The touchkey variant found on aries board is slighty different,
it uses a fixed regulator and writes/read to the same place
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Not all devices use the same keycodes in the same order,
so add possibility to define keycodes for buttons present
on actual hardware.
If keycodes property is not present, we assume that device has
at least MENU and BACK keys.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
tm2-touchkey doesn't have brightness levels, but only on/off states,
so replace LED_FULL with LED_ON.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The touchkey on midas boards is almost identical.
The only real difference is that it uses the same register for both
keycode and base.
Signed-off-by: Simon Shields <simon@lineageos.org>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Microsoft documenation for the PNP0C40 device aka the
"Windows-compatible button array" describes the 5th GpioInt listed in
the resources as: '5. Interrupt corresponding to the "Rotation Lock"
button, if supported'.
Notice this describes the 5th entry as a button while we sofar have been
mapping it to EV_SW, SW_ROTATE_LOCK. On my Point of View TAB P1006W-232
which actually comes with a rotation-lock button, the button indeed is a
button and not a slider/switch. An image search for other Windows tablets
has found 2 more models with a rotation-lock button and on both of those
it too is a push-button and not a slider/switch.
Further evidence can be found in the HUT extension HUTRR52 from Microsoft
which adds rotation lock support to the HUT, which describes 2 different
usages: "0xC9 System Display Rotation Lock Button" and
"0xCA System Display Rotation Lock Slider Switch" note that switch is seen
as a separate thing here and the non switch wording is an exact match for
the "Windows-compatible button array" spec wording.
TL;DR: our current mapping of the 5th GPIO to SW_ROTATE_LOCK is wrong
because the 5th GPIO is for a push-button not a switch.
This commit fixes this by maping the 5th GPIO to KEY_ROTATE_LOCK_TOGGLE.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The ACPI0011 _DSD button descriptor on a CHT based Intel Compute Sticks
contains a mapping for usage-page 0x01 usage-id 0xca.
As described in hutrr52_system_display_rotation_lock_controls_0.pdf this
should be mapped as a "System Display Rotation Lock Slider Switch", this
commit adds support for this, silencing the following warning:
soc_button_array ACPI0011:00: Unknown button index 4 upage 01 usage ca,
ignoring
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If the user attempts to update Atmel device with an invalid configuration
cfg file, error handling code is trying to free cfg file memory which is
not allocated yet hence results into kernel crash.
This patch fixes the order of memory free operations.
Signed-off-by: Sanjeev Chugh <sanjeev_chugh@mentor.com>
Fixes: a4891f1058 ("Input: atmel_mxt_ts - zero terminate config firmware file")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There are some statements that are indented incorrectly, fix this by
removing the extra tabs.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch fixes the coding style problem reported
by checkpatch.pl as below:
ERROR: foo* bar should be "foo *bar"
Signed-off-by: Hardik Singh Rathore <hardiksingh.k@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add's support to Raspberry Pi's 7" Touch device. Instead of using a
conventional bus all information is copied into a memory mapped area by
RPi's firmware.
Based on the driver found in RPi's kernel repository.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The loop exits with "timeout" set to -1 not to 0.
Fixes: 1158f0f162 ("Input: add support for Nomadik SKE keypad controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When a driver fails to bind because a resource it still missing it's not
helpful to report this as (usually) probing is repeated later.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/input/serio/olpc_apsp.c: In function 'olpc_apsp_probe':
drivers/input/serio/olpc_apsp.c:192:22: warning:
variable 'np' set but not used [-Wunused-but-set-variable]
It never used since introduction in commit b56ece9a3a ("Input: add OLPC
AP-SP driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Without the clock, the keyboard controller won't operate.
Tested on an OLPC XO 1.75.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's defer the FIFO status checking until open().
When we'll get a clk handle, this will allow us to defer clock enablement
until the device is actually used.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CONFIG_OLPC is specific to the x86 platform code, while the driver is for
an ARM-based laptop.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The "security processor", sometimes referred to as "wireless trusted
module" or "generic encrypt unit" is a low-power core present on MMP2,
that has nothing to do with security, wireless, trust or encryption.
On an OLPC machine it runs CForth and serves as a keyboard controller:
http://dev.laptop.org/git/users/wmb/cforth/tree/src/app/arm-xo-1.75/ps2.fth
The register address was obtained from the OLPC kernel, since the
datasheet seems to be the Marvell's most important business secret.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is the clock for the "security processor" core.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This driver supports configuration via platform data but
absolutely nothing in the upstream kernel uses it. Since this
configuration allows harmful practices such as encoding the
GPIO base for the chip, delete platform data support so that
no new platform using it gets introduced.
Also: include the right driver header, not <linux/gpio.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
synaptics_detect() does not check whether sending commands to the
device succeeds and instead relies on getting unique data from the
device. Let's make sure we seed entire buffer with zeroes to make sure
we will not use garbage on stack that just happen to be 0x47.
Reported-by: syzbot+13cb3b01d0784e4ffc3f@syzkaller.appspotmail.com
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case, I placed the "fall through"
part at the beginning of the code comment, which is what GCC is
expecting to find.
Addresses-Coverity-ID: 114757 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case, I replaced the "Fallthrough state"
commern with a proper "Fall through", which is what GCC is expecting to
find.
Addresses-Coverity-ID: 114758 ("Missing break in switch")
Addresses-Coverity-ID: 114759 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Loading then unloading wm97xx-ts.ko when CONFIG_AC97_BUS=m
causes a WARNING: from drivers/base/driver.c:
Unexpected driver unregister!
WARNING: CPU: 0 PID: 1709 at ../drivers/base/driver.c:193 driver_unregister+0x30/0x40
Fix this by only calling driver_unregister() with the same
condition that driver_register() is called.
Fixes: ae9d1b5fbd ("Input: wm97xx: add new AC97 bus support")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some touchscreens, depending on the firmware and/or the digitizer, report
coordinates which never reach 0 along one or both of their axis.
This has been seen for example on the Silead touchscreens on a Onda V891w
and a Point of View mobii TAB-P800w(v2.0).
This commit adds support for touchscreen-min-x and touchscreen-min-y
device-properties which can be set to communicate the actual start
coordinates (rather then 0,0) to userspace.
This commit also drop the "(in pixels)" comment from the documentation
of the touchscreen-size-x and touchscreen-size-y properties. The comment
suggested that there is a relation between the range of reported
coordinates and the display resolution, which is only true for some
devices. The "(in pixels)" comment is replaced with "(maximum x coordinate
reported + 1)" to mirror the language describing the new touchscreen-min-x
and -min-y properties.
When set this fixes e.g. not being able to click things in the GNOME3
top-bar on the 2 example tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The path was incomplete, fix it.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
To avoid bounce buffer when an i2c controller decides to use DMA for a
transaction, let's make out buffer that we use for reads DMA-safe and let
the master know that DMAing into it is safe.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
A certain silead controller (Chip ID: 0x56810000) loses its firmware
after suspend, causing the resume to fail. This patch tries to load
the firmware, should a resume error occur and retries the resuming.
Signed-off-by: Julian Sax <jsbc@gmx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is how userspace checks for touchscreen devices most reliably.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Both v4.16-rc7 commit 93afb1d6e7 ("Input: atmel_mxt_ts - switch from
OF to generic device properties") and v4.16-rc7 commit 96a938aa21
("Input: atmel_mxt_ts - remove platform data support") added includes of
"<linux/property.h>". Remove one of the duplicate includes to fix this.
Signed-off-by: George G. Davis <george_davis@mentor.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In the example for the pwm-vibrator bindings, pwm8 is the direction pin,
and pwm9 is the enable pin. The pwms on the vibrator node has these two
values swapped so this patch corrects it.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some of fuzzers set panic_on_warn=1 so that they can handle WARN()ings
the same way they handle full-blown kernel crashes. We used WARN() in
input_alloc_absinfo() to get a better idea where memory allocation
failed, but since then kmalloc() and friends started dumping call stack on
memory allocation failures anyway, so we are not getting anything extra
from WARN().
Because of the above, let's replace WARN with dev_err(). We use dev_err()
instead of simply removing message and relying on kcalloc() to give us
stack dump so that we'd know the instance of hardware device to which we
were trying to attach input device.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Warning level 2 was used: -Wimplicit-fallthrough=2
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Switch to bitmap API, i.e. bitmap_alloc(), bitmap_zalloc(), to show
clearly what we are allocating. Besides that it returns pointer of
bitmap type instead of opaque void *.
While here, replace memcpy() with bitmap_copy() for sake of consistency.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Switch to bitmap_zalloc() to show clearly what we are allocating.
Besides that it returns pointer of bitmap type instead of opaque void *.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
A lot of code become ugly because of open coding allocations for bitmaps.
Introduce three helpers to allow users be more clear of intention
and keep their code neat.
Note, due to multiple circular dependencies we may not provide
the helpers as inliners. For now we keep them exported and, perhaps,
at some point in the future we will sort out header inclusion and
inheritance.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
bitmap API (include/linux/bitmap.h) has 'bitmap' prefix for its methods.
On the other hand MD bitmap API is special case.
Adding 'md' prefix to it to avoid name space collision.
No functional changes intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Shaohua Li <shli@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
bitmap API (include/linux/bitmap.h) has 'bitmap' prefix for its methods.
On the other hand DM bitmap API is special case.
Adding 'dm' prefix to it to avoid potential name space collision.
No functional changes intended.
Suggested-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since handling is abstracted in this driver, we need to add resin entry
in id table along with pwrkey_data.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In order to support resin thru the pwrkey driver (they are very
similar in nature) we need to abstract the handling in this driver.
First we abstract pull_up_bit and status_bit along in driver data.
The event code sent for key events is quiried from DT.
Since the device can be child of pon lookup regmap and reg from
parent if lookup fails (we are child).
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* btn_avb_pegasus and btn_avb_tw are the same. Unify them
into btn_joystick_avb.
* btn_wheel is an exact copy of btn_joystick, so remove it.
Rename btn_avb_wheel into btn_wheel since it is the only
sane configuration for a wheel.
* Assign the (new) btn_wheel configuration to the "AVB Top
Shot Force Feedback Racing Wheel", because the previous
configuration was meant for a joystick.
Signed-off-by: Tim Schumacher <timschumi@gmx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If T9.CTRL DISAMP is set, then pressure is reported as zero. This means
some app layers (eg tslib) will ignore the contact.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We use sscanf to parse the configuration file, so it's necessary to zero
terminate the configuration otherwise a truncated file can cause the
parser to run off into uninitialised memory.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On devices with the T71 object, the config CRC will start there, rather
than at T7.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
