drivers/net/wireless/iwlwifi/iwl-tx.c: In function `iwl_hw_txq_ctx_free':
drivers/net/wireless/iwlwifi/iwl-tx.c:410: warning: suggest explicit braces to avoid ambiguous `else'
Cc: Zhu Yi <yi.zhu@intel.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some devices have 40MHz operation disabled entirely. Ensure that driver do
not enable 40MHz operation if a channel does not allow this.
This fixes http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2135
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Recent powersaving work resulted in power management ops being called
during EEPROM initialization. The lock used by these functions is not
initialized at this time. Ensure lock is initialized before it is used.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we see from http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2125
that power saving does not work well on 3945. Since then power saving has
also been connected with association problems where an AP deathenticates a
3945 after it is unable to transmit data to it - this happens when 3945
enters power savings mode.
Disable power save support until issues are resolved.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I've also for a long time had a problem with the
temperature calculation code, which I had fixed
by byte-swapping the values, and now it turns out
that was the correct fix after all.
Also, any use of iwl_eeprom_query_addr() that is
for more than a u8 must be cast to little endian,
and some structs as well.
Fix all this. Again, no real impact on platforms
that already are little endian.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The construct "le16_to_cpu((__force __le16)(r >> 16))" has
always bothered me when looking through the iwlwifi code,
it shouldn't be necessary to __force anything, and before
this code, "r" was obtained with an ioread32, which swaps
each of the two u16 values in it properly when swapping the
entire u32 value. I've had arguments about this code with
people before, but always conceded they were right because
removing it only made things not work at all on big endian
platforms.
However, analysing a failure of the OTP reading code, I now
finally figured out what is going on, and why my intuition
about that code being wrong was right all along.
It turns out that the 'priv->eeprom' u8 array really wants
to have the data in it in little endian. So the force code
above and all really converts *to* little endian, not from
it. Cf., for instance, the function iwl_eeprom_query16() --
it reads two u8 values and combines them into a u16, in a
little-endian way. And considering it more, it makes sense
to have the eeprom array as on the device, after all not
all values really are 16-bit values, the MAC address for
instance is not.
Now, what this really means is that all the annotations are
completely wrong. The eeprom reading code should fill the
priv->eeprom array as a __le16 array, with __le16 values.
This also means that iwl_read_otp_word() should really have
a __le16 pointer as the data argument, since it should be
filling that in a format suitable for priv->eeprom.
Propagating these changes throughout, iwl_find_otp_image()
is found to be, now obviously visible, defective -- it uses
the data returned by iwl_read_otp_word() directly as if it
was CPU endianness. Fixing that, which is this hunk of the
patch:
- next_link_addr = link_value * sizeof(u16);
+ next_link_addr = le16_to_cpu(link_value) * sizeof(u16);
is the only real change of this patch. Everything else is
just fixing the sparse annotations.
Also, the bug only shows up on big endian platforms with a
1000 series card. 5000 and previous series do not use OTP,
and 6000 series has shadow RAM support which means we don't
ever use the defective code on any cards but 1000.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When trigger event log dumping from debugfs, the entire event log
should be dumped and the size should match the number of events being
dump.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Recent commits "iwlwifi: remove power-wasting calls to apm_ops.init()" and
"iwlagn: power up device before initializing EEPROM" had the goal of
reducing device power consumption from the time the module is loaded until
the interface is brought up and the device's power saving mechanisms kick
in. The idea is that once the module is loaded there is no need for the
device to consume power until the interface is brought up.
With the current solution the device is only powered up during EEPROM read,
and then so also only if the EEPROM type is OTP. We have found that on
certain platforms even non-OTP devices require power to be up during EEPROM
read. On these platforms the driver never loads and the system log contains
the following:
iwlagn 0000:03:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0x080403D8
We thus now power up all devices during EEPROM read.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In iwlwifi, priv->alloc_rxb_page is used to keep track of the Rx
pages allocated by the driver. This cleans up the page free routines
by introducing __iwl_free_pages/iwl_free_pages so that the accounting
is more accurate and less error prone. This also fixes two instances where
the counter was not updated.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] drivers/net/wireless/iwlwifi/iwl-tx.o
drivers/net/wireless/iwlwifi/iwl-tx.c: In function ‘iwl_tx_agg_stop’:
drivers/net/wireless/iwlwifi/iwl-tx.c:1356: warning: passing argument 1 of ‘ieee80211_stop_tx_ba_cb_irqsafe’ from incompatible pointer type
include/net/mac80211.h:2128: note: expected ‘struct ieee80211_vif *’ but argument is of type ‘struct ieee80211_hw *’
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver version number is a remnant from when there was an out-of-tree
iwlwifi driver. Now that the driver forms part of kernel source we do not
need a separate driver version. Instead, we now use the kernel version as
driver version. We maintain the previous tags used to indicate which
components the driver has been compiled with.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
error_event_table_ptr is only set upon receipt of REPLY_ALIVE. Until
then both event log and error log will fail. Add information to indicate
which uCode encounter the failure case.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the process of improving uCode event logging capability, the new
implementation was introduced without removing the existing
implementation. The event log will be dumped to dmesg twice.
Remove the old implementation to only log the event once upon sys
assert or request by user.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lennert Buytenhek noticed that delBA handling in mac80211
was broken and has remotely triggerable problems, some of
which are due to some code shuffling I did that ended up
changing the order in which things were done -- this was
commit d75636ef9c
Author: Johannes Berg <johannes@sipsolutions.net>
Date: Tue Feb 10 21:25:53 2009 +0100
mac80211: RX aggregation: clean up stop session
and other parts were already present in the original
commit d92684e660
Author: Ron Rindjunsky <ron.rindjunsky@intel.com>
Date: Mon Jan 28 14:07:22 2008 +0200
mac80211: A-MPDU Tx add delBA from recipient support
The first problem is that I moved a BUG_ON before various
checks -- thereby making it possible to hit. As the comment
indicates, the BUG_ON can be removed since the ampdu_action
callback must already exist when the state is != IDLE.
The second problem isn't easily exploitable but there's a
race condition due to unconditionally setting the state to
OPERATIONAL when a delBA frame is received, even when no
aggregation session was ever initiated. All the drivers
accept stopping the session even then, but that opens a
race window where crashes could happen before the driver
accepts it. Right now, a WARN_ON may happen with non-HT
drivers, while the race opens only for HT drivers.
For this case, there are two things necessary to fix it:
1) don't process spurious delBA frames, and be more careful
about the session state; don't drop the lock
2) HT drivers need to be prepared to handle a session stop
even before the session was really started -- this is
true for all drivers (that support aggregation) but
iwlwifi which can be fixed easily. The other HT drivers
(ath9k and ar9170) are behaving properly already.
Reported-by: Lennert Buytenhek <buytenh@marvell.com>
Cc: stable@kernel.org
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Current blinking rate is calculated based on the difference between
current tx/rx byte counts and priv->led_tpt.
priv->led_tpt should not get reset in iwl_leds_init(), this function can be
called by bring interface "up" or "down", or when uCode sysassert occurred.
resetting the led_tpt parameter will introduce incorrect led blinking behavior.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change error message for command queue full
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Acked-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To help iwlagn uCode debugging, event log will dump to syslog when driver
detect uCode error occurred, but this only happen when compile with
CONFIG_IWLWIFI_DEBUG and debug flag is enabled; which is not always
the case. Also, there is another problem, if the flag is set, the entire
event log buffer will be dump to syslog, it can flood the syslog and
make it very difficult to debug the problem.
Change the default to only dump last 20 entries of event log to syslog
unless the following condition meets:
1. both compile with CONFIG_IWLWIFI_DEBUG and debug flag
is enabled, and then dump the entire event buffer to syslog.
2. dump event log request from debugfs
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Acked-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we get a state change of associated or not, we need to tell the
ucode via the RX_ON command using the filter flags. This will prevent
the ucode from sending any packets when not associated, specifically not
sending NULL QOS packets after a deauthentication which causes the AP to
repeatedly send deauth's in some situations.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
uCode error log contain information as to what the error was and where
it occurred necessary to debug any uCode issues.
Always log the information without special debug flag, this can help to
capture the important information when error happened.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Acked-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For "sram" debugfs file, if user did not specify the offset and length,
dump the entire data portion of sram by default.
Data portion is 0x800000 - 0x80ffff, but the actual data size is known
to the driver from the ucode file.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the PCI_ID list for 5xx0 series.
Remove all the PCI_IDs which never made into production or not longer in
production.
Also make sure the supported bands(a/b/g/n) match specified PCI_IDs
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since IO tracing is usually not needed and
generates a lot of data, separate it into
its own trace system so that we can always
enable iwlwifi:* and not have to worry about
getting too much data. If IO tracing is then
really needed we can enable iwlwifi_io:* in
addition and get that data.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
reserved2 field in "struct iwl4965_addsta_cmd" is __le16.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dynamically allocate memory for dumping SRAM based on the length of memory
to be displayed.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For tx_queue, need to increase the buffer size allocated for it,
so all the queues information can be displayed
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set the correct Read/Write file permission for iwlwifi debugfs files
based on the functionality of the files
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
LED blink rate is based on the traffic load, when tx/rx traffic counts
got reset, we also need to reset the led_tpt to prevent incorrect
blink rate being calculated.
Merge both clear_tx_statistics() and clear_rx_statistics() into
single clear_traffic_statistics() function, when reset the traffic byte
counts, both tx and rx need to be reset at the same time, to make
sure calculated the correct led blink rate.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Setting "Spatial multiplexing Power Save" as part of
per device configuration parameter.
Report to uCode based on priv->conf setting, so driver can
have more control of how different devices should operate
in power save mode.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
LED blinking rate is based on tx/rx traffic, the most reasonable place
to do it is after update the traffic byte counts
This fixes the recent LED blinking breakage on 3945 introduced by "iwlwifi:
separate led function from statistic notification"
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CSR_INT_COALESCING previously had only one, but now has two single-byte fields.
With only one single-byte field (lowest order byte) it was okay to write via
iwl_write32(), but now with two, an iwl_write32() to the lower order field
clobbers the other field (odd-address CSR_INT_PERIODIC_REG, offset 0x5), and an
iwl_write32() to CSR_INT_PERIODIC_REG could clobber the lowest byte of the
next-higher register (CSR_INT, offset 0x8).
Fortunately, no bad side effects have been produced by the iwl_write32()
usage, due to order of execution (low order byte was always written before
higher order byte), and the fact that writing "0" to the low byte of the
next higher register has no effect (only action is when writing "1"s).
Nonetheless, this cleans up the accesses so no bad side effects might occur
in the future, if execution order changes, or more bit fields get added to
CSR_INT_COALESCING.
Add some comments regarding periodic interrupt usage.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To support byte writes to CSR_INT_COALESCING and CSR_INT_PERIODIC registers,
add iwl_write8(), including debug/trace support.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We've accumulated a number of options for wiphys
which make more sense as flags as we keep adding
more. Convert the existing ones.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
cxgb3: fix premature page unmap
ibm_newemac: Fix EMACx_TRTR[TRT] bit shifts
vlan: Fix register_vlan_dev() error path
gro: Fix illegal merging of trailer trash
sungem: Fix Serdes detection.
net: fix mdio section mismatch warning
ppp: fix BUG on non-linear SKB (multilink receive)
ixgbe: Fixing EEH handler to handle more than one error
net: Fix the rollback test in dev_change_name()
Revert "isdn: isdn_ppp: Use SKB list facilities instead of home-grown implementation."
TI Davinci EMAC : Fix Console Hang when bringing the interface down
smsc911x: Fix Console Hang when bringing the interface down.
mISDN: fix error return in HFCmulti_init()
forcedeth: mac address fix
r6040: fix version printing
Bluetooth: Fix regression with L2CAP configuration in Basic Mode
Bluetooth: Select Basic Mode as default for SOCK_SEQPACKET
Bluetooth: Set general bonding security for ACL by default
r8169: Fix receive buffer length when MTU is between 1515 and 1536
can: add the missing netlink get_xstats_size callback
...
The entire aggregation code currently operates on the
hw pointer and station addresses, but that needs to
change to make stations purely per-vif; As one step
preparing for that make the aggregation code callable
with the station, or by the combination of virtual
interface and station address.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also regroup CSR_EEPROM and CSR_OTP bit field definitions.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using the new mac80211 functionality, this makes
iwlwifi handle unicast PS buffering correctly.
The device works like this:
* when a station goes to sleep, the microcode notices
this and marks the station as asleep
* when the station is marked asleep, the microcode
refuses to transmit to the station and rejects all
frames queued to it with the failure status code
TX_STATUS_FAIL_DEST_PS (a previous patch handled
this correctly)
* when we need to send frames to the station _although_
it is asleep, we need to tell the ucode how many,
and this is asynchronous with sending so we cannot
just send the frames, we need to wait for all other
frames to be flushed, and then update the counter
before sending out the poll response frames. This
is handled partially in the driver and partially in
mac80211.
In order to do all this correctly, we need to
* keep track of how many frames are pending for each
associated client station (avoid doing it for other
stations to avoid the atomic ops)
* tell mac80211 that we driver-block the PS status
while there are still frames pending on the queues,
and once they are all rejected (due to the dest sta
being in PS) unblock mac80211
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This field was marked as reserved before since we didn't
use it, but is present in all released firmwares afaict.
We're going to need it soon, so add it now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a frame is sent to a sleeping station, the
microcode reports TX_STATUS_FAIL_DEST_PS as its
status -- we need to translate that to the flag
that mac80211 expects.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Handle BSS_CHANGED_BEACON_ENABLED to enable the sending
of beacons. Also set the correct HT RXON and QoS config.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When sending beacon commands to the uCode, we must
inform it of the offset in the beacon frame of the
TIM Element so it can transmit packets from the
correct queue. This functionality is implemented
in iwl_set_beacon_tim().
Fix a bug setting the rate_n_flags for the beacon
packet. First, it should not use the station table's
rate (it's a management frame), and second it needs
to properly configure the TX antennas.
Finally, also, clean up and comment relevant functions.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A recent change optimized the power usage by the device by only powering it
up during EEPROM load if it is required (for OTP devices). This change causes
an error on the 1000 series devices during module load.
The error looks as follows:
[ 1624.024524] iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27kds
[ 1624.024527] iwlagn: Copyright(c) 2003-2009 Intel Corporation
[ 1624.024711] iwlagn 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1624.024749] iwlagn 0000:01:00.0: setting latency timer to 64
[ 1624.024909] iwlagn 0000:01:00.0: Detected Intel Wireless WiFi Link 1000 Series BGN REV=0x6C
[ 1624.081263] iwlagn 0000:01:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0x080003D8
[ 1624.092967] iwlagn 0000:01:00.0: OTP is empty
[ 1624.092988] iwlagn 0000:01:00.0: Unable to init EEPROM
[ 1624.093033] iwlagn 0000:01:00.0: PCI INT A disabled
[ 1624.093065] iwlagn: probe of 0000:01:00.0 failed with error -2
Adding a dump_stack() to where that error is printed shows the following:
[ 1624.024524] iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27kds
[ 1624.024527] iwlagn: Copyright(c) 2003-2009 Intel Corporation
[ 1624.024711] iwlagn 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1624.024749] iwlagn 0000:01:00.0: setting latency timer to 64
[ 1624.024909] iwlagn 0000:01:00.0: Detected Intel Wireless WiFi Link 1000 Series BGN REV=0x6C
[ 1624.081263] iwlagn 0000:01:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0x080003D8
[ 1624.081263] Pid: 3073, comm: work_for_cpu Tainted: G W 2.6.31.5 #4
[ 1624.081263] Call Trace:
[ 1624.081263] [<ffffffffa02395db>] T.726+0x22b/0x420 [iwlcore]
[ 1624.081263] [<ffffffffa023985a>] iwlcore_eeprom_acquire_semaphore+0x8a/0x190 [iwlcore]
[ 1624.081263] [<ffffffff81110c94>] ? __kmalloc+0x194/0x1c0
[ 1624.081263] [<ffffffffa02391f5>] ? iwlcore_eeprom_verify_signature+0x25/0xf0 [iwlcore]
[ 1624.081263] [<ffffffffa0239c67>] iwl_eeprom_init+0x107/0xf40 [iwlcore]
[ 1624.081263] [<ffffffffa026ab9c>] ? iwl_prepare_card_hw+0x11c/0x470 [iwlagn]
[ 1624.081263] [<ffffffff8127e2a4>] ? pci_bus_write_config_byte+0x64/0x80
[ 1624.081263] [<ffffffffa026b1f8>] iwl_pci_probe+0x308/0xac0 [iwlagn]
[ 1624.081263] [<ffffffff810710a0>] ? do_work_for_cpu+0x0/0x30
[ 1624.081263] [<ffffffff81284912>] local_pci_probe+0x12/0x20
[ 1624.081263] [<ffffffff810710b3>] do_work_for_cpu+0x13/0x30
[ 1624.081263] [<ffffffff81075826>] kthread+0xa6/0xb0
[ 1624.081263] [<ffffffff81012fea>] child_rip+0xa/0x20
[ 1624.081263] [<ffffffff81075780>] ? kthread+0x0/0xb0
[ 1624.081263] [<ffffffff81012fe0>] ? child_rip+0x0/0x20
[ 1624.092967] iwlagn 0000:01:00.0: OTP is empty
[ 1624.092988] iwlagn 0000:01:00.0: Unable to init EEPROM
[ 1624.093033] iwlagn 0000:01:00.0: PCI INT A disabled
[ 1624.093065] iwlagn: probe of 0000:01:00.0 failed with error -2
We know that the routines in this trace, iwlcore_eeprom_acquire_semaphore
and iwlcore_eeprom_verify_signature, only access CSR registers and thus do
not need the device to be awake if it is EEPROM. But for OTP it is required
for the device to be awake to read these registers. Ensure device is awake
before accessing these registers.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Align the format for tx_statistics and rx_statistics debugfs output for
better readability
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In both 6x00 and 6x50 series, the enhanced/extended tx power table in
EEPROM is used to set the max. tx power limit.
This new tx power table is in 1/2 dBm format, which creates an issue of
possibility of 1/2 dBm loss when driver set the tx power limit; because
of driver keep track and report the tx power in dBm format.
In order to prevent the 1/2 dBm loss, keep track of the true max tx
power in 1/2 dBm format in driver; do the comparison and adjust the tx
power if needed when send tx power command to uCode.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Power-saving logic will not re-issue a POWER_TABLE_CMD if a new command
matches the prior one. This can be bad if we re-start the device due to
e.g. uCode error; the new POWER_TABLE_CMD (required to invoke power-saving)
may match the prior POWER_TABLE_CMD issued before the uCode error.
Ensure the POWER_TABLE_CMD is sent to device when uCode is up.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
