- Add shared input select register support
- imx7d has two iomux controllers iomuxc and iomuxc-lpsr
which share select_input register for daisy chain settings
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allow mux_reg offset zero to be a valid pin_id, on imx7d
mux_conf reg offset is zero for iomuxc-lspr controller
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix system chrash caused by groups whose number is smaller than the number
of groups of the last pinctl instance which is not initialized.
iMX7D supports two iomux controllers (iomuxc-lpsr and iomuxc) on probing
the second instance (iomuxc) the chrash below occurs.
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.2.0-next-20150901-00006-gebfa43c (aalonso@bluefly)
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7)
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasin instruction cache
[ 0.000000] Machine model: Freescale i.MX7 SabreSD Board
[ 0.661012] [<802a6cb0>] (strcmp) from [<802cc80c>] (imx_dt_node_to_map+0x58/0x208)
[ 0.668879] [<802cc80c>] (imx_dt_node_to_map) from [<802cbe24>] (pinctrl_dt_to_map+0x174/0x2b0)
[ 0.677654] [<802cbe24>] (pinctrl_dt_to_map) from [<802c8f18>] (pinctrl_get+0x100/0x424)
[ 0.685878] [<802c8f18>] (pinctrl_get) from [<802c9510>] (pinctrl_register+0x26c/0x480)
[ 0.694104] [<802c9510>] (pinctrl_register) from [<802ccf3c>] (imx_pinctrl_probe+0x580/0x6e8)
[ 0.702706] [<802ccf3c>] (imx_pinctrl_probe) from [<80351b58>] (platform_drv_probe+0x44/0xa4)
[ 0.711455] [<80351b58>] (platform_drv_probe) from [<803503ec>] (driver_probe_device+0x174/0x2b4)
[ 0.720405] [<803503ec>] (driver_probe_device) from [<803505fc>] (__driver_attach+0x8c/0x90)
[ 0.728982] [<803505fc>] (__driver_attach) from [<8034e930>] (bus_for_each_dev+0x6c/0xa0)
[ 0.737381] [<8034e930>] (bus_for_each_dev) from [<8034fb88>] (bus_add_driver+0x148/0x1f0)
[ 0.745804] [<8034fb88>] (bus_add_driver) from [<80350c00>] (driver_register+0x78/0xf8)
[ 0.753880] [<80350c00>] (driver_register) from [<800097d0>] (do_one_initcall+0x8c/0x1d4)
[ 0.762282] [<800097d0>] (do_one_initcall) from [<80987dac>] (kernel_init_freeable+0x144/0x1e4)
[ 0.771061] [<80987dac>] (kernel_init_freeable) from [<806d9c7c>] (kernel_init+0x8/0xe8)
[ 0.779285] [<806d9c7c>] (kernel_init) from [<8000f628>] (ret_from_fork+0x14/0x2c)
[ 0.786981] Code: e3520000 e5e32001 1afffffb e12fff1e (e4d03001)
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allow GPIOs to be configured as wakeup sources. When going to suspend,
disable all GPIO irqs excepting the one configured as wakeup sources.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allwinner A83T soc port controller has 8 ports.
It has 3 IRQ banks namely PB, PG, PH.
Pinmuxing are different for some pins as compared to
sun8i A23 and A33.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's not needed an is just creating a null statement, so remove it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's not needed an is just creating a null statement, so remove it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's not needed an is just creating a null statement, so remove it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's not needed an is just creating a null statement, so remove it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
They aren't needed and are just creating null statements so remove it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
They aren't needed and are just creating null statements so remove it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds EthernetAVB
Based on a much lager patch by Takeshi Kihara which was
originally posted by Kuninori Morimoto.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
[horms: extracted from a larger patch;
corrected swapped {MATCH,CAPTURE_A} pins]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Now, PINMUX_IPSR_MSEL() and PINMUX_IPSR_MODSEL_DATA() are same.
Current PFC driver is very difficult to read, because macro names are
using different length.
PINMUX_IPSR_NOGP(ispr, ...)
PINMUX_IPSR_DATA(ipsr, ...)
PINMUX_IPSR_NOGM(ispr, ...)
PINMUX_IPSR_NOFN(ipsr, ...)
PINMUX_IPSR_MSEL(ipsr, ...)
PINMUX_IPSR_MODSEL_DATA(ipsr, ...)
It can be readable if we can use PINMUX_IPSR_MSEL() instead
of PINMUX_IPSR_MODSEL_DATA()
PINMUX_IPSR_NOGP(ispr, ...)
PINMUX_IPSR_DATA(ipsr, ...)
PINMUX_IPSR_NOGM(ispr, ...)
PINMUX_IPSR_NOFN(ipsr, ...)
PINMUX_IPSR_MSEL(ipsr, ...)
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Now, PINMUX_IPSR_MSEL() and PINMUX_IPSR_MODSEL_DATA() are same.
Current PFC driver is very difficult to read, because macro names are
using different length.
PINMUX_IPSR_NOGP(ispr, ...)
PINMUX_IPSR_DATA(ipsr, ...)
PINMUX_IPSR_NOGM(ispr, ...)
PINMUX_IPSR_NOFN(ipsr, ...)
PINMUX_IPSR_MSEL(ipsr, ...)
PINMUX_IPSR_MODSEL_DATA(ipsr, ...)
It can be readable if we can use PINMUX_IPSR_MSEL() instead
of PINMUX_IPSR_MODSEL_DATA()
PINMUX_IPSR_NOGP(ispr, ...)
PINMUX_IPSR_DATA(ipsr, ...)
PINMUX_IPSR_NOGM(ispr, ...)
PINMUX_IPSR_NOFN(ipsr, ...)
PINMUX_IPSR_MSEL(ipsr, ...)
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Now, PINMUX_IPSR_MSEL() and PINMUX_IPSR_MODSEL_DATA() are same.
Current PFC driver is very difficult to read, because macro names are
using different length.
PINMUX_IPSR_NOGP(ispr, ...)
PINMUX_IPSR_DATA(ipsr, ...)
PINMUX_IPSR_NOGM(ispr, ...)
PINMUX_IPSR_NOFN(ipsr, ...)
PINMUX_IPSR_MSEL(ipsr, ...)
PINMUX_IPSR_MODSEL_DATA(ipsr, ...)
It can be readable if we can use PINMUX_IPSR_MSEL() instead
of PINMUX_IPSR_MODSEL_DATA()
PINMUX_IPSR_NOGP(ispr, ...)
PINMUX_IPSR_DATA(ipsr, ...)
PINMUX_IPSR_NOGM(ispr, ...)
PINMUX_IPSR_NOFN(ipsr, ...)
PINMUX_IPSR_MSEL(ipsr, ...)
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Now, PINMUX_IPSR_MSEL() and PINMUX_IPSR_MODSEL_DATA() are same.
Current PFC driver is very difficult to read, because macro names are
using different length.
PINMUX_IPSR_NOGP(ispr, ...)
PINMUX_IPSR_DATA(ipsr, ...)
PINMUX_IPSR_NOGM(ispr, ...)
PINMUX_IPSR_NOFN(ipsr, ...)
PINMUX_IPSR_MSEL(ipsr, ...)
PINMUX_IPSR_MODSEL_DATA(ipsr, ...)
It can be readable if we can use PINMUX_IPSR_MSEL() instead
of PINMUX_IPSR_MODSEL_DATA()
PINMUX_IPSR_NOGP(ispr, ...)
PINMUX_IPSR_DATA(ipsr, ...)
PINMUX_IPSR_NOGM(ispr, ...)
PINMUX_IPSR_NOFN(ipsr, ...)
PINMUX_IPSR_MSEL(ipsr, ...)
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Now, PINMUX_IPSR_MSEL() and PINMUX_IPSR_MODSEL_DATA() are same.
Current PFC driver is very difficult to read, because macro names are
using different length.
PINMUX_IPSR_NOGP(ispr, ...)
PINMUX_IPSR_DATA(ipsr, ...)
PINMUX_IPSR_NOGM(ispr, ...)
PINMUX_IPSR_NOFN(ipsr, ...)
PINMUX_IPSR_MSEL(ipsr, ...)
PINMUX_IPSR_MODSEL_DATA(ipsr, ...)
It can be readable if we can use PINMUX_IPSR_MSEL() instead
of PINMUX_IPSR_MODSEL_DATA()
PINMUX_IPSR_NOGP(ispr, ...)
PINMUX_IPSR_DATA(ipsr, ...)
PINMUX_IPSR_NOGM(ispr, ...)
PINMUX_IPSR_NOFN(ipsr, ...)
PINMUX_IPSR_MSEL(ipsr, ...)
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The difference between PINMUX_IPSR_MSEL() and PINMUX_IPSR_MODSEL_DATA()
are FN_xxx order, and PINMUX_IPSR_MSEL() is used only from r8a7778.
Now it r8a7778 works correctly with PINMUX_IPSR_MODSEL_DATA() order.
This means we can merge PINMUX_IPSR_MSEL() and PINMUX_IPSR_MODSEL_DATA().
Current PFC driver is very difficult to read, because macro names are
using different length. Especially PINMUX_IPSR_MODSEL_DATA() is well
used macro
PINMUX_IPSR_NOGP(ispr, ...)
PINMUX_IPSR_DATA(ipsr, ...)
PINMUX_IPSR_NOGM(ispr, ...)
PINMUX_IPSR_NOFN(ipsr, ...)
PINMUX_IPSR_MSEL(ipsr, ...)
PINMUX_IPSR_MODSEL_DATA(ipsr, ...)
It can be readable if we can merge
PINMUX_IPSR_MSEL() and PINMUX_IPSR_MODSEL_DATA()
PINMUX_IPSR_NOGP(ispr, ...)
PINMUX_IPSR_DATA(ipsr, ...)
PINMUX_IPSR_NOGM(ispr, ...)
PINMUX_IPSR_NOFN(ipsr, ...)
PINMUX_IPSR_MSEL(ipsr, ...)
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Now that all ARM-based Renesas SoCs use multiplatform kernels only the
hardcoded IRQ numbers can be dropped as they're dynamically allocated.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Shmobile is all multiplatform these days, so get rid of the reference to
CONFIG_ARCH_SHMOBILE_LEGACY.
Move the legacy code to do the non-DT mapping between GPIOs and pins
inside the existing #ifdef CONFIG_SUPERH section.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
When using serial port SCIFB1_B, transmit works, but nothing is
received.
Receive fails because the SCIFB1_SCK_B settings configure the wrong
value for the sel_scifb1 field in the Module Select Register (MOD_SEL),
due to an ambiguity in the R-Car M2-W and M2-N datasheets.
Tested on r8a7791/koelsch using pins 53 (TXD) and 72 (RXD) on EXIO
Connector A.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
SCIF0 on R-Car E2 does not have an SCK pin.
"SCIF_CLK" is the (H)SCIF baud rate generation clock pin, which is not
yet supported.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Legacy function GPIOs are no longer used on ARM since commit
a27c5cd1a0 ("sh-pfc: sh73a0: Remove function GPIOs").
Extract its setup code into a separate function, and make all function
GPIO related code and data depend on CONFIG_SUPERH.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
gpio_chip.free() is optional, and can just be left unimplemented.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
On platforms where the PFC/GPIO controller is instantiated from DT, the
mapping between GPIOs and pins is set up using the "gpio-ranges"
property in DT.
Hence stop setting up the mapping from C code on DT platforms.
This code is still used for SH or ARM-legacy platforms.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The mediatek pinctrl driver uses the BIT() macro instead of open
coding 1 << n in all but one place. Replace this occurrence with
the BIT() macro for consistency.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Many parts of pinctrl rk3036 are similar to rk2928's.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull ARM fixes from Russell King:
"Three fixes and a resulting cleanup for -rc2:
- Andre Przywara reported that he was seeing a warning with the new
cast inside DMA_ERROR_CODE's definition, and fixed the incorrect
use.
- Doug Anderson noticed that kgdb causes a "scheduling while atomic"
bug.
- OMAP5 folk noticed that their Thumb-2 compiled X servers crashed
when enabling support to cover ARMv6 CPUs due to a kernel bug
leaking some conditional context into the signal handler"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8425/1: kgdb: Don't try to stop the machine when setting breakpoints
ARM: 8437/1: dma-mapping: fix build warning with new DMA_ERROR_CODE definition
ARM: get rid of needless #if in signal handling code
ARM: fix Thumb2 signal handling when ARMv6 is enabled
- Fix a memory allocation size in the devfreq core (Xiaolong Ye).
- Fix a mistake in the exynos-ppmu DT binding (Javier Martinez
Canillas).
- Add support for PPMUv2 ((Platform Performance Monitoring Unit
version 2.0) on the Exynos5433 SoCs (Chanwoo Choi).
- Fix a type casting bug in the Exynos PPMU code (MyungJoo Ham).
- Assorted devfreq code cleanups and optimizations (Javi Merino,
MyungJoo Ham, Viresh Kumar).
- Fix up the ACPI cpufreq driver to use a more lightweight way
to get to its private data in the ->get() callback (Rafael J
Wysocki).
- Fix a CONFIG_ prefix bug in one of the ACPI drivers and make
the ACPI subsystem use IS_ENABLED() instead of #ifdefs in
function bodies (Sudeep Holla).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=+ZST
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"Included are: a somewhat late devfreq update which however is mostly
fixes and cleanups with one new thing only (the PPMUv2 support on
Exynos5433), an ACPI cpufreq driver fixup and two ACPI core cleanups
related to preprocessor directives.
Specifics:
- Fix a memory allocation size in the devfreq core (Xiaolong Ye).
- Fix a mistake in the exynos-ppmu DT binding (Javier Martinez
Canillas).
- Add support for PPMUv2 ((Platform Performance Monitoring Unit
version 2.0) on the Exynos5433 SoCs (Chanwoo Choi).
- Fix a type casting bug in the Exynos PPMU code (MyungJoo Ham).
- Assorted devfreq code cleanups and optimizations (Javi Merino,
MyungJoo Ham, Viresh Kumar).
- Fix up the ACPI cpufreq driver to use a more lightweight way to get
to its private data in the ->get() callback (Rafael J Wysocki).
- Fix a CONFIG_ prefix bug in one of the ACPI drivers and make the
ACPI subsystem use IS_ENABLED() instead of #ifdefs in function
bodies (Sudeep Holla)"
* tag 'pm+acpi-4.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: acpi-cpufreq: Use cpufreq_cpu_get_raw() in ->get()
ACPI: Eliminate CONFIG_.*{, _MODULE} #ifdef in favor of IS_ENABLED()
ACPI: int340x_thermal: add missing CONFIG_ prefix
PM / devfreq: Fix incorrect type issue.
PM / devfreq: tegra: Update governor to use devfreq_update_stats()
PM / devfreq: comments for get_dev_status usage updated
PM / devfreq: drop comment about thermal setting max_freq
PM / devfreq: cache the last call to get_dev_status()
PM / devfreq: Drop unlikely before IS_ERR(_OR_NULL)
PM / devfreq: exynos-ppmu: bit-wise operation bugfix.
PM / devfreq: exynos-ppmu: Update documentation to support PPMUv2
PM / devfreq: exynos-ppmu: Add the support of PPMUv2 for Exynos5433
PM / devfreq: event: Remove incorrect property in exynos-ppmu DT binding
in the framework to avoid oops when get_parent ops return out of range
values on tegra platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=LSuc
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A few driver fixes for tegra, rockchip, and st SoCs and a two-liner in
the framework to avoid oops when get_parent ops return out of range
values on tegra platforms"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
drivers: clk: st: Rename st_pll3200c32_407_c0_x into st_pll3200c32_cx_x
clk: check for invalid parent index of orphans in __clk_init()
clk: tegra: dfll: Properly protect OPP list
clk: rockchip: add critical clock for rk3368
- Batch of minor fixups to the new hfi1 driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=hsxv
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"The new hfi1 driver in staging/rdma has had a number of fixup patches
since being added to the tree. This is the first batch of those fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
IB/hfi: Properly set permissions for user device files
IB/hfi1: mask vs shift confusion
IB/hfi1: clean up some defines
IB/hfi1: info leak in get_ctxt_info()
IB/hfi1: fix a locking bug
IB/hfi1: checking for NULL instead of IS_ERR
IB/hfi1: fix sdma_descq_cnt parameter parsing
IB/hfi1: fix copy_to/from_user() error handling
IB/hfi1: fix pstateinfo from returning improperly byteswapped value
Pull libnvdimm fixes from Dan Williams:
- a boot regression (since v4.2) fix for some ARM configurations from
Tyler
- regression (since v4.1) fixes for mkfs.xfs on a DAX enabled device
from Jeff. These are tagged for -stable.
- a pair of locking fixes from Axel that are hidden from lockdep since
they involve device_lock(). The "btt" one is tagged for -stable, the
other only applies to the new "pfn" mechanism in v4.3.
- a fix for the pmem ->rw_page() path to use wmb_pmem() from Ross.
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
mm: fix type cast in __pfn_to_phys()
pmem: add proper fencing to pmem_rw_page()
libnvdimm: pfn_devs: Fix locking in namespace_store
libnvdimm: btt_devs: Fix locking in namespace_store
blockdev: don't set S_DAX for misaligned partitions
dax: fix O_DIRECT I/O to the last block of a blockdev
Pull block updates from Jens Axboe:
"This is a bit bigger than it should be, but I could (did) not want to
send it off last week due to both wanting extra testing, and expecting
a fix for the bounce regression as well. In any case, this contains:
- Fix for the blk-merge.c compilation warning on gcc 5.x from me.
- A set of back/front SG gap merge fixes, from me and from Sagi.
This ensures that we honor SG gapping for integrity payloads as
well.
- Two small fixes for null_blk from Matias, fixing a leak and a
capacity propagation issue.
- A blkcg fix from Tejun, fixing a NULL dereference.
- A fast clone optimization from Ming, fixing a performance
regression since the arbitrarily sized bio's were introduced.
- Also from Ming, a regression fix for bouncing IOs"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: fix bounce_end_io
block: blk-merge: fast-clone bio when splitting rw bios
block: blkg_destroy_all() should clear q->root_blkg and ->root_rl.blkg
block: Copy a user iovec if it includes gaps
block: Refuse adding appending a gapped integrity page to a bio
block: Refuse request/bio merges with gaps in the integrity payload
block: Check for gaps on front and back merges
null_blk: fix wrong capacity when bs is not 512 bytes
null_blk: fix memory leak on cleanup
block: fix bogus compiler warnings in blk-merge.c
Commit 505a666ee3 ("writeback: plug writeback in wb_writeback() and
writeback_inodes_wb()") has us holding a plug during writeback_sb_inodes,
which increases the merge rate when relatively contiguous small files
are written by the filesystem. It helps both on flash and spindles.
For an fs_mark workload creating 4K files in parallel across 8 drives,
this commit improves performance ~9% more by unplugging before calling
cond_resched(). cond_resched() doesn't trigger an implicit unplug, so
explicitly getting the IO down to the device before scheduling reduces
latencies for anyone waiting on clean pages.
It also cuts down on how often we use kblockd to unplug, which means
less work bouncing from one workqueue to another.
Many more details about how we got here:
https://lkml.org/lkml/2015/9/11/570
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The various definitions of __pfn_to_phys() have been consolidated to
use a generic macro in include/asm-generic/memory_model.h. This hit
mainline in the form of 012dcef3f0 "mm: move __phys_to_pfn and
__pfn_to_phys to asm/generic/memory_model.h". When the generic macro
was implemented the type cast to phys_addr_t was dropped which caused
boot regressions on ARM platforms with more than 4GB of memory and
LPAE enabled.
It was suggested to use PFN_PHYS() defined in include/linux/pfn.h
as provides the correct logic and avoids further duplication.
Reported-by: kernelci.org bot <bot@kernelci.org>
Suggested-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
