Merge ENE UB6250 MS card codes from keucr to drivers/usb/storage/ene_ub6250.c.
Signed-off-by: Cho, Yu-Chen <acho@novell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds SuperSpeed descriptors to the
g_zero gadget.
The SuperSpeed descriptors were added both for
f_soursesink and f_loopback function drivers.
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Amit Blay <ablay@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add SuperSpeed descriptors to the Network USB
function drivers.
This has been lightly tested using a Linux host.
I was able to ssh from device to host and host to
device, no obvious problems seen.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The USB high speed device must support the TEST_MODE, but the driver
didn't support it. When we sent the SET_FEATURE for TEST_MODE to
the driver, the request was successful, but the module didn't enter
the TEST_MODE.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The USB high speed device must support the TEST_MODE, but the driver
didn't support it. When we sent the SET_FEATURE for TEST_MODE to
the driver, the request was successful, but the module didn't enter
the TEST_MODE.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
BUSWAIT is a 4-bit-wide value that controls the number of access waits
from the CPU to on-chip USB module. b'0000 inserts 0 wait (2 access
cycles) and b'1111 inserts 15 waits (17 access cycles, hardware
initial value), respectively.
BUSWAIT value depends on peripheral clock frequency supplied to on-chip
of each CPU, hence should be configurable through platform data.
Note that this patch assumes that b'0000 (0 wait, 2 access cycles) is
rerely used and considered as invalid. If valid 'buswait' data is not
provided by platform, initial b'1111 (15 waits, 17 access cycles) will
be applied as a safe default.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When we run rmmod a gadget driver, the driver will call
disable_controller(). Then, because the bit of USBE in SYSCFG0 was
cleared in on_chip=1 mode, we could not connect the usb when we run
insmod a gadget driver next time.
This patch also cleans up probe() and ->stop() about unnecessary
init_controller().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Restoring the missing INDEX register value in musb_restore_context().
Without this suspend resume functionality is broken with offmode
enabled.
Cc: stable@kernel.org
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Commit e534c5b831 (USB: fix regression
occurring during device removal) didn't go far enough. It failed to
take into account that when a driver claims multiple interfaces, it may
release them all at the same time. As a result, some interfaces can
get released before they are unregistered, and we deadlock trying to
acquire the bandwidth_mutex that we already own.
This patch (asl478) handles this case by setting the "unregistering"
flag on all the interfaces before removing any of them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Tested-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Both fusb300 and langwell udcs seem to only
work with 32-bit address space.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
- remove pointer u32 abuse in fusb300_fill_idma_prdtbl().
It is assigned the dma_addr to a pointer and then back.
Poor families may have to recycle variables but we don't
- don't free req.buf in error case. We don't do it in the
ok case so it is probably wrong to do it in error case.
- return in error case. There is no reason to continue
without data and performing ops on an invalid pointer.
- The if (d) statement is bogus since an invalid DMA pointer
is ~0 on some architecutres. And since we return for the
invalid case we don't need it.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix the following compile warning:
| usb/gadget/ci13xxx_udc.c: In function 'show_registers':
| usb/gadget/ci13xxx_udc.c:1242:1: warning: the frame size of 2064 bytes is larger than 1024 bytes
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes the following compile warnings:
drivers/usb/gadget/net2272.c: In function ‘net2272_kick_dma’:
drivers/usb/gadget/net2272.c:740:2: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 6 has type ‘dma_addr_t’ [-Wformat]
drivers/usb/gadget/net2272.c: In function ‘net2272_queue’:
drivers/usb/gadget/net2272.c:859:2: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 8 has type ‘dma_addr_t’ [-Wformat]
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes the following compile warnings:
drivers/usb/gadget/langwell_udc.c: In function ‘queue_dtd’:
drivers/usb/gadget/langwell_udc.c:596:2: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/usb/gadget/langwell_udc.c: In function ‘langwell_udc_probe’:
drivers/usb/gadget/langwell_udc.c:3274:2: warning: format ‘%d’ expects argument of type ‘int’, but argument 4 has type ‘size_t’ [-Wformat]
drivers/usb/gadget/langwell_udc.c:3289:2: warning: format ‘%d’ expects argument of type ‘int’, but argument 4 has type ‘size_t’ [-Wformat]
drivers/usb/gadget/langwell_udc.c: In function ‘langwell_udc_resume’:
drivers/usb/gadget/langwell_udc.c:3473:2: warning: format ‘%d’ expects argument of type ‘int’, but argument 4 has type ‘size_t’ [-Wformat]
drivers/usb/gadget/langwell_udc.c:3487:2: warning: format ‘%d’ expects argument of type ‘int’, but argument 4 has type ‘size_t’ [-Wformat]
Signed-off-by: Felipe Balbi <balbi@ti.com>
that code has been dead forever. Since the
first commit (0fe6f1d1) the use of that code
has been commented out. Let's drop the dead
code already and fix the following compile
warning:
| drivers/usb/gadget/fusb300_udc.c: At top level:
| drivers/usb/gadget/fusb300_udc.c:771:13: warning: ‘fusb300_wrfifo’ defined but not used [-Wunused-function]
| drivers/usb/gadget/fusb300_udc.c:1027:13: warning: ‘fusb300_set_ep_bycnt’ defined but not used [-Wunused-function]
Signed-off-by: Felipe Balbi <balbi@ti.com>
The autosuspend function can be disabled by unchecking the Macro
CONFIG_REALTEK_AUTOPM in kernel config file, by default, this macro is
turned on.
Signed-off-by: edwin_rong <edwin_rong@realsil.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is a bug in Samsung's UDC driver, which is completely disabling
the USB device when a custom UDC command is used.
Following patch seems to get the right behavior (e.g. enabling pull-up
instead of disabling then Vcc is applied).
Signed-off-by: Viliam Mateicka <viliam.mateicka@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A compilation warning was added by the patch
"usb: gadget: use config_ep_by_speed() instead of ep_choose()".
This patch fixed it.
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
With this commit: cccad6d4b1
usb: otg: notifier: switch to atomic notifier
Following dumps are observed on attach/detach for MUSB HOST
mode and on a detach for MUSB Device mode.
BUG: sleeping function called from invalid context at kernel/mutex.c:85
where, the source is:
twl6030_usb_irq
->atomic_notifier_call_chain
->musb_otg_notifications
->twl6030_set_vbus
->twl_i2c_write_u8
->mutex_lock
This patch moves the i2c writes in set_vbus function to a
work-queue thereby avoiding I2C writes in atomic context.
Tested HOST and Device mode functionality on OMAP4460
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The recent commit 2edb11cbac fixed req->length in the composite_setup()
function, but that will cause all g_zero tests to fail like:
root#> ./testusb -D /proc/bus/usb/002/021 -t14 -c 15000 -s 256 -v 1
unknown speed /proc/bus/usb/002/021
/proc/bus/usb/002/021 test 14 --> 32 (Broken pipe)
We need to fix req->length in sourcesink_setup() as well to avoid this.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since printk_ratelimit() shouldn't be used anymore (see comment in
include/linux/printk.h), replace it with printk_ratelimited()
Signed-off-by: Manuel Zerpies <manuel.f.zerpies@ww.stud.uni-erlangen.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since printk_ratelimit() shouldn't be used anymore (see comment in
include/linux/printk.h), replace it with printk_ratelimited()
Signed-off-by: Manuel Zerpies <manuel.f.zerpies@ww.stud.uni-erlangen.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since printk_ratelimit() shouldn't be used anymore (see comment in
include/linux/printk.h), replace it with printk_ratelimited()
Signed-off-by: Manuel Zerpies <manuel.f.zerpies@ww.stud.uni-erlangen.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
dev_get_drvdata() is exactly the same as
platform_get_drvdata(). Drop that useless
access to the platform device.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This was somehow forgotten.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
bind() and pull is moved to udc core, call callbacks are verified by the
upper layer.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
udc-core checks for valid callbacks so there is no need for the driver
to do so. Also "can-be-bound-once" is verified by udc-core. The pull-up
callback is called by udc-core afterwords.
[ balbi@ti.com : keep holding gadget_driver pointer for now
remove the stupid check for gadget_driver otherwise
we don't handle IRQs ]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
udc_start() should only trigger the internal state machine and make
minimal house keeping. Before that call udc-core calls the bind()
callback and after the callback the pullup().
udc_stop() is simillar, udc-core calls pullup(), unbind() and finally
udc_stop().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The configuration is static however we only know the speed after we have
connected with the other side.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This value is now assigned during bind(). The configuration depends on
static values assigned by dummy driver itself. So there is no need to
defer this assigment until one know the actuall speed since the
configuration is static and known early.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is only required to be done once. There is no counter part to this
in ->stop() so there is no need to re-do it next time. While here also
init the max_stream size to 0 on SS speed.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
maxpacket is set by the udc driver for ep0 very early. This value is
copied by the function gadget used later for the USB_DT_DEVICE and
USB_DT_DEVICE_QUALIFIER query. This seems to work fine so far. For USB3
we need set a different value here. In SS speed it is 2^x with x=9 and
in HS we set something <= 64. If the UDC starts in SS and continues in
HS after the cable has been plugged it will report a too small value.
There setting of this value is defered and taken automaticly from the
ep0 pointer where the UDC driver can update it according to the speed it
detected _after_ a cable has been plugged.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
now that we have the udc class, we can allow
multiple gadget controller drivers to be
compiled as modules. This will allow for
distro-like kernels for embedded devices.
With this patch, I managed to build an x86
kernel with support for many of the controllers
enabled:
CONFIG_USB_FUSB300=m
CONFIG_USB_R8A66597=m
CONFIG_USB_M66592=m
CONFIG_USB_AMD5536UDC=m
CONFIG_USB_CI13XXX_PCI=m
CONFIG_USB_NET2272=m
CONFIG_USB_NET2280=m
CONFIG_USB_GOKU=m
CONFIG_USB_LANGWELL=m
CONFIG_USB_EG20T=m
Also an ARM kernel with support for many controllers:
CONFIG_USB_FUSB300=m
CONFIG_USB_OMAP=m
CONFIG_USB_R8A66597=m
CONFIG_USB_GADGET_MUSB_HDRC=m
CONFIG_USB_M66592=m
CONFIG_USB_NET2272=m
CONFIG_USB_DUMMY_HCD=m
The next step would be to get rid of the
direct access to arch/ and mach/ directories
on some gadget controllers so that we can
build all of them without depending on their
respective ARCH_* symbols.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When we start building glue layers as modules,
we need to be careful with the fifo_mode changes
otherwise that weird ifdeferry won't evaluate
correctly. Add the missing _MODULE variants for
all glue layers to prevent everybody from using
fifo_mode 2.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the MUSB IP is always OTG, so there's no point
in adding so many ifdefs on the code. Drop those
and always compile the driver for OTG support.
This also allows us to drop the useless "driver
mode" choice. For doing that, we need to make
musb depend on both Host and Peripheral side.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
if we have more endpoints configured than
enabled on fifo_mode, then we need to be
careful on save/restore context operations,
otherwise we will try to access uninitialized
__iomem pointer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This function has no user in my tree. It looks like it belongs to
net2280 but it somehow morphed into the dummy_hcd. So I remove it
before it spreads into more drivers.
After some digging I figured out that the only user was removed in
|commit 9079e91b5b
|Author: David Brownell <david-b@pacbell.net>
|Date: Wed May 7 16:00:36 2008 -0700
|
| USB: serial gadget: cleanup/reorg
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Taking the correct struct once avoids doing the speed dance.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
gadget_to_dummy_hcd() already does the speed check, so
it's unnecessary to unroll that all the time.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Before commit 53832daea ("usb: gadget: dummy_hcd: use the shared_hcd
infrastructure") the is_otg field was set in dummy_udc_probe(). It seems
to me that this field is used in gadget's bind function. Therefore I'm
moving it before the bind() callback is called.
Cc: Tatyana Brokhman <tlinder@codeaurora.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The removed code does the same thing as dummy_pullup(). The only
difference is that in dummy_udc_stop() the first dummy_pullup()
did not call usb_hcd_poll_rh_status().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the gadget controller number is only used
during bind() to update descriptors and/or
check that a particular controller can support
a particular gadget driver.
Because of that, we can remove the ifdef
trickery as it's a rather small optimization
anyway.
While at that, also sort the entries
alphabetically and add a comment stating we
want to keep the list ordered alphabetically.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 72c973d (usb: gadget: add usb_endpoint_descriptor
to struct usb_ep) has introduced a compile error to
ci13xxx_udc. Fix it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This also fixes the error path: If the second device fails to register
we never remove the first one.
This is compile-tested only. I don't see any difference between those
two. Maybe we should just use one name instead?
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Without it udev won't be able to load the driver once it notices the
device unbound.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In case pci_register_driver() fails it error will be 0 in case
platform_driver_register() was fine. Also without PCI
pci_register_driver() evaluates to 1 which is well, special. If
platform_driver_register() returns EINVAL or EBUSY we end up with 0.
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a new module parameter to dummy_hcd
called is_high_speed.
When set to false the connected device will be forced
to operate in full-speed mode. By default, this parameter
is set to 'true'.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds SS support to the dummy hcd module.
It may be used to test SS device when no (SS) HW is
available.
USB 3.0 hub includes 2 hubs - one HS and one SS. This
patch adds support for a SS root hub in the dummy_hcd
module.
A new module parameter was added: is_super_speed. When
set to true, a SS root hub will also be registered and
the connected device will be enumerated over the SS
root hub. The default of this parameter is false.
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
[ balbi@ti.com : slight change to commit log
fixed one coding style issue ]
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is a preparation for adding SuperSpeed
support to dummy hcd.
It takes the master side fields out of the struct
dummy to a separate structure. The init process
was also modified to resemble the way it is
done by xHCI.
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
SuperSpeed USB has defined a new descriptor, called
the Binary Device Object Store (BOS) Descriptor. It
has also changed a bit the definition of SET_FEATURE
and GET_STATUS requests to add USB3-specific details.
This patch implements both changes to the Composite
Gadget Framework.
[ balbi@ti.com : slight changes to commit log
fixed a compile error on ARM ]
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This field is used by the Gadget drivers to specify
the maximum speed they support, meaning: the maximum
speed they can provide descriptors for.
The driver speed will be set in consideration of this
value.
[ balbi@ti.com : dropped the ifdeffery ]
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The "channel_program" member was renamed to "adjust_channel_params",
but the documentation wasn't updated.
Reported-by: Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1476) fixes a regression introduced by
fccf4e8620 (USB: Free bandwidth when
usb_disable_device is called). usb_disconnect() grabs the
bandwidth_mutex before calling usb_disable_device(), which calls down
indirectly to usb_set_interface(), which tries to acquire the
bandwidth_mutex.
The fix causes usb_set_interface() to return early when it is called
for an interface that has already been unregistered, which is what
happens in usb_disable_device().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 09ba0def (USB: fsl_udc_core: prepare for SoCs with
BE registers and descriptors) introduced build breakage
on ARM arch. Fix it by setting accessors using a static
inline function which is a nop when compiling the driver
for ARM arch.
Commit 2ea6698 (USB: fsl_udc_core: support device mode of
MPC5121E DR USB Controller) caused another breakage on ARM
by using flush_dcache_range(). Don't use it, convert to the
DMA API usage instead. USB2.0CV Halt Endpoint Test succeeds
on PPC. Tested both on ARM i.MX31 and mpc5121 PPC, also with
CONFIG_DMA_API_DEBUG enabled.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch defines necessary fields to support
streaming for USB3.0.
It implements a new function, called
usb_ep_autoconfig_ss(), to be used instead of the
existing usb_ep_autoconfig() when working in
SuperSpeed mode and there is a need to search for
an endpoint according to the number of required
streams.
[ balbi@ti.com : slight changes to commit log ]
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
fix the coding style of a few switches on the
gadget framework.
[ balbi@ti.com : add a commit log ]
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
MAINTAINERS: add myself as maintainer of USB/IP
usb: r8a66597-hcd: fix cannot detect low/full speed device
USB: ehci-ath79: fix a NULL pointer dereference
USB: Add new FT232H chip to drivers/usb/serial/ftdi_sio.c
usb/isp1760: Fix bug preventing the unlinking of control urbs
USB: Fix up URB error codes to reflect implementation.
xhci: Always set urb->status to zero for isoc endpoints.
xhci: Add reset on resume quirk for asrock p67 host
xHCI 1.0: Incompatible Device Error
USB: don't let errors prevent system sleep
USB: don't let the hub driver prevent system sleep
USB: change maintainership of ohci-hcd and ehci-hcd
xHCI 1.0: Force Stopped Event(FSE)
xhci: Don't warn about zeroed bMaxBurst descriptor field.
USB: Free bandwidth when usb_disable_device is called.
xhci: Reject double add of active endpoints.
USB: TI 3410/5052 USB Serial Driver: Fix mem leak when firmware is too big.
usb: musb: gadget: clear TXPKTRDY flag when set FLUSHFIFO
usb: musb: host: compare status for negative error values
Add config_ep_by_speed() to configure the endpoint
according to the gadget speed.
Using this function will spare the FDs from handling
the endpoint chosen descriptor.
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change usb_ep_enable() prototype to use endpoint
descriptor from usb_ep.
This optimization spares the FDs from saving the
endpoint chosen descriptor. This optimization is
not full though. To fully exploit this change, one
needs to update all the UDCs as well since in the
current implementation each of them saves the
endpoint descriptor in it's internal (and extended)
endpoint structure.
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
peripheral drivers are using usb_add_gadget()/usb_del_gadget() to
register/unregister to the udc-core.
The udc-core will take the first available gadget driver and attach
function driver which is calling usb_gadget_register_driver(). This is
the same behaviour we have right now.
Only dummy_hcd was tested, the others were compiled tested.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Anton Tikhomirov <av.tikhomirov@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Dan Carpenter <error27@gmail.com>
Cc: Darius Augulis <augulis.darius@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Pavankumar Kondeti <pkondeti@codeaurora.org>
Cc: Roy Huang <roy.huang@analog.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Cc: Xiaochen Shen <xiaochen.shen@intel.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Cc: Yuan-Hsin Chen <yhchen@faraday-tech.com>
Cc: cxie4 <cxie4@marvell.com>
Cc: linux-geode@lists.infradead.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this class will be used to abstract away several of the duplicated
operations scattered among the USB gadget controller drivers.
Later, we can add an atomic notifier to tell interested drivers about
what's happening with the controller. Notifications such as suspend,
resume, enumerated, etc. will be useful, at a minimum, for implementing
usb charger detection.
As part of the converting process usb_gadget_probe_driver() is no longer
part of each udc but pushed into the ->stap() callback. The same for his
couterpart.
The core is currently set explicit to 'n'. It will be changed to 'y' once
all users are converted since it provides functions which clash with
other drivers.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This controller can control "Transaction Translators", but
the hcd->has_tt is not set.
Since the commit d199c96d41
("USB: prevent buggy from crashing the USB stack") has checked it,
the driver could not work the low/full speed device.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Loading the ehci-hcd module on the ath79 platform causes
a NULL pointer dereference:
CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == c0252928, ra == c00de968
Oops[#1]:
Cpu 0
$ 0 : 00000000 00000070 00000001 00000000
$ 4 : 802cf870 0000117e ffffffff 8019c7bc
$ 8 : 0000000a 00000002 00000001 fffffffb
$12 : 8026ef20 0000000f ffffff80 802dad3c
$16 : 8077a2d4 8077a200 c00f3484 8019ed84
$20 : c00f0000 00000003 000000a0 80262c2c
$24 : 00000002 80079da0
$28 : 80788000 80789c80 80262b14 c00de968
Hi : 00000000
Lo : b61f0000
epc : c0252928 __mod_vermagic5+0xc260/0xc7e8 [ehci_hcd]
Not tainted
ra : c00de968 usb_add_hcd+0x2a4/0x858 [usbcore]
Status: 1000c003 KERNEL EXL IE
Cause : 00800008
BadVA : 00000000
PrId : 00019374 (MIPS 24Kc)
Modules linked in: ehci_hcd(+) pppoe pppox ipt_REJECT xt_TCPMSS ipt_LOG
xt_comment xt_multiport xt_mac xt_limit iptable_mangle iptable_filte
r ip_tables xt_tcpudp x_tables ppp_async ppp_generic slhc ath mac80211
usbcore nls_base input_polldev crc_ccitt cfg80211 compat input_core a
rc4 aes_generic crypto_algapi
Process insmod (pid: 379, threadinfo=80788000, task=80ca2180,
tls=77fe52d0)
Stack : c0253184 80c57d80 80789cac 8077a200 00000001 8019edc0 807fa800 8077a200
8077a290 c00f3484 8019ed84 c00f0000 00000003 000000a0 80262c2c c00de968
802d0000 800878cc c0253228 c02528e4 c0253184 80c57d80 80bf6800 80ca2180
8007b75c 00000000 8077a200 802cf830 802d0000 00000003 fffffff4 00000015
00000348 00000124 800b189c c024bb4c c0255000 801a27e8 c0253228 c02528e4
...
Call Trace:
[<c0252928>] __mod_vermagic5+0xc260/0xc7e8 [ehci_hcd]
It is caused by:
commit c430131a02
Author: Jan Andersson <jan@gaisler.com>
Date: Tue May 3 20:11:57 2011 +0200
USB: EHCI: Support controllers with big endian capability regs
The two first HC capability registers (CAPLENGTH and HCIVERSION)
are defined as one 8-bit and one 16-bit register. Most HC
implementations have selected to treat these registers as part
of a 32-bit register, giving the same layout for both big and
small endian systems.
This patch adds a new quirk, big_endian_capbase, to support
controllers with big endian register interfaces that treat
HCIVERSION and CAPLENGTH as individual registers.
Signed-off-by: Jan Andersson <jan@gaisler.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The reading of the HC capability register has been moved by that
commit to a place where the ehci->caps field is not initialized
yet. This patch moves the reading of the register back to the
original place.
Acked-by: Jan Andersson <jan@gaisler.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
appended patch adds support for the new FTDI FT232H chip. This chip is a
single channel version of the dual FT2232H/quad FT4232H, coming with it's
own default PID 0x6014 (FT2232H uses the same PID 0x6010 like FT2232C,
FT4232H has also it's own PID).
The patch was checked on an UM232H module and a terminal program with TX/RX
shorted to that typing in the terminal reproduced the characters.
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Both control and bulk transfers use isp1760 slots of type ATL, but the
driver unlink code for ATL slots only acts on urbs describing a bulk
transfer, letting the code for INT slots take care of the unlink instead,
which often ended up removing the interrupt transfer for root hub events
instead. That's not good, and gets fixed by this patch.
Signed-off-by: Arvid Brodin <arvid.brodin@enea.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-usb-linus' of git+ssh://master.kernel.org/pub/scm/linux/kernel/git/sarah/xhci:
USB: Fix up URB error codes to reflect implementation.
xhci: Always set urb->status to zero for isoc endpoints.
xhci: Add reset on resume quirk for asrock p67 host
xHCI 1.0: Incompatible Device Error
xHCI 1.0: Force Stopped Event(FSE)
xhci: Don't warn about zeroed bMaxBurst descriptor field.
USB: Free bandwidth when usb_disable_device is called.
xhci: Reject double add of active endpoints.
Remove linux/mm.h inclusion from netdevice.h -- it's unused (I've checked manually).
To prevent mm.h inclusion via other channels also extract "enum dma_data_direction"
definition into separate header. This tiny piece is what gluing netdevice.h with mm.h
via "netdevice.h => dmaengine.h => dma-mapping.h => scatterlist.h => mm.h".
Removal of mm.h from scatterlist.h was tried and was found not feasible
on most archs, so the link was cutoff earlier.
Hope people are OK with tiny include file.
Note, that mm_types.h is still dragged in, but it is a separate story.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch (as1473) renames the "in_suspend" field in struct
dev_pm_info to "is_prepared", in preparation for an upcoming change.
The new name is more descriptive of what the field really means.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: stable@kernel.org
Many stupid corrections of duplicated includes based on the output of
scripts/checkincludes.pl.
Signed-off-by: Vitaliy Ivanov <vitalivanov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When the xHCI driver encounters a Missed Service Interval event for an
isochronous endpoint ring, it means the host controller skipped over
one or more isochronous TDs. For TD that is skipped, skip_isoc_td() is
called. This sets the frame descriptor status to -EXDEV, and also sets
the value stored in the int pointed to by status to -EXDEV.
If the isochronous TD happens to be the last TD in an URB,
handle_tx_event() will use the status variable to give back the URB to
the USB core. That means drivers will see urb->status as -EXDEV.
It turns out that EHCI, UHCI, and OHCI always set urb->status to zero for
an isochronous urb, regardless of what the frame status is. See
itd_complete() in ehci-sched.c:
} else {
/* URB was too late */
desc->status = -EXDEV;
}
}
/* handle completion now? */
if (likely ((urb_index + 1) != urb->number_of_packets))
goto done;
/* ASSERT: it's really the last itd for this urb
list_for_each_entry (itd, &stream->td_list, itd_list)
BUG_ON (itd->urb == urb);
*/
/* give urb back to the driver; completion often (re)submits */
dev = urb->dev;
ehci_urb_done(ehci, urb, 0);
ehci_urb_done() completes the URB with the status of the third argument, which
is always zero in this case.
It turns out that many USB webcam drivers, such as uvcvideo, cannot
handle urb->status set to a non-zero value. They will not resubmit
their isochronous URBs in that case, and userspace will see a frozen
video.
Change the xHCI driver to be consistent with the EHCI and UHCI driver,
and always set urb->status to 0 for isochronous URBs.
This patch should be backported to kernels as old as 2.6.36
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: "Xu, Andiry" <Andiry.Xu@amd.com>
Cc: stable@kernel.org
The asrock p67 xhci controller completely dies on resume, add a
quirk for this, to bring the host back online after a suspend.
This should be backported to stable kernels as old as 2.6.37.
Signed-off-by: Maarten Lankhorst <m.b.lankhorst@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
It is one new TRB Completion Code for the xHCI spec v1.0.
Asserted if the xHC detects a problem with a device that does not allow it to
be successfully accessed, e.g. due to a device compliance or compatibility
problem. This error may be returned by any command or transfer, and is fatal
as far as the Slot is concerned. Return -EPROTO by urb->status or frame->status
of ISOC for transfer case. And return -ENODEV for configure endpoint command,
evaluate context command and address device command if there is an incompatible
Device Error. The error codes will be sent back to the USB core to decide how
to do. It's unnecessary for other commands because after the three commands run
successfully means that the device has been accepted.
Signed-off-by: Alex He <alex.he@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch (as1471) deprecates the File-backed Storage Driver and
schedules its replacement for the 3.8 kernel release (about two years
from now). Users are advised to switch to the Mass Storage Gadget
instead.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1464) implements the recommended policy that most errors
during suspend or hibernation should not prevent the system from going
to sleep. In particular, failure to suspend a USB driver or a USB
device should not prevent the sleep from succeeding:
Failure to suspend a device won't matter, because the device will
automatically go into suspend mode when the USB bus stops carrying
packets. (This might be less true for USB-3.0 devices, but let's not
worry about them now.)
Failure of a driver to suspend might lead to trouble later on when the
system wakes up, but it isn't sufficient reason to prevent the system
from going to sleep.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1465) continues implementation of the policy that errors
during suspend or hibernation should not prevent the system from going
to sleep.
In this case, failure to turn on the Suspend feature for a hub port
shouldn't be reported as an error. There are situations where this
does actually occur (such as when the device plugged into that port
was disconnected in the recent past), and it turns out to be harmless.
There's no reason for it to prevent a system sleep.
Also, don't allow the hub driver to fail a system suspend if the
downstream ports aren't all suspended. This is also harmless (and
should never happen, given the change mentioned above); printing a
warning message in the kernel log is all we really need to do.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Following the loss of David Brownell, I volunteer to maintain the
ohci-hcd and ehci-hcd drivers. This patch (as1472) makes it official.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
FSE shall occur on the TD natural boundary. The software ep_ring dequeue pointer
exceed the hardware ep_ring dequeue pointer in these cases of Table-3. As a
result, the event_trb(pointed by hardware dequeue pointer) of the FSE can't be
found in the current TD(pointed by software dequeue pointer). What should we do
is to figured out the FSE case and skip over it.
Signed-off-by: Alex He <alex.he@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The USB 3.0 specification says that the bMaxBurst field in the SuperSpeed
Endpoint Companion descriptor is supposed to indicate how many packets a
SS device can handle before it needs to wait for an explicit handshake
from the host controller. A zero value means the device can only handle
one packet before it needs a handshake. Remove a warning in the xHCI
driver that implies this is an invalid value.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tanya ran into an issue when trying to switch a UAS device from the BOT
configuration to the UAS configuration via the bConfigurationValue sysfs
file. Before installing the UAS configuration, set_bConfigurationValue()
calls usb_disable_device(). That function is supposed to remove all host
controller resources associated with that device, but it leaves some state
in the xHCI host controller.
Commit 0791971ba8
usb: allow drivers to use allocated bandwidth until unbound
added a call to usb_disable_device() in usb_set_configuration(), before
the xHCI bandwidth functions were invoked. That commit fixed a bug, but
also introduced a bug that is triggered when a configured device is
switched to a new configuration.
usb_disable_device() goes through all the motions of unbinding the drivers
attached to active interfaces and removing the USB core structures
associated with those interfaces, but it doesn't actually remove the
endpoints from the internal xHCI host controller bandwidth structures.
When usb_disable_device() calls usb_disable_endpoint() with reset_hardware
set to true, the entries in udev->ep_out and udev->ep_in will be set to
NULL. Usually, when the USB core installs a new configuration,
usb_hcd_alloc_bandwidth() will drop all non-NULL endpoints in udev->ep_out
and udev->ep_in before adding any new endpoints. However, when the new
UAS configuration was added, all those entries were null, so none of the
old endpoints in the BOT configuration were dropped.
The xHCI driver blindly added the UAS configuration endpoints, and some of
the endpoint addresses overlapped with the old BOT configuration
endpoints. This caused the xHCI host to reject the Configure Endpoint
command. Now that the xHCI driver code is cleaned up to reject a
double-add of active endpoints, we need to fix the USB core to properly
drop old endpoints in usb_disable_device().
If the host controller driver needs bandwidth checking support, make
usb_disable_device() call usb_disable_endpoint() with
reset_hardware set to false, drop the endpoints from the xHCI host
controller, and then call usb_disable_endpoint() again with
reset_hardware set to true.
The first call to usb_disable_endpoint() will cancel any pending URBs and
wait on them to be freed in usb_hcd_disable_endpoint(), but will keep the
pointers in udev->ep_out and udev->ep in intact. Then
usb_hcd_alloc_bandwidth() will use those pointers to know which endpoints
to drop.
The final call to usb_disable_endpoint() will do two things:
1. It will call usb_hcd_disable_endpoint() again, which should be harmless
since the ep->urb_list should be empty after the first call to
usb_disable_endpoint() returns.
2. It will set the entries in udev->ep_out and udev->ep in to NULL, and call
usb_hcd_disable_endpoint(). That call will have no effect, since the xHCI
driver doesn't set the endpoint_disable function pointer.
Note that usb_disable_device() will now need to be called with
hcd->bandwidth_mutex held.
This should be backported to kernels as old as 2.6.32.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Tanya Brokhman <tlinder@codeaurora.org>
Cc: ablay@codeaurora.org
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@kernel.org
While trying to switch a UAS device from the BOT configuration to the UAS
configuration via the bConfigurationValue file, Tanya ran into an issue in
the USB core. usb_disable_device() sets entries in udev->ep_out and
udev->ep_out to NULL, but doesn't call into the xHCI bandwidth management
functions to remove the BOT configuration endpoints from the xHCI host's
internal structures.
The USB core would then attempt to add endpoints for the UAS
configuration, and some of the endpoints had the same address as endpoints
in the BOT configuration. The xHCI driver blindly added the endpoints
again, but the xHCI host controller rejected the Configure Endpoint
command because active endpoints were added without being dropped.
Make the xHCI driver reject calls to xhci_add_endpoint() that attempt to
add active endpoints without first calling xhci_drop_endpoint().
This should be backported to kernels as old as 2.6.31.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Tanya Brokhman <tlinder@codeaurora.org>
Cc: stable@kernel.org
Sometimes the connection fail happen on renesas_usbhs.
This patch fix it up.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the size of the firmware exceeds TI_FIRMWARE_BUF_SIZE we'll leak 'fw_p'
by failing to call release_firmware().
This patch fixes the leak.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Several fixes as well where the +1 was missing.
Done via coccinelle scripts like:
@@
struct resource *ptr;
@@
- ptr->end - ptr->start + 1
+ resource_size(ptr)
and some grep and typing.
Mostly uncompiled, no cross-compilers.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fixes mis-use of MUSB's hardware feature where it won't
flush FIFOs when TXPKTRDY flag was set before and we are
flushing setting both FLUSHFIFO and TXPKTRDY.
In other words, we need to ensure that when we try to
flush FIFOs, we don't accidentaly set TXPKTRDY bit too
due to a read-back of the register.
The MUSB Programming Guide says "May be set simultaneously
with TxPktRdy to abort the packet that is currently being
loaded into the FIFO". This is a situation where TXPKTRDY
hasn't been set yet, but some data already loaded into the
fifo. It looks, that if TXPKTRDY has been set before, and
there is no loading in progress, but we set FLUSHFIFO with
the TXPKTRDY, controller tries to use the same logic to
abort loading and as the result just does nothing (because
there is no packet been loaded currently)
Signed-off-by: Yauheni Kaliuta <yauheni.kaliuta@nokia.com>
[ balbi@ti.com : fixed one whitespace git complained about
improved the commit log slightly ]
Signed-off-by: Felipe Balbi <balbi@ti.com>
Variable d is a struct usb_iso_packet_descriptor. The status filed is usually
negative when an error happens.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
