1. Optimize the match rules with new macro for Huawei USB storage devices,
to avoid to load USB storage driver for the modem interface
with Huawei devices.
2. Add to support new switch command for new Huawei USB dongles.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. Define a new macro for USB storage match rules:
matching with Vendor ID and interface descriptors.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add PID/VID entries for ELV WS 300 PC II weather station
Signed-off-by: Sven Killig <sven@killig.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds support for the OWL CM-160 electricity monitor to the cp210x
driver.
Signed-off-by: Luis Llorente <luisllorente@luisllorente.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1654) fixes a very old bug in ehci-hcd, connected with
scheduling of periodic split transfers. The calculations for
full/low-speed bus usage are all carried out after the correction for
bit-stuffing has been applied, but the values in the max_tt_usecs
array assume it hasn't been. The array should allow for allocation of
up to 90% of the bus capacity, which is 900 us, not 780 us.
The symptom caused by this bug is that any isochronous transfer to a
full-speed device with a maxpacket size larger than about 980 bytes is
always rejected with a -ENOSPC error.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1653) fixes a bug in ehci-hcd. Unlike iTD entries, an
siTD entry in the periodic schedule may not complete until the frame
after the one it belongs to. Consequently, when scanning the periodic
schedule it is necessary to start with the frame _preceding_ the one
where the previous scan ended.
Not doing this properly can result in memory leaks and failures to
complete isochronous URBs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Andy Leiserson <andy@leiserson.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1652) fixes a long-standing bug in ehci-hcd. The driver
relies on status polls to know when to stop port-resume signalling.
It uses the root-hub status timer to schedule these status polls. But
when the driver for the root hub is resumed, the timer is rescheduled
to go off immediately -- before the port is ready. When this happens
the timer does not get re-enabled, which prevents the port resume from
finishing until some other event occurs.
The symptom is that when a new device is plugged in, it doesn't get
recognized or enumerated until lsusb is run or something else happens.
The solution is to re-enable the root-hub status timer after every
status poll while a port resume is in progress.
This bug hasn't surfaced before now because we never used to try to
suspend the root hub in the middle of a port resume (except by
coincidence).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Norbert Preining <preining@logic.at>
Tested-by: Ming Lei <ming.lei@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1651) adds calls to the new
usb_hcd_{start,end}_port_resume() functions to uhci-hcd. Now UHCI
root hubs won't be runtime suspended while they are sending a resume
signal to one of their ports.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1650) adds calls to the new
usb_hcd_{start,end}_port_resume() functions to ehci-hcd. Now EHCI
root hubs won't be runtime suspended while they are sending a resume
signal to one of their ports.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1649) adds a mechanism for host controller drivers to
inform usbcore when they have begun or ended resume signalling on a
particular root-hub port. The core will then make sure that the root
hub does not get runtime-suspended while the port resume is going on.
Since commit 596d789a21 (USB: set hub's
default autosuspend delay as 0), the system tries to suspend hubs
whenever they aren't in use. While a root-hub port is being resumed,
the root hub does not appear to be in use. Attempted runtime suspends
fail because of the ongoing port resume, but the PM core just keeps on
trying over and over again. We want to prevent this wasteful effort.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1648) fixes a regression affecting nVidia EHCI
controllers. Evidently they don't like to have more than one async QH
unlinked at a time. I can't imagine how they manage to mess it up,
but at least one of them does.
The patch changes the async unlink logic in two ways:
Each time an IAA cycle is started, only the first QH on the
async unlink list is handled (rather than all of them).
Async QHs do not all get unlinked as soon as they have been
empty for long enough. Instead, only the last one (i.e., the
one that has been on the schedule the longest) is unlinked,
and then only if no other unlinks are in progress at the time.
This means that when multiple QHs are empty, they won't be unlinked as
quickly as before. That's okay; it won't affect correct operation of
the driver or add an excessive load. Multiple unlinks tend to be
relatively rare in any case.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Piergiorgio Sartor <piergiorgio.sartor@nexgo.de>
Cc: stable <stable@vger.kernel.org> # 3.6
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1647) attempts to work around a problem that seems to
affect some nVidia EHCI controllers. They sometimes take a very long
time to turn off their async or periodic schedules. I don't know if
this is a result of other problems, but in any case it seems wise not
to depend on schedule enables or disables taking effect in any
specific length of time.
The patch removes the existing 20-ms timeout for enabling and
disabling the schedules. The driver will now continue to poll the
schedule state at 1-ms intervals until the controller finally decides
to obey the most recent command issued by the driver. Just in case
this hides a problem, a debugging message will be logged if the
controller takes longer than 20 polls.
I don't know if this will actually fix anything, but it can't hurt.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Piergiorgio Sartor <piergiorgio.sartor@nexgo.de>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hi Greg,
Here's six patches for xHCI and the USB core. There's a couple of
patches to fix xHCI 1.0 field formats, some memory leaks, dead ports,
and USB 3.0 remote wakeup disabling.
All of these are marked for stable.
I know I owe you some re-works of failed stable patches from my last
patchset round, but I don't think I'm going to get to them before I head
off to Linux Conf Australia tomorrow.
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=rgLf
-----END PGP SIGNATURE-----
Merge tag 'for-usb-linus-2012-01-24' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus
Sarah writes:
USB/xhci: Misc fixes for 3.8.
Hi Greg,
Here's six patches for xHCI and the USB core. There's a couple of
patches to fix xHCI 1.0 field formats, some memory leaks, dead ports,
and USB 3.0 remote wakeup disabling.
All of these are marked for stable.
I know I owe you some re-works of failed stable patches from my last
patchset round, but I don't think I'm going to get to them before I head
off to Linux Conf Australia tomorrow.
Sarah Sharp
Here's a long-pending fixes pull request for arm-soc (I didn't send one
in the -rc4 cycle).
The larger deltas are from:
- A fixup of error paths in the mvsdio driver
- Header file move for a driver that hadn't been properly converted to
multiplatform on i.MX, which was causing build failures when included
- Device tree updates for at91 dealing mostly with their new
pinctrl setup merged in 3.8 and mistakes in those initial configs
The rest are the normal mix of small fixes all over the place; sunxi,
omap, imx, mvebu, etc, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=YDHs
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Here's a long-pending fixes pull request for arm-soc (I didn't send
one in the -rc4 cycle).
The larger deltas are from:
- A fixup of error paths in the mvsdio driver
- Header file move for a driver that hadn't been properly converted
to multiplatform on i.MX, which was causing build failures when
included
- Device tree updates for at91 dealing mostly with their new pinctrl
setup merged in 3.8 and mistakes in those initial configs
The rest are the normal mix of small fixes all over the place; sunxi,
omap, imx, mvebu, etc, etc."
* tag 'fixes-for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (40 commits)
mfd: vexpress-sysreg: Don't skip initialization on probe
ARM: vexpress: Enable A7 cores in V2P-CA15_A7's Device Tree
ARM: vexpress: extend the MPIDR range used for pen release check
ARM: at91/dts: correct comment in at91sam9x5.dtsi for mii
ARM: at91/at91_dt_defconfig: add at91sam9n12 SoC to DT defconfig
ARM: at91/at91_dt_defconfig: remove memory specification to cmdline
ARM: at91/dts: add macb mii pinctrl config for kizbox
ARM: at91: rm9200: remake the BGA as default version
ARM: at91: fix gpios on i2c-gpio for RM9200 DT
ARM: at91/at91sam9x5 DTS: add SCK USART pins
ARM: at91/at91sam9x5 DTS: correct wrong PIO BANK values on u(s)arts
ARM: at91/at91-pinctrl documentation: fix typo and add some details
ARM: kirkwood: fix missing #interrupt-cells property
mmc: mvsdio: use devm_ API to simplify/correct error paths.
clk: mvebu/clk-cpu.c: fix memory leakage
ARM: OMAP2+: omap4-panda: add UART2 muxing for WiLink shared transport
ARM: OMAP2+: DT node Timer iteration fix
ARM: OMAP2+: Fix section warning for omap_init_ocp2scp()
ARM: OMAP2+: fix build break for omapdrm
ARM: OMAP2: Fix missing omap2xxx_clkt_vps_late_init function calls
...
* Two cpuidle initialization fixes from Konrad Rzeszutek Wilk.
* cpufreq regression fixes for AMD processors from Borislav Petkov,
Stefan Bader, and Matthew Garrett.
* ACPI cpufreq fix from Thomas Schlichter.
* cpufreq and devfreq fixes related to incorrect usage of operating
performance points (OPP) framework and RCU from Nishanth Menon.
* APEI workaround for incorrect BIOS information from Lans Zhang.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=EEk8
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-for-3.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
- Two cpuidle initialization fixes from Konrad Rzeszutek Wilk.
- cpufreq regression fixes for AMD processors from Borislav Petkov,
Stefan Bader, and Matthew Garrett.
- ACPI cpufreq fix from Thomas Schlichter.
- cpufreq and devfreq fixes related to incorrect usage of operating
performance points (OPP) framework and RCU from Nishanth Menon.
- APEI workaround for incorrect BIOS information from Lans Zhang.
* tag 'pm+acpi-for-3.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: Add module aliases for acpi-cpufreq
ACPI: Check MSR valid bit before using P-state frequencies
PM / devfreq: exynos4_bus: honor RCU lock usage
PM / devfreq: add locking documentation for recommended_opp
cpufreq: cpufreq-cpu0: use RCU locks around usage of OPP
cpufreq: OMAP: use RCU locks around usage of OPP
ACPI, APEI: Fixup incorrect 64-bit access width firmware bug
ACPI / processor: Get power info before updating the C-states
powernow-k8: Add a kconfig dependency on acpi-cpufreq
ACPI / cpuidle: Fix NULL pointer issues when cpuidle is disabled
intel_idle: Don't register CPU notifier if we are not running.
One more oversight in the debugfs code was reported and fixed, plus a
documentation fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=O6T4
-----END PGP SIGNATURE-----
Merge tag 'regmap-fix-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"One more oversight in the debugfs code was reported and fixed, plus a
documentation fix."
* tag 'regmap-fix-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: fix small typo in regmap_bulk_write comment
regmap: debugfs: Fix seeking from the cache
Pull slave-dmaengine fixes from Vinod Koul:
"A few fixes on slave dmanengine. There are trivial fixes in imx-dma,
tegra-dma & ioat driver"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dma: tegra: implement flags parameters for cyclic transfer
dmaengine: imx-dma: Disable use of hw_chain to fix sg_dma transfers.
ioat: Fix DMA memory sync direction correct flag
Usb3.0 device defines function remote wakeup which is only for interface
recipient rather than device recipient. This is different with usb2.0 device's
remote wakeup feature which is defined for device recipient. According usb3.0
spec 9.4.5, the function remote wakeup can be modified by the SetFeature()
requests using the FUNCTION_SUSPEND feature selector. This patch is to use
correct way to disable usb3.0 device's function remote wakeup after suspend
error and resuming.
This should be backported to kernels as old as 3.4, that contain the
commit 623bef9e03 "USB/xhci: Enable remote
wakeup for USB3 devices."
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
When the xHCI driver is not available, actively switch the ports to EHCI
mode since some BIOSes leave them in xHCI mode where they would
otherwise appear dead. This was discovered on a Dell Optiplex 7010,
but it's possible other systems could be affected.
This should be backported to kernels as old as 3.0, that contain the
commit 69e848c209 "Intel xhci: Support
EHCI/xHCI port switching."
Signed-off-by: David Moore <david.moore@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
This patch (as1640) fixes a memory leak in xhci-hcd. The urb_priv
data structure isn't always deallocated in the handle_tx_event()
routine for non-control transfers. The patch adds a kfree() call so
that all paths end up freeing the memory properly.
This patch should be backported to kernels as old as 2.6.36, that
contain the commit 8e51adccd4 "USB: xHCI:
Introduce urb_priv structure"
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-and-tested-by: Martin Mokrejs <mmokrejs@fold.natur.cuni.cz>
CC: <stable@vger.kernel.org>
Fix incorrect bit test that originally showed up in
4ee823b83b "USB/xHCI: Support
device-initiated USB 3.0 resume."
Use '&' instead of '&&'.
This should be backported to kernels as old as 3.4.
Signed-off-by: Nickolai Zeldovich <nickolai@csail.mit.edu>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
To calculate the TD size for a particular TRB in an isoc TD, we need
know the endpoint's max packet size. Isochronous endpoints also encode
the number of additional service opportunities in their wMaxPacketSize
field. The TD size calculation did not mask off those bits before using
the field. This resulted in incorrect TD size information for
isochronous TRBs when an URB frame buffer crossed a 64KB boundary.
For example:
- an isoc endpoint has 2 additional service opportunites and
a max packet size of 1020 bytes
- a frame transfer buffer contains 3060 bytes
- one frame buffer crosses a 64KB boundary, and must be split into
one 1276 byte TRB, and one 1784 byte TRB.
The TD size is is the number of packets that remain to be transferred
for a TD after processing all the max packet sized packets in the
current TRB and all previous TRBs.
For this TD, the number of packets to be transferred is (3060 / 1020),
or 3. The first TRB contains 1276 bytes, which means it contains one
full packet, and a 256 byte remainder. After processing all the max
packet-sized packets in the first TRB, the host will have 2 packets left
to transfer.
The old code would calculate the TD size for the first TRB as:
total packet count = DIV_ROUND_UP (TD length / endpoint wMaxPacketSize)
total packet count - (first TRB length / endpoint wMaxPacketSize)
The math should have been:
total packet count = DIV_ROUND_UP (3060 / 1020) = 3
3 - (1276 / 1020) = 2
Since the old code didn't mask off the additional service interval bits
from the wMaxPacketSize field, the math ended up as
total packet count = DIV_ROUND_UP (3060 / 5116) = 1
1 - (1276 / 5116) = 1
Fix this by masking off the number of additional service opportunities
in the wMaxPacketSize field.
This patch should be backported to stable kernels as old as 3.0, that
contain the commit 4da6e6f247 "xhci 1.0:
Update TD size field format." It may not apply well to kernels older
than 3.2 because of commit 29cc88979a
"USB: use usb_endpoint_maxp() instead of le16_to_cpu()".
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
An isochronous TD is comprised of one isochronous TRB chained to zero or
more normal TRBs. Only the isoc TRB has the TBC and TLBPC fields. The
normal TRBs must set those fields to zeroes. The code was setting the
TBC and TLBPC fields for both isoc and normal TRBs. Fix this.
This should be backported to stable kernels as old as 3.0, that contain
the commit b61d378f2d " xhci 1.0: Set
transfer burst last packet count field."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
From Pawel Moll:
- makes the V2P-CA15_A7 (a.k.a. TC2) work with 3.8 kernels
- improves vexpress-sysreg.c behaviour on arm64 platforms
* 'vexpress/fixes' of git://git.linaro.org/people/pawelmoll/linux:
mfd: vexpress-sysreg: Don't skip initialization on probe
ARM: vexpress: Enable A7 cores in V2P-CA15_A7's Device Tree
ARM: vexpress: extend the MPIDR range used for pen release check
The vexpress-sysreg driver does not have to be initialized
early, when the platform doesn't require this. Unfortunately
in such case it wasn't initialized correctly - master site
lookup and config bridge registration were missing. Fixed now.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
maintainer for some time.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQ/qTBAAoJEFBXWFqHsHzOnNcH/0F8Ul4CJLS/+K80UaJDn7RQ
Di+4zPi/7foByJEUdTC9jDetHREPMeRLX2hzR+2XK+zCtrFPV8VAw4crdxOmLRYb
CxlTuMVA2R68NwvH1+PqTvuiJ6Qxr0HZHzmQdj+x8hWgRkD0RRoD/KQVbkrp8OKh
jJICgd3BXe9GTJszqK13Gj4VOfZvF9YyYDKAiKojfEOV3PyJTdnMBYGGQUD+6FHE
YxfG2xVUh/diFGpWxC5DLQdZ2ow+/7ruPTG+FifVGMcdqYI/KZ/l6cHiHNcFJcQs
6isObI8LeZ87kWJpM/cylqkzyyRGwg12jlFup22CBQCRyWgrgnGNVdoVBuffKJ0=
=Bup/
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.8-3' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo:
This is yet another critical imxfb fixes held off by absence of FB
maintainer for some time.
* tag 'imx-fixes-3.8-3' of git://git.linaro.org/people/shawnguo/linux-2.6:
video: imxfb: Do not crash on reboot
- fix memory leak in mvebu/clk-cpu.c
- use devm_ to correct/simplify error paths in mvsdio
- add missing #interrupt-cells property in kirkwood
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQ/zvKAAoJEAi3KVZQDZAebCIIAKCaI3zYiHku7Q52Auzog0oU
7Gk6/TpZtolZURusjSVo8ZPWoZhJc9SoFAVkVJPcB9j1xTl3K7iNVOj4DVvi66o2
R8dw85nTKryBc6kapiJEpQhJof9dQKzmNSL36TNLaHjPef/hz3gVn/QqOxmyuBro
ZZI0aUm+idgaDFkQCuevcfuStQGaKdOsIr23QEbicTj0rbgy0OIKrQ2KxFGKnr0Z
YYYjUr9M5wk1mSOsssEcE/a97eejHS201JhYvCfxSpWCjbwiaErg0fzns7wZ2hhV
BKGAEs+M67gcaHR/Pi2fy3LNLtwIcVNNgFYF3aCiBEFQ+hqtar6O9zqSmlBk1bI=
=xOtK
-----END PGP SIGNATURE-----
Merge tag 'mvebu_fixes_for_v3.8-rc5' of git://git.infradead.org/users/jcooper/linux into fixes
From Jason Cooper:
mvebu fixes for v3.8-rc5
- fix memory leak in mvebu/clk-cpu.c
- use devm_ to correct/simplify error paths in mvsdio
- add missing #interrupt-cells property in kirkwood
* tag 'mvebu_fixes_for_v3.8-rc5' of git://git.infradead.org/users/jcooper/linux:
ARM: kirkwood: fix missing #interrupt-cells property
mmc: mvsdio: use devm_ API to simplify/correct error paths.
clk: mvebu/clk-cpu.c: fix memory leakage
Here are some more USB fixes for the 3.8-rc4 tree.
Some gadget driver fixes, and finally resolved the ehci-mxc driver build issues
(it's just some code moving around and being deleted).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEAeCEACgkQMUfUDdst+ynRygCeNs8Z0Nt+/quZHKf+/DS4vlRt
vBYAnAxbcPg1zWhMM+8AVt/YFYp83sfP
=5UpK
-----END PGP SIGNATURE-----
Merge tag 'usb-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull more USB fixes from Greg Kroah-Hartman:
"Here are some more USB fixes for the 3.8-rc4 tree.
Some gadget driver fixes, and finally resolved the ehci-mxc driver
build issues (it's just some code moving around and being deleted)."
* tag 'usb-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: EHCI: fix build error in ehci-mxc
USB: EHCI: add a name for the platform-private field
USB: EHCI: fix incorrect configuration test
USB: EHCI: Move definition of EHCI_STATS to ehci.h
USB: UHCI: fix IRQ race during initialization
usb: gadget: FunctionFS: Fix missing braces in parse_opts
usb: dwc3: gadget: fix ep->maxburst for ep0
ARM: i.MX clock: Change the connection-id for fsl-usb2-udc
usb: gadget: fsl_mxc_udc: replace MX35_IO_ADDRESS to ioremap
usb: gadget: fsl-mxc-udc: replace cpu_is_xxx() with platform_device_id
usb: musb: cppi_dma: drop '__init' annotation
Here is a single revert for the ti-st misc driver, fixing problem that was
introduced in 3.7-rc1 that has been bothering people.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEAdxcACgkQMUfUDdst+ynQOgCgmsqcz6DaKFQpcMNKEl/6GWz2
KA4AoNYW3uSDQn1TUbuKmoJSN/SYALK4
=xqHP
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull drivers/misc fix from Greg Kroah-Hartman:
"Here is a single revert for the ti-st misc driver, fixing problem that
was introduced in 3.7-rc1 that has been bothering people."
* tag 'char-misc-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Revert "drivers/misc/ti-st: remove gpio handling"
Pull media fixes from Mauro Carvalho Chehab:
- gspca: add needed delay for I2C traffic for sonixb/sonixj cameras
- gspca: add one missing Kinect USB ID
- usbvideo: some regression fixes
- omap3isp: fix some build issues
- videobuf2: fix video output handling
- exynos s5p/m5mols: a few regression fixes.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] uvcvideo: Set error_idx properly for S_EXT_CTRLS failures
[media] uvcvideo: Cleanup leftovers of partial revert
[media] uvcvideo: Return -EACCES when trying to set a read-only control
[media] omap3isp: Don't include <plat/cpu.h>
[media] s5p-mfc: Fix interrupt error handling routine
[media] s5p-fimc: Fix return value of __fimc_md_create_flite_source_links()
[media] m5mols: Fix typo in get_fmt callback
[media] v4l: vb2: Set data_offset to 0 for single-plane output buffers
[media] [FOR,v3.8] omap3isp: Don't include deleted OMAP plat/ header files
[media] gspca_sonixj: Add a small delay after i2c_w1
[media] gspca_sonixb: Properly wait between i2c writes
[media] gspca_kinect: add Kinect for Windows USB id
This patch (as1643b) fixes a build error in ehci-hcd when compiling for
ARM with allmodconfig:
drivers/usb/host/ehci-hcd.c:1285:0: warning: "PLATFORM_DRIVER" redefined [enabled by default]
drivers/usb/host/ehci-hcd.c:1255:0: note: this is the location of the previous definition
drivers/usb/host/ehci-mxc.c:280:31: warning: 'ehci_mxc_driver' defined but not used [-Wunused-variable]
drivers/usb/host/ehci-hcd.c:1285:0: warning: "PLATFORM_DRIVER" redefined [enabled by default]
drivers/usb/host/ehci-hcd.c:1255:0: note: this is the location of the previous definition
The fix is to convert ehci-mxc over to the new "ehci-hcd is a library"
scheme so that it can coexist peacefully with the ehci-platform
driver. As part of the conversion the ehci_mxc_priv data structure,
which was allocated dynamically, is now placed where it belongs: in
the private area at the end of struct ehci_hcd.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit eccf2979b2.
The reason is that it broke TI WiLink shared transport on Panda.
Also, callback functions should not be added to board files anymore,
so revert to implementing the power functions in the driver itself.
Additionally, changed a variable name ('status' to 'err') so that this
revert compiles properly.
Cc: stable <stable@vger.kernel.org> [3.7]
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a number of bugs in the error paths of this driver. Make
use of devm_ functions to simplify the cleanup on error.
Based on a patch by Russell King.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
the variable cpuclk and clk_name should be properly freed when error happens.
Signed-off-by: Cong Ding <dinggnu@gmail.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Hotplug
PCI: pciehp: Use per-slot workqueues to avoid deadlock
PCI: shpchp: Make shpchp_wq non-ordered
PCI: shpchp: Handle push button event asynchronously
PCI: shpchp: Use per-slot workqueues to avoid deadlock
Power management
PCI: Allow pcie_aspm=force even when FADT indicates it is unsupported
Misc
PCI/AER: pci_get_domain_bus_and_slot() call missing required pci_dev_put()
PCI: remove depends on CONFIG_EXPERIMENTAL
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=lhvi
-----END PGP SIGNATURE-----
Merge tag '3.8-pci-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"The most important is a fix for a pciehp deadlock that occurs when
unplugging a Thunderbolt adapter. We also applied the same fix to
shpchp, removed CONFIG_EXPERIMENTAL dependencies, fixed a
pcie_aspm=force problem, and fixed a refcount leak.
Details:
- Hotplug
PCI: pciehp: Use per-slot workqueues to avoid deadlock
PCI: shpchp: Make shpchp_wq non-ordered
PCI: shpchp: Handle push button event asynchronously
PCI: shpchp: Use per-slot workqueues to avoid deadlock
- Power management
PCI: Allow pcie_aspm=force even when FADT indicates it is unsupported
- Misc
PCI/AER: pci_get_domain_bus_and_slot() call missing required pci_dev_put()
PCI: remove depends on CONFIG_EXPERIMENTAL"
* tag '3.8-pci-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: remove depends on CONFIG_EXPERIMENTAL
PCI: Allow pcie_aspm=force even when FADT indicates it is unsupported
PCI: shpchp: Use per-slot workqueues to avoid deadlock
PCI: shpchp: Handle push button event asynchronously
PCI: shpchp: Make shpchp_wq non-ordered
PCI/AER: pci_get_domain_bus_and_slot() call missing required pci_dev_put()
PCI: pciehp: Use per-slot workqueues to avoid deadlock
The acpi core will call request_module("acpi-cpufreq") on subsystem init,
but this will fail if the module isn't available at that stage of boot.
Add some module aliases to ensure that udev can load the module on Intel
and AMD systems with the appropriate feature bits - I /think/ that this
will also work on VIA systems, but haven't verified that.
References: http://lkml.kernel.org/r/1448223.sdUJnNSRz4@vostro.rjw.lan
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Tested-by: Leonid Isaev <lisaev@umail.iu.edu>
Acked-by: Borislav Petkov <bp@suse.de>
Cc: 3.7+ <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Remove a bad #include from the Samsung driver
- Some Kconfig hazzle for the Samsungs
- Skip gpiolib registration on EXYNOS5440
- Don't free the MVEBU label
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=N1rq
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Here are some GPIO fixes I stacked up in my GPIO tree:
- Remove a bad #include from the Samsung driver
- Some Kconfig hazzle for the Samsungs
- Skip gpiolib registration on EXYNOS5440
- Don't free the MVEBU label"
* tag 'fixes-for-v3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: mvebu: Don't free chip label memory
gpio: samsung: skip gpio lib registration for EXYNOS5440
gpio: samsung: silent build warning for EXYNOS5 SoCs
gpio: samsung: fix pinctrl condition for exynos and exynos5440
gpio: samsung: remove inclusion <mach/regs-clock.h>
- A build fix for recently merged omap DRM changes
- Regression fixes from the common clock framework conversion
for omap4 audio and omap2 reboot
- Regression fix for pandaboard WLAN control UART muxing caused by
u-boot only muxing essential pins nowadays
- Timer iteration fix for CONFIG_OF_DYNAMIC
- A section mismatch fix for ocp2scp init
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=GTdk
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8-rc4/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Minimal omap fixes for the -rc series:
- A build fix for recently merged omap DRM changes
- Regression fixes from the common clock framework conversion
for omap4 audio and omap2 reboot
- Regression fix for pandaboard WLAN control UART muxing caused by
u-boot only muxing essential pins nowadays
- Timer iteration fix for CONFIG_OF_DYNAMIC
- A section mismatch fix for ocp2scp init
* tag 'omap-for-v3.8-rc4/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (306 commits)
ARM: OMAP2+: omap4-panda: add UART2 muxing for WiLink shared transport
ARM: OMAP2+: DT node Timer iteration fix
ARM: OMAP2+: Fix section warning for omap_init_ocp2scp()
ARM: OMAP2+: fix build break for omapdrm
ARM: OMAP2: Fix missing omap2xxx_clkt_vps_late_init function calls
ARM: OMAP4: hwmod_data: Correct IDLEMODE for McPDM
ARM: OMAP4: clock data: Lock ABE DPLL on all revisions
+ Linux 3.8-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
Thought: I wonder if sparse could have caught this, somehow.
2) ahci: support a slightly odd Enmotus variant
3) core: fix a drive detection problem by correcting the logic
by which the DevSlp timing variables are obtained and used.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=7WDW
-----END PGP SIGNATURE-----
Merge tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
Pull libata fixes from Jeff Garzik:
1) ahci: Fix typo that caused erronenous error handling.
Thought: I wonder if sparse could have caught this, somehow.
2) ahci: support a slightly odd Enmotus variant
3) core: fix a drive detection problem by correcting the logic by which
the DevSlp timing variables are obtained and used.
* tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] replace sata_settings with devslp_timing
[libata] ahci: Add support for Enmotus Bobcat device.
[libata] ahci: Fix lack of command retry after a success error handler.
This patch (as1642) adds an ehci->priv field for private use by EHCI
platform drivers. The space was provided some time ago, but it didn't
have a name.
Until now none of the platform drivers has used this private space,
but that's about to change in the next patch of this series.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1641) fixes a minor bug in ehci-hcd left over from when
the Chipidea driver was converted to the "ehci-hcd is a library"
scheme. The test for whether the Chipidea platform driver is active
should be IS_ENABLED(), not defined().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without this, platform drivers e.g. ehci-omap.c will see a
different version of struct ehci_hcd than ehci-hcd.c and
break reference to 'debug_dir' and 'priv' members when
CONFIG_USB_DEBUG is enabled.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1644) fixes a race that occurs during startup in
uhci-hcd. If the IRQ line is shared with other devices, it's possible
for the handler routine to be called before the data structures are
fully initialized.
The problem is fixed by adding a check to the IRQ handler routine. If
the initialization hasn't finished yet, the routine will return
immediately.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Don Zickus <dzickus@redhat.com>
Tested-by: "Huang, Adrian (ISS Linux TW)" <adrian.huang@hp.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
