accesses. The access uses a byte read, so masking the bottom two bits of the
address is wrong.
I guess this is a cut/paste error from the the halfword code which uses
aligned word access+shift+mask.
Signed-off-by: Paul Brook <paul@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ARM XIP_KERNEL map created in devicemaps_init() is wrong.
The map.pfn is rounded down to an even 1MiB section boundary
which results in va/pa translations errors when XIP_PHYS_ADDR
starts on an odd 1MiB boundary and this causes the kernel to
hang. This patch fixes ARM XIP_KERNEL translation errors for
the odd 1MiB XIP_PHYS_ADDR boundary case.
Signed-off-by: George G. Davis <gdavis@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add S3C2412 power management code, and move the
core register saving in from s3c2412.c
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the AML M5900 series to the list of supported machines in the
arch/arm/mach-s3c2410 directory. This ensures the core peripherals
are registered, and the timer source is configured. if selected in
the kernel config the framebuffer registers and mtd partition
information are set. This version of the patch has corrected
formatting and removed the legacy procfs directory entry.
Signed-off-by: David Anders <danders@amltd.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Mostly clean up CONFIG_OMAP_RESET_CLOCKS. Also includes a
patch from Imre Deak to make McSPI clocks use id.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch syncs OMAP DMA code with linux-omap tree.
Mostly allow changing DMA callback function and set
OMAP2 specific transfer mode.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some peripherals seem to need additional delay until they
can actually be accessed after enabling their FCLK and ICLK.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enabling and disabling the 54 MHz and 96 MHz APLLs can happen
unnecessarily often during bootup. Make sure they're kept
enabled during init.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In OMAP2420, an incoming GPIO interrupt always sets both GPIO_IRQSTATUS1
and GPIO_IRQSTATUS2, even if the relevant bit is disabled in
GPIO_IRQENABLE1/2 and DSP doesn't use GPIO at all. GPIO_IRQSTATUS1
is for MPU and GPIO_IRQSTATUS2 is for DSP. If IRQSTATUS is set, this
will prevent the system from going to idle state. This patch also clears
IRQSTATUS2 to avoid the above situation.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPT1 will be set into non-posted mode, and the wakeup register
is set for all timers.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some boards might use the oscillator clock for powering
external peripherals. Add support for making sure osc_ck
stays active even when trying to go to sleep.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add enable/disable functions which effectively control the GPT iclk and fclk.
Signed-off-by: Timo Teras <timo.teras@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove Remove superfluous/recursive locking for GPIO
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM11 can't access the IVA interrupt controller from
IVA slave port.
From Richard Woodruff:
"The 0x40000000 is an IVA-ARM7 local bus address.
The IVA-INTC is NOT accessible through the IVA-L3-Slave Port.
The current TRM does say this directly and indirectly in a few spots and
in figures."
Signed-off-by: Komal Shah <komal_shah802003@yahoo.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
After adjusting clock parameters, OMAP2 CPUs need a memory
barrier to make sure the changes go into effect immediately.
Otherwise bad things will happen if we try to access the
peripheral whose clock is just being enabled.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A forgotten parenthesis in clock.c caused the PLL stabilization loop
to not be executed correctly.
Signed-off-by: Samuel Ortiz <samuel.ortiz@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch makes the OMAP2 dmtimers module using the interface
clocks only while the registers are accessed (except GPT1 which has
iclk enabled all the time).
Signed-off-by: Timo Teras <timo.teras@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for assigning memory regions dynamically to peripherals
attached to GPMC interface. Platform specific code should now call
gpmc_cs_request to get a free GPMC memory region instead of using
a fixed address.
Make the H4 and Apollon platform initialization use the new API.
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The recent MPUIO range change fix breaks compilation if
CONFIG_ARCH_OMAP24XX isn't defined; it should be OMAP_MAX_GPIO_LINES not
MAX_GPIO_LINES I believe. This one liner fixes it.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds pin mux info for the SPI master/slave interface on
OMAP16xx. Data from OMAP 1611/1612 TRM and errata. Works for me on my
1611/H2 with current git kernel.
Signed-off-by: Mark Howell <mhowell@northlink.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We have to make sure that the LCD DMA external destination bit is
cleared by default, otherwise OMAP won't sleep.
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- MPUIO doesn't exist on OMAP2
- no error was returned for too big MPUIO numbers
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
McBSP does not need sys_ck or sys_clkout. If the devices connected
to McBSP need sys_clkout, they need to request it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Apollon board MMC supports on OMAP2
TODO:
We have to check MMC on H4
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reprogramming takes places before putting the CPU into idle mode if
the dynamic tick option is enabled. The timer is then set to expire
at the next pending timer event. Because some time has already passed
since the last reported jiffy we have to wait less than the time
specified in jiffies.
Also make sure we don't set a load value of 0 whose outcome is
unspecified according to the TRM.
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adds support for CONFIG_DEBUG_ICEDCC for ARM11.
Tested on ARM1136 (OMAP2420).
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- Document the meaning for OP_SCALAR, OP_SD and add OP_DD.
- Formatting cleanups
- Remove now redundant code for making compare instructions
operate on scalar values.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
VECITR in Floating-Point Exception register indicates the number of
remaining short vector iterations after a potential exception was
detected.
In case of exception caused by scalar instructions, VECITR is NOT updated.
Therefore emulation for VFP must ignore VECITR field
and treat "veclen" as zero when recognizing scalar instructing.
Signed-off-by: Gen Fukatsu <fukatsu.gen@jp.panasonic.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The documentation for the ZBOOT_ROM_BSS config option describes it as
"The base address of 64KiB of read/write memory in the target for the
ROM-able zImage..." In actuality, it requires more than 100 KiB of
space in addition to enough space to hold the decompressed kernel.
This patch fixes the description in the Kconfig file.
Signed-off-by: Dan Fandrich <dfandrich@intrinsyc.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix thinko in the flush_ptrace_access() "if (expr)" for the ARM
VIPT non-aliasing cache case. We only need to flush cache when
VM_EXEC is set in vma->vm_flags but "if (expr) always evaluates
to true on UP systems for the ARM VIPT non-aliasing cache case.
Signed-off-by: George G. Davis <gdavis@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the IO-Data GLAN Tank, from Martin Michlmayr.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the Thecus n2100 (80219-based.)
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the redundant Modification lines from
the top of the files in arch/arm/mach-s3c2410
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
