The hardware design requires that the driver avoid indicating
checksum offload success on some ipv6 frames with extension
headers.
The code needs to just check for the IPV6EXADD bit and if
it is set punt the checksum to the stack. I don't know why
the code was checking TCP on inner protocol, as that code
doesn't make any sense to me but seems wrong, so remove it.
Change-ID: I10d3aacdbb1819fb60b4b0eb80e6cc67ef2c9599
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This implements a state machine intended to support the userland tool for
updating the device eeprom. The state machine implements one-shot reads,
writes, multi-step write sessions, and checksum requests. If we're in the middle
of a multi-step write session, no one should fire off other writes, however, one
shot reads are valid. The userland tool is expected to keep track of its session
status, arrange the placement and ordering of the writes, and deal with the
checksum requirement.
This patch also adds nvmupdate support to ethtool callbacks.
The get_eeprom() and set_eeprom() services in ethtool are used here to
facilitate the userland NVMUpdate tool. The 'magic' value in the get and
set commands is used to pass additional control information for managing
the read and write steps.
The read operation works both as normally expected in the standard ethtool
method, as well as with the extra NVM controls. The write operation
works only for the expanded NVM functions - the normal ethtool method is
not allowed because of the NVM semaphore management needed for multipart
writes, as well as the checksum requirement.
Change-ID: I1d84a170153a9f437906744e2e350fd68fe7563d
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
spotted by cppcheck
Signed-off-by: Toralf Förster <toralf.foerster@gmx.de>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Display a verbose warning message when the incorrect PF attempts to
control timestamping for a port to which it was not assigned. This
shouldn't display except in the case of multiple PFs per port. The
primary intent of this message is to help debugging the reason why the
SIOCSHWTSTAMP ioctl has failed, and to help narrow the cause of the
issue.
Change-ID: Ic98798e0c844d98389d4c20e7160ba256f2bc7e8
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1. Remove some break statements that will never get touched.
2. Remove an extra space.
3. Remove a comment for a parameter that doesn't exist
4. Move the assignment of a variable up to get rid of an else case.
Change-ID: I308a4b5ec070b1f0601f13b041ba4375aaad4b06
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e has a single set of TX time stamping resources per NIC.
Use a simple bit lock to avoid race conditions and leaking skbs
when multiple TX rings try to claim time stamping.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
skb_tx_timestamp() does not report software time stamp
if SKBTX_IN_PROGRESS is set. According to timestamping.txt
software time stamps are a fallback and should not be
generated if hardware time stamp is provided.
Move call to skb_tx_timestamp() after setting
SKBTX_IN_PROGRESS.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a new API to get the port mac address from firmware.
It also adds support to the ndo_get_phys_port_id() callback to provide
port specific unique id to the netdev layer.
If the adapter has a valid per-port mac address then that
would be used for this purpose and is expected to be unique
on a per-port basis.
The information can be viewed by reading the phys_port_id
attribute in sysfs for each netdev or via IF netlink
interface.
Change-ID: I341fa6fff9c112f1f6d987189309e730e0b50e8b
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Dumping a bridge fdb dumps every fdb entry
held. With this change we are going to filter
on selected bridge port.
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump.
Change-ID: Ie0c36583ffd9997679f46bdf89bc462d3e992995
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement set_settings for ethtool in i40e.
Change-ID: Ie3c3fe18e8ff86c3f25b842844b3d9aabc9bba57
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add i40e implementation of setpauseparam to ethtool.
Change-ID: Ie7766b2091ec8f934737573c9ffd426081966718
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add function set_fc to set the requested FC mode. This patch also
adds the init of FC setting to get_link_info and replaces the init
code to set FC off by default in main. Also adds i40e_set_phy_config
to support this.
Change-ID: I7b25bbaec81f15777137ab324a095f916e44351d
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Just move nway reset up, will be used in the next patch.
Change-ID: Ice3b631fa2044debc5c4541b42872a48163f8452
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a new variable, hw.phy.link_info.an_enabled, to track whether autoneg is
enabled. Also add a new function update_link_info that will update that
variable as well as calling get_link_info to update the rest of the link info.
Also add get_phy_capabilities to support this.
Change-ID: I5157ef03492b6dd8ec5e608ba0cf9b0db9c01710
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Finish the i40e implementation of get_settings for ethtool.
Change-ID: Iec81835aa9380723ae9288bcb79b30a6a1ecd498
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
TPH is not currently enabled in this product, make sure it
isn't enabled by default.
Change-ID: Ibb1a10799c33c4c76dec06fcd53b1d6efa13c1f5
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When turning off ntuple with a FD table full situation,
the driver would have auto disabled FD filter additions.
Clear the auto disable flag for FD_SB so that when the
feature is turned on again using "ethtool -K ethx ntuple on"
we can start adding filters once again.
Change-ID: I036a32e7331bcae765b657c8abb4fa070940b163
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the AQ interrupt gets lost for some reason, VF communications will
stall as the VFs have no way of reaching the PF, which is essentially
deaf. The VFs end up waiting forever for a reply that will never come.
To alleviate this condition, go ahead and check the ARQ every time we
run the service task. Remove the check for a pending event, and get rid
of a chatty error message that is now meaningless.
Change-ID: I0fc9d18169cd45c98f60188aef872cd6cee9a027
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Force a shifted '1' to be unsiged to avoid shifting a signed int
Change-ID: I688cbd082af0f2e1df548fda25847a5ca04babcf
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The HW still needs to consume it and freeing it in the function
that created it would mean we will be racing with the HW. The
i40e_clean_tx_ring() routine will free up the buffer attached once
the HW has consumed it. The clean_fdir_tx_irq function had to be fixed
to handle the freeing correctly.
Cases where we program more than one filter per flow (Ipv4), the
code had to be changed to allocate dummy buffer multiple times
since it will be freed by the clean routine. This also fixes an issue
where the filter program routine was not checking if there were
descriptors available for programming a filter.
Change-ID: Idf72028fd873221934e319d021ef65a1e51acaf7
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We don't need the export.h header so we can just go ahead and remove it.
Change-ID: I9057396b141ee449d8299409081358b9270a7c4d
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Prevent writing to reserved bits, queue index is 0-127
Change-ID: Ic923e1c92012a265983414acd8f547c4bdac2e34
Signed-off-by: Christopher Pau <christopher.pau@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Driver needs to initialize all members of context descriptor. Stale
data is possible otherwise.
Change-ID: Idc6b53af45583509da42d5ec0824cbaf78aee64f
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With the auto_disable flags added there was a bug that was causing the
replay logic to not work correctly.
This patch fixes the issue so that we call a replay after a sideband
reset correctly.
Change-ID: I005fe1ac361188ee5b19517a83c922038cba1b00
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add new variable defining ASQ command write back timeout to allow for
dynamic modification of this timeout. Initialize it on AQ initialize
routine with default value, vary it on device ID.
Change-ID: I5c9908f9d7c5455634353b694a986d6f146d1b9d
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make mask value of all 1s. Value of -1 can't be used for u32 type.
Change-ID: I49d58b77639939fe7447a229dbf1f4a1bf7419ce
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Per a recent HW designer comment, this code is for ripping through the
queues and interrupts to fully disable them on driver init, specifically
to help clean up after a PXE or other early boot activity.
Change-ID: I32ed452021a1c2b06dace1969976f882a37b9741
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clear the AQ BAH and BAL registers on a clean shutdown to help make sure
all is tidy when the driver is done.
Change-ID: I393e92680247daa52a8e00bab183213672d73578
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the Base Address High and Low to the admin queue struct to simplify
another bit of "which context" logic in the config routines.
Change-ID: Iae195a7da3baffc1a9d522119e1e2b427068ad07
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There were a couple of fields in the fdir descriptor setup that
were not being reprogrammed, which left the opportunity for stale
data to be pushed as part of the descriptor next time it was used.
Change-ID: Ieee5c96a7d4713d469693f086c4854de949a7633
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
"fd current cnt" can be used to print the total filters consumed
by this interface, this includes guaranteed and best effort filters.
Change-ID: I2c417810c4999ce1388d2ea26f8e69679ba33966
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Hardware does not have a way of telling a PF how much of the global
shared FD table space is still available or is consumed.
Previously, every PF but PF0 would think there was still space available
when there wasn't. The PFs would continue to try to add filters and fail.
With this new logic if a filter programming error is detected we just
check if we are close to the guaranteed space full and that can be used
as a hint to say, there might not be space and we should turn off the
features. This way we can turn off the feature in SW for all PFs in
time.
Change-ID: I725cb2fab16c033f883056362b4542c1400503c5
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There wasn't a need to play the logic twice, it seems
like a left over from when we had to add two PTYPEs for
one filter. There should be no change in the number of
filters that actually got added to the hardware.
Change-ID: I5071d02eafd020b60e30eb96219f110f334eec85
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently every time we run through the i40e_ptp_init routine, we create
a new device node. This function is called by i40e_reset_and_rebuild
which is used to handle reset of the device. Even though the 1588
registers only get cleared on a GLOBAL reset, this function is still
called to handle a CORE reset.
This causes a leak of PTP device nodes at every reset. To fix this,
break PTP device clock node creation out of i40e_ptp_init, and only call
this if we don't already have a device created. Further invocation of
i40e_ptp_init will not generate new PTP devices. Instead, only the
necessary work required to reconfigure 1588 will be done.
This change also fixes an issue where a reset can cause the
device to forget it's timestamp configuration, and revert to the default
mode.
Change-ID: I741d01c61d9fe1d24887859d1316e1a8a892909e
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch prevents the SIOCGHWTSTAMP ioctl from possibly returning bad
data, by not permanently storing the setting into the private
structure until after we've finished validating that we can support it.
Change-ID: Ib59f9b4f73f451d5a2e76fb8efa5d4271b218433
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch facilitates future work by breaking the PTP hardware control
bits out of the i40e_set_ts_config function. By doing this, we can
maintain state about the 1588 timestamping mode and properly re-enable
to the last known mode during a re-initialize of 1588 bits.
This patch also modifies i40e_ptp_init to call the
i40e_ptp_set_timestamp_mode during the reconfiguration process. A
future patch will ensure that the hwtstamp_config structure is not reset
during this process, so that timestamp mode will be maintained across a
reset.
Change-ID: Ic20832c96c5c512ac203b6c7534e10d891c560f0
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reduces possible confusion and ambiguity in purpose of the ancillary
feature control entry point function.
Change-ID: I21d773c1a86878f6d061505185b596c788d1b7cc
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix HMC handling for big endian architectures.
Change-ID: Id8c46fc341815d47bfe0af8b819f0ab9a1e9e515
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We do not need to acquire NVM for Shadow RAM XSUM calculation, as we only
read from SR through SRCTL register for which having the ownership is not
required.
Change-ID: Ie238a8f09917d1d25f24cc7cec271951ac7b98f2
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a Tx hang happens, usually the Tx queue disable fails. At
this point if we try to recover by a VSI reinit the HW gets
unhappy and we get a Malicious Driver Detect (MDD) event.
HW expects a PF reset if a queue disable fails, if we don't do a PF
reset and restart the queue we get an MDD. This patch makes sure we
do a PF reset on Tx hang and that way we avoid any MDD because of Tx
queue disable failure.
Change-ID: I665ab6223577c788da857ee2132e733dc9a451e4
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The PF reset to clean up at the end of the remove is a nice thing
to do, but it also removes any LAA setting that Wake On LAN wants
for future wake up.
Change-ID: Ic090ec714df2d722281d11735cf75f2aa4432e2c
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The LAA is lost on a reset, so be sure to replay it when rebuilding
the switch after any reset.
Change-ID: I6e643f9a59dfd899b6cbdf84d93b4bc9c37bb949
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't short-circuit the LAA assignment when the driver thinks it has
already been done - it is possible that the user might want to force
the address setting again. At the same time, this requires a little
re-ordering of the filter management.
Change-ID: Ia0d71e3bc04edd7b68cf67edecc00abe7b9f6639
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure the Firmware sets up the LAA as a Wake-On-LAN address.
Change-ID: I57b9acd8c288424fcfed0911053eb725c400b41c
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ability is already there in the fw and this will make it easy
to toggle link without calling set_phy_config when no other link
settings need to change.
Change-ID: I185567ae81776382ac145247e4eb1ee95f22382c
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
One of the PCTYPES that was moved to a reserved value
wasn't removed from the code.
Change-ID: I31fafe6d79c5f5128179979af5eaafa8c0cd62fe
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
