This patch adds support for IOMMU to s5p-mfc device driver. MFC firmware
is limited and it cannot use the default configuration. If IOMMU is
available, the patch disables the default DMA address space
configuration and creates a new address space of size limited to 256M
and base address set to 0x20000000.
For now the same address space is shared by both 'left' and 'right'
memory channels, because the DMA/IOMMU frameworks do not support
configuring them separately. This is not optimal, but besides limiting
total address space available has no other drawbacks (MFC firmware
supports 256M of address space per each channel).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch removes custom code for initialization and handling of
reserved memory regions in s5p-mfc driver and replaces it with generic
reserved memory regions api.
s5p-mfc driver now handles two reserved memory regions defined by
generic reserved memory bindings. Support for non-dt platform has been
removed, because all supported platforms have been already converted to
device tree.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
All multimedia devices found on Exynos SoCs support only contiguous
buffers, so set DMA max segment size to DMA_BIT_MASK(32) to let memory
allocator to correctly create contiguous memory mappings.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Add a helper function for device drivers to set DMA's max_seg_size.
Setting it to largest possible value lets DMA-mapping API always create
contiguous mappings in DMA address space. This is essential for all
devices, which use dma-contig videobuf2 memory allocator and shared
buffers.
Till now, the only case when vb2-dma-contig really 'worked' was a case
where userspace provided USERPTR buffer, which was in fact mmaped
contiguous buffer from the other v4l2/drm device. Also DMABUF made of
contiguous buffer worked only when its exporter did not split it into
several chunks in the scatter-list. Any other buffer failed, regardless
of the arch/platform used and the presence of the IOMMU of the device bus.
This patch provides interface to fix this issue.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The s5p_mfc_probe() function registers the video devices before all the
resources needed by s5p_mfc_open() are correctly initalized.
So if s5p_mfc_open() function is called before s5p_mfc_probe() finishes
(since the video dev is already registered), a NULL pointer dereference
will happen due s5p_mfc_open() accessing uninitialized vars such as the
struct s5p_mfc_dev .watchdog_timer and .mfc_ops fields.
An example is following BUG caused by add_timer() getting a NULL pointer:
[ 45.765374] kernel BUG at kernel/time/timer.c:790!
[ 45.765381] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
...
[ 45.766149] [<c016fdf4>] (mod_timer) from [<bf181d18>] (s5p_mfc_open+0x274/0x4d4 [s5p_mfc])
[ 45.766416] [<bf181d18>] (s5p_mfc_open [s5p_mfc]) from [<bf0214a0>] (v4l2_open+0x9c/0x100 [videodev])
[ 45.766547] [<bf0214a0>] (v4l2_open [videodev]) from [<c01e355c>] (chrdev_open+0x9c/0x178)
[ 45.766575] [<c01e355c>] (chrdev_open) from [<c01dceb4>] (do_dentry_open+0x1e0/0x300)
[ 45.766595] [<c01dceb4>] (do_dentry_open) from [<c01ec2f0>] (path_openat+0x800/0x10d4)
[ 45.766610] [<c01ec2f0>] (path_openat) from [<c01ed8b8>] (do_filp_open+0x5c/0xc0)
[ 45.766624] [<c01ed8b8>] (do_filp_open) from [<c01de218>] (do_sys_open+0x10c/0x1bc)
[ 45.766642] [<c01de218>] (do_sys_open) from [<c01078c0>] (ret_fast_syscall+0x0/0x3c)
[ 45.766655] Code: eaffffe3 e3a00001 e28dd008 e8bd81f0 (e7f001f2)
Fix it by registering the video devs as the last step in s5p_mfc_probe().
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
When s5p_mfc_remove() calls put_device() for the reserved memory region
devs, the driver core warns that the dev doesn't have a release callback:
WARNING: CPU: 0 PID: 591 at drivers/base/core.c:251 device_release+0x8c/0x90
Device 's5p-mfc-l' does not have a release() function, it is broken and must be fixed.
Also, the declared DMA memory using dma_declare_coherent_memory() isn't
relased so add a dev .release that calls dma_release_declared_memory().
Cc: <stable@vger.kernel.org>
Fixes: 6e83e6e25e ("[media] s5p-mfc: Fix kernel warning on memory init")
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The devices don't have a name set, so makes dev_name() returns NULL which
makes harder to identify the devices that are causing issues, for example:
WARNING: CPU: 2 PID: 616 at drivers/base/core.c:251 device_release+0x8c/0x90
Device '(null)' does not have a release() function, it is broken and must be fixed.
And after setting the device name:
WARNING: CPU: 0 PID: 591 at drivers/base/core.c:251 device_release+0x8c/0x90
Device 's5p-mfc-l' does not have a release() function, it is broken and must be fixed.
Cc: <stable@vger.kernel.org>
Fixes: 6e83e6e25e ("[media] s5p-mfc: Fix kernel warning on memory init")
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Pull string hash improvements from George Spelvin:
"This series does several related things:
- Makes the dcache hash (fs/namei.c) useful for general kernel use.
(Thanks to Bruce for noticing the zero-length corner case)
- Converts the string hashes in <linux/sunrpc/svcauth.h> to use the
above.
- Avoids 64-bit multiplies in hash_64() on 32-bit platforms. Two
32-bit multiplies will do well enough.
- Rids the world of the bad hash multipliers in hash_32.
This finishes the job started in commit 689de1d6ca ("Minimal
fix-up of bad hashing behavior of hash_64()")
The vast majority of Linux architectures have hardware support for
32x32-bit multiply and so derive no benefit from "simplified"
multipliers.
The few processors that do not (68000, h8/300 and some models of
Microblaze) have arch-specific implementations added. Those
patches are last in the series.
- Overhauls the dcache hash mixing.
The patch in commit 0fed3ac866 ("namei: Improve hash mixing if
CONFIG_DCACHE_WORD_ACCESS") was an off-the-cuff suggestion.
Replaced with a much more careful design that's simultaneously
faster and better. (My own invention, as there was noting suitable
in the literature I could find. Comments welcome!)
- Modify the hash_name() loop to skip the initial HASH_MIX(). This
would let us salt the hash if we ever wanted to.
- Sort out partial_name_hash().
The hash function is declared as using a long state, even though
it's truncated to 32 bits at the end and the extra internal state
contributes nothing to the result. And some callers do odd things:
- fs/hfs/string.c only allocates 32 bits of state
- fs/hfsplus/unicode.c uses it to hash 16-bit unicode symbols not bytes
- Modify bytemask_from_count to handle inputs of 1..sizeof(long)
rather than 0..sizeof(long)-1. This would simplify users other
than full_name_hash"
Special thanks to Bruce Fields for testing and finding bugs in v1. (I
learned some humbling lessons about "obviously correct" code.)
On the arch-specific front, the m68k assembly has been tested in a
standalone test harness, I've been in contact with the Microblaze
maintainers who mostly don't care, as the hardware multiplier is never
omitted in real-world applications, and I haven't heard anything from
the H8/300 world"
* 'hash' of git://ftp.sciencehorizons.net/linux:
h8300: Add <asm/hash.h>
microblaze: Add <asm/hash.h>
m68k: Add <asm/hash.h>
<linux/hash.h>: Add support for architecture-specific functions
fs/namei.c: Improve dcache hash function
Eliminate bad hash multipliers from hash_32() and hash_64()
Change hash_64() return value to 32 bits
<linux/sunrpc/svcauth.h>: Define hash_str() in terms of hashlen_string()
fs/namei.c: Add hashlen_string() function
Pull out string hash to <linux/stringhash.h>
The "simplified" prime multipliers made very bad hash functions, so get rid
of them. This completes the work of 689de1d6ca.
To avoid the inefficiency which was the motivation for the "simplified"
multipliers, hash_64() on 32-bit systems is changed to use a different
algorithm. It makes two calls to hash_32() instead.
drivers/media/usb/dvb-usb-v2/af9015.c uses the old GOLDEN_RATIO_PRIME_32
for some horrible reason, so it inherits a copy of the old definition.
Signed-off-by: George Spelvin <linux@sciencehorizons.net>
Cc: Antti Palosaari <crope@iki.fi>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Most users of IS_ERR_VALUE() in the kernel are wrong, as they
pass an 'int' into a function that takes an 'unsigned long'
argument. This happens to work because the type is sign-extended
on 64-bit architectures before it gets converted into an
unsigned type.
However, anything that passes an 'unsigned short' or 'unsigned int'
argument into IS_ERR_VALUE() is guaranteed to be broken, as are
8-bit integers and types that are wider than 'unsigned long'.
Andrzej Hajda has already fixed a lot of the worst abusers that
were causing actual bugs, but it would be nice to prevent any
users that are not passing 'unsigned long' arguments.
This patch changes all users of IS_ERR_VALUE() that I could find
on 32-bit ARM randconfig builds and x86 allmodconfig. For the
moment, this doesn't change the definition of IS_ERR_VALUE()
because there are probably still architecture specific users
elsewhere.
Almost all the warnings I got are for files that are better off
using 'if (err)' or 'if (err < 0)'.
The only legitimate user I could find that we get a warning for
is the (32-bit only) freescale fman driver, so I did not remove
the IS_ERR_VALUE() there but changed the type to 'unsigned long'.
For 9pfs, I just worked around one user whose calling conventions
are so obscure that I did not dare change the behavior.
I was using this definition for testing:
#define IS_ERR_VALUE(x) ((unsigned long*)NULL == (typeof (x)*)NULL && \
unlikely((unsigned long long)(x) >= (unsigned long long)(typeof(x))-MAX_ERRNO))
which ends up making all 16-bit or wider types work correctly with
the most plausible interpretation of what IS_ERR_VALUE() was supposed
to return according to its users, but also causes a compile-time
warning for any users that do not pass an 'unsigned long' argument.
I suggested this approach earlier this year, but back then we ended
up deciding to just fix the users that are obviously broken. After
the initial warning that caused me to get involved in the discussion
(fs/gfs2/dir.c) showed up again in the mainline kernel, Linus
asked me to send the whole thing again.
[ Updated the 9p parts as per Al Viro - Linus ]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lkml.org/lkml/2016/1/7/363
Link: https://lkml.org/lkml/2016/5/27/486
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> # For nvmem part
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge updates from Andrew Morton:
- fsnotify fix
- poll() timeout fix
- a few scripts/ tweaks
- debugobjects updates
- the (small) ocfs2 queue
- Minor fixes to kernel/padata.c
- Maybe half of the MM queue
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (117 commits)
mm, page_alloc: restore the original nodemask if the fast path allocation failed
mm, page_alloc: uninline the bad page part of check_new_page()
mm, page_alloc: don't duplicate code in free_pcp_prepare
mm, page_alloc: defer debugging checks of pages allocated from the PCP
mm, page_alloc: defer debugging checks of freed pages until a PCP drain
cpuset: use static key better and convert to new API
mm, page_alloc: inline pageblock lookup in page free fast paths
mm, page_alloc: remove unnecessary variable from free_pcppages_bulk
mm, page_alloc: pull out side effects from free_pages_check
mm, page_alloc: un-inline the bad part of free_pages_check
mm, page_alloc: check multiple page fields with a single branch
mm, page_alloc: remove field from alloc_context
mm, page_alloc: avoid looking up the first zone in a zonelist twice
mm, page_alloc: shortcut watermark checks for order-0 pages
mm, page_alloc: reduce cost of fair zone allocation policy retry
mm, page_alloc: shorten the page allocator fast path
mm, page_alloc: check once if a zone has isolated pageblocks
mm, page_alloc: move __GFP_HARDWALL modifications out of the fastpath
mm, page_alloc: simplify last cpupid reset
mm, page_alloc: remove unnecessary initialisation from __alloc_pages_nodemask()
...
A few instances of "fimware" instead of "firmware" were found. Fix
these and add it to the spelling.txt file.
Signed-off-by: Kees Cook <keescook@chromium.org>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull i2c updates from Wolfram Sang:
- Peter Rosin did some major rework on the locking of i2c muxes by
seperating parent-locked muxes and mux-locked muxes.
This avoids deadlocks/workarounds when the mux itself needs i2c
commands for muxing. And as a side-effect, other workarounds in the
media layer could be eliminated. Also, Peter stepped up as the i2c
mux maintainer and will keep an eye on these changes.
- major updates to the octeon driver
- add a helper to the core to generate the address+rw_bit octal and
make drivers use it
- quite a bunch of driver updates
* 'i2c/for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (84 commits)
i2c: rcar: add DMA support
i2c: st: Implement bus clear
i2c: only check scl functions when using generic recovery
i2c: algo-bit: declare i2c_bit_quirk_no_clk_stretch as static
i2c: tegra: disable clock before returning error
[media] rtl2832: regmap is aware of lockdep, drop local locking hack
[media] rtl2832_sdr: get rid of empty regmap wrappers
[media] rtl2832: change the i2c gate to be mux-locked
[media] si2168: change the i2c gate to be mux-locked
iio: imu: inv_mpu6050: change the i2c gate to be mux-locked
i2c: mux: document i2c muxes and elaborate on parent-/mux-locked muxes
i2c: mux: relax locking of the top i2c adapter during mux-locked muxing
i2c: muxes always lock the parent adapter
i2c: allow adapter drivers to override the adapter locking
i2c: uniphier: add "\n" at the end of error log
i2c: mv64xxx: remove CONFIG_HAVE_CLK conditionals
i2c: mv64xxx: use clk_{prepare_enable,disable_unprepare}
i2c: mv64xxx: handle probe deferral for the clock
i2c: mv64xxx: enable the driver on ARCH_MVEBU
i2c: octeon: Add workaround for broken irqs on CN3860
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=PEbo
-----END PGP SIGNATURE-----
Merge tag 'media/v4.6-6' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fix from Mauro Carvalho Chehab:
"A revert fixing a breakage that caused an OOPS on all VB2-based DVB
drivers.
We already have a proper fix, but it sounds safer to keep it being
tested for a while and not hurry, to avoid the risk of another
regression, specially since this is meant to be c/c to stable. So,
for now, let's just revert the broken patch"
* tag 'media/v4.6-6' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
Revert "[media] videobuf2-v4l2: Verify planes array in buffer dequeueing"
When building the exynos-gsc driver with CONFIG_OF disabled, we get
a warning about an out-of-bounds access:
drivers/media/platform/exynos-gsc/gsc-core.c: In function 'gsc_probe':
drivers/media/platform/exynos-gsc/gsc-core.c:1078:34: error: array subscript is above array bounds [-Werror=array-bounds]
This is harmless because the driver will never be used without CONFIG_OF,
but it's better to avoid the warning anyway. Checking the return value
of of_alias_get_id() for an error condition is probably a good idea
anyway, and it makes sure the compiler can verify that we don't get
into that situation.
Fixes: 26a7ed9c18 ("[media] exynos-gsc: remove an always false condition")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The tvp5150_write() function can fail so don't return 0 unconditionally
in tvp5150_s_register() but propagate what's returned by tvp5150_write().
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The tvp5150_write() function calls i2c_smbus_write_byte_data() that
can fail but does not propagate the error to the caller. Instead it
just prints a debug, so callers can't know if the operation failed.
So change the function to return the error code to the caller so it
knows that the write failed and also print an error instead of just
printing a debug information.
While being there remove the inline keyword from tvp5150_write() to
make it consistent with tvp5150_read() and also because it's called
in a lot of places, so making inline is in fact counter productive
since it makes the kernel image size to be much bigger (~16 KiB).
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Hauppauge WinTV-dualHD is a USB 2.0 dual DVB-T/T2/C tuner with
following components:
USB bridge: Empia EM28274 (chip id is the same as EM28174)
Demodulator: 2x Silicon Labs Si2168-B40
Tuner: 2x Silicon Labs Si2157-A30
This patch adds support only for the first tuner.
The demodulator needs firmware, available for example here:
http://palosaari.fi/linux/v4l-dvb/firmware/Si2168/Si2168-B40/4.0.11/
The demodulators sit on the same I2C bus and their addresses
are 0x64 and 0x67. The tuners are behind the demodulators and
their addresses are 0x60 and 0x63.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
au0828_v4l2_device_register() unlocks au0828_dev->lock and frees au0828
dev in error legs before return. au0828_usb_probe() does the same when
au0828_v4l2_device_register() returns error.
Fix au0828_v4l2_device_register() to not to unlock and free in its error
legs.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
c8sectpfe driver relied on CONFIG_FW_LOADER_USER_HELPER_FALLBACK option
for loading its xp70 firmware. A previous commit removed this Kconfig
option, as it is apparently harmful, but did not update the driver
code which relied on it.
This patch reworks the firmware loading into the start_feed callback.
At this point we can be sure the rootfs is present, thereby removing
the depedency on CONFIG_FW_LOADER_USER_HELPER_FALLBACK.
Fixes: 79f5b6ae96 ('[media] c8sectpfe: Remove select on CONFIG_FW_LOADER_USER_HELPER_FALLBACK')
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
During the review process, a regression was intoduced in the
circular buffer write pointer management. This means that wp
doesn't get managed properly once the buffer becomes full.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXL7HfAAoJEHm+PkMAQRiGYe8IAJBGaPUq38EJh2YOV+AQf9v6
t/alhwB3DUE1E0zjLy7I7JJ+xDXtKjZh9fS6OFuIS8Q3RIrBteIJ/oH8TPpt7yZ/
SnP6rYPvYD6CImTyrh7+ORL/udEwJX8+YqFYAgUAq167gvpDjYj8r26VzdIaIN4/
oBbL8NrQNWfODieywYyhUoitVhwMz09zmBfLtGVks4vd2jUJk2Fdd9cOtGV5tRfk
DPndPgyQtbr8W0mKovV8sT9WkQeV5TsUr4MLgf7hjnAGYQ8+0KamkzzVVLBeBiiw
uazyrOCFkddZp+N7KbmbOmazV/yULRuLGgDjVKazoCsOaKOvoGCzrCk7daOPy6Q=
=CegX
-----END PGP SIGNATURE-----
Merge tag 'v4.6-rc7' into patchwork
Linux 4.6-rc7
* tag 'v4.6-rc7': (185 commits)
Linux 4.6-rc7
parisc: fix a bug when syscall number of tracee is __NR_Linux_syscalls
x86/tsc: Read all ratio bits from MSR_PLATFORM_INFO
mailmap: add John Paul Adrian Glaubitz
byteswap: try to avoid __builtin_constant_p gcc bug
lib/stackdepot: avoid to return 0 handle
mm: fix kcompactd hang during memory offlining
modpost: fix module autoloading for OF devices with generic compatible property
proc: prevent accessing /proc/<PID>/environ until it's ready
mm/zswap: provide unique zpool name
mm: thp: kvm: fix memory corruption in KVM with THP enabled
MAINTAINERS: fix Rajendra Nayak's address
mm, cma: prevent nr_isolated_* counters from going negative
mm: update min_free_kbytes from khugepaged after core initialization
huge pagecache: mmap_sem is unlocked when truncation splits pmd
rapidio/mport_cdev: fix uapi type definitions
mm: memcontrol: let v2 cgroups follow changes in system swappiness
mm: thp: correct split_huge_pages file permission
maintainers: update rmk's email address(es)
writeback: Fix performance regression in wb_over_bg_thresh()
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0D5s
-----END PGP SIGNATURE-----
Merge tag 'media/v4.6-5' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- deadlock fixes on driver probe at exynos4-is and s43-camif drivers
- a build breakage if media controller is enabled and USB or PCI is
built as module.
* tag 'media/v4.6-5' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] media-device: fix builds when USB or PCI is compiled as module
[media] media: s3c-camif: fix deadlock on driver probe()
[media] media: exynos4-is: fix deadlock on driver probe
Only MEDIA_IOC_ENUM_LINKS32 require an special logic when
userspace is 32 bits and Kernel is 64 bits.
For the rest, media_device_ioctl() will do the right thing,
and will return -ENOIOCTLCMD if the ioctl is unknown.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The extraneous assignment on bt is redundant and can be removed.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
A couple of data structures in the dibusb-common file are only
accessed when CONFIG_DVB_DIB3000MC is enabled, otherwise we
get a harmless gcc warning:
usb/dvb-usb/dibusb-common.c:223:34: error: 'dib3000p_panasonic_agc_config' defined but not used
usb/dvb-usb/dibusb-common.c:211:32: error: 'stk3000p_dib3000p_config' defined but not used
This moves the existing #ifdef a few lines up to correctly cover
all the conditional data structures, which gets rid of the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
of_graph_get_next_endpoint(node, ep) decrements refcount on
ep. When next==NULL we break and refcount on ep is decremented
again.
Signed-off-by: Franck Jullien <franck.jullien@odyssee-systemes.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Callbacks invoked from put_device() may free the struct media_devnode
pointer, so any cleanup needs to be done before put_device().
Signed-off-by: Max Kellermann <max@duempel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
After media_devnode_unregister(), the struct media_device may be freed
already, and dereferencing it may crash.
Signed-off-by: Max Kellermann <max@duempel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
CONFIG_DEBUG_KOBJECT_RELEASE found this bug.
Signed-off-by: Max Kellermann <max@duempel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of always return -ENOMEM, return the real error that should
come from media_create_pad_link().
Signed-off-by: Max Kellermann <max@duempel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add USB ID of SMK RXX6000 series IR receiver. Often branded as
Lenovo receiver.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
New USB ID for Adaptec eHome receiver in some HP laptops.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Access to dev->initialized is atomic and dev->initialized isn't
accessed in any other code protected by this mutex.
Therefore we don't need to get the mutex here.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The ds3000 driver returned 1 as an error code in many places.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove the if..else statement from smipcie-ir.c and add the remote
controller map as a configuration parameter for the card.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Modify the printout for MAC address to be more vendor agnostic.
Print also the port number.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for TechnoTrend TT-budget S2-4200 Twin DVB-S2 tuner. The
device seems to be rather similar to DVBSky S952 V3. This is a PCIe
card with 2 tuners. SMI PCIe bridge is used and the card has two
Montage M88RS6000 demod/tuners.
The M88RS6000 demod/tuner package needs firmware. You can download
one here:
http://palosaari.fi/linux/v4l-dvb/firmware/M88RS6000/
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Max Nibble <nibble.max@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Passing overlapping source and destination to snprintf is
fragile. Replace with a single (mostly) equivalent call. If one wants
to preserve the space preceding udev->product whether or not there was
a manufacturer, just remove udev->manufacturer from the && expression.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Appending to a string by doing snprintf(buf, bufsize, "%s...", buf,
...) is not guaranteed to work.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
PX-BCUD has the following components:
USB interface: Empia EM28178
Demodulator: Toshiba TC90532 (works by code for TC90522)
Tuner: Next version of Sharp QM1D1C0042
em28xx_dvb_init(): add init code for PLEX PX-BCUD with calling
px_bcud_init() that does things like pin configuration.
qm1d1c0042_init(): support the next version of QM1D1C0042, change to
choose an appropriate array of initial registers by reading chip id.
[mchehab@osg.samsung.com: fold a fixup patch and fix checkpatch.pl
errors/warnings, where applicable]
Signed-off-by: Satoshi Nagahama <sattnag@aim.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Another version of Elgato EyeTV Sat USB DVB-S2 adapter needs just
a USB ID addition.
Signed-off-by: Christian Knippel <namerp@gmail.com>
Reported-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It's been reported that CJC7113 devices are returning
all 1s when reading register 0:
"1111111111111111" found @ 0x4a (stk1160)
This new device is apparently compatible with SA7113, so let's
add a quirk to allow its autodetection. Given there isn't
any known differences with SAA7113, this commit does not
introduces a new saa711x_model value.
Reported-by: Philippe Desrochers <desrochers.philippe@gmail.com>
Signed-off-by: Kevin Fitch <kfitch42@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
- Add a check for the case that both the cropcap and g_selection ops
are NULL. This shouldn't happen, but I feel happier if the code
guards against this.
- If g_selection exists, then ignore ENOTTY and ENOIOCTLCMD error
codes from cropcap. Just assume square pixelaspect ratio in that
case. This situation can happen if the bridge driver's cropcap op
calls the corresponding subdev's op. So the cropcap ioctl is set,
but it might return ENOIOCTLCMD anyway. In the past this would
just return an error which is wrong.
- Call cropcap first and let g_selection overwrite the bounds and
defrect. This safeguards against subdev cropcap implementations
that set those rectangles as well. What g_selection returns has
priority over what such cropcap implementations return.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Some sensors (like the one in Nokia N900) provide metadata in the first
couple of lines. Make that information information available to the
pipeline.
Use u16 instead, this is a 16-bit value.
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The devm_gpiod_get() function returns either a valid pointer to
struct gpio_desc or ERR_PTR() error value, check for NULL is bogus.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Right now, dw2102 assumes that the USB IDs will be either at
an external header or defined internally. That doesn't sound
right.
So, let's move the definitions to just one place.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add entries for all supported chip variants into the of_match list, so that
the matching driver_info can be selected when using dt.
Signed-off-by: Julian Scheel <julian@jusst.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Detect if firmware is running run-time and download / start it only
when needed. Detection is done by reading IF frequency value.
Garbage value is returned by firmware when it is not running,
otherwise correct value is returned.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Using div_u64() instead of do_div() makes the code slightly more
readable by humans.
[mchehab@osg.samsung.org: originally, this patch was proposed as a bug
fix for a gcc bug. This was solved already, but it is still better to
use div_u64, instead of do_div, so I'm applying it, removing the
comments about the gcc bug]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Just checking ifdef CONFIG_USB is not enough, if the USB is compiled
as module. The same applies to PCI.
Tested with the following .config alternatives:
CONFIG_USB=m
CONFIG_MEDIA_CONTROLLER=y
CONFIG_MEDIA_SUPPORT=m
CONFIG_VIDEO_AU0828=m
CONFIG_USB=m
CONFIG_MEDIA_CONTROLLER=y
CONFIG_MEDIA_SUPPORT=y
CONFIG_VIDEO_AU0828=m
CONFIG_USB=y
CONFIG_MEDIA_CONTROLLER=y
CONFIG_MEDIA_SUPPORT=y
CONFIG_VIDEO_AU0828=m
CONFIG_USB=y
CONFIG_MEDIA_CONTROLLER=y
CONFIG_MEDIA_SUPPORT=y
CONFIG_VIDEO_AU0828=y
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Tested-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The root i2c adapter lock is then no longer held by the i2c mux during
accesses behind the i2c gate, and such accesses need to take that lock
just like any other ordinary i2c accesses do.
So, declare the i2c gate mux-locked, and zap the regmap overrides
that makes the i2c accesses unlocked and use plain old regmap
accesses. This also removes the need for the regmap wrappers used by
rtl2832_sdr, so deconvolute the code further and provide the regmap
handle directly instead of the wrapper functions.
Tested-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The root i2c adapter lock is then no longer held by the i2c mux during
accesses behind the i2c gate, and such accesses need to take that lock
just like any other ordinary i2c accesses do.
So, declare the i2c gate mux-locked, and zap the code that makes the
i2c accesses unlocked. But add a mutex so that firmware commands are
still serialized.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit 0c426c472b ("[media] media: Always
keep a graph walk large enough around") changed
media_device_register_entity() function to take mdev->graph_mutex. This
causes deadlock in driver probe, which calls (indirectly) this function
with ->graph_mutex taken. This patch removes taking ->graph_mutex in
driver probe to avoid deadlock. Other drivers don't take ->graph_mutex
for entity registration, so this change should be safe.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit 0c426c472b ("[media] media: Always
keep a graph walk large enough around") changed
media_device_register_entity() function to take mdev->graph_mutex. This
causes deadlock in driver probe, which calls (indirectly) this function
with ->graph_mutex taken. This patch removes taking ->graph_mutex in
driver probe to avoid deadlock. Other drivers don't take ->graph_mutex
for entity registration, so this change should be safe.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXJoi6AAoJEHm+PkMAQRiGYKIIAIcocIV48DpGAHXFuSZbzw5D
rp9EbE5TormtddPz1J1zcqu9tl5H8tfxS+LvHqRaDXqQkbb0BWKttmEpKTm9mrH8
kfGNW8uwrEgTMMsar54BypAMMhHz4ITsj3VQX5QLSC5j6wixMcOmQ+IqH0Bwt3wr
Y5JXDtZRysI1GoMkSU7/qsQBjC7aaBa5VzVUiGvhV8DdvPVFQf73P89G1vzMKqb5
HRWbH4ieu6/mclLvW9N2QKGMHQntlB+9m2kG9nVWWbBSDxpAotwqQZFh3D52MBUy
6DH/PNgkVyDhX4vfjua0NrmXdwTfKxLWGxe4dZ8Z+JZP5c6pqWlClIPBCkjHj50=
=KLSM
-----END PGP SIGNATURE-----
Merge tag 'v4.6-rc6' into patchwork
Linux 4.6-rc6
* tag 'v4.6-rc6': (762 commits)
Linux 4.6-rc6
EDAC: i7core, sb_edac: Don't return NOTIFY_BAD from mce_decoder callback
Documentation/sysctl/vm.txt: update numa_zonelist_order description
lib/stackdepot.c: allow the stack trace hash to be zero
rapidio: fix potential NULL pointer dereference
mm/memory-failure: fix race with compound page split/merge
ocfs2/dlm: return zero if deref_done message is successfully handled
Ananth has moved
kcov: don't profile branches in kcov
kcov: don't trace the code coverage code
mm: wake kcompactd before kswapd's short sleep
.mailmap: add Frank Rowand
mm/hwpoison: fix wrong num_poisoned_pages accounting
mm: call swap_slot_free_notify() with page lock held
mm: vmscan: reclaim highmem zone if buffer_heads is over limit
numa: fix /proc/<pid>/numa_maps for THP
mm/huge_memory: replace VM_NO_THP VM_BUG_ON with actual VMA check
mailmap: fix Krzysztof Kozlowski's misspelled name
thp: keep huge zero page pinned until tlb flush
mm: exclude HugeTLB pages from THP page_mapped() logic
...
According to the V4L2 API, the VIDIOC_STREAMON ioctl should return EPIPE
if there is a format mismatch in the pipeline configuration.
As the .vidioc_streamon in the v4l2_ioctl_ops usually forwards the error
caused by the v4l2_subdev_link_validate_default (if it is in use), it
should return -EPIPE when it detect the mismatch.
When an entity is connected to a non enabled link,
media_entity_pipeline_start should return -ENOLINK, as the link does not
exist.
Signed-off-by: Helen Mae Koike Fornazier <helen.koike@collabora.co.uk>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=REYX
-----END PGP SIGNATURE-----
Merge tag 'media/v4.6-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"Some regression fixes:
- videobuf2 core: avoid the risk of going past buffer on multi-planes
and fix rw mode
- fix support for 4K formats at V4L2 core
- fix a trouble at davinci_fpe, caused by a bad patch
- usbvision: revert a patch with a partial fixup. The fixup patch
was merged already, and this one has some issues"
* tag 'media/v4.6-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] vb2-memops: Fix over allocation of frame vectors
[media] media: vb2: Fix regression on poll() for RW mode
[media] v4l2-dv-timings.h: fix polarity for 4k formats
[media] davinci_vpfe: Revert "staging: media: davinci_vpfe: remove,unnecessary ret variable"
[media] usbvision: revert commit 588afcc1
[media] videobuf2-v4l2: Verify planes array in buffer dequeueing
[media] videobuf2-core: Check user space planes array in dqbuf
Fix those two warnings:
drivers/media/pci/tw686x/tw686x-video.c:69 tw686x_fields_map() error: buffer overflow 'std_525_60' 31 <= 31
drivers/media/pci/tw686x/tw686x-video.c:73 tw686x_fields_map() error: buffer overflow 'std_625_50' 26 <= 26
I had those changes at the last version of my patch, but I ended
by merging the previous version by mistake.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
On page unaligned frames, create_framevec forces get_vaddr_frames to
allocate an extra page at the end of the buffer. Under some
circumstances, this leads to -EINVAL on VIDIOC_QBUF.
E.g:
We have vm_a that vm_area that goes from 0x1000 to 0x3000. And a
frame that goes from 0x1800 to 0x2800, i.e. 2 pages.
frame_vector_create will be called with the following params:
get_vaddr_frames(0x1800, 2, write, 1, vec);
get_vaddr will allocate the first page after checking that the memory
0x1800-0x27ff is valid, but it will not allocate the second page because
the range 0x2800-0x37ff is out of the vm_a range. This results in
create_framevec returning -EFAULT
Error Trace:
[ 9083.793015] video0: VIDIOC_QBUF: 00:00:00.00000000 index=1,
type=vid-cap, flags=0x00002002, field=any, sequence=0,
memory=userptr, bytesused=0, offset/userptr=0x7ff2b023ca80, length=5765760
[ 9083.793028] timecode=00:00:00 type=0, flags=0x00000000,
frames=0, userbits=0x00000000
[ 9083.793117] video0: VIDIOC_QBUF: error -22: 00:00:00.00000000
index=2, type=vid-cap, flags=0x00000000, field=any, sequence=0,
memory=userptr, bytesused=0, offset/userptr=0x7ff2b07bc500, length=5765760
Also use true instead of 1 since that argument is a bool in the
get_vaddr_frames() prototype.
Fixes: 21fb0cb7ec ("[media] vb2: Provide helpers for mapping virtual addresses")
Reported-by: Albert Antony <albert@newtec.dk>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
[hans.verkuil@cisco.com: merged the 'bool' change into this patch]
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: <stable@vger.kernel.org> # for v4.3 and up
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When using a device is read/write mode, vb2 does not handle properly the
first select/poll operation.
The reason for this, is that when this code has been refactored, some of
the operations have changed their order, and now fileio emulator is not
started.
The reintroduced check to the core is enabled by a quirk flag, that
avoids this check by other subsystems like DVB.
Fixes: 49d8ab9fea ("media] media: videobuf2: Separate vb2_poll()")
Reported-by: Dimitrios Katsaros <patcherwork@gmail.com>
Cc: Junghak Sung <jh1009.sung@samsung.com>
Cc: <stable@vger.kernel.org> # for v4.5 and up
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Depending on the compiler version, currently it produces the
following warnings:
tw686x-video.c: In function 'tw686x_video_init':
tw686x-video.c:65:543: warning: array subscript is above array bounds [-Warray-bounds]
This is actually bogus with the current code, as it currently
hardcodes the framerate to 30 frames/sec, however a potential
use after the array size could happen when the driver adds support
for setting the framerate. So, fix it.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Marking these controls as private seemed a good idea at one time,
but in practice it makes no sense. So drop this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The control in question is not a private control, so drop that
comment. Copy-and-paste left-over.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The s_std ioctl was broken in this driver, partially due to the
changes to the adv7180 driver (this affected the handling of
V4L2_STD_ALL) and partially because the new standard was never
stored in vip->std.
The handling of V4L2_STD_ALL has been rewritten to just call querystd
and the new standard is now stored correctly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The adv7180 attempts to autodetect the standard. Unfortunately this
is seriously broken.
This patch removes the autodetect completely. Only the querystd op
will detect the standard. Since the design of the adv7180 requires
that you switch to a special autodetect mode you cannot call querystd
when you are streaming.
So the s_stream op has been added so we know whether we are streaming
or not, and if we are, then querystd returns EBUSY.
After testing this with a signal generator is became obvious that
a sleep is needed between changing the standard to autodetect and
reading the status. So the autodetect can never have worked well.
The s_std call now just sets the new standard without any querying.
If the driver supports the interrupt, then when it detects a standard
change it will signal that by sending the V4L2_EVENT_SOURCE_CHANGE
event.
With these changes this driver now behaves like all other video
receivers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We print an uninitialized "actlen" variable on the error path.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When determining if the standard is 50 or 60 Hz it is standard
practice to test for 60 Hz instead of 50 Hz.
This doesn't matter normally, except if the user specifies both
60 and 50 Hz standards.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select op to be in terms of the i2c mux core instead
of the child adapter.
Tested-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select/deselect ops to be in terms of the i2c mux core
instead of the child adapter.
Tested-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select/deselect ops to be in terms of the i2c mux core
instead of the child adapter.
Tested-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select op to be in terms of the i2c mux core instead
of the child adapter.
Tested-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select op to be in terms of the i2c mux core instead
of the child adapter.
Tested-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The test pattern generator will be used by other drivers as the virtual
media controller (vimc)
Signed-off-by: Helen Mae Koike Fornazier <helen.koike@collabora.co.uk>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The v4l2_rect helper functions have been moved to
include/media/v4l2-rect.h. Use this new header, dropping the functions
from vivid.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of rolling our own define, just use the new mask defines.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The v4l2_device_call_* defines filter subdevs based on the grp_id value.
But some drivers use a bitmask, so instead of filtering by grp_id == value,
you want to filter by grp_id & value.
Make variants of these defines to do this.
The 'has_op' define has been extended to have a grp_id argument as well, and
a mask variant has been added.
This extra argument required a change to go7007.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The ADV7180 supports NTSC, PAL and SECAM.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support to get the pixel aspect ratio depending on the current
standard (50 vs 60 Hz).
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support to get the standard to the adv7180 driver.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit 588afcc1c0 ("[media] usbvision fix overflow of interfaces
array")' should be reverted, because:
* "!dev->actconfig->interface[ifnum]" won't catch a case where the value
is not NULL but some garbage. This way the system may crash later with
GPF.
* "(ifnum >= USB_MAXINTERFACES)" does not cover all the error
conditions. "ifnum" should be compared to "dev->actconfig->
desc.bNumInterfaces", i.e. compared to the number of "struct
usb_interface" kzalloc()-ed, not to USB_MAXINTERFACES.
* There is a "struct usb_device" leak in this error path, as there is
usb_get_dev(), but no usb_put_dev() on this path.
* There is a bug of the same type several lines below with number of
endpoints. The code is accessing hard-coded second endpoint
("interface->endpoint[1].desc") which may not exist. It would be great
to handle this in the same patch too.
* All the concerns above are resolved by already-accepted commit fa52bd50
("[media] usbvision: fix crash on detecting device with invalid
configuration")
* Mailing list message:
http://www.spinics.net/lists/linux-media/msg94832.html
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.5
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix this smatch error:
dib0090.c:1124 dib0090_pwm_gain_reset() error: we previously assumed 'state->rf_ramp' could be null (see line 1086)
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
These are false positives, but still easy to fix.
pvrusb2-hdw.c:3676 pvr2_send_request_ex() error: we previously assumed 'write_data' could be null (see line 3648)
pvrusb2-hdw.c:3829 pvr2_send_request_ex() error: we previously assumed 'read_data' could be null (see line 3649)
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Set vb2_queue.gfp_flags to GFP_DMA32. Otherwise it will start to
create bounce buffers which is something you want to avoid since
those are in limited supply.
Without this patch, DMA scatter-gather may not work because
machines can ran out of buffers easily.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This commit introduces the support for the Techwell TW686x video
capture IC. This hardware supports a few DMA modes, including
scatter-gather and frame (contiguous).
This commit makes little use of the DMA engine and instead has
a memcpy based implementation. DMA frame and scatter-gather modes
support may be added in the future.
Currently supported chips:
- TW6864 (4 video channels),
- TW6865 (4 video channels, not tested, second generation chip),
- TW6868 (8 video channels but only 4 first channels using
built-in video decoder are supported, not tested),
- TW6869 (8 video channels, second generation chip).
[mchehab@osg.samsung.com: make checkpatch happy by using "unsigned int"
instead of just "unsigned"]
Cc: Krzysztof Halasa <khalasa@piap.pl>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Right now, the lock schema for media_device struct is messy,
since sometimes, it is protected via a spin lock, while, for
media graph traversal, it is protected by a mutex.
Solve this conflict by always using a mutex.
As a side effect, this prevents a bug when the media notifiers
is called at atomic context, while running the notifier callback:
BUG: sleeping function called from invalid context at mm/slub.c:1289
in_atomic(): 1, irqs_disabled(): 0, pid: 3479, name: modprobe
4 locks held by modprobe/3479:
#0: (&dev->mutex){......}, at: [<ffffffff81ce8933>] __driver_attach+0xa3/0x160
#1: (&dev->mutex){......}, at: [<ffffffff81ce8941>] __driver_attach+0xb1/0x160
#2: (register_mutex#5){+.+.+.}, at: [<ffffffffa10596c7>] usb_audio_probe+0x257/0x1c90 [snd_usb_audio]
#3: (&(&mdev->lock)->rlock){+.+.+.}, at: [<ffffffffa0e6051b>] media_device_register_entity+0x1cb/0x700 [media]
CPU: 2 PID: 3479 Comm: modprobe Not tainted 4.5.0-rc3+ #49
Hardware name: /NUC5i7RYB, BIOS RYBDWi35.86A.0350.2015.0812.1722 08/12/2015
0000000000000000 ffff8803b3f6f288 ffffffff81933901 ffff8803c4bae000
ffff8803c4bae5c8 ffff8803b3f6f2b0 ffffffff811c6af5 ffff8803c4bae000
ffffffff8285d7f6 0000000000000509 ffff8803b3f6f2f0 ffffffff811c6ce5
Call Trace:
[<ffffffff81933901>] dump_stack+0x85/0xc4
[<ffffffff811c6af5>] ___might_sleep+0x245/0x3a0
[<ffffffff811c6ce5>] __might_sleep+0x95/0x1a0
[<ffffffff8155aade>] kmem_cache_alloc_trace+0x20e/0x300
[<ffffffffa0e66e3d>] ? media_add_link+0x4d/0x140 [media]
[<ffffffffa0e66e3d>] media_add_link+0x4d/0x140 [media]
[<ffffffffa0e69931>] media_create_pad_link+0xa1/0x600 [media]
[<ffffffffa0fe11b3>] au0828_media_graph_notify+0x173/0x360 [au0828]
[<ffffffffa0e68a6a>] ? media_gobj_create+0x1ba/0x480 [media]
[<ffffffffa0e606fb>] media_device_register_entity+0x3ab/0x700 [media]
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
s32tmp in the below code may be negative, and dev->mclk_khz is an
unsigned type.
s32tmp = 0x10000 * (tuner_frequency - c->frequency);
s32tmp = DIV_ROUND_CLOSEST(s32tmp, dev->mclk_khz);
This is undefined, as DIV_ROUND_CLOSEST is undefined for negative
dividends when the divisor is of unsigned type.
So, change mclk_khz to be signed (s32).
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
