This adds a simple sysfs interface for GPIOs.
/sys/class/gpio
/export ... asks the kernel to export a GPIO to userspace
/unexport ... to return a GPIO to the kernel
/gpioN ... for each exported GPIO #N
/value ... always readable, writes fail for input GPIOs
/direction ... r/w as: in, out (default low); write high, low
/gpiochipN ... for each gpiochip; #N is its first GPIO
/base ... (r/o) same as N
/label ... (r/o) descriptive, not necessarily unique
/ngpio ... (r/o) number of GPIOs; numbered N .. N+(ngpio - 1)
GPIOs claimed by kernel code may be exported by its owner using a new
gpio_export() call, which should be most useful for driver debugging.
Such exports may optionally be done without a "direction" attribute.
Userspace may ask to take over a GPIO by writing to a sysfs control file,
helping to cope with incomplete board support or other "one-off"
requirements that don't merit full kernel support:
echo 23 > /sys/class/gpio/export
... will gpio_request(23, "sysfs") and gpio_export(23);
use /sys/class/gpio/gpio-23/direction to (re)configure it,
when that GPIO can be used as both input and output.
echo 23 > /sys/class/gpio/unexport
... will gpio_free(23), when it was exported as above
The extra D-space footprint is a few hundred bytes, except for the sysfs
resources associated with each exported GPIO. The additional I-space
footprint is about two thirds of the current size of gpiolib (!). Since
no /dev node creation is involved, no "udev" support is needed.
Related changes:
* This adds a device pointer to "struct gpio_chip". When GPIO
providers initialize that, sysfs gpio class devices become children of
that device instead of being "virtual" devices.
* The (few) gpio_chip providers which have such a device node have
been updated.
* Some gpio_chip drivers also needed to update their module "owner"
field ... for which missing kerneldoc was added.
* Some gpio_chips don't support input GPIOs. Those GPIOs are now
flagged appropriately when the chip is registered.
Based on previous patches, and discussion both on and off LKML.
A Documentation/ABI/testing/sysfs-gpio update is ready to submit once this
merges to mainline.
[akpm@linux-foundation.org: a few maintenance build fixes]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Cc: Greg KH <greg@kroah.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following patch allows the avr32_comparator interrupt to be shared.
This is necessary as the avr32 oprofile driver shares the irq group 0
with the timer.
To make OProfile actually work on AVR32, a small patch for oprofiled is
also needed (posted to the oprofile mailing list).
Signed-off-by: Nikolaus Voss <n.voss@weinmann.de>
[haavard.skinnemoen@atmel.com: set IRQF_SHARED unconditionally]
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
nohz: adjust tick_nohz_stop_sched_tick() call of s390 as well
nohz: prevent tick stop outside of the idle loop
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
arch/mips/kernel/stacktrace.c: Heiko can't type
kthread: reduce stack pressure in create_kthread and kthreadd
fix core/stacktrace changes on avr32, mips, sh
On 32-bit architectures PAGE_ALIGN() truncates 64-bit values to the 32-bit
boundary. For example:
u64 val = PAGE_ALIGN(size);
always returns a value < 4GB even if size is greater than 4GB.
The problem resides in PAGE_MASK definition (from include/asm-x86/page.h for
example):
#define PAGE_SHIFT 12
#define PAGE_SIZE (_AC(1,UL) << PAGE_SHIFT)
#define PAGE_MASK (~(PAGE_SIZE-1))
...
#define PAGE_ALIGN(addr) (((addr)+PAGE_SIZE-1)&PAGE_MASK)
The "~" is performed on a 32-bit value, so everything in "and" with
PAGE_MASK greater than 4GB will be truncated to the 32-bit boundary.
Using the ALIGN() macro seems to be the right way, because it uses
typeof(addr) for the mask.
Also move the PAGE_ALIGN() definitions out of include/asm-*/page.h in
include/linux/mm.h.
See also lkml discussion: http://lkml.org/lkml/2008/6/11/237
[akpm@linux-foundation.org: fix drivers/media/video/uvc/uvc_queue.c]
[akpm@linux-foundation.org: fix v850]
[akpm@linux-foundation.org: fix powerpc]
[akpm@linux-foundation.org: fix arm]
[akpm@linux-foundation.org: fix mips]
[akpm@linux-foundation.org: fix drivers/media/video/pvrusb2/pvrusb2-dvb.c]
[akpm@linux-foundation.org: fix drivers/mtd/maps/uclinux.c]
[akpm@linux-foundation.org: fix powerpc]
Signed-off-by: Andrea Righi <righi.andrea@gmail.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Almost all users of this field need a PFN instead of a physical address,
so replace node_boot_start with node_min_pfn.
[Lee.Schermerhorn@hp.com: fix spurious BUG_ON() in mark_bootmem()]
Signed-off-by: Johannes Weiner <hannes@saeureba.de>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
free_area_init_node() gets passed in the node id as well as the node
descriptor. This is redundant as the function can trivially get the node
descriptor itself by means of NODE_DATA() and the node's id.
I checked all the users and NODE_DATA() seems to be usable everywhere
from where this function is called.
Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Flag platforms as HAVE_CLK (or not) in Kconfig, based on whether they
support <linux/clk.h> calls, so that otherwise portable drivers which need
those calls can list that dependency.
Something like this is a prerequisite for merging the musb_hdrc driver,
currently used on platforms including Davinci, OMAP2430, OMAP3xx ... and
the discrete TUSB6010 chip, which doesn't have a natural platform
dependency. (Used with OMAP 2420 in current Nokia N8x0 tablets.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds platform data to the AC97C platform device. This will
let the board add a GPIO line which is connected to the external codecs
reset line.
The platform data, ac97c_platform_data, must also contain the DMA
controller ID, RX channel ID and TX channel ID.
Tested with Wolfson WM9712 and AP7000.
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (24 commits)
I/OAT: I/OAT version 3.0 support
I/OAT: tcp_dma_copybreak default value dependent on I/OAT version
I/OAT: Add watchdog/reset functionality to ioatdma
iop_adma: cleanup iop_chan_xor_slot_count
iop_adma: document how to calculate the minimum descriptor pool size
iop_adma: directly reclaim descriptors on allocation failure
async_tx: make async_tx_test_ack a boolean routine
async_tx: remove depend_tx from async_tx_sync_epilog
async_tx: export async_tx_quiesce
async_tx: fix handling of the "out of descriptor" condition in async_xor
async_tx: ensure the xor destination buffer remains dma-mapped
async_tx: list_for_each_entry_rcu() cleanup
dmaengine: Driver for the Synopsys DesignWare DMA controller
dmaengine: Add slave DMA interface
dmaengine: add DMA_COMPL_SKIP_{SRC,DEST}_UNMAP flags to control dma unmap
dmaengine: Add dma_client parameter to device_alloc_chan_resources
dmatest: Simple DMA memcpy test client
dmaengine: DMA engine driver for Marvell XOR engine
iop-adma: fix platform driver hotplug/coldplug
dmaengine: track the number of clients using a channel
...
Fixed up conflict in drivers/dca/dca-sysfs.c manually
This allow to dynamically generate attributes and share show/store
functions between attributes. Right now most attributes are generated
by special macros and lots of duplicated code. With the attribute
passed it's instead possible to attach some data to the attribute
and then use that in shared low level functions to do different things.
I need this for the dynamically generated bank attributes in the x86
machine check code, but it'll allow some further cleanups.
I converted all users in tree to the new show/store prototype. It's a single
huge patch to avoid unbisectable sections.
Runtime tested: x86-32, x86-64
Compiled only: ia64, powerpc
Not compile tested/only grep converted: sh, arm, avr32
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jack Ren and Eric Miao tracked down the following long standing
problem in the NOHZ code:
scheduler switch to idle task
enable interrupts
Window starts here
----> interrupt happens (does not set NEED_RESCHED)
irq_exit() stops the tick
----> interrupt happens (does set NEED_RESCHED)
return from schedule()
cpu_idle(): preempt_disable();
Window ends here
The interrupts can happen at any point inside the race window. The
first interrupt stops the tick, the second one causes the scheduler to
rerun and switch away from idle again and we end up with the tick
disabled.
The fact that it needs two interrupts where the first one does not set
NEED_RESCHED and the second one does made the bug obscure and extremly
hard to reproduce and analyse. Kudos to Jack and Eric.
Solution: Limit the NOHZ functionality to the idle loop to make sure
that we can not run into such a situation ever again.
cpu_idle()
{
preempt_disable();
while(1) {
tick_nohz_stop_sched_tick(1); <- tell NOHZ code that we
are in the idle loop
while (!need_resched())
halt();
tick_nohz_restart_sched_tick(); <- disables NOHZ mode
preempt_enable_no_resched();
schedule();
preempt_disable();
}
}
In hindsight we should have done this forever, but ...
/me grabs a large brown paperbag.
Debugged-by: Jack Ren <jack.ren@marvell.com>,
Debugged-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fixes this type of problem:
CC arch/s390/kernel/stacktrace.o
arch/s390/kernel/stacktrace.c:84: warning: data definition has no type or storage class
arch/s390/kernel/stacktrace.c:84: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/s390/kernel/stacktrace.c:84: warning: parameter names (without types) in function declaration
arch/s390/kernel/stacktrace.c:97: warning: data definition has no type or storage class
arch/s390/kernel/stacktrace.c:97: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/s390/kernel/stacktrace.c:97: warning: parameter names (without types) in function declaration
caused by "stacktrace: export save_stack_trace[_tsk]"
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch does a few small cleanups around the atmel mci platform code
and in the atmel-mci driver. The platform changes simply removes an
unused variable, uses the fact that by the end we always have some form
of platform data and notes that GPIO_PIN_NONE != 0. This last point
could cause the incorrect attempt to twice reserve pin PA0.
While we've got the hood up, add linux/err.h to the atmel-mci.c include
list. It needs it and generally pulls it by voodoo but I did once
stumble across a config which don't build.
This is against Linus' latest git.
Signed-off-by: Ben Nizette <bn@niasdigital.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This is a driver for the MMC controller on the AP7000 chips from
Atmel. It should in theory work on AT91 systems too with some
tweaking, but since the DMA interface is quite different, it's not
entirely clear if it's worth merging this with the at91_mci driver.
This driver has been around for a while in BSPs and kernel sources
provided by Atmel, but this particular version uses the generic DMA
Engine framework (with the slave extensions) instead of an
avr32-only DMA controller framework.
This driver can also use PIO transfers when no DMA channels are
available, and for transfers where using DMA may be difficult or
impractical for some reason (e.g. the DMA setup overhead is usually
not worth it for very short transfers, and badly aligned buffers or
lengths are difficult to handle.)
Currently, the driver only support PIO transfers. DMA support has been
split out to a separate patch to hopefully make it easier to review.
The driver has been tested using mmc-block and ext3fs on several SD,
SDHC and MMC+ cards. Reads and writes work fine, with read transfer
rates up to 3.5 MiB/s on fast cards with debugging disabled.
The driver has also been tested using the mmc_test module on the same
cards. All tests except 7, 9, 15 and 17 succeed. The first two are
unsupported by all the cards I have, so I don't know if the driver
handles this correctly. The last two fail because the hardware flags a
Data CRC Error instead of a Data Timeout error. I'm not sure how to deal
with that.
Documentation for this controller can be found in many data sheets from
Atmel, including the AT32AP7000 data sheet which can be found here:
http://www.atmel.com/dyn/products/datasheets.asp?family_id=682
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This adds a driver for the Synopsys DesignWare DMA controller (aka
DMACA on AVR32 systems.) This DMA controller can be found integrated
on the AT32AP7000 chip and is primarily meant for peripheral DMA
transfer, but can also be used for memory-to-memory transfers.
This patch is based on a driver from David Brownell which was based on
an older version of the DMA Engine framework. It also implements the
proposed extensions to the DMA Engine API for slave DMA operations.
The dmatest client shows no problems, but there may still be room for
improvement performance-wise. DMA slave transfer performance is
definitely "good enough"; reading 100 MiB from an SD card running at ~20
MHz yields ~7.2 MiB/s average transfer rate.
Full documentation for this controller can be found in the Synopsys
DW AHB DMAC Databook:
http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf
The controller has lots of implementation options, so it's usually a
good idea to check the data sheet of the chip it's intergrated on as
well. The AT32AP7000 data sheet can be found here:
http://www.atmel.com/dyn/products/datasheets.asp?family_id=682
Changes since v4:
* Use client_count instead of dma_chan_is_in_use()
* Add missing include
* Unmap buffers unless client told us not to
Changes since v3:
* Update to latest DMA engine and DMA slave APIs
* Embed the hw descriptor into the sw descriptor
* Clean up and update MODULE_DESCRIPTION, copyright date, etc.
Changes since v2:
* Dequeue all pending transfers in terminate_all()
* Rename dw_dmac.h -> dw_dmac_regs.h
* Define and use controller-specific dma_slave data
* Fix up a few outdated comments
* Define hardware registers as structs (doesn't generate better
code, unfortunately, but it looks nicer.)
* Get number of channels from platform_data instead of hardcoding it
based on CONFIG_WHATEVER_CPU.
* Give slave clients exclusive access to the channel
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>,
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Andrew Morton reported this against linux-next:
ERROR: ".save_stack_trace" [tests/backtracetest.ko] undefined!
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Implement Standby support. In this mode, we'll suspend all drivers,
put the SDRAM in self-refresh mode and switch off the HSB bus
("frozen" mode.)
Implement Suspend-to-mem support. In this mode, we suspend all
drivers, put the SDRAM into self-refresh mode and switch off all
internal clocks except the 32 kHz oscillator ("stop" mode.)
The lowest-level suspend code runs from a small portion of SRAM
allocated at startup time. This gets rid of a small potential race
with the SDRAM where we might try to enter self-refresh mode in the
middle of an icache burst. We also relocate all interrupt and
exception handlers to SRAM during the small window when we enter and
exit the low-power modes.
We don't need to do any special tricks to start and stop the PLL. The
main clock is automatically gated by hardware until the PLL is stable.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This makes the intc show up in sysfs (probably not very useful), and
allows us to easily add suspend/resume support later.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The SDRAM controller needs a clock in order to respond to our
commands, and suspend doesn't work very well without the SDRAM in
self-refresh mode.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Use a quicklist to allocate process PGDs. This is expected to be
slightly faster since we need to copy entries from swapper_pg_dir,
which can stay around for pages on the PGD quick list.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Expand the per-process PGDs so that they cover the kernel virtual
memory area as well. This simplifies the TLB miss handler fastpath
since it doesn't have to check for kernel addresses anymore.
If a TLB miss happens on a kernel address and a second-level page
table can't be found, we check swapper_pg_dir and copy the PGD entry
into the user PGD if it can be found there.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Instead of storing physical addresses along with page flags in the
PGD, store virtual addresses and use NULL to indicate a not present
second-level page table. A non-page-aligned page table indicates a bad
PMD.
This simplifies the TLB miss handler since it no longer has to check
the Present bit and no longer has to convert the PGD entry from
physical to virtual address. Instead, it has to check for a NULL
entry, which is slightly cheaper than either.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This and the following patches aim to optimize the code dealing with
page tables and TLB operations. Each patch reduces the time it takes
to gzip a 16 MB file slightly, but I expect things like fork() and
mmap() will improve somewhat more.
This patch deals with the low-level TLB operations:
* Remove unused _TLBEHI_I define
* Use gcc builtins instead of inline assembly
* Remove a few unnecessary pipeline flushes and nops
* Introduce NR_TLB_ENTRIES define and use it instead of hardcoding it
to 32 a few places throughout the code.
* Use sysreg bitops instead of hardcoded shifts and masks
* Make a few needlessly global functions static
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The only thing left in at32ap.c is some PDC stuff. Rename the file to
reflect what it actually does.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Combine at32_clock_init() and at32_portmux_init() into
setup_platform() and remove setup_platform() from at32ap.c. No
functional change since all setup_platform() ever did was call those
two functions.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Kill the special exception handler sections .tlbx.ex.text,
.tlbr.ex.text, tlbw.ex.text and .scall.text. Use .org instead to place
the handlers at the required offsets from EVBA.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The name "mck" causes a conflict on AT91. Call it "pwm_clk" instead.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This is a minor tweak to the at32ap700x pin configuration for the SPI
input pin (MISO), enabling the on-chip weak pullup (typical 190K) to
(a) ensure a fixed data value for missing or input-only slaves;
(b) prevent power waste associated with inputs floating near VDDIO/2.
Atmel's boards have no external pullup or pulldown on these pins, so
it's unlikely other boards would address these issues with external
pulldowns. Were there trouble, board-specific code could turn off
the relevant pullup(s).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Basic I2C initialization for the NGW100 board:
- Provide empty i2c device table. Daughtercards may add devices,
and the ATtiny24 could do stuff too.
- Set up EXTINT(3) so the ATtiny24 can interrupt the AP7000.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch adds the PS/2 interface (PSIF) to the device code, split into
two platform devices, one for each port.
The function for adding the PSIF platform device is also added to the
board header file.
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch lets the board code choose which pin out to use for the LCD
interface.
On AT32AP7000 the LCDC is wired to two sets of pins, which lets the user
choose between dual ethernet and 32-bit EBI. For the ATNGW100 board it
is vital to have the choice to select the alternative pinout since this
pinout is routed to the external headers.
Update ATSTK1002 and ATSTK1004 to use the new interface.
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
On the odd chance some code uses a pin as a GPIO IRQ without calling
gpio_request() or gpio_direction_input(), the debug dump should still
show its pin status.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
__raw_readsb() should always use byte accesses, never halfword accesses,
to I/O memory.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
A signal handler should be able to change the signal stack used for the
next signal by altering the ucontext_t passed as a parameter to the
handler. This does not currently work on avr32 since it doesn't update
the in-kernel signal context from the ucontext_t upon signal handler
return.
Fix it by adding a call to do_sigaltstack() from sys_rt_sigreturn(),
bringing it in line with most other architectures.
Signed-off-by: Martin Koegler <mkoegler@auto.tuwien.ac.at>
[haavard.skinnemoen@atmel.com: changed patch description]
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
On our custom board we have other oscillator rates than on atngw100 and
atstk100x.
Currently these rates are hardcoded in arch/avr32/mach-at32ap/at32ap700x.c.
This patch moves them into board specific code.
Signed-off-by: Alex Raimondi <raimondi@miromico.ch>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Fixes one of two ext4 build problems:
ERROR: "empty_zero_page" [fs/ext4/ext4dev.ko] undefined!
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The ATSTK1006 is basically an upgraded version of ATSTK1002 with
128 MiB SDRAM and 256 MiB NAND flash on board.
Otherwise, the board is very similar to the ATSTK1002, so it uses the
same board support file.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This function initializes and adds a platform_device for a NAND flash
interface on SMC chip select 3.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The board init code, typically running from postcore_initcall, may
need to set up SMC timings. We have to make sure the SMC driver is
ready before this happens.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Move the AP7 cpufreq init to late_initcall() so that we don't try to
bring up cpufreq until the governor is ready. x86 also uses
late_initcall() for this.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Just provide reasonable defaults for the new stuff. Tickless and
hrtimers are turned on for all boards except ATSTK1004.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This replaces the duplicated arch-specific versions of "sys_pipe()" with
one unified implementation. This removes almost 250 lines of duplicated
code.
It's marked __weak, so that *if* an architecture wants to override the
default implementation it can do so by simply having its own replacement
version, since many architectures use alternate calling conventions for
the 'pipe()' system call for legacy reasons (ie traditional UNIX
implementations often return the two file descriptors in registers)
I still haven't changed the cris version even though Linus says the BKL
isn't needed. The arch maintainer can easily do it if there are really
no obstacles.
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use proc_create() to make sure that ->proc_fops be setup before gluing PDE to
main tree.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the user specified a fixed framebuffer address on the command line, it may
have been initialized already with a splash image or something, so we
shouldn't clear it.
Therefore, we should only initialize the framebuffer if we allocated it
ourselves. This patch also updates the AVR32 setup code to clear the
framebuffer if it allocated it itself, i.e. the user didn't provide a fixed
address or the reservation failed.
I've updated the at91 platform code as well so that it initializes the
framebuffer if it is located in SRAM, but I haven't tested that it actually
works.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Nicolas FERRE <nicolas.ferre@rfo.atmel.com>
Cc: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds in the indirect call to pm_power_off(), as is done in
other architectures (e.g. ARM).
Tested on NGW100, with custom board with GPIO control over main DC
power.
Signed-off-by: Peter Ma <pma@mediamatech.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch is a take two of adding full functionality to PLL1 on
AT32AP7000. This allows board-specific code and drivers to configure
and enable PLL1. This is useful when precise control over the
frequency of e.g. a genclock is needed and requested by users for the
ABDAC device.
The patch is based upon previous patches from both Haavard Skinnemoen
and David Brownell.
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This combines three patches from David Brownell:
* avr32: tclib support
* avr32: simplify clocksources
* avr32: Turn count/compare into a oneshot clockevent device
Register both TC blocks (instead of just the first one) so that
the AT32/AT91 tclib code will pick them up (instead of just the
avr32-only PIT-style clocksource).
Rename the first one and its resources appropriately.
More cleanups to the cycle counter clocksource code
- Disable all the weak symbol magic; remove the AVR32-only TCB-based
clocksource code (source and header).
- Mark the __init code properly.
- Don't forget to report IRQF_TIMER.
- Make the system work properly with this clocksource, by preventing
use of the CPU "idle" sleep state in the idle loop when it's used.
Package the avr32 count/compare timekeeping support as a oneshot
clockevent device, so it supports NO_HZ and high res timers.
This means it also supports plugging in other clockevent devices
and clocksources.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Create a new file, pm-at32ap700x.S, in mach-at32ap and move the CPU
idle sleep code there. Make it possible to disable the sleep code.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Move the only thing that was actually implemented and used in
asm/intc.h, intc_get_pending(), into asm/irq.h and delete asm/intc.h
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Start cleaning up the AVR32 clocksource mess, starting with the cycle
counter clocksource: remove unneeded pseudo-RTC (just inline that
call to mktime) and associated build warning, and unused sysdev.
Add comment about the problem using the cycle counter register,
and adjust the clocksource rating accordingly. Later patches can
make this usable again (by disabling use of the idle state and
providing a proper clocksource without the weak binding hacks)
and move towards TCB-based clockevent support (including high
resolution timers) that's shared between AT91 and AVR32.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
New-style I2C drivers require that motherboard-mounted I2C devices are
registered with the I2C core, typically at arch_initcall time. This
can be done nice and neat by passing the struct i2c_board_info[]
through at32_add_device_twi just like we do for the SPI board info.
While we've got the hood up, remove a duplicate declaration of
at32_add_device_twi() in board.h.
[hskinnemoen@atmel.com: add missing i2c_board_info forward-declaration]
Signed-Off-By: Ben Nizette <bn@niasdigital.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Semaphores are no longer performance-critical, so a generic C
implementation is better for maintainability, debuggability and
extensibility. Thanks to Peter Zijlstra for fixing the lockdep
warning. Thanks to Harvey Harrison for pointing out that the
unlikely() was unnecessary.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
There's a libata based PATA driver for avr32, but no support for
drivers/ide/ on avr32.
This patch fixes the following compile error:
<-- snip -->
...
CC [M] drivers/ide/ide-cd.o
In file included from /home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/ide-cd.c:37:
/home/bunk/linux/kernel-2.6/git/linux-2.6/include/linux/ide.h:209:21: error: asm/ide.h: No such file or directory
make[3]: *** [drivers/ide/ide-cd.o] Error 1
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The atmel_usba_udc driver is being used by several platforms and arches
(avr32 and at91 ATM), and each platform may have different endpoint
settings.
The patch below moves the endpoint declarations into the platform
data and make the necessary adjustments for AVR32 (improved by
Haavard Skinnemoen <hskinnemoen@atmel.com>).
Signed-off-by: Stelian Pop <stelian@popies.net>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
add_reserved_region() tries to keep the resource list sorted, so when
looking for a place to insert the new resource, it may break out
before the last entry.
When this happens, the list is broken in two because the sibling field
of the new entry doesn't point to the next resource. Fix it by
updating the new resource's sibling field appropriately.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Don't include the BUG trap handling code when CONFIG_BUG is not set.
This fixes allnoconfig.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Iff the parent has TIF_DEBUG set, _and_ clone_flags includes
CLONE_PTRACE we should set the TIF_DEBUG flag for the child and
increment the ocd refcount. Otherwise, the TIF_DEBUG flag must be
unset.
Currently, the child inherits TIF_DEBUG from the parent before
copy_thread is called, so TIF_DEBUG may be already be set before we
determine whether the child is supposed to inherit debugging
capabilities from the parent or not. This means that ocd_enable()
won't increment the refcount, because TIF_DEBUG is already set, and
that TIF_DEBUG will be set for processes that aren't being debugged.
This leads to a refcounting asymmetry, which may show up as
------------[ cut here ]------------
Badness at arch/avr32/kernel/ocd.c:73
PC is at ocd_disable+0x34/0x60
LR is at put_lock_stats+0xa/0x20
as reported by David Brownell. Happens when strace'ing a process that
forks a new child process, e.g. "strace mount -tjffs2 mtd1 /mnt", and
subsequently killing the child process (e.g. "umount /mnt".)
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This fixes a hang on boot with nohz enabled. nohz is not actually
supported in mainline yet, but patches that add support for it are
currently under review.
When nohz is compiled out, the functions are no-ops, so this patch
results in no functional change, but it arguably makes the code more
correct.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
CONFIG_BOARD_ATSTK1002_SW2_CUSTOM should be
CONFIG_BOARD_ATSTK100X_SW2_CUSTOM.
Spotted by Robert P. J. Day.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The per-task page tables only cover the first 2GiB of the address
space. For kernel addresses, we need to do the lookup in init's page
tables.
This is a temporary workaround until we modify the per-task page
tables to cover the whole 4GiB address space.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
To allow flexible configuration of IDE introduce HAVE_IDE.
All archs except arm, um and s390 unconditionally select it.
For arm the actual configuration determine if IDE is supported.
This is a step towards introducing drivers/Kconfig for arm.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Russell King - ARM Linux <linux@arm.linux.org.uk>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
PWM device setup, and a simple PWM driver exposing a programming interface
giving access to each channel's full capabilities. Note that this doesn't
support starting several channels in synch.
[hskinnemoen@atmel.com: allocate platform device dynamically]
[hskinnemoen@atmel.com: Kconfig fix]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sometimes simple attributes might need to return an error, e.g. for
acquiring a mutex interruptibly. In fact we have that situation in
spufs already which is the original user of the simple attributes. This
patch merged the temporarily forked attributes in spufs back into the
main ones and allows to return errors.
[akpm@linux-foundation.org: build fix]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: <stefano.brivio@polimi.it>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg KH <greg@kroah.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patchset adds a flags variable to reserve_bootmem() and uses the
BOOTMEM_EXCLUSIVE flag in crashkernel reservation code to detect collisions
between crashkernel area and already used memory.
This patch:
Change the reserve_bootmem() function to accept a new flag BOOTMEM_EXCLUSIVE.
If that flag is set, the function returns with -EBUSY if the memory already
has been reserved in the past. This is to avoid conflicts.
Because that code runs before SMP initialisation, there's no race condition
inside reserve_bootmem_core().
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix powerpc build]
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: <linux-arch@vger.kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- All implementations can be __devinit
- The function prototypes were in asm/timex.h but they all must be the same,
so create a single declaration in linux/timex.h.
- uninline the sparc64 version to match the other architectures
- Don't bother #defining ARCH_HAS_READ_CURRENT_TIMER to a particular value.
[ezk@cs.sunysb.edu: fix build]
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Teach AVR32 to use the "GPIO Library" when exposing its GPIOs, so that signals
on external chips (like GPIO expanders) can easily be used.
This mostly reorganizes some existing logic, with two minor changes in
behavior:
- The PSR registers are used instead of the previous "gpio_mask" values,
matching AT91 behavior and removing some duplication between that role
and that of "pinmux_mask".
- NR_IRQs grew to acommodate a bank of external GPIOs. Eventually this
number should probably become a board-specific config option.
There's a debugfs dump of status for the built-in GPIOs, showing which pins
have deglitching, pullups, or open drain drive enabled, as well as the ID
string used when requesting each IRQ.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Eric Miao <eric.miao@marvell.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
AVR32 still includes Kconfig.instrumentation, so it won't build after
this...
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus:
On the per-architecture side, I do think it would be better to *not* have
internal architecture knowledge in a generic file, and as such a line like
depends on X86_32 || IA64 || PPC || S390 || SPARC64 || X86_64 || AVR32
really shouldn't exist in a file like kernel/Kconfig.instrumentation.
It would be much better to do
depends on ARCH_SUPPORTS_KPROBES
in that generic file, and then architectures that do support it would just
have a
bool ARCH_SUPPORTS_KPROBES
default y
in *their* architecture files. That would seem to be much more logical,
and is readable both for arch maintainers *and* for people who have no
clue - and don't care - about which architecture is supposed to support
which interface...
Changelog:
Actually, I know I gave this as the magic incantation, but now that I see
it, I realize that I should have told you to just use
config KPROBES_SUPPORT
def_bool y
instead, which is a bit denser.
We seem to use both kinds of syntax for these things, but this is really
what "def_bool" is there for...
- Use HAVE_KPROBES
- Use a select
- Yet another update :
Moving to HAVE_* now.
- Update ARM for kprobes support.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Linus:
On the per-architecture side, I do think it would be better to *not* have
internal architecture knowledge in a generic file, and as such a line like
depends on X86_32 || IA64 || PPC || S390 || SPARC64 || X86_64 || AVR32
really shouldn't exist in a file like kernel/Kconfig.instrumentation.
It would be much better to do
depends on ARCH_SUPPORTS_KPROBES
in that generic file, and then architectures that do support it would just
have a
bool ARCH_SUPPORTS_KPROBES
default y
in *their* architecture files. That would seem to be much more logical,
and is readable both for arch maintainers *and* for people who have no
clue - and don't care - about which architecture is supposed to support
which interface...
Changelog:
Actually, I know I gave this as the magic incantation, but now that I see
it, I realize that I should have told you to just use
config ARCH_SUPPORTS_KPROBES
def_bool y
instead, which is a bit denser.
We seem to use both kinds of syntax for these things, but this is really
what "def_bool" is there for...
Changelog :
- Moving to HAVE_*.
- Add AVR32 oprofile.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
This patch consolidate all definitions of .init.text, .init.data
and .exit.text, .exit.data section definitions in
the generic vmlinux.lds.h.
This is a preparational patch - alone it does not buy
us much good.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
[AVR32] extint: Set initial irq type to low level
[AVR32] extint: change set_irq_type() handling
[AVR32] NMI debugging
[AVR32] constify function pointer tables
[AVR32] ATNGW100: Update defconfig
[AVR32] ATSTK1002: Update defconfig
[AVR32] Kconfig: Choose daughterboard instead of CPU
[AVR32] Add support for ATSTK1003 and ATSTK1004
[AVR32] Clean up external DAC setup code
[AVR32] ATSTK1000: Move gpio-leds setup to setup.c
[AVR32] Add support for AT32AP7001 and AT32AP7002
[AVR32] Provide more CPU information in /proc/cpuinfo and dmesg
[AVR32] Oprofile support
[AVR32] Include instrumentation menu
Disable VGA text console for AVR32 architecture
[AVR32] Enable debugging only when needed
ptrace: Call arch_ptrace_attach() when request=PTRACE_TRACEME
[AVR32] Remove redundant try_to_freeze() call from do_signal()
[AVR32] Drop GFP_COMP for DMA memory allocations
David Brownell pointed out a mismatch in the avr32 extint code:
> I noticed a small glitch that's not fixed by this patch: the
> initial type is falling edge, but IRQ_TYPE_NONE is mapped to
> IRQ_TYPE_LEVEL_LOW. Potentially surprising.
Fix it by setting the initial type (and handler) to low level,
matching the meaning of IRQ_TYPE_NONE.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Update the AVR32 EIC code to use the new __set_irq_handler_unlocked()
call, getting rid of one more instance of this widespread problem.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Change the NMI handler to use the die notifier chain to signal anyone
who cares. Add a simple "nmi debugger" which hooks into this chain and
that may dump registers, task state, etc. when it happens.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Remove the CPU selection menu and instead let it be selected by the
board or daughterboard option. Add daughterboard selection for
ATSTK1000 (this was previously determined based on CPU type.)
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
ATSTK1003 and ATSTK1004 are CPU daughterboards for ATSTK1000 featuring
the AT32AP7001 and AT32AP7002 CPUs, respectively.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Reduce the ridiculous amount of #ifdef clutter in atstk1002.c a bit by
moving all the extdac stuff into its own function and providing an
empty stub for the case when it isn't wanted.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
There may be other boards than STK1002 that want to use the leds on
STK1000. Move it to stk1000 common code to make it easier to reuse.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
These are derivatives of the AT32AP7000 chip, which means that most of
the code stays the same. Rename a few files, functions, definitions
and config symbols to reflect that they apply to all AP700x chips, and
exclude some platform devices from chips where they aren't present.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Add the following fields to /proc/cpuinfo:
* chip type and revision (from the JTAG chip id)
* cpu MHz (from clk_get_rate())
* features (from the CONFIG0 register)
Also rename "cpu family" to "cpu arch" and "cpu type" to "cpu core" to
remove some ambiguity.
Show chip type and revision at bootup, and clarify that the other
kinds of IDs that we're already printing are for the cpu core and
architecture. Rename "AP7000" to "AP7" since that's the name of the
core.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This adds the necessary architecture code to run oprofile on AVR32
using the performance counters documented by the AVR32 Architecture
Manual.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Philippe Elie <phil.el@wanadoo.fr>
Keep track of processes being debugged (including the kernel itself)
and turn the OCD system on and off as appropriate. Since enabling
debugging turns off some optimizations in the CPU core, this fixes the
issue that enabling KProbes support or simply running a program under
gdbserver will reduce system performance significantly until the next
reboot.
The CPU performance will still be reduced for all processes while a
process is being debugged, but this is a lot better than reducing the
performance forever.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
get_signal_to_deliver() will call try_to_freeze(), so there's no point
in do_signal() doing it as well.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
dma_alloc_coherent wants to split pages after allocation in order to
reduce the memory footprint. This does not work well with GFP_COMP
pages, so drop this flag before allocation.
This patch was forward-ported from BSP 2.0
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
All kobjects require a dynamically allocated name now. We no longer
need to keep track if the name is statically assigned, we can just
unconditionally free() all kobject names on cleanup.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's not like it really matters at this point since the system is
dying anyway, but handle_critical pushes too few registers on the
stack so the register dump, which makes the register dump look a bit
strange. This patch fixes it.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The current implementation of copy_to_user_page() gives "vaddr" to the
cache instruction when trying to sync the icache with the dcache. If
vaddr does not exist in the TLB, the CPU will silently abort the
operation, which may result in the caches staying out of sync.
To fix this, pass the "dst" parameter to flush_icache_range() instead
-- we know this is valid because we just wrote to it.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The current debug trap handling code does a number of things that are
illegal according to the AVR32 Architecture manual. Most importantly,
it may try to schedule from Debug Mode, thus clearing the D bit, which
can lead to "undefined behaviour".
It seems like this works in most cases, but several people have
observed somewhat unstable behaviour when debugging programs,
including soft lockups. So there's definitely something which is not
right with the existing code.
The new code will never schedule from Debug mode, it will always exit
Debug mode with a "retd" instruction, and if something not running in
Debug mode needs to do something debug-related (like doing a single
step), it will enter debug mode through a "breakpoint" instruction.
The monitor code will then return directly to user space, bypassing
its own saved registers if necessary (since we don't actually care
about the trapped context, only the one that came before.)
This adds three instructions to the common exception handling code,
including one branch. It does not touch super-hot paths like the TLB
miss handler.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Generate a new set of OCD register definitions in asm/ocd.h and rename
__mfdr() and __mtdr() to ocd_read() and ocd_write() respectively.
The bitfield definitions are a lot more complete now, and they are
entirely based on bit numbers, not masks. This is because OCD
registers are frequently accessed from assembly code, where bit
numbers are a lot more useful (can be fed directly to sbr, bfins,
etc.)
Bitfields that consist of more than one bit have two definitions:
_START, which indicates the number of the first bit, and _SIZE, which
indicates the number of bits. These directly correspond to the
parameters taken by the bfextu, bfexts and bfins instructions.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The 'H' bit is bit 29, while the 'R' bit doesn't exist. Luckily, we
don't actually use any of the bits in question.
Also update show_regs() to show the Debug Mask and Debug state bits.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Oprofile needs to call intc_get_pending() in order to determine
whether a performance counter interrupt is pending.
Also, include the header which declares intc_get_pending() and fix the
definition to match the prototype.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
There's a duplicate clock index between USART0 and USART1 which may be
causing system crashes when USART0 is used. Change the USART0 index
to '3', indicating the clock that is actually used by USART0.
Signed-off-by: Ben Nizette <ben@niasdigital.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
avr32 already sees the option from init/Kconfig.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This patch extends the I/O resource to 0xfff000cf which will enable the
watchdog driver to access the reset cause (RCAUSE) register. Making it
capable of reporting boot status.
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Implement at32_add_device_cf() which will add a platform_device for
the at32_cf driver (not merged yet). Separate out most of the
at32_add_device_ide() code and use it to implement
at32_add_device_cf() as well.
This changes the API in the following ways:
* The board code must initialize data->cs to the chipselect ID to
use before calling any of these functions.
* The board code must use GPIO_PIN_NONE to indicate unused CF pins.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Implement functions for adding platform devices for TWI, MCI, AC97C
and ABDAC. They may need to be modified to cope with platform data,
etc. when the corresponding drivers are ready to be merged, but such
changes are much less likely to conflict than adding support for a
whole new type of device.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This patch adds platform code for PATA devices on the AP7000.
[hskinnemoen@atmel.com: board code left out for now since stk1000
doesn't support IDE out of the box]
Signed-off-by: Kristoffer Nyborg Gregertsen <kngregertsen@norway.atmel.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Most of these fixes were already submitted for old kernel versions, and were
approved, but for some reason they never made it into the releases.
Because this is a consolidation of a couple old missed patches, it touches both
Kconfigs and documentation texts.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
is_init() is an ambiguous name for the pid==1 check. Split it into
is_global_init() and is_container_init().
A cgroup init has it's tsk->pid == 1.
A global init also has it's tsk->pid == 1 and it's active pid namespace
is the init_pid_ns. But rather than check the active pid namespace,
compare the task structure with 'init_pid_ns.child_reaper', which is
initialized during boot to the /sbin/init process and never changes.
Changelog:
2.6.22-rc4-mm2-pidns1:
- Use 'init_pid_ns.child_reaper' to determine if a given task is the
global init (/sbin/init) process. This would improve performance
and remove dependence on the task_pid().
2.6.21-mm2-pidns2:
- [Sukadev Bhattiprolu] Changed is_container_init() calls in {powerpc,
ppc,avr32}/traps.c for the _exception() call to is_global_init().
This way, we kill only the cgroup if the cgroup's init has a
bug rather than force a kernel panic.
[akpm@linux-foundation.org: fix comment]
[sukadev@us.ibm.com: Use is_global_init() in arch/m32r/mm/fault.c]
[bunk@stusta.de: kernel/pid.c: remove unused exports]
[sukadev@us.ibm.com: Fix capability.c to work with threaded init]
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Acked-by: Pavel Emelianov <xemul@openvz.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: Herbert Poetzel <herbert@13thfloor.at>
Cc: Kirill Korotaev <dev@sw.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dma_cache_(wback|inv|wback_inv) were the earliest attempt on a generalized
cache managment API for I/O purposes. Originally it was basically the raw
MIPS low level cache API exported to the entire world. The API has
suffered from a lack of documentation, was not very widely used unlike it's
more modern brothers and can easily be replaced by dma_cache_sync. So
remove it rsp. turn the surviving bits back into an arch private API, as
discussed on linux-arch.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Paul Mackerras <paulus@samba.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Kyle McMartin <kyle@parisc-linux.org>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (40 commits)
kbuild: introduce ccflags-y, asflags-y and ldflags-y
kbuild: enable 'make CPPFLAGS=...' to add additional options to CPP
kbuild: enable use of AFLAGS and CFLAGS on commandline
kbuild: enable 'make AFLAGS=...' to add additional options to AS
kbuild: fix AFLAGS use in h8300 and m68knommu
kbuild: check for wrong use of CFLAGS
kbuild: enable 'make CFLAGS=...' to add additional options to CC
kbuild: fix up CFLAGS usage
kbuild: make modpost detect unterminated device id lists
kbuild: call export_report from the Makefile
kbuild: move Kai Germaschewski to CREDITS
kconfig/menuconfig: distinguish between selected-by-another options and comments
kconfig: tristate choices with mixed tristate and boolean values
include/linux/Kbuild: remove duplicate entries
kbuild: kill backward compatibility checks
kbuild: kill EXTRA_ARFLAGS
kbuild: fix documentation in makefiles.txt
kbuild: call make once for all targets when O=.. is used
kbuild: pass -g to assembler under CONFIG_DEBUG_INFO
kbuild: update _shipped files for kconfig syntax cleanup
...
Fix up conflicts in arch/um/sys-{x86_64,i386}/Makefile manually.
Introduce architecture dependent kretprobe blacklists to prohibit users
from inserting return probes on the function in which kprobes can be
inserted but kretprobes can not.
This patch also removes "__kprobes" mark from "__switch_to" on x86_64 and
registers "__switch_to" to the blacklist on x86-64, because that mark is to
prohibit user from inserting only kretprobe.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Acked-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have had complaints where a threaded application is left in a bad state
after one of it's threads is killed when we hit a VM: out_of_memory
condition.
Killing just one of the process threads can leave the application in a bad
state, whereas killing the entire process group would allow for the
application to restart, or be otherwise handled, and makes it very obvious
that something has gone wrong.
This change allows the entire process group to be taken down, rather
than just the one thread.
Signed-off-by: Will Schmidt <will_schmidt@vnet.ibm.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Andi Kleen <ak@suse.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Wilcox <willy@debian.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Identical handlers of PTRACE_DETACH go into ptrace_request().
Not touching compat code.
Not touching archs that don't call ptrace_request.
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The variable AFLAGS is a wellknown variable and the usage by
kbuild may result in unexpected behaviour.
On top of that several people over time has asked for a way to
pass in additional flags to gcc.
This patch replace use of AFLAGS with KBUILD_AFLAGS all over
the tree.
Patch was tested on following architectures:
alpha, arm, i386, x86_64, mips, sparc, sparc64, ia64, m68k, s390
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
The variable CFLAGS is a wellknown variable and the usage by
kbuild may result in unexpected behaviour.
On top of that several people over time has asked for a way to
pass in additional flags to gcc.
This patch replace use of CFLAGS with KBUILD_CFLAGS all over the
tree and enabling one to use:
make CFLAGS=...
to specify additional gcc commandline options.
One usecase is when trying to find gcc bugs but other
use cases has been requested too.
Patch was tested on following architectures:
alpha, arm, i386, x86_64, mips, sparc, sparc64, ia64, m68k
Test was simple to do a defconfig build, apply the patch and check
that nothing got rebuild.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
As explained on:
http://www.avrfreaks.net/index.php?nameÿphpBB2&fileÿewtopic&tS307
If the current process is preempted before it can copy RAR_SUP and
RSR_SUP both register are lost and the process will segfault as soon
as it return from the syscall since the return adress will be
corrupted.
This patch disable IRQ as soon as we enter the syscall path and
reenable them when the copy is done.
In the interrupt handlers, check if we are interrupting the srrf
instruction, if so disable interrupts and return. The interrupt
handler will be re-called immediatly when the interrupts are
reenabled.
After some stressing workload:
- find / > /dev/null in loop
- top (in ssh)
- ping -f avr32
The segfaults are not seen anymore.
Signed-off-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Make the NGW100 bitbang i2c use open drain signaling.
Also, speed it up, so it's closer to 100 kHz ... the code paths seem
to be long enough that the udelay isn't dominating bit times. The
peak bit rate I observed was around 125 kHz, but that's with large
delays (usually before ACK/NAK) which hold the overall rate down to
around 80 kHz (call it 100 usec/byte on average).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This patch makes the SMC configuration take timings in clock cycles
instead of nanoseconds. A function to calculate timings in clock
cycles is added.
This patch removes the rounding troubles of the previous SMC
configuration method.
[hskinnemoen@atmel.com: fix atstk1002/atngw100 flash config]
Signed-off-by: Kristoffer Nyborg Gregertsen <gregerts@stud.ntnu.no>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Given the existing "retain_initrd" boot-time parameter defined in
init/initramfs.c, there appears to be no need for the equivalent
"keepinitrd" parameter.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
__init_end, which comes immediately before .text, is already page
aligned, and that should be more than enough for the .text section.
The reason why we need to align the .text section is because the
interrupt handler offset is ORed with EVBA, so we need to provide
enough alignment of EVBA that this OR operation works as an ADD.
Currently, the last interrupt handler is not nearly a full page away
from EVBA, so it won't be a problem.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Use PAGE_SIZE, THREAD_SIZE and L1_CACHE_BYTES instead of harcoded
constants in places where that's what we really mean.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Rename vmlinux.lds to a .S file to match other architectures.
Simplify Makefile to match the rename and deleted the unused
USE_STANDARD_AS_RULE
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Implement at32_add_device_usba() and use it to wire up the USBA device
on ATSTK1000 and ATNGW100.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This patch add multidrive support for pio driver
Signed-off-by: Matteo Vit - Dave S.r.l. <matteo.vit@dave.eu>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
When debugfs is available, /sys/kernel/debug/at32ap_clk will provide a
dump of the power manager registers and of the current clock tree. This
can help sorting out various surprises, and when making runtime PM work.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The NGW100 has a board controller which is hooked up to the TWI lines
on AP7000. Since the TWI driver isn't in mainline, use the i2c-gpio
driver in the mean time.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Add GPIO led support: J2 to either block of LEDs on the STK1000.
This uses the new LEDS_GPIO driver, and sets up a heartbeat trigger by
default ... either bright (!!) amber, or a more interesting purple.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
leds: Convert from struct class_device to struct device
leds: leds-gpio for ngw100
leds: Add warning printks in error paths
leds: Fix trigger unregister_simple if register_simple fails
leds: Use menuconfig objects II - LED
leds: Teach leds-gpio to handle timer-unsafe GPIOs
leds: Add generic GPIO LED driver
This patch completes Linus's wish that the fault return codes be made into
bit flags, which I agree makes everything nicer. This requires requires
all handle_mm_fault callers to be modified (possibly the modifications
should go further and do things like fault accounting in handle_mm_fault --
however that would be for another patch).
[akpm@linux-foundation.org: fix alpha build]
[akpm@linux-foundation.org: fix s390 build]
[akpm@linux-foundation.org: fix sparc build]
[akpm@linux-foundation.org: fix sparc64 build]
[akpm@linux-foundation.org: fix ia64 build]
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Matthew Wilcox <willy@debian.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Chris Zankel <chris@zankel.net>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ Still apparently needs some ARM and PPC loving - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The STK1000 uses pullups on the MDIO lines to the PHY, but they are
too weak. This causes the PHY layer to detect PHYs on all possible MII
addresses. Mask out all but the correct address to prevent this from
happening.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This code is inside an #ifdef with a misspelled config symbol, so it
hasn't been used for a long time. Fix it before fixing the config
symbol to keep bisection working.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This patch adds register definitions, clocks and IRQs to the platform devices.
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This adds some STK1002-specific config options covering the jumper settings,
so the kernel can automatically be configured to include the relevant devices.
One of them replaces the previous internal SW2_DEFAULT setting; SPI config
is affected by two of the jumpers; and a fourth one switches between LCD and
the second Ethernet connector. (There's more that to be done.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This patch enables CPU frequency scaling for AT32AP devices. This will
enable the CPU to scale between the speed of the high speed bus and
the master clock and thus save some power.
The patch also adds a parent to cpu_clk and a cpu_clk_set_rate to
enable changing the CPU clock divider in a sane way.
The driver does not check if the given rate is 0, thus resulting in a
div by 0. I think this check should be go into the clk_set_rate
framework, and not here.
Tested on AT32AP7000/ATSTK1000.
Hardware documentation can be found in the AT32AP7000 datasheet.
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Split the SM platform device into separate platform devices for PM,
RTC, WDT and EIC. This is more correct according to the documentation
and allows us to simplify the code a little.
Also turn the EIC driver into a real platform driver.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Identical implementations of PTRACE_POKEDATA go into generic_ptrace_pokedata()
function.
AFAICS, fix bug on xtensa where successful PTRACE_POKEDATA will nevertheless
return EPERM.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the kernel OOPSed or BUGed then it probably should be considered as
tainted. Thus, all subsequent OOPSes and SysRq dumps will report the
tainted kernel. This saves a lot of time explaining oddities in the
calltraces.
Signed-off-by: Pavel Emelianov <xemul@openvz.org>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ Added parisc patch from Matthew Wilson -Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current generic bug implementation has a call to dump_stack() in case a
WARN_ON(whatever) gets hit. Since report_bug(), which calls dump_stack(),
gets called from an exception handler we can do better: just pass the
pt_regs structure to report_bug() and pass it to show_regs() in case of a
warning. This will give more debug informations like register contents,
etc... In addition this avoids some pointless lines that dump_stack()
emits, since it includes a stack backtrace of the exception handler which
is of no interest in case of a warning. E.g. on s390 the following lines
are currently always present in a stack backtrace if dump_stack() gets
called from report_bug():
[<000000000001517a>] show_trace+0x92/0xe8)
[<0000000000015270>] show_stack+0xa0/0xd0
[<00000000000152ce>] dump_stack+0x2e/0x3c
[<0000000000195450>] report_bug+0x98/0xf8
[<0000000000016cc8>] illegal_op+0x1fc/0x21c
[<00000000000227d6>] sysc_return+0x0/0x10
Acked-by: Jeremy Fitzhardinge <jeremy@goop.org>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Kyle McMartin <kyle@parisc-linux.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add GPIO leds to the NGW100 platform and its defconfig.
Access through /sys/class/leds/{a,b,sys}/* files; one
defaults to a heartbeat.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Update defconfigs for ATNGW100 and ATSTK1002. This will enable the
SLUB allocator by default on both, and will enable NFS root on
ATSTK1002 (ATNGW100 had it enabled before.)
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The current at32ap7000 platform devices aren't declared as supporting DMA,
so that layered drivers can't tell whether they need to manage DMA.
This patch makes all those platform devices report that they support DMA.
Most do, but in a few cases this is inappropriate.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
USART mapping used to be accomplished by the manual filling of
at32_usart_map[] and at32_nr_usarts. This has now been replaced
with at32_map_usart() so we can remove these variables.
Signed-off-by: Ben Nizette <ben.nizette@iinet.net.au>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
If (start + size) is not cacheline aligned and (start & mask) > (end &
mask), the last but one cacheline won't be invalidated as it should.
Fix this by rounding `end' down to the nearest cacheline boundary if
it gets adjusted due to misalignment.
Also flush the write buffer unconditionally -- if the dcache wrote
back a line just before we invalidated it, the dirty data may be
sitting in the write buffer waiting to corrupt our buffer later.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
In the latest incarnation of the ltv350qv driver the call to
spi_setup() has been removed. So we need to initialize things more
carefully in the board info struct.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Limit the rate of the kernel logging for the segfaults of user
applications, to avoid potential message floods or denial-of-service
attacks.
Signed-off-by: Andrea Righi <a.righi@cineca.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This modifies and extends the existing lcdc platform code to support
the new atmel_lcdfb driver. The ATSTK1000 board code is set up to use
the on-board Samsung LTV350QV LCD panel.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Avoid the costly notifier list in the pagefault path and call
the kprobes code directly. The same change went into the 2.6.22
cycle for powerpc, 2s390 and sparc64 already.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The comment at the top of arch/avr32/kernel/irq.c doesn't really make
sense anymore since most of the actual interrupt handling code is
elsewhere.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Recently a few direct accesses to the thread_info in the task structure snuck
back, so this wraps them with the appropriate wrapper.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested with a slightly hacked version of the test case included with
the original utimensat patch. All OK.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Rename .taglist to .taglist.init to silence section mismatch warnings.
The .taglist.init section was already placed in the .init output
section along with .init.text, so the warning didn't indicate any real
problems.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Implement dma_alloc_writecombine() and its dma_free_writecombine()
counterpart. These will do basically the same thing as
dma_alloc_coherent() except that the virtual mapping will allow
write buffering, causing better performance for certain use cases
like frame buffers.
The same API is already available on ARM.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
As Robert P. J. Day pointed out, the CONFIG_CPU_AT32AP7000 symbol
wasn't used for anything. It should have been used to select the
correct -mcpu= options for CFLAGS.
-mcpu=ap7000 is the default anyway, so this patch shouldn't really
make any difference, but it's always nice to do things correctly.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Remove includes of <linux/smp_lock.h> where it is not used/needed.
Suggested by Al Viro.
Builds cleanly on x86_64, i386, alpha, ia64, powerpc, sparc,
sparc64, and arm (all 59 defconfigs).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch moves the die notifier handling to common code. Previous
various architectures had exactly the same code for it. Note that the new
code is compiled unconditionally, this should be understood as an appel to
the other architecture maintainer to implement support for it aswell (aka
sprinkling a notify_die or two in the proper place)
arm had a notifiy_die that did something totally different, I renamed it to
arm_notify_die as part of the patch and made it static to the file it's
declared and used at. avr32 used to pass slightly less information through
this interface and I brought it into line with the other architectures.
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix vmalloc_sync_all bustage]
[bryan.wu@analog.com: fix vmalloc_sync_all in nommu]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: <linux-arch@vger.kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the clearly useless config option GENERIC_BUST_SPINLOCK, which
is not used anywhere in the tree.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Reorder some instructions and change the register usage to reduce
the number of pipeline stalls. Also use the bfextu and bfins
instructions for bitfield manipulations instead of shifting and
masking.
This makes gzipping a 80MB file approximately 2% faster.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Since the core setup code takes care of both allocation and
reservation of framebuffer memory, there's no need for this board-
specific hook anymore. Replace it with two global variables,
fbmem_start and fbmem_size, which can be used directly.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
With the current strategy of using the bootmem allocator to allocate
or reserve framebuffer memory, there's a slight chance that the
requested area has been taken by the boot allocator bitmap before we
get around to reserving it.
By inserting the framebuffer region as a reserved region as early as
possible, we improve our chances for success and we make the region
visible as a reserved region in dmesg and /proc/iomem without any
extra work.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Use struct resource to specify both physical memory regions and
reserved regions and push everything into the same framework,
including kernel code/data and initrd memory. This allows us to get
rid of many special cases in the bootmem initialization and will also
make it easier to implement more robust handling of framebuffer
memory later.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Fix the I/O access macros so that they work with externally connected
devices accessed in little-endian mode over any bus width:
* Use a set of macros to define I/O port- and memory operations
borrowed from MIPS.
* Allow subarchitecture to specify address- and data-mangling
* Implement at32ap-specific port mangling (with build-time
configurable bus width. Only one bus width at a time supported
for now.)
* Rewrite iowriteN and friends to use write[bwl] and friends
(not the __raw counterparts.)
This has been tested using pata_pcmcia to access a CompactFlash card
connected to the EBI (16-bit bus width.)
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Fix a problem with the NMI handler entry code related to the NMI handler
sharing some code with the exception handlers. This is not a good idea
because the RSR and RAR registers are not the same, and the NMI handler
runs with interrupts masked the whole time so there's no need to check
for pending work.
Open-code the low-level NMI handling logic instead so that the pt_regs
layout is actually correct when the higher-level handler is called.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
* Use generic BUG() handling
* Remove some useless debug statements
* Use a common function _exception() to send signals or oops when
an exception can't be handled. This makes sure init doesn't
enter an infinite exception loop as well. Borrowed from powerpc.
* Add some basic exception tracing support to the page fault code.
* Rework dump_stack(), show_regs() and friends and move everything
into process.c
* Print information about configuration options and chip type when
oopsing
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Clean up the cpu identification code, using definitions from
<asm/sysreg.h> instead of hardcoded constants. Also, add a features
bitmap to struct avr32_cpuinfo to allow other code to make decisions
based upon what the running cpu is actually capable of.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Bring the code that sets the initial PM clock masks in line with the
comment preceding it by only enabling clocks that have users != 0.
Fix SM clock definition and avr32_hpt_init() so that the SM and TC0
clocks keep ticking.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This patch puts the CPU in sleep 0 when doing nothing, idle. This will
turn of the CPU clock and thus save power. The CPU is waken again when
an interrupt occurs.
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Due to limitation of the count-compare system timer (not able to
count when CPU is in sleep), the system timer had to be changed to
use a peripheral timer/counter.
The old COUNT-COMPARE code is still present in time.c as weak
functions. The new timer is added to the architecture directory.
This patch sets up TC0 as system timer The new timer has been tested
on AT32AP7000/ATSTK1000 at 100 Hz, 250 Hz, 300 Hz and 1000 Hz.
For more details about the timer/counter see the datasheet for
AT32AP700x available at
http://www.atmel.com/dyn/products/product_card.asp?part_id=3903
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Include at32ap-specific Kconfig file from top-level Kconfig file. The
at32ap Kconfig is currently empty, but it will grow some machine-
specific options soon.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Complete the SMC configuration code by adding nwait and tdf
parameter. After this change, we support the same parameters as the
hardware.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This adds register and clock definitions for the High-speed bus Matrix
(HMATRIX) as well as a function that can be used to configure special
EBI functionality like CompactFlash and NAND flash support.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
It's been pointed out that output GPIOs should have an initial value, to
avoid signal glitching ... among other things, it can be some time before
a driver is ready. This patch corrects that oversight, fixing
- documentation
- platforms supporting the GPIO interface
- users of that call (just one for now, others are pending)
There's only one user of this call for now since most platforms are still
using non-generic GPIO setup code, which in most cases already couples the
initial value with its "set output mode" request.
Note that most platforms are clear about the hardware letting the output
value be set before the pin direction is changed, but the s3c241x docs are
vague on that topic ... so those chips might not avoid the glitches.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Acked-by: Milan Svoboda <msvoboda@ra.rockwell.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
flush_icache_page() can be called from atomic context, so we can't
use kmap(). Use page_address() instead.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
We should OR in a bitmask, not a bit offset, into ti->flags. This
might fix some strange behaviour when single stepping.
Also, use set_ti_thread_flag() to manipulate the flags to avoid
surprises in the future.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Terminate the frame pointer walk if (a) the address is outside the
task's kernel stack or (b) if the frame pointer isn't monotonically
increasing. Without this fix, show_trace() may enter an infinite
loop, walking through random data anywhere in memory.
Since any address within the kernel stack is guaranteed to be valid,
we may eliminate the __get_user() calls as well.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Most drivers using GPIOs already know they are running on a system that
supports the generic GPIO calls, because of other platform dependencies.
But the generic GPIO-based LED and input button drivers can't know that.
So this patch adds a Kconfig hook, GENERIC_GPIO, to mark the platforms
where <asm/gpio.h> will do the right thing. Currently that's a bunch of
ARMs, and AVR32; more are on the way.
It also fixes a dependency bug for the gpio button input driver; it was
wrong to start with, now it covers all platforms with GENERIC_GPIO.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: <raph@8d.com>
Cc: <msvoboda@ra.rockwell.com>
Cc: pHilipp Zabel <philipp.zabel@gmail.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (117 commits)
[ARM] 4058/2: iop32x: set ->broken_parity_status on n2100 onboard r8169 ports
[ARM] 4140/1: AACI stability add ac97 timeout and retries
[ARM] 4139/1: AACI record support
[ARM] 4138/1: AACI: multiple channel support for IRQ handling
[ARM] 4211/1: Provide a defconfig for ns9xxx
[ARM] 4210/1: base for new machine type "NetSilicon NS9360"
[ARM] 4222/1: S3C2443: Remove reference to missing S3C2443_PM
[ARM] 4221/1: S3C2443: DMA support
[ARM] 4220/1: S3C24XX: DMA system initialised from sysdev
[ARM] 4219/1: S3C2443: DMA source definitions
[ARM] 4218/1: S3C2412: fix CONFIG_CPU_S3C2412_ONLY wrt to S3C2443
[ARM] 4217/1: S3C24XX: remove the dma channel show at startup
[ARM] 4090/2: avoid clash between PXA and SA1111 defines
[ARM] 4216/1: add .gitignore entries for ARM specific files
[ARM] 4214/2: S3C2410: Add Armzone QT2410
[ARM] 4215/1: s3c2410 usb device: per-platform vbus_draw
[ARM] 4213/1: S3C2410 - Update definition of ADCTSC_XY_PST
[ARM] 4098/1: ARM: rtc_lock only used with rtc_cmos
[ARM] 4137/1: Add kexec support
[ARM] 4201/1: SMP barriers pair needed for the secondary boot process
...
Fix up conflict due to typedef removal in sound/arm/aaci.h
* 'for-linus' of git://www.atmel.no/~hskinnemoen/linux/kernel/avr32:
[AVR32] Use per-controller spi_board_info structures
[AVR32] Warn, don't BUG if clk_disable is called too many times
[AVR32] Make sure all genclocks have a parent
[AVR32] Remove unnecessary sys_nfsservctl conditional
[AVR32] Wire up the SysV IPC calls properly
[AVR32] Define ioremap_nocache, ioport_map and ioport_unmap
[AVR32] Fix prototypes for __raw_writesb and friends
Fixup the is_contionous replacement by a flag field.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Set up one spi_board_info array per controller and pass this to
at32_add_device_spi so that it can set up any GPIO pins for chip
selects based on this information.
Extracted from a patch by David Brownell and adapted slightly.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Print a helpful warning along with a stack dump if clk_disable is
called on a already-disabled clock. Remove the BUG_ON().
Extracted from a patch by David Brownell.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Initialize the parent field of each generic clock by looking at the
PM registers. This means that the genclock operations can always
assume that the parent field is non-null, so they don't have to
check. Also remove a few unnecessary BUG_ON()s.
Extracted from a patch by David Brownell.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
kernel/sys_ni.c defines sys_nfsservctl as a weak alias for
sys_ni_syscall, so it's always safe to include it in the system
call table.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Wire up the individual sysvipc system calls and remove sys_ipc.
Strictly speaking, this breaks the ABI, but since sys_ipc never
worked anyway due to a silly bug, it isn't actually a regression.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
[akpm@osdl.org: sparc64 fix]
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update all arch/*/kernel/vmlinux.lds.S to not include space for initramfs
when CONFIG_BLK_DEV_INITRAMFS is not selected. This saves another 4 kbytes
on most platfoms (some reserve PAGE_SIZE for initramfs).
Signed-off-by: Jean-Paul Saman <jean-paul.saman@nxp.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Two libgcc headers were left around even though all the actual code
borrowed from libgcc is gone. Delete them.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Move stuff in spi.c into ATSTK1002 board code and update SPI
platform device definitions according to the new GPIO API.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The PIOE device was left out before because it muxes SDRAM pins (and
is therefore a bit dangerous to mess with) and because no existing
drivers had any use for it.
It is needed for CompactFlash, however, and now that we have a way
to protect the SDRAM pins, it can be safely added.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
at32_reserve_pin() can be used for reserving portmux pins without
altering their configuration. Useful for e.g. SDRAM pins where we
really don't want to change the bootloader-provided configuration.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Leave the PIO lines as the bootloader left them. This allows us to
use PIOE without disturbing the SDRAM muxing.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
A patch to use ARRAY_SIZE macro already defined in linux/kernel.h
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Fix bug in dma_map_single(..., DMA_FROM_DEVICE) caused by incorrect
invalidation of shared cachelines at the beginning and/or end of
the specified buffer. Those shared cachelines need to be flushed,
since they may hold valid data (which must not be discarded).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Bugfixes for external irq handler set_irq_type():
- If set_irq_type() can't set the type, don't change anything!
- It's not OK to change the flow handler as part of set_irq_type(),
among other issues that violates spinlock rules. Instead, we can
call the relevant handler when we demux the external interrupts.
- The external irq demux has no need to grab the spinlock. And in
fact grabbing it that way was wrong, since that code might be
pre-empted by an irq at a different priority level, and that code
might then have tried to grab that spinlock...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Fixes to USART setup on the stk-1000 ... don't configure USART 2, since
its TXD/RXD are used for INT-A and INT-B buttons; and configure USART 0
(for IRDA, and with corrected IRQ) iff SW2 has a non-default setting.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The /proc/interrupts file should also display the irq_chip associated
with each irq ... e.g. INTC, EIM, GPIO.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Now that Linux includes support for the Atmel AT91SAM9260 and
AT91SAM9261 processors in addition to the original Atmel AT91RM9200
(with support for more AT91 processors pending), the "mach-at91rm9200"
and "arch-at91rm9200" directories should be renamed to indicate their
more generic nature.
The following git commands should be run BEFORE applying this patch:
git-mv arch/arm/mach-at91rm9200 arch/arm/mach-at91
git-mv include/asm-arm/arch-at91rm9200 include/asm-arm/arch-at91
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://www.atmel.no/~hskinnemoen/linux/kernel/avr32:
[AVR32] Add missing #include <linux/param.h> to delay.c
[AVR32] Pass dev parameter to dma_cache_sync()
[AVR32] Implement intc_get_pending()
[AVR32] Don't include <asm/delay.h>
[AVR32] Put the chip in "stop" mode when halting the system
[AVR32] Set flow handler for external interrupts
[AVR32] Remove unused file
[AVR32] Remove mii_phy_addr and eth_addr from eth_platform_data
[AVR32] Move ethernet tag parsing to board-specific code
[AVR32] Add macb1 platform_device
[AVR32] Portmux API update
This facility provides three entry points:
ilog2() Log base 2 of unsigned long
ilog2_u32() Log base 2 of u32
ilog2_u64() Log base 2 of u64
These facilities can either be used inside functions on dynamic data:
int do_something(long q)
{
...;
y = ilog2(x)
...;
}
Or can be used to statically initialise global variables with constant values:
unsigned n = ilog2(27);
When performing static initialisation, the compiler will report "error:
initializer element is not constant" if asked to take a log of zero or of
something not reducible to a constant. They treat negative numbers as
unsigned.
When not dealing with a constant, they fall back to using fls() which permits
them to use arch-specific log calculation instructions - such as BSR on
x86/x86_64 or SCAN on FRV - if available.
[akpm@osdl.org: MMC fix]
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David Howells <dhowells@redhat.com>
Cc: Wojtek Kaniewski <wojtekka@toxygen.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
intc_get_pending() returns a bitmask with pending interrupts in a
interrupt controller group (irq). This is used by the upcoming
oprofile implementation for avr32 and may also be useful for chained
interrupt controller drivers.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Make machine_halt() execute a sleep instruction to put the chip in
"stop" mode when the system is halted. This switches off all clocks
except the 32 kHz oscillator, which is needed for the RTC to keep
ticking.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Make sure that the flow handler for external interrupts is updated
whenever they type is changed. Also make sure that the defaults
correspond with how the interrupt controller is configured.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The macb driver will probe for the PHY chip and read the mac address
from the MACB registers, so we don't need them in eth_platform_data
anymore.
Since u-boot doesn't currently initialize the MACB registers with the
mac addresses, the tag parsing code is kept but instead of sticking
the information into eth_platform_data, it uses it to initialize
the MACB registers (in case the boot loader didn't do it.) This code
should be unnecessary at some point in the future.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
By moving the ethernet tag parsing to the board-specific code we avoid
the issue of figuring out which device we're supposed to attach the
information to. The board specific code knows this because it's
where the actual devices are instantiated.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Add platform_device definition and pio init code for the second
ethernet controller in AT32AP7000.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
