Now that {cpu|edmac}_to_{edmac|cpu}() functions boiled down to the mere
{cpu|le32}_to_{le32|cpu}() calls, there's no need for these functions
anymore, so just get rid of them.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 71557a37ad ("[netdrvr] sh_eth: Add SH7619 support") added support
for the big-endian EDMAC descriptors. However, it was never used and never
worked right until the recent driver fixes. I think we now can just remove
this support, it was only burdening the driver from the start. It should be
easy to do without disturbing the SH platform code, at least for now...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 1299653aff ("sh_eth: fix descriptor access endianness") only
addressed the 32-bit buffer address field byte-swapping but the driver
still accesses 16-bit frame/buffer length descriptor fields without the
necessary byte-swapping -- which should affect the big-endian kernels.
In order to be able to use {cpu|edmac}_to_{edmac|cpu}(), we need to declare
the RX/TX descriptor word 1 as a 32-bit field and use shifts/masking to
access the 16-bit subfields (which gets rid of the ugly #ifdef'ery too)...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support of the fixed PHY.
This patch is based on commit 87009814cd ("ucc_geth: use the new fixed
PHY helpers").
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethernet AVB does not support 10 Mbps transfer speed.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver never calls cpu_to_edmac() when writing the descriptor address
and edmac_to_cpu() when reading it, although it should -- fix this.
Note that the frame/buffer length descriptor field accesses also need fixing
but since they are both 16-bit we can't use {cpu|edmac}_to_{edmac|cpu}()...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the little-endian SH771x kernels the driver has to byte-swap the RX/TX
buffers, however yet unset physcial address from the TX descriptor is used
to call sh_eth_soft_swap(). Use 'skb->data' instead...
Fixes: 31fcb99d99 ("net: sh_eth: remove __flush_purge_region")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3365711df0 ("sh_eth: WARN on access to a register not implemented in
in a particular chip") added WARN_ON() to sh_eth_{read|write}(), thus making
it unacceptable for these functions to be *inline* anymore. Remove *inline*
and move the functions from the header to the driver itself. Below is our
code economy with ARM gcc 4.7.3:
$ size drivers/net/ethernet/renesas/sh_eth.o{~,}
text data bss dec hex filename
32489 1140 0 33629 835d drivers/net/ethernet/renesas/sh_eth.o~
25413 1140 0 26553 67b9 drivers/net/ethernet/renesas/sh_eth.o
Suggested-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
AVB-DMAC Receive FIFO Warning interrupt is not enabled, so it is not
necessary to disable the interrupt in ravb_close().
On the other hand, this patch disables the interrupt in ravb_dmac_init() to
prevent the possibility that the interrupt is issued by the state that
a boot loader left.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the MDIO bitbang code consolidation, there's no need anymore for
bb_{set|clr}() as well as bb_read() -- just expand them inline, thus
saving more LoCs...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
sh_mm[cd]_ctrl() and sh_set_mdio() all look mostly the same -- factor out
their common code and put it into sh_mdio_ctrl().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO control bits are always mapped to the same bits of the same register
(PIR), so there's no need to store their masks in the 'struct bb_info'...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code reading the MAHR/MALR registers in read_mac_address() is terribly
ineffective -- it reads MAHR 4 times and MALR 2 times, while it's enough to
read each register only once. Use the local variables to achieve that,
somewhat beautifying the code while at it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code reading the MAHR/MALR registers in ravb_read_mac_address() is
terribly ineffective -- it reads MAHR 4 times and MALR 2 times, while
it's enough to read each register only once. Use the local variables to
achieve that, somewhat beautifying the code while at it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Rx queue #1 frame error counter name contains trailing underscore,
probably due to a typo...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a low memory situation the following kernel oops occurs:
Unable to handle kernel NULL pointer dereference at virtual address 00000050
pgd = 8490c000
[00000050] *pgd=4651e831, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] PREEMPT ARM
Modules linked in:
CPU: 0 Not tainted (3.4-at16 #9)
PC is at skb_put+0x10/0x98
LR is at sh_eth_poll+0x2c8/0xa10
pc : [<8035f780>] lr : [<8028bf50>] psr: 60000113
sp : 84eb1a90 ip : 84eb1ac8 fp : 84eb1ac4
r10: 0000003f r9 : 000005ea r8 : 00000000
r7 : 00000000 r6 : 940453b0 r5 : 00030000 r4 : 9381b180
r3 : 00000000 r2 : 00000000 r1 : 000005ea r0 : 00000000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c53c7d Table: 4248c059 DAC: 00000015
Process klogd (pid: 2046, stack limit = 0x84eb02e8)
[...]
This is because netdev_alloc_skb() fails and 'mdp->rx_skbuff[entry]' is left
NULL but sh_eth_rx() later uses it without checking. Add such check...
Reported-by: Yasushi SHOJI <yashi@atmark-techno.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/renesas/ravb_main.c
kernel/bpf/syscall.c
net/ipv4/ipmr.c
All three conflicts were cases of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add fallback compatibility strings for R-Car Gen 2 & 3 SoC Families.
This is in keeping with the fallback scheme being adopted wherever appropriate
for drivers for Renesas SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes PTP support active in CONFIG mode on R-Car Gen3.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 3d7608e4c1 ("ARM: shmobile: bockw: remove legacy
board file and config"), R-Car Gen1 SoCs are only supported in generic
DT-only ARM multi-platform builds. The driver doesn't need to match
platform devices by name anymore, hence remove the corresponding
platform_device_id entry.
Protect sh_eth_set_rate_r8a777x() and r8a777x_data by #ifdef CONFIG_OF,
as they're now referenced on DT platforms only.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 1fa59bda21 ("ARM: shmobile: Remove legacy board code
for Armadillo-800 EVA"), r8a7740 is only supported in generic DT-only
ARM multi-platform builds. The driver doesn't need to match platform
devices by name anymore, hence remove the corresponding
platform_device_id entry.
Protect r8a7740_data by #ifdef CONFIG_OF as it's now referenced on DT
platforms only. Move it to a more logical position, in front of the
r8a777x support, so we can have a single #ifdef covering all r7s* and
r8a* support soon. This requires moving a few helper functions, too.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit a483dcbfa2 ("ARM: shmobile: lager: Remove legacy
board support"), R-Car Gen2 SoCs are only supported in generic DT-only
ARM multi-platform builds. The driver doesn't need to match platform
devices by name anymore, hence remove the corresponding
platform_device_id entry.
Protect r8a779x_data by #ifdef CONFIG_OF as it's now referenced on DT
platforms only.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 05104c266a ("ARM: shmobile: r7s72100: genmai: Remove
legacy board file"), r7s72100 is only supported in generic DT-only ARM
multi-platform builds. The driver doesn't need to match platform
devices by name anymore, hence remove the corresponding
platform_device_id entry.
Protect r7s72100_data by #ifdef CONFIG_OF as it's now referenced on DT
platforms only. Move it to a more logical position, in front of the
r8a777x support, so we can have a single #ifdef covering all r7s* and
r8a* support soon. This requires moving a helper function, too.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GTI.TIV may be set to 2GHz^2 / rate, where rate is
that of the clock of the device. Rather than assuming a
rate of 130MHz use the actual rate of the clock.
The motivation for this is to use the correct rate on
the r8a7795/Salvator-X which is advertised as 133MHz but
may differ depending on the extal present on the Salvator-X.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the R8A7795 support was added to the driver, little attention was paid
to the ravb_open() error path: free_irq() for the EMAC interrupt was called
uncoditionally, unlike request_irq(), and in a wrong order as well...
As a result, on the R-Car gen2 SoCs I started getting the following in case
of a device opening error:
WARNING: CPU: 0 PID: 1 at kernel/irq/manage.c:1448 __free_irq+0x8c/0x228()
Trying to free already-free IRQ 0
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.4.0-rc1-dirty #1005
Hardware name: Generic R8A7791 (Flattened Device Tree)
Backtrace:
[<c0013818>] (dump_backtrace) from [<c00139b4>] (show_stack+0x18/0x1c)
r6:c063cdd6 r5:00000009 r4:00000000 r3:00204140
[<c001399c>] (show_stack) from [<c022a578>] (dump_stack+0x74/0x90)
[<c022a504>] (dump_stack) from [<c0025f04>] (warn_slowpath_common+0x8c/0xb8)
r4:ef04fd38 r3:c0714770
[<c0025e78>] (warn_slowpath_common) from [<c0025fd4>] (warn_slowpath_fmt+0x38/0x40)
r8:ee8ad800 r7:ef0030a0 r6:00000000 r5:00000000 r4:ef003040
[<c0025fa0>] (warn_slowpath_fmt) from [<c0064cc0>] (__free_irq+0x8c/0x228)
r3:00000000 r2:c063ce9f
[<c0064c34>] (__free_irq) from [<c0064ecc>] (free_irq+0x70/0xa4)
r10:0000016b r8:00000000 r7:00000000 r6:ee8ad800 r5:00000000 r4:ef003040
[<c0064e5c>] (free_irq) from [<c033472c>] (ravb_open+0x224/0x274)
r7:fffffffe r6:00000000 r5:fffffffe r4:ee8ad800
[<c0334508>] (ravb_open) from [<c041ac78>] (__dev_open+0x84/0x104)
r7:ee8ad830 r6:c0566334 r5:00000000 r4:ee8ad800
[<c041abf4>] (__dev_open) from [<c041af08>] (__dev_change_flags+0x94/0x13c)
r7:00001002 r6:00000001 r5:00001003 r4:ee8ad800
[<c041ae74>] (__dev_change_flags) from [<c041afe8>] (dev_change_flags+0x20/0x50)
r7:c072e6e0 r6:00000138 r5:00001002 r4:ee8ad800
[<c041afc8>] (dev_change_flags) from [<c06ec06c>] (ip_auto_config+0x174/0xfb8)
r8:00001002 r7:c072e6e0 r6:c0703344 r5:00000001 r4:ee8ad800 r3:00000101
[<c06ebef8>] (ip_auto_config) from [<c000a810>] (do_one_initcall+0x100/0x1cc)
r10:c06fb83c r9:00000000 r8:c06ebef8 r7:c0736000 r6:c0710918 r5:c0710918
r4:ef2f8f80
[<c000a710>] (do_one_initcall) from [<c06ccddc>] (kernel_init_freeable+0x11c/0x1
ec)
r10:c06fb83c r9:00000000 r8:0000009a r7:c0736000 r6:c0706bf0 r5:c06fb834
r4:00000007
[<c06cccc0>] (kernel_init_freeable) from [<c0514c54>] (kernel_init+0x14/0xec)
r10:00000000 r8:00000000 r7:00000000 r6:00000000 r5:c0514c40 r4:c0736000
[<c0514c40>] (kernel_init) from [<c0010458>] (ret_from_fork+0x14/0x3c)
r4:00000000 r3:ef04e000
Fix up the free_irq() call order and add a new label on the error path.
Fixes: 22d4df8ff3 ("ravb: Add support for r8a7795 SoC")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver does not handle the AVB-DMAC Receive FIFO Warning interrupt
now, so the interrupt should not be enabled.
Signed-off-by: Masaru Nagai <masaru.nagai.vx@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When RX/TX interrupt for Network Control queue and Best Effort queue
is issued at the same time, the interrupt mask of Network Control
queue will be reset when the mask of Best Effort queue is set.
This patch fixes this problem.
Signed-off-by: Masaru Nagai <masaru.nagai.vx@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
While the ring allocation is done by a single function, sh_eth_ring_init(),
the ring deallocation was split into two functions (almost always called
one after the other) for no good reason. Merge sh_eth_free_dma_buffer()
into sh_eth_ring_free() which allows us to save space not only on the
direct calls of the former function but also on the sh_eth_ring_init()'s
simplified error path...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'ret' local variable in sh_eth_ring_init() serves no useful purpose as
the only values it gets assigned are 0 and -ENOMEM both of which could be
returned directly...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7d7355f58b ("sh_eth: Ensure proper ordering of descriptor active
bit write/read") did the right thing but used too "heavy" barriers while
there were already "lighter" DMA barriers exactly for this case...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes in net/ipv4/ipmr.c, in 'net' we were
fixing the "BH-ness" of the counter bumps whilst in 'net-next'
the functions were modified to take an explicit 'net' parameter.
Signed-off-by: David S. Miller <davem@davemloft.net>
The correct name of the RX descriptor 0 bit 30 is RDLE (receive descriptor
list end), not RDEL.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This corrects what appear to be typos, making the code consistent with
itself, and allowing meaningful prefixes to be displayed with the errors in
question.
Before:
(null): failed to initialize MDIO
(null): Cannot allocate desc base address table (size 176 bytes)
After:
ravb e6800000.ethernet: failed to initialize MDIO
ravb e6800000.ethernet: Cannot allocate desc base address table (size 176 bytes)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
sh_eth_ring_free() called in the sh_eth_ring_init()'s error path expects
the arrays pointed to by 'sh_eth_private::[rt]x_skbuff' to be initialized
with NULLs but they are allocated with just kmalloc_array() and so are left
filled with random data. Use kcalloc() instead.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RX buffer size calulation failed to account for the length granularity
(which is now 32 bytes)...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both Renesas R-Car and RZ/A1 manuals state that RX buffer length must be
a multiple of 32 bytes, while the driver only uses 16 byte granularity...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch supports the r8a7795 SoC by:
- Using two interrupts
+ One for E-MAC
+ One for everything else
+ Both can be handled by the existing common interrupt handler, which
affords a simpler update to support the new SoC. In future some
consideration may be given to implementing multiple interrupt handlers
- Limiting the phy speed to 100Mbit/s for the new SoC;
at this time it is not clear how this restriction may be lifted
but I hope it will be possible as more information comes to light
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
[horms: reworked]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is in preparation for using this driver on arm64 where the
implementation of __dma_alloc_coherent fails if a device parameter is not
provided.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Masaru Nagai <masaru.nagai.vx@renesas.com>
[horms: squashed into a single patch]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver overrides the error returned by platform_get_irq() with -ENODEV
which e.g. precludes the deferred probing from working. Propagate the real
error code to the driver core instead.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver overrides the error returned by platform_get_irq() with -ENODEV
which e.g. precludes the deferred probing from working. Propagate the real
error code to the driver core instead.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Renesas Ethernet AVB controller requires that all data are aligned on 4-byte
boundary. While it's easily achievable for the RX data with the help of
skb_reserve() (we even align on 128-byte boundary as recommended by the manual),
we can't do the same with the TX data, and it always comes unaligned from
the networking core. Originally we solved it an easy way, copying all packet
to a preallocated aligned buffer; however, it's enough to copy only up to
3 first bytes from each packet, doing the transfer using 2 TX descriptors
instead of just 1. Here's an implementation of the new TX algorithm that
significantly reduces the driver's memory requirements.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/bridge/br_mdb.c
br_mdb.c conflict was a function call being removed to fix a bug in
'net' but whose signature was changed in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver is written as if it can adapt to a low memory situation allocating
less RX skbs and TX aligned buffers than the respective RX/TX ring sizes. In
reality though the driver would malfunction in this case. Stop being overly
smart and just fail in such situation -- this is achieved by moving the memory
allocation from ravb_ring_format() to ravb_ring_init().
We leave dma_map_single() calls in place but make their failure non-fatal
by marking the corresponding RX descriptors with zero data size which should
prevent DMA to an invalid addresses.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TCCR.TSRQn bit may get clearead after TCCR gets read, so that TCCR write
would get skipped. We don't need to check this bit before setting.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First, dma_sync_single_for_cpu() shouldn't have been called in the first place
(it's a streaming DMA API), dma_unmap_single() should have been called instead.
Second, dma_unmap_single() call after handing the buffer to napi_gro_receive()
makes little sense. Moreover desc->dptr might not be valid at this point.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the local variable intializers in the driver turned out to be pointless,
kill them.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to unlock before returning here.
Fixes: a0d2f20650 ('Renesas Ethernet AVB PTP clock driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This howto made sense in the 1990s when users had to manually configure
ISA cards with jumpers or vendor utilities, but with the implementation
of PCI it became increasingly less and less relevant, to the point where
it has been well over a decade since I last updated it. And there is
no value in anyone else taking over updating it either.
However the references to it continue to spread as boiler plate text
from one Kconfig file into the next. We are not doing end users any
favours by pointing them at this old document, so lets kill it with
fire, once and for all, to hopefully stop any further spread.
No code is changed in this commit, just Kconfig help text.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethernet AVB device includes the gPTP timer, so we can implement a PTP clock
driver. We're doing that in a separate file, with the main Ethernet driver
calling the PTP driver's [de]initialization and interrupt handler functions.
Unfortunately, the clock seems tightly coupled with the AVB-DMAC, so when that
one leaves the operation mode, we have to unregister the PTP clock... :-(
Based on the original patches by Masaru Nagai.
Signed-off-by: Masaru Nagai <masaru.nagai.vx@renesas.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethernet AVB includes an Gigabit Ethernet controller (E-MAC) that is basically
compatible with SuperH Gigabit Ethernet E-MAC. Ethernet AVB has a dedicated
direct memory access controller (AVB-DMAC) that is a new design compared to the
SuperH E-DMAC. The AVB-DMAC is compliant with 3 standards formulated for IEEE
802.1BA: IEEE 802.1AS timing and synchronization protocol, IEEE 802.1Qav real-
time transfer, and the IEEE 802.1Qat stream reservation protocol.
The driver only supports device tree probing, so the binding document is
included in this patch.
Based on the original patches by Mitsuhiro Kimura.
Signed-off-by: Mitsuhiro Kimura <mitsuhiro.kimura.kc@renesas.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The statistics registers have write-clear behaviour, which means we
will lose any increment between the read and write. Mitigate this by
only clearing when we read a non-zero value, so we will never falsely
report a total of zero. This also saves time as we only handle
error statistics here and they won't often be incremented.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are many different sets of registers implemented by the
different versions of this controller, and we can only expect this to
get more complicated in future. Limit how much ethtool needs to know
by including an explicit bitmap of which registers are included in the
dump, allowing room for future growth in the number of possible
registers.
As I don't have datasheets for all of these, I've only included
registers that are:
- defined in all 5 register type arrays, or
- used by the driver, or
- documented in the datasheet I have
Add one new capability flag so we can tell whether the RTRATE
register is implemented.
Delete the TSU_ADRL0 and TSU_ADR{H,L}31 definitions, as they weren't
used and the address table is already assumed to be contiguous.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we may silently read/write a register at offset 0. Change
this to WARN and then ignore the write or read-back all-ones.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least on the R8A7790, RFS8 reflects the RINT8 (multicast) MAC
status flag.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
My previous fix to clear padding of short frames used skb->len as the
DMA length, assuming that skb_padto() extended skb->len to include the
padding. That isn't the case; we need to use skb_put_padto() instead.
(This wasn't immediately obvious because software padding isn't
actually needed on the R-Car H2. We could make it conditional on
which chip is being driven, but it's probably not worth the effort.)
Reported-by: "Violeta Menéndez González" <violeta.menendez@codethink.co.uk>
Fixes: 612a17a54b50 ("sh_eth: Fix padding of short frames on TX")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit fd9af07c34.
The hardware manual states that the frame error and multicast bits are
copied to bits 9:0 of RD0, not bits 25:16. I've tested that this is
true for RFS1 (CRC error), RFS3 (frame too short), RFS4 (frame too
long) and RFS8 (multicast).
Also adjust a comment to agree with this.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of RX ring underrun (RDE), we attempt to reset the software
descriptor pointers (dirty_rx and cur_rx) to match where the hardware
will read the next descriptor from, as that might not be the first
dirty descriptor. This relies on reading RDFAR, but that register
doesn't exist on all supported chips - specifically, not on the R-Car
chips. This will result in unpredictable behaviour on those chips
after an RDE.
Make this pointer reset conditional and assume that it isn't needed on
the R-Car chips. This fix also assumes that RDFAR is never exposed at
offset 0 in the memory map - this is currently true, and a subsequent
commit will fix the ambiguity between offset 0 and no-offset in the
register offset maps.
Fixes: 79fba9f517 ("net: sh_eth: fix the rxdesc pointer when rx ...")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When submitting a DMA descriptor, the active bit must be written last.
When reading a completed DMA descriptor, the active bit must be read
first.
Add memory barriers to ensure that this ordering is maintained.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 740c7f31c0 ("sh_eth: Ensure DMA engines are stopped before
freeing buffers") added a call to sh_eth_reset() to the
sh_eth_set_ringparam() and sh_eth_close() paths.
However, setting the software reset bit(s) in the EDMR register resets
the MAC Address Registers to zero. Hence after kexec, the new kernel
doesn't detect a valid MAC address and assigns a random MAC address,
breaking DHCP.
Set the MAC address again after the reset in sh_eth_dev_exit() to fix
this.
Tested on r8a7740/armadillo (GETHER) and r8a7791/koelsch (FAST_RCAR).
Fixes: 740c7f31c0 ("sh_eth: Ensure DMA engines are stopped before freeing buffers")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/arm/boot/dts/imx6sx-sdb.dts
net/sched/cls_bpf.c
Two simple sets of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
- Use the return value of dma_map_single(), rather than calling
virt_to_page() separately
- Check for mapping failue
- Call dma_unmap_single() rather than dma_sync_single_for_cpu()
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
dma_map_single() may fail if an IOMMU or swiotlb is in use, so
we need to check for this.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we try to clear EDRRR and EDTRR and immediately continue to
free buffers. This is unsafe because:
- In general, register writes are not serialised with DMA, so we still
have to wait for DMA to complete somehow
- The R8A7790 (R-Car H2) manual states that the TX running flag cannot
be cleared by writing to EDTRR
- The same manual states that clearing the RX running flag only stops
RX DMA at the next packet boundary
I applied this patch to the driver to detect DMA writes to freed
buffers:
> --- a/drivers/net/ethernet/renesas/sh_eth.c
> +++ b/drivers/net/ethernet/renesas/sh_eth.c
> @@ -1098,7 +1098,14 @@ static void sh_eth_ring_free(struct net_device *ndev)
> /* Free Rx skb ringbuffer */
> if (mdp->rx_skbuff) {
> for (i = 0; i < mdp->num_rx_ring; i++)
> + memcpy(mdp->rx_skbuff[i]->data,
> + "Hello, world", 12);
> + msleep(100);
> + for (i = 0; i < mdp->num_rx_ring; i++) {
> + WARN_ON(memcmp(mdp->rx_skbuff[i]->data,
> + "Hello, world", 12));
> dev_kfree_skb(mdp->rx_skbuff[i]);
> + }
> }
> kfree(mdp->rx_skbuff);
> mdp->rx_skbuff = NULL;
then ran the loop:
while ethtool -G eth0 rx 128 ; ethtool -G eth0 rx 64; do echo -n .; done
and 'ping -f' toward the sh_eth port from another machine. The
warning fired several times a minute.
To fix these issues:
- Deactivate all TX descriptors rather than writing to EDTRR
- As there seems to be no way of telling when RX DMA is stopped,
perform a soft reset to ensure that both DMA enginess are stopped
- To reduce the possibility of the reset truncating a transmitted
frame, disable egress and wait a reasonable time to reach a
packet boundary before resetting
- Update statistics before resetting
(The 'reasonable time' does not allow for CS/CD in half-duplex
mode, but half-duplex no longer seems reasonable!)
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
If RX traffic is overflowing the FIFO or DMA ring, logging every time
this happens just makes things worse. These errors are visible in the
statistics anyway.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to stop the RX path accessing the RX ring while it's being
stopped or resized, we clear the interrupt mask (EESIPR) and then call
free_irq() or synchronise_irq(). This is insufficient because the
interrupt handler or NAPI poller may set EESIPR again after we clear
it. Also, in sh_eth_set_ringparam() we currently don't disable NAPI
polling at all.
I could easily trigger a crash by running the loop:
while ethtool -G eth0 rx 128 && ethtool -G eth0 rx 64; do echo -n .; done
and 'ping -f' toward the sh_eth port from another machine.
To fix this:
- Add a software flag (irq_enabled) to signal whether interrupts
should be enabled
- In the interrupt handler, if the flag is clear then clear EESIPR
and return
- In the NAPI poller, if the flag is clear then don't set EESIPR
- Set the flag before enabling interrupts in sh_eth_dev_init() and
sh_eth_set_ringparam()
- Clear the flag and serialise with the interrupt and NAPI
handlers before clearing EESIPR in sh_eth_close() and
sh_eth_set_ringparam()
After this, I could run the loop for 100,000 iterations successfully.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the device is down then no packet buffers should be allocated.
We also must not touch its registers as it may be powered off.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must only ever stop TX queues when they are full or the net device
is not 'ready' so far as the net core, and specifically the watchdog,
is concerned. Otherwise, the watchdog may fire *immediately* if no
packets have been added to the queue in the last 5 seconds.
What's more, sh_eth_tx_timeout() will likely crash if called while
we're resizing the TX ring.
I could easily trigger this by running the loop:
while ethtool -G eth0 rx 128 && ethtool -G eth0 rx 64; do echo -n .; done
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an skb to be transmitted is shorter than the minimum Ethernet frame
length, we currently set the DMA descriptor length to the minimum but
do not add zero-padding. This could result in leaking sensitive
data. We also pass different lengths to dma_map_single() and
dma_unmap_single().
Use skb_padto() to pad properly, before calling dma_map_single().
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add sh_eth_{suspend|resume}() implementing {suspend|resume|freeze|thaw|poweroff|
restore}() PM methods to make it possible to restore from hibernation not only
in Linux but also in e.g. U-Boot and to have more determined state on resume/
restore.
Signed-off-by: Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>
[Sergei: moved sh_eth_{suspend|resume}() before sh_eth_runtime_nop(), enclosed
them with #ifdef CONFIG_PM_SLEEP, reordered the local variables, got rid of
*goto* and label, reordered macro invocations, renamed, modified the changelog.]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use SET_RUNTIME_PM_OPS() macro to initialize the runtime PM method pointers in
the 'struct dev_pm_ops'.
Signed-off-by: Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>
[Sergei: renamed, added the changelog.]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver connects and disconnects the PHY device whenever the
net device is brought up and down. The ethtool get_settings,
set_settings and nway_reset operations will dereference a null
or dangling pointer if called while it is down.
I think it would be preferable to keep the PHY connected, but there
may be good reasons not to.
As an immediate fix for this bug:
- Set the phydev pointer to NULL after disconnecting the PHY
- Change those three operations to return -ENODEV while the PHY is
not connected
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently net_device_ops::set_rx_mode is only implemented for
chips with a TSU (multiple address table). However we do need
to turn the PRM (promiscuous) flag on and off for other chips.
- Remove the unlikely() from the TSU functions that we may safely
call for chips without a TSU
- Make setting of the MCT flag conditional on the tsu capability flag
- Rename sh_eth_set_multicast_list() to sh_eth_set_rx_mode() and plumb
it into both net_device_ops structures
- Remove the previously-unreachable branch in sh_eth_rx_mode() that
would otherwise reset the flags to defaults for non-TSU chips
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace "unsigned long" by "u32" when handling 32-bit register data.
A.o., this saves 11 * 36 bytes in the static sh_eth_cpu_data structures
when compiling for 64-bit.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit b284fbe3b3 ("sh_eth: Fix access to TRSCER register") wanted
to add a .trscer_err_mask value to the R-Car Gen2 family-specific data
structure (r8a779x_data), but it was accidentally added to the
SH7724-specific data structure (sh7724_data).
Presumably this happened due to a patch conflict with commit
d407bc0203 ("sh-eth: Set fdr_value of R-Car SoCs"), which added
another field at the same position.
Move the field setting to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: b284fbe3b3 ("sh_eth: Fix access to TRSCER register")
Signed-off-by: David S. Miller <davem@davemloft.net>
TRSCER register is configured differently by SoCs. TRSCER of R-Car Gen2 is
RINT8 bit only valid, other bits are reserved bits. This removes access to
TRSCER register reserve bit by adding variable trscer_err_mask to
sh_eth_cpu_data structure, set the register information to each SoCs.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FDR register of R-Car set in fdr_value can have the original settings.
This sets the value that is suitable for each SoCs to fdr_value of R8A777x
and R8A779x.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/amd/xgbe/xgbe-desc.c
drivers/net/ethernet/renesas/sh_eth.c
Overlapping changes in both conflict cases.
Signed-off-by: David S. Miller <davem@davemloft.net>
PTR_ALIGN macro after skb_reserve is redundant, because skb_reserve
function adjusts the alignment of skb->data.
Signed-off-by: Mitsuhiro Kimura <mitsuhiro.kimura.kc@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both of 'boguscnt' and 'quota' have nearly meaning as the condition of
the reception loop.
In order to cut down redundant processing, this patch changes excess
judgement.
Signed-off-by: Mitsuhiro Kimura <mitsuhiro.kimura.kc@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current driver, allocation size of skb does not care the alignment
adjust after allocation.
And also, in the current implementation, buffer alignment method by
sh_eth_set_receive_align function has a bug that this function displace
buffer start address forcedly when the alignment is corrected.
In the result, tail of the skb will exceed allocated area and kernel panic
will be occurred.
This patch fix this issue.
Signed-off-by: Mitsuhiro Kimura <mitsuhiro.kimura.kc@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device tree probing for R-Car M2N (r8a7793) is added.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using RMMI mode, it is necessary to change in probe.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
devm_ioremap_resource checks platform_get_resource() return value.
We can remove the duplicate check here.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
Renesas SuperH Ethernet support should be available only on
Renesas ARM SoCs and SuperH architecture.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Magnus Damm <magnus.damm@gmail.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since consume_skb() (and hence dev_kfree_skb() macro) checks the passed pointer
for NULL, there's no need to check for NULL before invoking dev_kfree_skb().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an issue that we cannot use nfs rootfs correctly
on r8a7790 when the command below runs on a host PC.
$ sudo ping -f -l 8 $BOARD_IP_ADDR
Since the driver sets the RACT to 1 in the first while loop of
sh_eth_rx(), the controller accepts a next frame into the next RX
descriptor during the while loop. But, in the first while loop
doesn't allocate a next skb. So, this patch removes the RACT setting
in the first while loop of sh_eth_rx().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the packet "exceeded" condition in sh_eth_rx() when
RACT in an RX descriptor is not set and the "quota" is 0.
Otherwise, kernel panic happens because the "&n->poll_list" is deleted
twice in sh_eth_poll() which calls napi_complete() and net_rx_action().
Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
include/net/inetpeer.h
net/ipv6/output_core.c
Changes in net were fixing bugs in code removed in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4a55530f38 (net: sh_eth: modify the definitions of register) managed
to leave out the E-DMAC register entries in sh_eth_offset_fast_sh3_sh2[], thus
totally breaking SH7619/771x support. Add the missing entries using the data
from before that commit.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current behaviour of the sh_eth driver is not to use the RNC bit
for the receive ring. This means that every packet recieved is not only
generating an IRQ but it also stops the receive ring DMA as well until
the driver re-enables it after unloading the packet.
This means that a number of the following errors are generated due to
the receive packet FIFO overflowing due to nowhere to put packets:
net eth0: Receive FIFO Overflow
Since feedback from Yoshihiro Shimoda shows that every supported LSI
for this driver should have the bit enabled it seems the best way is
to remove the RMCR default value from the per-system data and just
write it when initialising the RMCR value. This is discussed in
the message (http://www.spinics.net/lists/netdev/msg284912.html).
I have tested the RMCR_RNC configuration with NFS root filesystem and
the driver has not failed yet. There are further test reports from
Sergei Shtylov and others for both the R8A7790 and R8A7791.
There is also feedback fron Cao Minh Hiep[1] which reports the
same issue in (http://comments.gmane.org/gmane.linux.network/316285)
showing this fixes issues with losing UDP datagrams under iperf.
Tested-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I was converting the driver to the managed device API, only devm_kzalloc()
was available for memory allocation, so I had to use it, despite zeroing out the
PHY IRQ array right before initializing all its entries to PHY_POLL was quite
stupid. Now that devm_kmalloc_array() has become available, we can avoid the
needless zeroing out...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net: get rid of SET_ETHTOOL_OPS
Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.
Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
- SET_ETHTOOL_OPS(dev, ops);
+ dev->ethtool_ops = ops;
Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pm_rumtime work queue is causing the device to be suspended during
initialisation, thus the initialisation may not be able to access registers
properly. As the code is called from a work queue, it is possible that this
is not seen from certain configurations/builds due to the asynchronos
nature of the code.
Another issue has also been found where the network device registration
calls back into the driver thus causing further pm_runtime calls that
also caused issues with the MDIO bus code. This has now been checked
and is the only place the MDIO can be called without the device open.
Use pm_runtime_get_sync() and pm_runtime_put() to ensure that the
pm system does not suspend it during the probe() call and remove the
now unnecessary pm_runtime_resume() call. Also add a call in the error
path to call pm_runtime_disable().
This fixes the external abort that can cause /sbin/init or other such
init processed to die.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"goto" is well accepted for error paths in the kernel but should not be
used unnecessarily. Return the correct value directly instead of using a
goto when possible.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Network API functions that rely on the MDIO bus can be called as soon as
the driver calls register_netdev(). Register the MDIO bus before the
network device to avoid race conditions.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network device passed to the sh_mdio_init and sh_mdio_release
functions is only used to access the sh_eth_private instance. Pass it
directly to those functions.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO bus parent is set to the network device. Beside not reflecting
the hardware topology, this prevents registering the MDIO bus before
initializing the network device. Fix it by setting the MDIO bus parent
to the platform device.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Memory allocated for the MDIO bus with the devm_kzalloc() API is
associated with the network device. While this will cause memory to be
freed at the right time, it doesn't allow allocating memory before the
network device is initialized.
Replace the network device with the parent platform device for memory
allocation to remove that dependency. This also improves consistency
with the other devm_* calls in the driver that all use the platform
device.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we call netdev_*() under netif_msg_*() checks, we can fold these into
netif_*() macro invocations.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert dev_*(&ndev->dev, ...) to netdev_*(ndev, ...) calls since they are a bit
shorter and at the same time give more information on a device.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert pr_*() to netdev_*() calls as the latter provide info on a device.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Exit the driver's probe() method when the register layout is unknown as the
driver would cause kernel oops in this case anyway.
While at it, move the corresponding error message printout and convert it from
pr_err() to dev_err().
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the sh_eth device is registered using OF, then the driver
should call of_mdiobus_register() to register the PHYs described
in the devicetree and then use of_phy_connect() to connect the
PHYs to the device.
This ensures that any PHYs registered in the device tree are
appropriately connected to the parent devices nodes so that
the PHY drivers can access their OF properties.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support of the device tree probing for the Renesas SH-Mobile SoCs
documenting the device tree binding as necessary.
This work is loosely based on the original patch by Nobuhiro Iwamatsu
<nobuhiro.iwamatsu.yj@renesas.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver #define's and uses ETHERSMALL macro for the minimum Ethernet frame
size for which we have a standard macro ETH_ZLEN. Use the latter instead of
the home-grown one.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The r7s72100 SoC includes a fast ethernet controller.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return a boolean from sh_eth_is_gether() and refactor it as a one-liner.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
This covers everything under drivers/net except for wireless, which
has been submitted separately.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sh_eth_error() in case of a TX error tries to print a message using 2 dev_err()
calls with the first string not finished by '\n', so that the resulting message
would inevitably come out garbled, with something like "3net eth0: " inserted
in the middle. Avoid that by merging 2 calls into one.
While at it, insert an empty line after the nearby declaration.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Running 'scripts/checkpatch.pl' on the driver files gives numerous warnings:
- block comments using empty /* line;
- unneeded \ at end of lines;
- message string split across lines;
- use of __attribute__((aligned(n))) instead of __aligned(n) macro;
- use of __attribute__((packed)) instead of __packed macro.
Additionally, running 'scripts/checkpatch.pl --strict' gives more complaints:
- including the paragraph about writing to FSF into the heading comment;
- alignment not matching open paren;
- multiple assignments on one line;
- use of CamelCase names;
- missing {} on one of the *if* arms where another has them;
- spinlock definition without a comment.
While fixing these, also do some more style cleanups:
- remove useless () around expressions;
- add {} around multi-line *if* operator's arm;
- remove space before comma;
- add spaces after /* and before */;
- properly align continuation lines of broken up expressions;
- realign comments to the structure fields.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use possibly more efficient ether_addr_equal
to instead of memcmp.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no need anymore to call phy_init_hw() to reset/resume the PHY from the
driver, as the call chain in phylib already has reached it, and so reset/resumed
the PHY (even resuming it twice). This duplicate reset is not only needless, it
e.g. clears the PHY's interrupt enables just setup by phylib and so prevents the
expected IRQs from the PHY.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the platform code to pass PHY's IRQ to the driver. Print this IRQ along
with the other PHY datails in sh_eth_phy_init().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for yet another ARM member of the R-Car family, R-Car M2, also known
as R8A7791 -- it will share the code and data with previously added R8A7790.
Despite the Ether devices in these SoCs are indistinguishable at least from the
driver's point of view, we do introduce a new platform device ID "r8a7791-ether"
unlike the wildcard ID used for R8A7778/9 SoCs, due to newly established policy
for the Renesas SoCs.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sh_eth driver issues an uncontrolled PHY reset through the MII
register BMCR but fails to wait for the reset to complete, and will also
implicitely wipe out all possible PHY fixups applied. Use phy_init_hw()
which remedies both problems.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the platform data pointer before dereferencing it and error out of the
probe() method if it's NULL.
This has additional effect of preventing kernel oops with outdated platform data
containing zero PHY address instead (such as on SolutionEngine7710).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Declare 'enum RMCR_BIT' containing the single member for the RMCR.RNC bit and
replace bare numbers in the driver by this mnemonic.
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/qmi_wwan.c
include/net/dst.h
Trivial merge conflicts, both were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Nguyen Hong Ky posted a patch to correct RX packet errors on R8A7740 which
was applied as 2c6221e4a5 ("net: sh_eth: Fix RX packets errors on
R8A7740"). Unfortunately sh_eth.c contains many similar instances
of struct sh_eth_cpu_data and the patch was miss-applied, updating
sh7734_data instead of r8a7740_data.
This patch corrects this problem by.
1. Reverting the change to sh7734_data and;
2. Applying the change to r8a7740_data.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
include/linux/netdevice.h
net/core/sock.c
Trivial merge issues.
Removal of "extern" for functions declaration in netdevice.h
at the same time "const" was added to an argument.
Two parallel line additions in net/core/sock.c
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch will fix RX packets errors when receiving big size
of data by set bit RNC = 1.
RNC - Receive Enable Control
0: Upon completion of reception of one frame, the E-DMAC writes
the receive status to the descriptor and clears the RR bit in
EDRRR to 0.
1: Upon completion of reception of one frame, the E-DMAC writes
(writes back) the receive status to the descriptor. In addition,
the E-DMAC reads the next descriptor and prepares for reception
of the next frame.
In addition, for get more stable when receiving packets, I set
maximum size for the transmit/receive FIFO and inserts padding
in receive data.
Signed-off-by: Nguyen Hong Ky <nh-ky@jinso.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the memset/memcpy uses of 6 to ETH_ALEN
where appropriate.
Also convert some struct definitions and u8 array
declarations of [6] to ETH_ALEN.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
net/bridge/br_multicast.c
net/ipv6/sit.c
The conflicts were minor:
1) sit.c changes overlap with change to ip_tunnel_xmit() signature.
2) br_multicast.c had an overlap between computing max_delay using
msecs_to_jiffies and turning MLDV2_MRC() into an inline function
with a name using lowercase instead of uppercase letters.
3) stmmac had two overlapping changes, one which conditionally allocated
and hooked up a dma_cfg based upon the presence of the pbl OF property,
and another one handling store-and-forward DMA made. The latter of
which should not go into the new of_find_property() basic block.
Signed-off-by: David S. Miller <davem@davemloft.net>
While implementing NAPI for the driver, I overlooked the race conditions where
interrupt handler might have called napi_schedule_prep() before napi_enable()
was called or after napi_disable() was called. If RX interrupt happens, this
would cause the endless interrupts and messages like:
sh-eth eth0: ignoring interrupt, status 0x00040000, mask 0x01ff009f.
The interrupt wouldn't even be masked by the kernel eventually since the handler
would return IRQ_HANDLED all the time.
As a fix, move napi_enable() call before request_irq() call and napi_disable()
call after free_irq() call.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver supporting NAPI should use NAPI-specific function for receiving packets,
so netif_rx() should be changed to netif_receive_skb().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This corrects an oversight when r8a7790 support was added to sh_eth.
Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no need to call ether_setup() in the driver since prior alloc_etherdev()
call already arranges for it.
Suggested-by: Denis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the 'register_type' field of the 'sh_eth' driver's platform data is not
used by the driver anymore, it's time to remove it and its initializers from
the SH platform code. Also move *enum* declaring values for this field from
<linux/sh_eth.h> to the local driver's header file as they're only needed
by the driver itself now...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register layout is a SoC characteristic, so it's wrong that it's stored
in the otherwise board specific platform data. Add 'register_type' field to
'struct sh_eth_cpu_data', initialize it properly for each SoC, and read it
from this structure instead of the platfrom data from now on...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RFE interrupt is enabled for the r8a7790 but isn't handled,
resulting in the interrupts core noticing unhandled interrupts, and
eventually disabling the ethernet IRQ.
Fix it by adding RFE to the bitmask of error interrupts to be handled
for r8a7790.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a copy of support for r8a7778/9 with the .rmiimode mode bit
of struct sh_eth_cpu_data set.
Also update R8A7779 to R8A777x.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register is prsent on the r8a7790 SoC.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
If NO_DMA=y:
drivers/built-in.o: In function `sh_eth_free_dma_buffer':
drivers/net/ethernet/renesas/sh_eth.c:1103: undefined reference to `dma_free_coherent'
drivers/net/ethernet/renesas/sh_eth.c:1110: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `sh_eth_ring_init':
drivers/net/ethernet/renesas/sh_eth.c:1065: undefined reference to `dma_alloc_coherent'
drivers/net/ethernet/renesas/sh_eth.c:1086: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `sh_eth_ring_format':
drivers/net/ethernet/renesas/sh_eth.c:988: undefined reference to `dma_map_single'
drivers/built-in.o: In function `sh_eth_txfree':
drivers/net/ethernet/renesas/sh_eth.c:1220: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `sh_eth_rx':
drivers/net/ethernet/renesas/sh_eth.c:1323: undefined reference to `dma_map_single'
drivers/built-in.o: In function `sh_eth_start_xmit':
drivers/net/ethernet/renesas/sh_eth.c:1954: undefined reference to `dma_map_single'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/freescale/fec_main.c
drivers/net/ethernet/renesas/sh_eth.c
net/ipv4/gre.c
The GRE conflict is between a bug fix (kfree_skb --> kfree_skb_list)
and the splitting of the gre.c code into seperate files.
The FEC conflict was two sets of changes adding ethtool support code
in an "!CONFIG_M5272" CPP protected block.
Finally the sh_eth.c conflict was between one commit add bits set
in the .eesr_err_check mask whilst another commit removed the
.tx_error_check member and assignments.
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to obviously missing braces, EESR.TABT (transmit abort) interrupt may be
reported even if it hasn't happened, just when EESR.TWB (transmit descriptor
write-back) interrupt happens. Luckily (?), EESR.TWB is disabled by the driver
via the TRIMD register and all the interrupt masks, so that transmit abort is
never actually logged...
Put the braces where they should be and fix the incoherent comment, while at it.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EESR.RFE (receive FIFO overflow) interrupt is enabled by the driver on all SoCs
and sh_eth_error() handles it but it's not present in any initializer/assignment
of the 'eesr_err_check' field of 'struct sh_eth_cpu_data'. This leads to that
interrupt not being handled and cleared, and finally to disabling IRQ and the
driver being non-functional.
Modify DEFAULT_EESR_ERR_CHECK macro and all explicit initializers of the above
mentioned field to contain the EESR.RFE bit. Remove useless backslashes from the
initializers, while at it.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All drivers that select MII also need to select NET_CORE because MII
depends on it. This is a bit ridiculous because NET_CORE is just a
menu option that doesn't enable any code by itself.
There is also no need for it to be a visible option, since its users
all select it.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only R8A7740 specific #ifdef hindering ARM multiplatform build is left in
sh_eth_rx(): it covers the code shifting Rx buffer descriptor word 0 by 16. Get
rid of the #ifdef by adding 'shift_rd0' field to the 'struct sh_eth_cpu_data',
making the shift dependent on it, and setting it to 1 for the R8A7740 case...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the comment to 'enum TD_STS_BIT', reformat the values, and add a couple of
values missing before (though unused by the driver).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For SH7724 'eesipr_value' field initializer includes DMAC_M_RFRMER & DMAC_M_ECI
bits which are already contained in 0x01ff009f -- remove them.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
