Every attempt to issue a read log page command lockup the controller.
The command is currently sent if the sata device includes the devlsp feature
to read out the timing data.
This attempt to read the data, locks up the controller and the device
is not recognzied correctly (failed to set xfermode) and cannot be accessed.
This was found on Freescale P1013/P1022 and T4240 CPUs
using a ATP IG mSATA 4GB with the devslp feature.
fsl-sata ff718000.sata: Sata FSL Platform/CSB Driver init
[ 1.254195] scsi0 : sata_fsl
[ 1.256004] ata1: SATA max UDMA/133 irq 74
[ 1.370666] fsl-gianfar ethernet.3: enabled errata workarounds, flags: 0x4
[ 1.470671] fsl-gianfar ethernet.4: enabled errata workarounds, flags: 0x4
[ 1.775584] ata1: Signature Update detected @ 504 msecs
[ 1.947594] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.948366] ata1.00: ATA-8: ATP IG mSATA, 20150311, max UDMA/133
[ 1.948371] ata1.00: 7732368 sectors, multi 0: LBA
[ 1.948843] ata1.00: failed to get Identify Device Data, Emask 0x1
[ 1.948857] ata1.00: failed to set xfermode (err_mask=0x40)
[ 7.467557] ata1: Signature Update detected @ 504 msecs
[ 7.639560] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 7.651320] ata1.00: failed to get Identify Device Data, Emask 0x1
[ 7.651360] ata1.00: failed to set xfermode (err_mask=0x40)
[ 7.655628] ata1: limiting SATA link speed to 1.5 Gbps
[ 7.659458] ata1.00: limiting speed to UDMA/133:PIO3
[ 13.163554] ata1: Signature Update detected @ 504 msecs
[ 13.335558] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 13.347298] ata1.00: failed to get Identify Device Data, Emask 0x1
[ 13.347334] ata1.00: failed to set xfermode (err_mask=0x40)
[ 13.351601] ata1.00: disabled
[ 13.353278] ata1: exception Emask 0x50 SAct 0x0 SErr 0x800 action 0x6 frozen t4
[ 13.359281] ata1: SError: { HostInt }
[ 13.361644] ata1: hard resetting link
Signed-off-by: Andreas Werner <andreas.werner@men.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
The driver was ignoring limits requested by libata.force. The output
would look like:
fsl-sata ffe18000.sata: Sata FSL Platform/CSB Driver init
ata1: FORCE: PHY spd limit set to 1.5Gbps
ata1: SATA max UDMA/133 irq 74
ata1: Signature Update detected @ 0 msecs
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 310)
Signed-off-by: Martin Hicks <mort@bork.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
irq_of_parse_and_map() returns 0 on error (the result is unsigned int),
so testing for negative result never works.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Use the zeroing function instead of dma_alloc_coherent & memset(,0,)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
A check for CONFIG_MPC8315_DS was added in v2.6.24. But the related
Kconfig symbol was never added to the tree. So the code behind this
check has effectively been dead for over six years. Remove it.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch fixes host drivers to use CONFIG_PM_SLEEP instead of CONFIG_PM
where applicable. Benefits of this change:
* unused code is not being compiled in for CONFIG_PM=y, CONFIG_PM_SLEEP=n
and CONFIG_PM_RUNTIME=y configurations
* easier transition to use struct dev_pm_ops and SIMPLE_DEV_PM_OPS() in
the future
* more consistent code (there are host drivers which are using the correct
CONFIG_PM_SLEEP checks already)
The patch leaves the core libata code and ->port_[suspend,resume] support
in sata_[inic162x,nv,sil24].c alone for now.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Powerpc is a mess of implicit includes by prom.h. Add the necessary
explicit includes to drivers in preparation of prom.h cleanup.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Also, unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
2) Minor cleanups for sata_highbank, pata_at32, pata_octeon_cf,
sata_rcar
3) pata_legacy: small bug found in opti chipset code (untested fix,
due to ancient h/w)
4) sata_fsl: RX water mark config knob, some h/w needs it
5) pata_imx: cleanups, DeviceTree support
6) SCSI<->ATA translator: properly export translator version,
not device firmware version
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=kLMT
-----END PGP SIGNATURE-----
Merge tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
Pull libata update from Jeff Garzik:
- More ACPI fixes, cleanups
- Minor cleanups for sata_highbank, pata_at32, pata_octeon_cf,
sata_rcar
- pata_legacy: small bug found in opti chipset code (untested fix, due
to ancient h/w)
- sata_fsl: RX water mark config knob, some h/w needs it
- pata_imx: cleanups, DeviceTree support
- SCSI<->ATA translator: properly export translator version, not device
firmware version
* tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
sata_highbank: Rename proc_name to the module name
ACPI/libata: Restore libata.noacpi support
[libata] acpi: make ata_ap_acpi_handle not block
[libata] SCSI: really use SATL version in VPD
pata_imx: add devicetree support
pata_imx: use void __iomem * for regs
pata_imx: cleanup error path
pata_imx: Use devm_clk_get
sata_rcar: Convert to devm_ioremap_resource()
fsl/sata: create a sysfs entry for rx water mark
libata-acpi: remove redundent code for power resource handling
sata_highbank: make ahci_highbank_pm_ops static
pata_octeon_cf: Use resource_size function
pata_legacy: bogus clock in opti82c46x_set_piomode()
pata_at32: use module_platform_driver_probe()
Support config RX WATER MARK via sysfs when running at run-time;
A wrokaround for fix the exception happened to some WD HDD, found on
WD3000HLFS-01G6U1, WD3000HLFS-01G6U0, some SSD disks. The read performance
is also regression (about 30%) when use default value.
According to the latest documents, 0x10 is the default value of RX WATER MARK,
but exception/performance issue happened to some disks mentioned above.
The exception log as below when testing read performance with IOZone:
ata1.00: exception Emask 0x0 SAct 0x7 SErr 0x800000 action 0x6 frozen
ata1: SError: { LinkSeq }
ata1.00: failed command: READ FPDMA QUEUED
ata1.00: cmd 60/00:00:ff:2c:14/01:00:02:00:00/40 tag 0 ncq 131072 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata1.00: status: { DRDY }
ata1.00: failed command: READ FPDMA QUEUED
ata1.00: cmd 60/00:08:ff:2d:14/01:00:02:00:00/40 tag 1 ncq 131072 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata1.00: status: { DRDY }
ata1.00: failed command: WRITE FPDMA QUEUED
ata1.00: cmd 61/10:10:af:08:6e/00:00:12:00:00/40 tag 2 ncq 8192 out
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata1.00: status: { DRDY }
ata1: hard resetting link
ata1: Hardreset failed, not off-lined 0
ata1: Signature Update detected @ 504 msecs
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: configured for UDMA/133
ata1.00: device reported invalid CHS sector 0
ata1.00: device reported invalid CHS sector 0
ata1.00: device reported invalid CHS sector 0
ata1: EH complete
The exception/performance can be resolved when RX WATER MARK value is 0x16.
Signed-off-by: Qiang Liu <qiang.liu@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The freescale V2 SATA controller checks if the received data length matches
the programmed length 'ttl', if not, it assumes that this is an error.
In ATAPI, the 'ttl' is based on max allocation length and not the actual
data transfer length, controller will raise 'DLM' (Data length Mismatch)
error bit in Hstatus register. Along with 'DLM', DE (Device error) and
FE (fatal Error) bits are also set in Hstatus register, 'E' (Internal Error)
bit is set in Serror register and CE (Command Error) and DE (Device error)
registers have the corresponding bit set. In this condition, we need to
clear errors in following way: in the service routine, based on 'DLM' flag,
HCONTROL[27] operation clears Hstatus, CE and DE registers, clear Serror
register.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Anju Bhartiya <Anju.Bhartiya@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Adds support for interrupt coalescing feature to reduce interrupt events.
Provides a mechanism of adjusting coalescing count and timeout tick by sysfs
at runtime, so that tradeoff of latency and CPU load can be made depending
on different applications.
Signed-off-by: Qiang Liu <qiang.liu@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Configure the FSL SATA controller to the preferred, enterprise mode.
Signed-off-by: Yutaka Ando <r46913@freescale.com>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
CC: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch converts the drivers in drivers/ata/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Cc: Viresh Kumar <viresh.kumar@st.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Sylvain Munaut <tnt@246tNt.com>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Mark Miesfeld <mmiesfeld@amcc.com>
Cc: Ashish Kalra <ashish.kalra@freescale.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Saves a bit of text as the call takes fewer args.
Coalesce a few formats.
Convert a few bare printks to pr_cont.
$ size drivers/ata/built-in.o*
text data bss dec hex filename
558429 73893 117864 750186 b726a drivers/ata/built-in.o.allyesconfig.new
559574 73893 117888 751355 b76fb drivers/ata/built-in.o.allyesconfig.old
149567 14689 4220 168476 2921c drivers/ata/built-in.o.defconfig.new
149851 14689 4220 168760 29338 drivers/ata/built-in.o.defconfig.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
In FSL sata v2 block, the snoop bit of PRDT Word3 description
information is at bit28 instead of bit22.
This patch adds FSL sata v2 probe and resolve this difference.
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
RX_WATER_MARK sets the number of locations in Rx FIFO that can be used before
the transport layer instructs the link layer to transmit HOLDS. Note that it
can take some time for the HOLDs to get to the other end, and that in the
interim there must be enough room in the FIFO to absorb all data that could
arrive.
Update the new recommended value to 16.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
When a single device error is detected, the device under the error
is indicated by the error bit set in the DER. There is a one to one
mapping between register bit and devices on Port multiplier(PMP)
i.e. bit 0 represents PMP device 0 and bit 1 represents PMP device
1 etc.
Current implementation treats Device error register value as device
number not set of bits representing multiple device on PMP. It is
changed to consider bit level.
No need to check for each set bit as all command is going to be
aborted.
Signed-off-by: Ashish Kalra <B00888@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
All checks of ATA_FLAG_NO_LEGACY have been removed by the commits
c791c30670 ([libata] minor PCI IDE probe
fixes and cleanups) and f0d36efdc6 (libata:
update libata core layer to use devres), so I think it's time to finally
get rid of this flag...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 0d5ff56677 (libata: convert to iomap)
removed all checks of ATA_FLAG_MMIO but neglected to remove the flag itself.
Do it now, at last...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Final step to eliminate of_platform_bus_type. They're all just
platform drivers now.
v2: fix type in pasemi_nand.c (thanks to Stephen Rothwell)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add optional @ap argument to ata_wait_register() and replace msleep()
calls with ata_msleep() which take optional @ap in addition to the
duration. These will be used to implement EH exclusion.
This patch doesn't cause any behavior difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Currently, sata_fsl, mv and nv call ata_qc_complete() multiple times
from their interrupt handlers to indicate completion of NCQ commands.
This limits the visibility the libata core layer has into how commands
are being executed and completed, which is necessary to support IRQ
expecting in generic way. libata already has an interface to complete
multiple commands at once - ata_qc_complete_multiple() which ahci and
sata_sil24 already use.
This patch updates the three drivers to use ata_qc_complete_multiple()
too and updates comments on ata_qc_complete[_multiple]() regarding
their usages with NCQ completions. This change not only provides
better visibility into command execution to the core layer but also
simplifies low level drivers.
* sata_fsl: It already builds done_mask. Conversion is straight
forward.
* sata_mv: mv_process_crpb_response() no longer checks for illegal
completions, it just returns whether the tag is completed or not.
mv_process_crpb_entries() builds done_mask from it and passes it to
ata_qc_complete_multiple() which will check for illegal completions.
* sata_nv adma: Similar to sata_mv. nv_adma_check_cpb() now just
returns the tag status and nv_adma_interrupt() builds done_mask from
it and passes it to ata_qc_complete_multiple().
* sata_nv swncq: It already builds done_mask. Drop unnecessary
illegal transition checks and call ata_qc_complete_multiple().
In the long run, it might be a good idea to make ata_qc_complete()
whine if called when multiple NCQ commands are in flight.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ashish Kalra <ashish.kalra@freescale.com>
Cc: Saeed Bishara <saeed@marvell.com>
Cc: Mark Lord <liml@rtr.ca>
Cc: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
of_device is just an alias for platform_device, so remove it entirely. Also
replace to_of_device() with to_platform_device() and update comment blocks.
This patch was initially generated from the following semantic patch, and then
edited by hand to pick up the bits that coccinelle didn't catch.
@@
@@
-struct of_device
+struct platform_device
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: David S. Miller <davem@davemloft.net>
Make the following changes to prepare for NCQ command completion
update. Changes made by this patch don't cause any functional
difference.
* sata_fsl_host_intr(): rename the local variable qc_active to
done_mask as that's what it is.
* mv_process_crpb_response(): restructure if clause for easier update.
* nv_adma_interrupt(): drop unnecessary error variable.
* nv_swncq_sdbfis(): drop unnecessary nr_done and return 0 on success.
Typo fix.
* nv_swncq_dmafis(): drop unused return value and return void.
* nv_swncq_host_interrupt(): drop unnecessary return value handling.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ashish Kalra <ashish.kalra@freescale.com>
Cc: Saeed Bishara <saeed@marvell.com>
Cc: Mark Lord <liml@rtr.ca>
Cc: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
.name, .match_table and .owner are duplicated in both of_platform_driver
and device_driver. This patch is a removes the extra copies from struct
of_platform_driver and converts all users to the device_driver members.
This patch is a pretty mechanical change. The usage model doesn't change
and if any drivers have been missed, or if anything has been fixed up
incorrectly, then it will fail with a compile time error, and the fixup
will be trivial. This patch looks big and scary because it touches so
many files, but it should be pretty safe.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
The following structure elements duplicate the information in
'struct device.of_node' and so are being eliminated. This patch
makes all readers of these elements use device.of_node instead.
(struct of_device *)->node
(struct dev_archdata *)->prom_node (sparc)
(struct dev_archdata *)->of_node (powerpc & microblaze)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Enable device hot-plug support on Port multiplier fan-out ports
Signed-off-by: Ashish Kalra <Ashish.Kalra@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Split sata_fsl_softreset() into hard and soft resets to make
error-handling more efficient & device and PMP detection more
reliable.
Also includes fix for PMP support, driver tested with Sil3726,
Sil4726 & Exar PMP controllers.
[AV: Also fixes resuming from deep sleep on MPC8315 CPUs]
Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix for non-ncq & ncq commands causing timeouts when both are issued
simultaneously to the same device.
Signed-off-by: Ashish Kalra <Ashish.Kalra@freescale.com>
[fixed to be actual compileable C code -jg]
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The bit 11 of command description is reserved bit in Freescale
SATA controller and needs to be set to '1'. This is needed to
make sure the last write from the controller to the buffer
descriptor is seen before an interrupt is raised.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We we build with dma_addr_t as a 64-bit quantity we get:
drivers/ata/sata_fsl.c: In function 'sata_fsl_fill_sg':
drivers/ata/sata_fsl.c:340: warning: format '%x' expects type 'unsigned int', but argument 4 has type 'dma_addr_t'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
while I was looking over kernel sources I've found this small bug.
Formerly, zero was returned even if an error happened.
Signed-off-by: Michal Sojka <sojkam1@fel.cvut.cz>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
