As the vid_list is only accessed from process context, there's no need to
protect it with a spinlock.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both qeth sub drivers use the same QDIO queue handlers, there's no need
to expose them via the driver's discipline. No functional change.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For control IO, qeth currently tracks the index of the buffer that it
expects to complete the next IO on each qeth_channel. If the channel
presents an IRQ while this buffer has not yet completed, no completion
processing for _any_ completed buffer takes place.
So if the 'next buffer' is skipped for any sort of reason* (eg. when it
is released due to error conditions, before the IO is started), the
buffer obviously won't switch to PROCESSED until it is eventually
allocated for a _different_ IO and completes.
Until this happens, all completion processing on that channel stalls
and pending requests possibly time out.
As a fix, remove the whole 'next buffer' logic and simply process any
IO buffer right when it completes. A channel will never have more than
one IO pending, so there's no risk of processing out-of-sequence.
*Note: currently just one location in the code really handles this problem,
by advancing the 'next' index manually.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using up 8 bytes in every ipaddr object to store SETIP/DELIP flags is
rather wasteful. Except for takeover eligibility, the flag values all
just depend on the address type, so determine them on demand.
While at it reorder the struct to fill an alignment hole.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On an IP event, current code tries to determine if the netdev belongs
to a L3 card by walking all qeth cards in the system, and then all of
their VLAN devices too. Short-cut the whole thing by identifying a L3
device through its netdev_ops.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
send_control_data() applies some special handling to SETIP v4 IPA
commands. But current code parses *all* command types for the SETIP
command code. Limit the command code check to IPA commands.
Fixes: 5b54e16f1a ("qeth: do not spin for SETIP ip assist command")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For a memory range/skb where the last byte falls onto a page boundary
(ie. 'end' is of the form xxx...xxx001), the PFN_UP() part of the
calculation currently doesn't round up to the next PFN due to an
off-by-one error.
Thus qeth believes that the skb occupies one page less than it
actually does, and may select a IO buffer that doesn't have enough spare
buffer elements to fit all of the skb's data.
HW detects this as a malformed buffer descriptor, and raises an
exception which then triggers device recovery.
Fixes: 2863c61334 ("qeth: refactor calculation of SBALE count")
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The L3 packet descriptor's 'dest_addr' field is used for a different
purpose in RX descriptors. Clean up the hard-coded byte accesses and
try to be more self-documenting.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When
1. an skb has no neighbour, and
2. skb->protocol is not IP[V6],
we select the skb's cast type based on its destination MAC address.
The multicast check is currently restricted to Multicast IP-mapped MACs.
Extend it to also cover non-IP Multicast MACs.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the proper helpers to check for multicast IP addressing, and remove
some ancient Token Ring code.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of assuming that skb->data points to the Ethernet header, use
the right helper and struct to access the Ethertype field.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
atomic_t variables are currently used to implement reference
counters with the following properties:
- counter is initialized to 1 using atomic_set()
- a resource is freed upon counter reaching zero
- once counter reaches zero, its further
increments aren't allowed
- counter schema uses basic atomic operations
(set, inc, inc_not_zero, dec_and_test, etc.)
Such atomic variables should be converted to a newly provided
refcount_t type and API that prevents accidental counter overflows
and underflows. This is important since overflows and underflows
can lead to use-after-free situation and be exploitable.
The variable qeth_reply.refcnt is used as pure reference counter.
Convert it to refcount_t and fix up the operations.
Suggested-by: Kees Cook <keescook@chromium.org>
Reviewed-by: David Windsor <dwindsor@gmail.com>
Reviewed-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
[jwi: removed the WARN_ONs. Use CONFIG_REFCOUNT_FULL if you care.]
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Any modification to the takeover IP-ranges requires that we re-evaluate
which IP addresses are takeover-eligible. Otherwise we might do takeover
for some addresses when we no longer should, or vice-versa.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just as for an explicit enable/disable, toggling the takeover mode also
requires that the IP addresses get updated. Otherwise all IPs that were
added to the table before the mode-toggle, get registered with the old
settings.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using GSO with small MTUs currently results in a substantial throughput
regression - which is caused by how qeth needs to map non-linear skbs
into its IO buffer elements:
compared to a linear skb, each GSO-segmented skb effectively consumes
twice as many buffer elements (ie two instead of one) due to the
additional header-only part. This causes the Output Queue to be
congested with low-utilized IO buffers.
Fix this as follows:
If the MSS is low enough so that a non-SG GSO segmentation produces
order-0 skbs (currently ~3500 byte), opt out from NETIF_F_SG. This is
where we anticipate the biggest savings, since an SG-enabled
GSO segmentation produces skbs that always consume at least two
buffer elements.
Larger MSS values continue to get a SG-enabled GSO segmentation, since
1) the relative overhead of the additional header-only buffer element
becomes less noticeable, and
2) the linearization overhead increases.
With the throughput regression fixed, re-enable NETIF_F_SG by default to
reap the significant CPU savings of GSO.
Fixes: 5722963a8e ("qeth: do not turn on SG per default")
Reported-by: Nils Hoppmann <niho@de.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With commit "s390/ccwgroup: tie a ccwgroup driver to its ccw driver",
the ccwgroup core now ensures that a qeth group device only consists of
ccw devices which are supported by qeth. Therefore remove qeth's
internal device matching, and use .driver_info to determine the card
type.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When recovering a device, qeth needs to re-run the IPA commands that
enable all previously active HW features.
Instead of duplicating qeth_set_features(), let netdev_update_features()
recover the missing HW features from dev->wanted_features.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cppcheck reports the following for drivers/s390/net/qeth_core.h:
warning - line 1560 - Function 'qeth_do_send_packet' argument order
different:
declaration 'card, queue, skb, hdr, hd_len, offset, elements'
definition 'card, queue, skb, hdr, offset, hd_len, elements_needed'.
Match the naming in the function's declaration against its definition.
Signed-off-by: Jens Remus <jremus@linux.vnet.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Locking the output queue prior to TX is needed on OSA devices,
to synchronize against a packing flush from the TX completion code
(via qeth_check_outbound_queue()).
But send_packet_fast() is only used for IQDs, which don't do packing.
So remove the locking, and apply some easy cleanups.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HiperSockets allow configuring so called VNIC Characteristics (VNICC)
that influence how the underlying hardware handles packets. For VNICCs,
additional commands for getting and setting timeouts are available.
Currently, the learning VNICC uses these commands.
* Learning VNICC: If learning is enabled on a qeth device, the device
learns the source MAC addresses of outgoing packets and incoming
packets to those learned MAC addresses are received.
For learning, the timeout specifies the idle period in seconds, after
which the underlying hardware removes a learned MAC address again.
This patch adds support for the IPA commands that are required to get
and set the current timeout values for the learning VNIC characteristic.
Also, it introduces the sysfs interface that allows users to configure
the timeout.
Signed-off-by: Hans Wippel <hwippel@linux.vnet.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HiperSocket devices allow enabling and disabling so called VNIC
Characteristics (VNICC) that influence how the underlying hardware
handles packets. These VNICCs are:
* Flooding VNICC: Flooding allows specifying if packets to unknown
destination MAC addresses are received by the qeth device.
* Multicast flooding VNICC: Multicast flooding allows specifying if
packets to multicast MAC addresses are received by the qeth device.
* Learning VNICC: If learning is enabled on a qeth device, the device
learns the source MAC addresses of outgoing packets and incoming
packets to those learned MAC addresses are received.
* Takeover setvmac VNICC: If takeover setvmac is configured on a qeth
device, the MAC address of this device can be configured on a
different qeth device with the setvmac IPA command.
* Takeover by learning VNICC: If takeover learning is enabled on a qeth
device, the MAC address of this device can be learned (learning VNICC)
on a different qeth device.
* BridgePort invisible VNICC: If BridgePort invisible is enabled on a
qeth device, (1) packets from this device are not sent to a BridgePort
enabled qeth device and (2) packets coming from a BridgePort enabled
qeth device are not received by this device.
* Receive broadcast VNICC: Receive broadcast allows configuring if a
qeth device receives packets with the broadcast destination MAC
address.
This patch adds support for the IPA commands that are required to enable
and disable these VNIC characteristics on qeth devices. As a
prerequisite, it also adds the query commands IPA command.
The query commands IPA command allows requesting the supported commands
for each characteristic from the underlying hardware.
Additionally, this patch provides users with a sysfs user interface to
enable/disable the VNICCs mentioned above.
Signed-off-by: Hans Wippel <hwippel@linux.vnet.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VNIC Characteristics (VNICC) are features of HiperSockets that define
how packets are handled by the underlying network hardware. For example,
if the VNICC flooding is configured on a qeth device, ethernet frames to
unknown destination MAC addresses are received.
Currently, there is support for seven VNICCs: flooding, multicast
flooding, receive broadcast, learning, takeover learning, takeover
setvmac, bridge invisible. Also, six IPA commands exist for configuring
VNICCs on a qeth device: query characteristics, query commands, enable
characteristic, disable characteristic, set timeout, get timeout.
This patch adds the basic code infrastructure for VNICC support to qeth.
It allows querying VNICC support from the underlying hardware. To this
end, it adds:
* basic message formats for IPA commands
* basic data structures
* basic error handling
* query characteristics IPA command support
The query characteristics IPA command allows requesting the currently
supported and currently enabled VNIC characteristics from the underlying
hardware.
Support for the other IPA commands and for the configuration of VNICCs
is added in follow-up patches together with the respective user
interface functions.
Signed-off-by: Hans Wippel <hwippel@linux.vnet.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Taking a full copy via skb_realloc_headroom() on every xmit is overkill
and wastes CPU time; all we actually need is to push on the qeth_hdr.
So rework the L2 OSA TX path to avoid the copy.
Minor complications arise because struct qeth_hdr must not cross a page
boundary. So add a new helper qeth_push_hdr() that catches this, and
falls back to the hdr cache that we already use for IQDs.
This change uncovered that qeth's TX completion takes rather long.
Now that we no longer free the original skb straight away and thus call
skb->destructor later than before, throughput regresses significantly.
For now, restore old behaviour by adding an explicit skb_orphan(),
and a big TODO to improve the TX completion time.
Tested-by: Nils Hoppmann <niho@de.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For TSO we need to skip the skb's qeth/IP/TCP headers when mapping
it into buffer elements. Instead of (mis)using skb_pull(), pass a
corresponding offset to fill_buffer() like we already do for IQDs.
No actual change in the resulting TSO buffers.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TSO code already calculates the length of its header element,
no need to duplicate this in the low-level code again.
Use this opportunity to make hd_len unsigned, and for TSO match
its calculation to what tso_fill_header() does.
No functional change.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace some open-coded parts with their proper API calls.
Also remove two skb_[re]set_mac_header() calls in the L2
xmit paths that are clearly no longer required, since at least
commit 6d1ccff627 ("net: reset mac header in dev_start_xmit()").
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For some xmit paths we pass down a data offset to qeth_fill_buffer(),
to indicate that the first k bytes of the skb should be skipped when
mapping it into buffer elements.
Commit acd9776b5c ("s390/qeth: no ETH header for outbound AF_IUCV")
recently switched the offset for the IUCV-over-HiperSockets path
from 0 to ETH_HLEN, and now we have
device offset
OSA = 0
IQD > 0
for all xmit paths.
OSA would previously pass down -1 from do_send_packet(), to distinguish
between 1) OSA and 2) IQD with offset 0. That's no longer needed now,
so have it pass 0, make the offset unsigned and clean up how we apply
the offset in __qeth_fill_buffer().
No change of behaviour for any of our current xmit paths.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a s390 guest runs on a z/VM host that's part of a SSI cluster,
it can be migrated to a different host. In this case, the MAC address
it originally obtained on the old host may be re-assigned to a new
guest. This would result in address conflicts between the two guests.
When running as z/VM guest, use the diag26c MAC Service to obtain
a hypervisor-managed MAC address. The MAC Service is SSI-aware, and
won't re-assign the address after the guest is migrated to a new host.
This patch adds support for the z/VM MAC Service on L2 devices.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth currently supports early setup for OSM and OSN devices.
This patch adds early setup support for z/VM HiperSockets,
since they can only be coupled to L3 networks.
Based on an initial version by Dmitriy Lakhvich.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit b4d72c08b3 ("qeth: bridgeport support - basic control")
broke the support for OSM and OSN devices as follows:
As OSM and OSN are L2 only, qeth_core_probe_device() does an early
setup by loading the l2 discipline and calling qeth_l2_probe_device().
In this context, adding the l2-specific bridgeport sysfs attributes
via qeth_l2_create_device_attributes() hits a BUG_ON in fs/sysfs/group.c,
since the basic sysfs infrastructure for the device hasn't been
established yet.
Note that OSN actually has its own unique sysfs attributes
(qeth_osn_devtype), so the additional attributes shouldn't be created
at all.
For OSM, add a new qeth_l2_devtype that contains all the common
and l2-specific sysfs attributes.
When qeth_core_probe_device() does early setup for OSM or OSN, assign
the corresponding devtype so that the ccwgroup probe code creates the
full set of sysfs attributes.
This allows us to skip qeth_l2_create_device_attributes() in case
of an early setup.
Any device that can't do early setup will initially have only the
generic sysfs attributes, and when it's probed later
qeth_l2_probe_device() adds the l2-specific attributes.
If an early-setup device is removed (by calling ccwgroup_ungroup()),
device_unregister() will - using the devtype - delete the
l2-specific attributes before qeth_l2_remove_device() is called.
So make sure to not remove them twice.
What complicates the issue is that qeth_l2_probe_device() and
qeth_l2_remove_device() is also called on a device when its
layer2 attribute changes (ie. its layer mode is switched).
For early-setup devices this wouldn't work properly - we wouldn't
remove the l2-specific attributes when switching to L3.
But switching the layer mode doesn't actually make any sense;
we already decided that the device can only operate in L2!
So just refuse to switch the layer mode on such devices. Note that
OSN doesn't have a layer2 attribute, so we only need to special-case
OSM.
Based on an initial patch by Ursula Braun.
Fixes: b4d72c08b3 ("qeth: bridgeport support - basic control")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
prepare() and complete() are not implemented by any discipline, so just
drop all the indirection.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Hans Wippel <hwippel@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
get_settings() is deprecated and lacks support for higher link
speeds, so implement get_link_ksettings() instead.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. a buffer has 16 is_header flags, because that's its # of elements
2. replace the last occurrence of QETH_HEADER_SIZE, and remove it
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'elements_needed' is not used in qeth_do_send_packet_fast(),
so consequently remove it.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Duplicated code.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Identical code, we just need to call a layer-specific hook
to process any received buffer.
qeth_buffer_reclaim_work() is shuffled around to avoid a
forward declaration for qeth_queue_input_buffer().
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a number of layer-independent ioctls that we can handle
in core, and reduce code duplication. For layer-specific ioctls,
add a do_ioctl() discipline hook.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid endianness warnings reported by sparse by (1) using endianness
conversions for assigning and using network packet fields, and (2)
removing unnecessary endianness conversions from qeth_l3_rebuild_skb. No
functional changes.
Signed-off-by: Hans Wippel <hwippel@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. options.add_hhlen is set but never used, drop it
2. clean up no longer required forward declarations
3. delete all sorts of unused defines
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth_qdio_output_handler() is the only caller of
qeth_handle_send_error() and doesn't care about the return value.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depending on the device type, hard_start_xmit() builds different output
buffer formats. For instance with HiperSockets, on both L2 and L3 we
strip the ETH header from the skb - L3 doesn't need it, and L2 carries
it in the buffer's header element.
For this, we pass data_offset = ETH_HLEN all the way down to
__qeth_fill_buffer(), where skb->data is then adjusted accordingly.
But the initial size calculation still considers the *full* skb length
(including the ETH header). So qeth_get_elements_no() can erroneously
reject a skb as too big, even though it would actually fit into an
output buffer once the ETH header has been trimmed off later.
Fix this by passing an additional offset to qeth_get_elements_no(),
that indicates where in the skb the on-wire data actually begins.
Since the current code uses data_offset=-1 for some special handling
on OSA, we need to clamp data_offset to 0...
On HiperSockets this helps when sending ~MTU-size skbs with weird page
alignment. No change for OSA or AF_IUCV.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
STARTLAN needs to be the first IPA command after MPC initialization
completes.
So move the qeth_send_startlan() call from the layer disciplines
into the core path, right after the MPC handshake.
While at it, replace the magic LAN OFFLINE return code
with the existing enum.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework the RX/TX checksum offloading command sequence to use
the provided function call back mechanims to return card
data to the device driver.
Signed-off-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After device recovery, only a basic set of network device features is
enabled on the device. If features like checksum offloading or TSO were
enabled by the user before the recovery, this results in a mismatch
between the network device features, that the kernel assumes to be
enabled on the device, and the features actually enabled on the device.
This patch tries to restore previously set features, that require
changes on the device, after the recovery of a device. In case of an
error, the network device's features are changed to contain only the
features that are actually turned on.
Signed-off-by: Hans Wippel <hwippel@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a common set of fix_features and set_features
functions for layer 2 and layer 3. The RX, TX and TSO offload
functionality on the OSA card is enabled using ethtool at user's
request and not at device initialization as done before.
For layer 3 the RX checksum offloading is disabled at device
initialization time.
Signed-off-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In layer3 mode of the qeth driver, multicast IP addresses
from struct net_device and other type of IP addresses
from other sources require mapping to the OSA-card.
This patch simplifies the IP address mapping logic, and changes imple-
mentation of ndo_set_rx_mode callback and ip notifier events.
Addresses are stored in private hashtables instead of lists now.
It allows hardware registration/removal for new/deleted multicast
addresses only.
Signed-off-by: Lakhvich Dmitriy <ldmitriy@ru.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Evgeny Cherkashin <Eugene.Crosser@ru.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When skb data touches too many pages, skb_linearize() is called
opportunistically in the hope that less pages will be required
for a big linear buffer than for multiple fragments. This patch
intoduces a separate counter in ethtool statistics structure
representing _failed_ linearization attempts.
Signed-off-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Lakhvich Dmitriy <ldmitriy@ru.ibm.com>
Reviewed-by: Thomas Richter <tmricht@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
